| Age | Commit message (Collapse) | Author |
|---|
|
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
- Seagate IronWolf ST12000VN0008
- Seagate IronWolf ST8000NE0004
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d52a ("libata: change drive ready wait after hard reset to 5s")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Replace FS_CFLG_OWN_PAGES with a bit flag 'needs_bounce_pages' which has
the opposite meaning. I.e., filesystems now opt into the bounce page
pool instead of opt out. Make fscrypt_alloc_bounce_page() check that
the bounce page pool has been initialized.
I believe the opt-in makes more sense, since nothing else in
fscrypt_operations is opt-out, and these days filesystems can choose to
use blk-crypto which doesn't need the fscrypt bounce page pool. Also, I
happen to be planning to add two more flags, and I wanted to fix the
"FS_CFLG_" name anyway as it wasn't prefixed with "FSCRYPT_".
Link: https://lore.kernel.org/r/20230925055451.59499-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
fscrypt_operations::key_prefix should not be set by any filesystems that
aren't setting it already. This is already documented, but apparently
it's not sufficiently clear, as both ceph and btrfs have tried to set
it. Rename the field to legacy_key_prefix and improve the documentation
to hopefully make it clearer.
Link: https://lore.kernel.org/r/20230925055451.59499-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix EL2 Stage-1 MMIO mappings where a random address was used
- Fix SMCCC function number comparison when the SVE hint is set
RISC-V:
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
x86:
- Fixes for TSC_AUX virtualization
- Stop zapping page tables asynchronously, since we don't zap them as
often as before"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Do not use user return MSR support for virtualized TSC_AUX
KVM: SVM: Fix TSC_AUX virtualization setup
KVM: SVM: INTERCEPT_RDTSCP is never intercepted anyway
KVM: x86/mmu: Stop zapping invalidated TDP MMU roots asynchronously
KVM: x86/mmu: Do not filter address spaces in for_each_tdp_mmu_root_yield_safe()
KVM: x86/mmu: Open code leaf invalidation from mmu_notifier
KVM: riscv: selftests: Selectively filter-out AIA registers
KVM: riscv: selftests: Fix ISA_EXT register handling in get-reg-list
RISC-V: KVM: Fix riscv_vcpu_get_isa_ext_single() for missing extensions
RISC-V: KVM: Fix KVM_GET_REG_LIST API for ISA_EXT registers
KVM: selftests: Assert that vasprintf() is successful
KVM: arm64: nvhe: Ignore SVE hint in SMCCC function ID
KVM: arm64: Properly return allocated EL2 VA from hyp_alloc_private_va_range()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A collection of regression fixes, bug fixes, and some small cleanups
to the Compute Express Link code.
The regressions arrived in the v6.5 dev cycle and missed the v6.6
merge window due to my personal absences this cycle. The most
important fixes are for scenarios where the CXL subsystem fails to
parse valid region configurations established by platform firmware.
This is important because agreement between OS and BIOS on the CXL
configuration is fundamental to implementing "OS native" error
handling, i.e. address translation and component failure
identification.
Other important fixes are a driver load error when the BIOS lets the
Linux PCI core handle AER events, but not CXL memory errors.
The other fixex might have end user impact, but for now are only known
to trigger in our test/emulation environment.
Summary:
- Fix multiple scenarios where platform firmware defined regions fail
to be assembled by the CXL core.
- Fix a spurious driver-load failure on platforms that enable OS
native AER, but not OS native CXL error handling.
- Fix a regression detecting "poison" commands when "security"
commands are also defined.
- Fix a cxl_test regression with the move to centralize CXL port
register enumeration in the CXL core.
- Miscellaneous small fixes and cleanups"
* tag 'cxl-fixes-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/acpi: Annotate struct cxl_cxims_data with __counted_by
cxl/port: Fix cxl_test register enumeration regression
cxl/region: Refactor granularity select in cxl_port_setup_targets()
cxl/region: Match auto-discovered region decoders by HPA range
cxl/mbox: Fix CEL logic for poison and security commands
cxl/pci: Replace host_bridge->native_aer with pcie_aer_is_native()
PCI/AER: Export pcie_aer_is_native()
cxl/pci: Fix appropriate checking for _OSC while handling CXL RAS registers
|
|
The rcutorture_sched_setaffinity() function is needed by locktorture,
so move its declaration from rcu.h to torture.h and rename it to the
more generic torture_sched_setaffinity() name.
Please note that use of this function is still restricted to torture
tests, and of those, currently only rcutorture and locktorture.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
|
|
The current torture-test sleeps are waiting for a duration, but there
are situations where it is better to wait for an absolute time, for
example, when ending a stutter interval. This commit therefore adds
an hrtimer mode parameter to torture_hrtimeout_ns(). Why not also the
other torture_hrtimeout_*() functions? The theory is that most absolute
times will be in nanoseconds, especially not (say) jiffies.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
|
|
The deta angle and deta velocity channels were added in parallel with
color temperature and chromacity so this merge had to assign a
consistent order. I put the color related ones second.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add light chromaticity x and y.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-8-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In most cases, ambient color sensors also support light color temperature.
As a result, add support of light color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-4-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"13 hotfixes, 10 of which pertain to post-6.5 issues. The other three
are cc:stable"
* tag 'mm-hotfixes-stable-2023-09-23-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
proc: nommu: fix empty /proc/<pid>/maps
filemap: add filemap_map_order0_folio() to handle order0 folio
proc: nommu: /proc/<pid>/maps: release mmap read lock
mm: memcontrol: fix GFP_NOFS recursion in memory.high enforcement
pidfd: prevent a kernel-doc warning
argv_split: fix kernel-doc warnings
scatterlist: add missing function params to kernel-doc
selftests/proc: fixup proc-empty-vm test after KSM changes
revert "scripts/gdb/symbols: add specific ko module load command"
selftests: link libasan statically for tests with -fsanitize=address
task_work: add kerneldoc annotation for 'data' argument
mm: page_alloc: fix CMA and HIGHATOMIC landing on the wrong buddy list
sh: mm: re-add lost __ref to ioremap_prot() to fix modpost warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix lockdep, fix a boot failure, fix some build warnings, fix document
links, and some cleanups"
* tag 'loongarch-fixes-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
docs/zh_CN/LoongArch: Update the links of ABI
docs/LoongArch: Update the links of ABI
LoongArch: Don't inline kasan_mem_to_shadow()/kasan_shadow_to_mem()
kasan: Cleanup the __HAVE_ARCH_SHADOW_MAP usage
LoongArch: Set all reserved memblocks on Node#0 at initialization
LoongArch: Remove dead code in relocate_new_kernel
LoongArch: Use _UL() and _ULL()
LoongArch: Fix some build warnings with W=1
LoongArch: Fix lockdep static memory detection
|
|
HEAD
KVM/riscv fixes for 6.6, take #1
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
|
|
Pull xfs fixes from Chandan Babu:
- Fix an integer overflow bug when processing an fsmap call
- Fix crash due to CPU hot remove event racing with filesystem mount
operation
- During read-only mount, XFS does not allow the contents of the log to
be recovered when there are one or more unrecognized rcompat features
in the primary superblock, since the log might have intent items
which the kernel does not know how to process
- During recovery of log intent items, XFS now reserves log space
sufficient for one cycle of a permanent transaction to execute.
Otherwise, this could lead to livelocks due to non-availability of
log space
- On an fs which has an ondisk unlinked inode list, trying to delete a
file or allocating an O_TMPFILE file can cause the fs to the shutdown
if the first inode in the ondisk inode list is not present in the
inode cache. The bug is solved by explicitly loading the first inode
in the ondisk unlinked inode list into the inode cache if it is not
already cached
A similar problem arises when the uncached inode is present in the
middle of the ondisk unlinked inode list. This second bug is
triggered when executing operations like quotacheck and bulkstat. In
this case, XFS now reads in the entire ondisk unlinked inode list
- Enable LARP mode only on recent v5 filesystems
- Fix a out of bounds memory access in scrub
- Fix a performance bug when locating the tail of the log during
mounting a filesystem
* tag 'xfs-6.6-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: use roundup_pow_of_two instead of ffs during xlog_find_tail
xfs: only call xchk_stats_merge after validating scrub inputs
xfs: require a relatively recent V5 filesystem for LARP mode
xfs: make inode unlinked bucket recovery work with quotacheck
xfs: load uncached unlinked inodes into memory on demand
xfs: reserve less log space when recovering log intent items
xfs: fix log recovery when unknown rocompat bits are set
xfs: reload entire unlinked bucket lists
xfs: allow inode inactivation during a ro mount log recovery
xfs: use i_prev_unlinked to distinguish inodes that are not on the unlinked list
xfs: remove CPU hotplug infrastructure
xfs: remove the all-mounts list
xfs: use per-mount cpumask to track nonempty percpu inodegc lists
xfs: fix an agbno overflow in __xfs_getfsmap_datadev
xfs: fix per-cpu CIL structure aggregation racing with dying cpus
xfs: fix select in config XFS_ONLINE_SCRUB_STATS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Fix a include/linux/atomic/atomic-arch-fallback.h breakage that
generated incorrect code, and fix a lockdep reporting race that may
result in lockups"
* tag 'locking-urgent-2023-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlock: Do the lockdep annotation before locking in do_write_seqcount_begin_nested()
locking/atomic: scripts: fix fallback ifdeffery
|
|
Since the previous patch change to only account active requests when
we really allocate the driver tag, the RQF_MQ_INFLIGHT can be removed
and no double account problem.
1. none elevator: flush request will use the first pending request's
driver tag, won't double account.
2. other elevator: flush request will be accounted when allocate driver
tag when issue, and will be unaccounted when it put the driver tag.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-3-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cfi_private.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230915201206.never.107-kees@kernel.org
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct lpddr_private.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230915201159.never.112-kees@kernel.org
|
|
.discard.retpoline_safe sections do not have the SHF_ALLOC flag. These
sections referencing text sections' STT_SECTION symbols with PC-relative
relocations like R_386_PC32 [0] is conceptually not suitable. Newer
LLD will report warnings for REL relocations even for relocatable links [1]:
ld.lld: warning: vmlinux.a(drivers/i2c/busses/i2c-i801.o):(.discard.retpoline_safe+0x120): has non-ABS relocation R_386_PC32 against symbol ''
Switch to absolute relocations instead, which indicate link-time
addresses. In a relocatable link, these addresses are also output
section offsets, used by checks in tools/objtool/check.c. When linking
vmlinux, these .discard.* sections will be discarded, therefore it is
not a problem that R_X86_64_32 cannot represent a kernel address.
Alternatively, we could set the SHF_ALLOC flag for .discard.* sections,
but I think non-SHF_ALLOC for sections to be discarded makes more sense.
Note: if we decide to never support REL architectures (e.g. arm, i386),
we can utilize R_*_NONE relocations (.reloc ., BFD_RELOC_NONE, sym),
making .discard.* sections zero-sized. That said, the section content
waste is 4 bytes per entry, much smaller than sizeof(Elf{32,64}_Rel).
[0] commit 1c0c1faf5692 ("objtool: Use relative pointers for annotations")
[1] https://github.com/ClangBuiltLinux/linux/issues/1937
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20230920001728.1439947-1-maskray@google.com
|
|
The list_head counterpart of list_for_each_entry_reverse() was missing,
add it to complete the list handling APIs in <linux/list.h>.
[ This new API is also relied on by a WIP scheduler patch, so this
variant is not a theoretical possibility only. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
|
|
Some of the frequent consumers of get_cred and put_cred operate on 2
references on the same creds back-to-back.
Switch them to doing the work in one go instead.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
[PM: removed changelog from commit description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
Current release - regressions:
- bpf: adjust size_index according to the value of KMALLOC_MIN_SIZE
- netfilter: fix entries val in rule reset audit log
- eth: stmmac: fix incorrect rxq|txq_stats reference
Previous releases - regressions:
- ipv4: fix null-deref in ipv4_link_failure
- netfilter:
- fix several GC related issues
- fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
- eth: team: fix null-ptr-deref when team device type is changed
- eth: i40e: fix VF VLAN offloading when port VLAN is configured
- eth: ionic: fix 16bit math issue when PAGE_SIZE >= 64KB
Previous releases - always broken:
- core: fix ETH_P_1588 flow dissector
- mptcp: fix several connection hang-up conditions
- bpf:
- avoid deadlock when using queue and stack maps from NMI
- add override check to kprobe multi link attach
- hsr: properly parse HSRv1 supervisor frames.
- eth: igc: fix infinite initialization loop with early XDP redirect
- eth: octeon_ep: fix tx dma unmap len values in SG
- eth: hns3: fix GRE checksum offload issue"
* tag 'net-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
sfc: handle error pointers returned by rhashtable_lookup_get_insert_fast()
igc: Expose tx-usecs coalesce setting to user
octeontx2-pf: Do xdp_do_flush() after redirects.
bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
net: ena: Flush XDP packets on error.
net/handshake: Fix memory leak in __sock_create() and sock_alloc_file()
net: hinic: Fix warning-hinic_set_vlan_fliter() warn: variable dereferenced before check 'hwdev'
netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
netfilter: nf_tables: fix memleak when more than 255 elements expired
netfilter: nf_tables: disable toggling dormant table state more than once
vxlan: Add missing entries to vxlan_get_size()
net: rds: Fix possible NULL-pointer dereference
team: fix null-ptr-deref when team device type is changed
net: bridge: use DEV_STATS_INC()
net: hns3: add 5ms delay before clear firmware reset irq source
net: hns3: fix fail to delete tc flower rules during reset issue
net: hns3: only enable unicast promisc when mac table full
net: hns3: fix GRE checksum offload issue
net: hns3: add cmdq check for vf periodic service task
net: stmmac: fix incorrect rxq|txq_stats reference
...
|
|
This adds support for an async version of waitid(2), in a fully async
version. If an event isn't immediately available, wait for a callback
to trigger a retry.
The format of the sqe is as follows:
sqe->len The 'which', the idtype being queried/waited for.
sqe->fd The 'pid' (or id) being waited for.
sqe->file_index The 'options' being set.
sqe->addr2 A pointer to siginfo_t, if any, being filled in.
buf_index, add3, and waitid_flags are reserved/unused for now.
waitid_flags will be used for options for this request type. One
interesting use case may be to add multi-shot support, so that the
request stays armed and posts a notification every time a monitored
process state change occurs.
Note that this does not support rusage, on Arnd's recommendation.
See the waitid(2) man page for details on the arguments.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Finish off the 'simple' futex2 syscall group by adding
sys_futex_requeue(). Unlike sys_futex_{wait,wake}() its arguments are
too numerous to fit into a regular syscall. As such, use struct
futex_waitv to pass the 'source' and 'destination' futexes to the
syscall.
This syscall implements what was previously known as FUTEX_CMP_REQUEUE
and uses {val, uaddr, flags} for source and {uaddr, flags} for
destination.
This design explicitly allows requeueing between different types of
futex by having a different flags word per uaddr.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230921105248.511860556@noisy.programming.kicks-ass.net
|
|
To complement sys_futex_waitv()/wake(), add sys_futex_wait(). This
syscall implements what was previously known as FUTEX_WAIT_BITSET
except it uses 'unsigned long' for the value and bitmask arguments,
takes timespec and clockid_t arguments for the absolute timeout and
uses FUTEX2 flags.
The 'unsigned long' allows FUTEX2_SIZE_U64 on 64bit platforms.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230921105248.164324363@noisy.programming.kicks-ass.net
|
|
To complement sys_futex_waitv() add sys_futex_wake(). This syscall
implements what was previously known as FUTEX_WAKE_BITSET except it
uses 'unsigned long' for the bitmask and takes FUTEX2 flags.
The 'unsigned long' allows FUTEX2_SIZE_U64 on 64bit platforms.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230921105247.936205525@noisy.programming.kicks-ass.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull finegrained timestamp reverts from Christian Brauner:
"Earlier this week we sent a few minor fixes for the multi-grained
timestamp work in [1]. While we were polishing those up after Linus
realized that there might be a nicer way to fix them we received a
regression report in [2] that fine grained timestamps break gnulib
tests and thus possibly other tools.
The kernel will elide fine-grain timestamp updates when no one is
actively querying for them to avoid performance impacts. So a sequence
like write(f1) stat(f2) write(f2) stat(f2) write(f1) stat(f1) may
result in timestamp f1 to be older than the final f2 timestamp even
though f1 was last written too but the second write didn't update the
timestamp.
Such plotholes can lead to subtle bugs when programs compare
timestamps. For example, the nap() function in [2] will estimate that
it needs to wait one ns on a fine-grain timestamp enabled filesytem
between subsequent calls to observe a timestamp change. But in general
we don't update timestamps with more than one jiffie if we think that
no one is actively querying for fine-grain timestamps to avoid
performance impacts.
While discussing various fixes the decision was to go back to the
drawing board and ultimately to explore a solution that involves only
exposing such fine-grained timestamps to nfs internally and never to
userspace.
As there are multiple solutions discussed the honest thing to do here
is not to fix this up or disable it but to cleanly revert. The general
infrastructure will probably come back but there is no reason to keep
this code in mainline.
The general changes to timestamp handling are valid and a good cleanup
that will stay. The revert is fully bisectable"
Link: https://lore.kernel.org/all/20230918-hirte-neuzugang-4c2324e7bae3@brauner [1]
Link: https://lore.kernel.org/all/bf0524debb976627693e12ad23690094e4514303.camel@linuxfromscratch.org [2]
* tag 'v6.6-rc3.vfs.ctime.revert' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
Revert "fs: add infrastructure for multigrain timestamps"
Revert "btrfs: convert to multigrain timestamps"
Revert "ext4: switch to multigrain timestamps"
Revert "xfs: switch to multigrain timestamps"
Revert "tmpfs: add support for multigrain timestamps"
|
|
In some cases the OPP tables aren't specified in device tree, but rather
encoded in the FW. To allow a genpd provider to specify them dynamically
instead, let's add a new genpd flag, GENPD_FLAG_OPP_TABLE_FW.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-13-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
There are no longer any users of the ->device_domain_id() ops in the
scmi_perf_proto_ops, therefore let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-6-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Most scmi_perf_proto_ops are already using an "u32 domain" as an
in-parameter to indicate what performance domain we shall operate upon.
However, some of the ops are using a "struct device *dev", which means that
an additional OF parsing is needed each time the perf ops gets called, to
find the corresponding domain-id.
To avoid the above, but also to make the code more consistent, let's
replace the in-parameter "struct device *dev" with an "u32 domain". Note
that, this requires us to make some corresponding changes to the scmi
cpufreq driver, so let's do that too.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-5-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Similar to other protocol ops, it's useful for an scmi module driver to get
some generic information of a performance domain. Therefore, let's add a
new callback to provide this information. The information is currently
limited to the name of the performance domain and whether the set-level
operation is supported, although this can easily be extended if we find the
need for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-3-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Similar to other protocol ops, it's useful for an scmi module driver to get
the number of supported performance domains, hence let's make this
available by adding a new perf protocol callback. Note that, a user is
being added from subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-2-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
This adds handling of MSG_ZEROCOPY flag on transmission path:
1) If this flag is set and zerocopy transmission is possible (enabled
in socket options and transport allows zerocopy), then non-linear
skb will be created and filled with the pages of user's buffer.
Pages of user's buffer are locked in memory by 'get_user_pages()'.
2) Replaces way of skb owning: instead of 'skb_set_owner_sk_safe()' it
calls 'skb_set_owner_w()'. Reason of this change is that
'__zerocopy_sg_from_iter()' increments 'sk_wmem_alloc' of socket, so
to decrease this field correctly, proper skb destructor is needed:
'sock_wfree()'. This destructor is set by 'skb_set_owner_w()'.
3) Adds new callback to 'struct virtio_transport': 'can_msgzerocopy'.
If this callback is set, then transport needs extra check to be able
to send provided number of buffers in zerocopy mode. Currently, the
only transport that needs this callback set is virtio, because this
transport adds new buffers to the virtio queue and we need to check,
that number of these buffers is less than size of the queue (it is
required by virtio spec). vhost and loopback transports don't need
this check.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This is preparation patch for MSG_ZEROCOPY support. It adds handling of
non-linear skbs by replacing direct calls of 'memcpy_to_msg()' with
'skb_copy_datagram_iter()'. Main advantage of the second one is that it
can handle paged part of the skb by using 'kmap()' on each page, but if
there are no pages in the skb, it behaves like simple copying to iov
iterator. This patch also adds new field to the control block of skb -
this value shows current offset in the skb to read next portion of data
(it doesn't matter linear it or not). Idea behind this field is that
'skb_copy_datagram_iter()' handles both types of skb internally - it
just needs an offset from which to copy data from the given skb. This
offset is incremented on each read from skb. This approach allows to
simplify handling of both linear and non-linear skbs, because for
linear skb we need to call 'skb_pull()' after reading data from it,
while in non-linear case we need to update 'data_len'.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use the same _LINUX_SCHED_ prefix nomenclature as the other 29 header guards
in include/linux/sched/ do.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
It's the only non-trivial header in include/linux/sched/ missing a header guard.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Except on x86, preempt_count is always accessed with READ_ONCE().
Repeated invocations in macros like irq_count() produce repeated loads.
These redundant instructions appear in various fast paths. In the one
shown below, for example, irq_count() is evaluated during kernel entry
if !tick_nohz_full_cpu(smp_processor_id()).
0001ed0a <irq_enter_rcu>:
1ed0a: 4e56 0000 linkw %fp,#0
1ed0e: 200f movel %sp,%d0
1ed10: 0280 ffff e000 andil #-8192,%d0
1ed16: 2040 moveal %d0,%a0
1ed18: 2028 0008 movel %a0@(8),%d0
1ed1c: 0680 0001 0000 addil #65536,%d0
1ed22: 2140 0008 movel %d0,%a0@(8)
1ed26: 082a 0001 000f btst #1,%a2@(15)
1ed2c: 670c beqs 1ed3a <irq_enter_rcu+0x30>
1ed2e: 2028 0008 movel %a0@(8),%d0
1ed32: 2028 0008 movel %a0@(8),%d0
1ed36: 2028 0008 movel %a0@(8),%d0
1ed3a: 4e5e unlk %fp
1ed3c: 4e75 rts
This patch doesn't prevent the pointless btst and beqs instructions
above, but it does eliminate 2 of the 3 pointless move instructions
here and elsewhere.
On x86, preempt_count is per-cpu data and the problem does not arise
presumably because the compiler is free to optimize more effectively.
This patch was tested on m68k and x86. I was expecting no changes
to object code for x86 and mostly that's what I saw. However, there
were a few places where code generation was perturbed for some reason.
The performance issue addressed here is minor on uniprocessor m68k. I
got a 0.01% improvement from this patch for a simple "find /sys -false"
benchmark. For architectures and workloads susceptible to cache line bounce
the improvement is expected to be larger. The only SMP architecture I have
is x86, and as x86 unaffected I have not done any further measurements.
Fixes: 15115830c887 ("preempt: Cleanup the macro maze a bit")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/0a403120a682a525e6db2d81d1a3ffcc137c3742.1694756831.git.fthain@linux-m68k.org
|
|
do_write_seqcount_begin_nested()
It was brought up by Tetsuo that the following sequence:
write_seqlock_irqsave()
printk_deferred_enter()
could lead to a deadlock if the lockdep annotation within
write_seqlock_irqsave() triggers.
The problem is that the sequence counter is incremented before the lockdep
annotation is performed. The lockdep splat would then attempt to invoke
printk() but the reader side, of the same seqcount, could have a
tty_port::lock acquired waiting for the sequence number to become even again.
The other lockdep annotations come before the actual locking because "we
want to see the locking error before it happens". There is no reason why
seqcount should be different here.
Do the lockdep annotation first then perform the locking operation (the
sequence increment).
Fixes: 1ca7d67cf5d5a ("seqcount: Add lockdep functionality to seqcount/seqlock structures")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230920104627._DTHgPyA@linutronix.de
Closes: https://lore.kernel.org/20230621130641.-5iueY1I@linutronix.de
|
|
This reverts commit ffb6cf19e06334062744b7e3493f71e500964f8e.
Users reported regressions due to enabling multi-grained timestamps
unconditionally. As no clear consensus on a solution has come up and the
discussion has gone back to the drawing board revert the infrastructure
changes for. If it isn't code that's here to stay, make it go away.
Message-ID: <20230920-keine-eile-c9755b5825db@brauner>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Expose a couple of new SCMI clock operations to get and set OEM specific
clock configurations when talking to an SCMI v3.2 compliant.
Issuing such requests against an SCMI platform server not supporting v3.2
extension for OEM specific clock configurations will fail.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230826125308.462328-7-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Add support for v3.2 clock CONFIG_GET command and related new clock
protocol operation state_get() to retrieve the status of a clock.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230826125308.462328-4-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
SCMI clock enable/disable operations come in 2 different flavours which
simply just differ in how the underlying SCMI transactions is carried on:
atomic or not.
Currently we expose such SCMI operations through 2 distinctly named
wrappers, that, in turn, are wrapped into another couple of similarly and
distinctly named callbacks inside SCMI clock driver user.
Reduce the churn of duplicated wrappers by adding a param to SCMI clock
enable/disable operations to ask for atomic operation while removing the
_atomic version of such operations.
No functional change.
CC: Michael Turquette <mturquette@baylibre.com>
CC: Stephen Boyd <sboyd@kernel.org>
CC: linux-clk@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230826125308.462328-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Since commit:
9257959a6e5b4fca ("locking/atomic: scripts: restructure fallback ifdeffery")
The ordering fallbacks for atomic*_read_acquire() and
atomic*_set_release() erroneously fall back to the implictly relaxed
atomic*_read() and atomic*_set() variants respectively, without any
additional barriers. This loses the ACQUIRE and RELEASE ordering
semantics, which can result in a wide variety of problems, even on
strongly-ordered architectures where the implementation of
atomic*_read() and/or atomic*_set() allows the compiler to reorder those
relative to other accesses.
In practice this has been observed to break bit spinlocks on arm64,
resulting in dentry cache corruption.
The fallback logic was intended to allow ACQUIRE/RELEASE/RELAXED ops to
be defined in terms of FULL ops, but where an op had RELAXED ordering by
default, this unintentionally permitted the ACQUIRE/RELEASE ops to be
defined in terms of the implicitly RELAXED default.
This patch corrects the logic to avoid falling back to implicitly
RELAXED ops, resulting in the same behaviour as prior to commit
9257959a6e5b4fca.
I've verified the resulting assembly on arm64 by generating outlined
wrappers of the atomics. Prior to this patch the compiler generates
sequences using relaxed load (LDR) and store (STR) instructions, e.g.
| <outlined_atomic64_read_acquire>:
| ldr x0, [x0]
| ret
|
| <outlined_atomic64_set_release>:
| str x1, [x0]
| ret
With this patch applied the compiler generates sequences using the
intended load-acquire (LDAR) and store-release (STLR) instructions, e.g.
| <outlined_atomic64_read_acquire>:
| ldar x0, [x0]
| ret
|
| <outlined_atomic64_set_release>:
| stlr x1, [x0]
| ret
To make sure that there were no other victims of the ifdeffery rewrite,
I generated outlined copies of all of the {atomic,atomic64,atomic_long}
atomic operations before and after commit 9257959a6e5b4fca. A diff of
the generated assembly on arm64 shows that only the read_acquire() and
set_release() operations were changed, and only lost their intended
ordering:
| [mark@lakrids:~/src/linux]% diff -u \
| <(aarch64-linux-gnu-objdump -d before-9257959a6e5b4fca.o)
| <(aarch64-linux-gnu-objdump -d after-9257959a6e5b4fca.o)
| --- /proc/self/fd/11 2023-09-19 16:51:51.114779415 +0100
| +++ /proc/self/fd/16 2023-09-19 16:51:51.114779415 +0100
| @@ -1,5 +1,5 @@
|
| -before-9257959a6e5b4fca.o: file format elf64-littleaarch64
| +after-9257959a6e5b4fca.o: file format elf64-littleaarch64
|
|
| Disassembly of section .text:
| @@ -9,7 +9,7 @@
| 4: d65f03c0 ret
|
| 0000000000000008 <outlined_atomic_read_acquire>:
| - 8: 88dffc00 ldar w0, [x0]
| + 8: b9400000 ldr w0, [x0]
| c: d65f03c0 ret
|
| 0000000000000010 <outlined_atomic_set>:
| @@ -17,7 +17,7 @@
| 14: d65f03c0 ret
|
| 0000000000000018 <outlined_atomic_set_release>:
| - 18: 889ffc01 stlr w1, [x0]
| + 18: b9000001 str w1, [x0]
| 1c: d65f03c0 ret
|
| 0000000000000020 <outlined_atomic_add>:
| @@ -1230,7 +1230,7 @@
| 1070: d65f03c0 ret
|
| 0000000000001074 <outlined_atomic64_read_acquire>:
| - 1074: c8dffc00 ldar x0, [x0]
| + 1074: f9400000 ldr x0, [x0]
| 1078: d65f03c0 ret
|
| 000000000000107c <outlined_atomic64_set>:
| @@ -1238,7 +1238,7 @@
| 1080: d65f03c0 ret
|
| 0000000000001084 <outlined_atomic64_set_release>:
| - 1084: c89ffc01 stlr x1, [x0]
| + 1084: f9000001 str x1, [x0]
| 1088: d65f03c0 ret
|
| 000000000000108c <outlined_atomic64_add>:
| @@ -2427,7 +2427,7 @@
| 207c: d65f03c0 ret
|
| 0000000000002080 <outlined_atomic_long_read_acquire>:
| - 2080: c8dffc00 ldar x0, [x0]
| + 2080: f9400000 ldr x0, [x0]
| 2084: d65f03c0 ret
|
| 0000000000002088 <outlined_atomic_long_set>:
| @@ -2435,7 +2435,7 @@
| 208c: d65f03c0 ret
|
| 0000000000002090 <outlined_atomic_long_set_release>:
| - 2090: c89ffc01 stlr x1, [x0]
| + 2090: f9000001 str x1, [x0]
| 2094: d65f03c0 ret
|
| 0000000000002098 <outlined_atomic_long_add>:
I've build tested this with a variety of configs for alpha, arm, arm64,
csky, i386, m68k, microblaze, mips, nios2, openrisc, powerpc, riscv,
s390, sh, sparc, x86_64, and xtensa, for which I've seen no issues. I
was unable to build test for ia64 and parisc due to existing build
breakage in v6.6-rc2.
Fixes: 9257959a6e5b4fca ("locking/atomic: scripts: restructure fallback ifdeffery")
Reported-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Baokun Li <libaokun1@huawei.com>
Link: https://lkml.kernel.org/r/20230919171430.2697727-1-mark.rutland@arm.com
|
|
With PREEMPT_RT there is a rt_mutex recursion problem where
sched_submit_work() can use an rtlock (aka spinlock_t). More
specifically what happens is:
mutex_lock() /* really rt_mutex */
...
__rt_mutex_slowlock_locked()
task_blocks_on_rt_mutex()
// enqueue current task as waiter
// do PI chain walk
rt_mutex_slowlock_block()
schedule()
sched_submit_work()
...
spin_lock() /* really rtlock */
...
__rt_mutex_slowlock_locked()
task_blocks_on_rt_mutex()
// enqueue current task as waiter *AGAIN*
// *CONFUSION*
Fix this by making rt_mutex do the sched_submit_work() early, before
it enqueues itself as a waiter -- before it even knows *if* it will
wait.
[[ basically Thomas' patch but with different naming and a few asserts
added ]]
Originally-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230908162254.999499-5-bigeasy@linutronix.de
|
|
Add new health error syndrome to indicate that pci data poisoned error
has been received while fetching device ICM data.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In order to have mcast offloads the driver needs the following:
It should know if that mcast comes from wire port, in addition the flow
should not be marked as any specific source, that way it will give the
flexibility for the driver not to be depended on the way iterator
implemented in the FW.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As Linus suggested, __HAVE_ARCH_XYZ is "stupid" and "having historical
uses of it doesn't make it good". So migrate __HAVE_ARCH_SHADOW_MAP to
separate macros named after the respective functions.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
