| Age | Commit message (Collapse) | Author |
|---|
|
xhci_sideband_remove_endpoint() incorrecly assumes that the endpoint is
running and has a valid transfer ring.
Lianqin reported a crash during suspend/wake-up stress testing, and
found the cause to be dereferencing a non-existing transfer ring
'ep->ring' during xhci_sideband_remove_endpoint().
The endpoint and its ring may be in unknown state if this function
is called after xHCI was reinitialized in resume (lost power), or if
device is being re-enumerated, disconnected or endpoint already dropped.
Fix this by both removing unnecessary ring access, and by checking
ep->ring exists before dereferencing it. Also make sure endpoint is
running before attempting to stop it.
Remove the xhci_initialize_ring_info() call during sideband endpoint
removal as is it only initializes ring structure enqueue, dequeue and
cycle state values to their starting values without changing actual
hardware enqueue, dequeue and cycle state. Leaving them out of sync
is worse than leaving it as it is. The endpoint will get freed in after
this in most usecases.
If the (audio) class driver want's to reuse the endpoint after offload
then it is up to the class driver to ensure endpoint is properly set up.
Reported-by: 胡连勤 <hulianqin@vivo.com>
Closes: https://lore.kernel.org/linux-usb/TYUPR06MB6217B105B059A7730C4F6EC8D2B9A@TYUPR06MB6217.apcprd06.prod.outlook.com/
Tested-by: 胡连勤 <hulianqin@vivo.com>
Fixes: de66754e9f80 ("xhci: sideband: add initial api to register a secondary interrupter entity")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260115233758.364097-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB serial fix for 6.19-rc6
Here's a fix for an f81232 enumeration issue that could prevent some
ports from being enabled (e.g. during driver rebind).
Included are also some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.19-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: f81232: fix incomplete serial port generation
USB: serial: ftdi_sio: add support for PICAXE AXE027 cable
USB: serial: option: add Telit LE910 MBIM composition
|
|
Based on the reality[1][2] that vb2_dma_sg_alloc() can't alloc buffer with
device DMA limits, those device will always get below error: "swiotlb
buffer is full (sz: 393216 bytes), total 65536 (slots), used 2358 (slots)"
and the uvc gadget function can't work at all.
The videobuf2-dma-sg.c driver doesn't has a formal improve about this issue
till now. For UVC gadget, the videobuf2 subsystem doesn't do dma_map() on
vmalloc returned big buffer when allocate the video buffers, however, it do
it for dma_sg returned buffer. So the issue happens for vb2_dma_sg_alloc().
To workaround the issue, lets retry vb2_reqbufs() with
vb_vmalloc_memops if it fails to allocate buffer with vb2_dma_sg_memops.
If use vmalloced buffer, UVC gadget will allocate some small buffers for
each usb_request to do dma transfer, then uvc driver will memcopy data
from big buffer to small buffer.
Link[1]: https://lore.kernel.org/linux-media/20230828075420.2009568-1-anle.pan@nxp.com/
Link[2]: https://lore.kernel.org/linux-media/20230914145812.12851-1-hui.fang@nxp.com/
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-4-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uvcg_queue_init() may fail, but its return value is currently ignored.
Propagate the error code from uvcg_queue_init() to correctly report
initialization failures.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-3-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to USB specification:
For full-/high-speed isochronous endpoints, the bInterval value is
used as the exponent for a 2^(bInterval-1) value.
To correctly convert bInterval as interval_duration:
interval_duration = 2^(bInterval-1) * frame_interval
Because the unit of video->interval is 100ns, add a comment info to
make it clear.
Fixes: 48dbe731171e ("usb: gadget: uvc: set req_size and n_requests based on the frame interval")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-2-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current req_payload_size calculation has 2 issue:
(1) When the first time calculate req_payload_size for all the buffers,
reqs_per_frame = 0 will be the divisor of DIV_ROUND_UP(). So
the result is undefined.
This happens because VIDIOC_STREAMON is always executed after
VIDIOC_QBUF. So video->reqs_per_frame will be 0 until VIDIOC_STREAMON
is run.
(2) The buf->req_payload_size may be bigger than max_req_size.
Take YUYV pixel format as example:
If bInterval = 1, video->interval = 666666, high-speed:
video->reqs_per_frame = 666666 / 1250 = 534
720p: buf->req_payload_size = 1843200 / 534 = 3452
1080p: buf->req_payload_size = 4147200 / 534 = 7766
Based on such req_payload_size, the controller can't run normally.
To fix above issue, assign max_req_size to buf->req_payload_size when
video->reqs_per_frame = 0. And limit buf->req_payload_size to
video->req_size if it's large than video->req_size. Since max_req_size
is used at many place, add it to struct uvc_video and set the value once
endpoint is enabled.
Fixes: 98ad03291560 ("usb: gadget: uvc: set req_length based on payload by nreqs instead of req_size")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-1-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ignore USB role switches if dwc3-apple is already in the desired state.
The USB-C port controller on M2 and M1/M2 Pro/Max/Ultra devices issues
additional interrupts which result in USB role switches to the already
active role.
Ignore these USB role switches to ensure the USB-C port controller and
dwc3-apple are always in a consistent state. This matches the behaviour
in __dwc3_set_mode() in core.c.
Fixes detecting USB 2.0 and 3.x devices on the affected systems. The
reset caused by the additional role switch appears to leave the USB
devices in a state which prevents detection when the phy and dwc3 is
brought back up again.
Fixes: 0ec946d32ef7 ("usb: dwc3: Add Apple Silicon DWC3 glue layer driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sven Peter <sven@kernel.org>
Tested-by: Sven Peter <sven@kernel.org> # M1 mac mini and macbook air
Link: https://patch.msgid.link/20260109-apple-dwc3-role-switch-v1-1-11623b0f6222@jannau.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When some wake IRQs are disabled in the device tree, the corresponding
interrupt entries are removed from DT. In such cases, the driver
currently calls platform_get_irq(), which returns -ENXIO and logs
an error like:
tegra-xusb 3610000.usb: error -ENXIO: IRQ index 2 not found
However, not all wake IRQs are mandatory. The hardware can operate
normally even if some wake sources are not defined in DT. To avoid this
false alarm and allow missing wake IRQs gracefully, use
platform_get_irq_optional() instead of platform_get_irq().
Fixes: 5df186e2ef11 ("usb: xhci: tegra: Support USB wakeup function for Tegra234")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wei-Cheng Chen <weichengc@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260112145653.95691-1-weichengc@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 9beeee6584b9aa4f ("USB: EHCI: log a warning if ehci-hcd is not
loaded first") said that ehci-hcd should be loaded before ohci-hcd and
uhci-hcd. However, commit 05c92da0c52494ca ("usb: ohci/uhci - add soft
dependencies on ehci_pci") only makes ohci-pci/uhci-pci depend on ehci-
pci, which is not enough and we may still see the warnings in boot log.
To eliminate the warnings we should make ohci-hcd/uhci-hcd depend on
ehci-hcd. But Alan said that the warning introduced by 9beeee6584b9aa4f
is bogus, we only need the soft dependencies in the PCI level rather
than the HCD level.
However, there is really another neccessary soft dependencies between
ohci-platform/uhci-platform and ehci-platform, which is added by this
patch. The boot logs are below.
1. ohci-platform loaded before ehci-platform:
ohci-platform 1f058000.usb: Generic Platform OHCI controller
ohci-platform 1f058000.usb: new USB bus registered, assigned bus number 1
ohci-platform 1f058000.usb: irq 28, io mem 0x1f058000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
usb 1-4: new low-speed USB device number 2 using ohci-platform
ehci-platform 1f050000.usb: EHCI Host Controller
ehci-platform 1f050000.usb: new USB bus registered, assigned bus number 2
ehci-platform 1f050000.usb: irq 29, io mem 0x1f050000
ehci-platform 1f050000.usb: USB 2.0 started, EHCI 1.00
usb 1-4: device descriptor read/all, error -62
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 1-4: new low-speed USB device number 3 using ohci-platform
input: YSPRINGTECH USB OPTICAL MOUSE as /devices/platform/bus@10000000/1f058000.usb/usb1/1-4/1-4:1.0/0003:10C4:8105.0001/input/input0
hid-generic 0003:10C4:8105.0001: input,hidraw0: USB HID v1.11 Mouse [YSPRINGTECH USB OPTICAL MOUSE] on usb-1f058000.usb-4/input0
2. ehci-platform loaded before ohci-platform:
ehci-platform 1f050000.usb: EHCI Host Controller
ehci-platform 1f050000.usb: new USB bus registered, assigned bus number 1
ehci-platform 1f050000.usb: irq 28, io mem 0x1f050000
ehci-platform 1f050000.usb: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci-platform 1f058000.usb: Generic Platform OHCI controller
ohci-platform 1f058000.usb: new USB bus registered, assigned bus number 2
ohci-platform 1f058000.usb: irq 29, io mem 0x1f058000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 2-4: new low-speed USB device number 2 using ohci-platform
input: YSPRINGTECH USB OPTICAL MOUSE as /devices/platform/bus@10000000/1f058000.usb/usb2/2-4/2-4:1.0/0003:10C4:8105.0001/input/input0
hid-generic 0003:10C4:8105.0001: input,hidraw0: USB HID v1.11 Mouse [YSPRINGTECH USB OPTICAL MOUSE] on usb-1f058000.usb-4/input0
In the later case, there is no re-connection for USB-1.0/1.1 devices,
which is expected.
Cc: stable <stable@kernel.org>
Reported-by: Shengwen Xiao <atzlinux@sina.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260112084802.1995923-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the upstream code has been getting broader test coverage by our
users we occasionally see issues with USB2 devices plugged in during boot.
Before Linux is running, the USB2 PHY has usually been running in device
mode and it turns out that sometimes host->device or device->host
transitions don't work.
The root cause: If the role inside the USB2 PHY is re-configured when it
has already been powered on or when dwc3 has already enabled the ULPI
interface the new configuration sometimes doesn't take affect until dwc3
is reset again. Fix this rare issue by configuring the role much earlier.
Note that the USB3 PHY does not suffer from this issue and actually
requires dwc3 to be up before the correct role can be configured there.
Reported-by: James Calligeros <jcalligeros99@gmail.com>
Reported-by: Janne Grunau <j@jannau.net>
Fixes: 0ec946d32ef7 ("usb: dwc3: Add Apple Silicon DWC3 glue layer driver")
Cc: stable <stable@kernel.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20260109-dwc3-apple-usb2phy-fix-v2-1-ab6b041e3b26@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Fintek F81532A/534A/535/536 family relies on the
F81534A_CTRL_CMD_ENABLE_PORT (116h) register during initialization to
both determine serial port status and control port creation. If the
driver experiences fast load/unload cycles, the device state may becomes
unstable, resulting in the incomplete generation of serial ports.
Performing a dummy read operation on the register prior to the initial
write command resolves the issue. This clears the device's stale internal
state. Subsequent write operations will correctly generate all serial
ports.
This patch also removes the retry loop in f81534a_ctrl_set_register()
because the stale state has been fixed.
Tested on: HygonDM1SLT(Hygon C86 3250 8-core Processor)
Signed-off-by: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The vendor provides instructions to write "0403 bd90" to
/sys/bus/usb-serial/drivers/ftdi_sio/new_id; see:
https://picaxe.com/docs/picaxe_linux_instructions.pdf
Cc: stable@vger.kernel.org
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for Telit LE910 module when operating in MBIM composition
with additional ttys. This USB product ID is used by the module
when AT#USBCFG is set to 7.
0x1252: MBIM + tty(NMEA) + tty(MODEM) + tty(MODEM) + SAP
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1252 Rev=03.18
S: Manufacturer=Android
S: Product=LE910C1-EU
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
Signed-off-by: Ulrich Mohr <u.mohr@semex-engcon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add USB_QUIRK_NO_BOS quirk flag to skip requesting the BOS descriptor
for devices that cannot handle it.
Add Elgato 4K X (0fd9:009b) to the quirk table. This device hangs when
the BOS descriptor is requested at SuperSpeed Plus (10Gbps).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220027
Cc: stable <stable@kernel.org>
Signed-off-by: Johannes Brüderl <johannes.bruederl@gmail.com>
Link: https://patch.msgid.link/20251207090220.14807-1-johannes.bruederl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ports are defined in the tcpc main node, fwnode_usb_role_switch_get()
returns an error, meaning usb_role_switch_get() (which would succeed)
never gets a chance to run as port->role_sw isn't NULL, causing a
regression on devices where this is the case.
Fix this by turning the NULL check into IS_ERR_OR_NULL(), so
usb_role_switch_get() can actually run and the device get properly probed.
Fixes: 2d8713f807a4 ("tcpm: switch check for role_sw device with fw_node")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Link: https://patch.msgid.link/20260105-fix-ppp-power-v2-1-6924f5a41224@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Synopsys renamed DWC_usb32 IP to DWC_usb4 as of IP version 1.30. No
functional change except checking for the IP_NAME here. The driver will
treat the new IP_NAME as if it's DWC_usb32. Additional features for USB4
will be introduced and checked separately.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/e6f1827754c7a7ddc5eb7382add20bfe3a9b312f.1767390747.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Johan Hovold <johan@kernel.org> says:
The new buffer management code has not been tested or reviewed properly
and breaks boot of machines like the Lenovo ThinkPad X13s.
Fixing this will require designing a proper interface for managing these
transactions, something which most likely involves reverting most of the
offending commit anyway.
Revert the broken code to fix the regression and let Intel come up with
a properly tested implementation for a later kernel.
Link: https://lore.kernel.org/r/20251222152204.2846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
message out fields"
This reverts commit 3e082978c33151d576694deac8abde021ea669a8.
The new buffer management code has not been tested or reviewed properly
and breaks boot of machines like the Lenovo ThinkPad X13s:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000000
CPU: 0 UID: 0 PID: 813 Comm: kworker/0:3 Not tainted 6.19.0-rc2 #26 PREEMPT
Hardware name: LENOVO 21BYZ9SRUS/21BYZ9SRUS, BIOS N3HET87W (1.59 ) 12/05/2023
Workqueue: events ucsi_handle_connector_change [typec_ucsi]
Call trace:
ucsi_sync_control_common+0xe4/0x1ec [typec_ucsi] (P)
ucsi_run_command+0xcc/0x194 [typec_ucsi]
ucsi_send_command_common+0x84/0x2a0 [typec_ucsi]
ucsi_get_connector_status+0x48/0x78 [typec_ucsi]
ucsi_handle_connector_change+0x5c/0x4f4 [typec_ucsi]
process_one_work+0x208/0x60c
worker_thread+0x244/0x388
The new code completely ignores concurrency so that the message length
can be updated while a transaction is ongoing. In the above case, the
length ends up being modified by another thread while processing an ack
so that the NULL cci pointer is dereferenced.
Fixing this will require designing a proper interface for managing these
transactions, something which most likely involves reverting most of the
offending commit anyway.
Revert the broken code to fix the regression and let Intel come up with
a properly tested implementation for a later kernel.
Fixes: 3e082978c331 ("usb: typec: ucsi: Update UCSI structure to have message in and message out fields")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-5-johan@kernel.org
|
|
This reverts commit db0028637cc832add6d87564fcc2ebb12781b046.
The new buffer management code that this feature relies on is broken so
revert for now.
As for the in buffer, nothing prevents the out message size and buffer
from being modified while the message is being processed due to lack of
serialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-4-johan@kernel.org
|
|
This reverts commit 775fae520e6ae62c393a8daf42dc534f09692f3f.
The new buffer management code that this relies on is broken so revert
for now.
It also looks like the error handling needs some more thought as the
message out size is not reset on errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-3-johan@kernel.org
|
|
This reverts commit 1b474ee01fbb73b1365adbf9b3067f7375e471ee.
The new buffer management code that this feature relies on is broken so
revert for now.
The interface for writing data and support for UCSI_SET_PDOS looks like
it could use some more thought as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-2-johan@kernel.org
|
|
ucsi_sync_control_common"
This reverts commit 14ad4c10d5bdd413ff9a914260e89b5f54b7a2c7.
The originally offending commit will be reverted instead of this fix up
at this point in time, so revert this fix.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Mario Limonciello (AMD) <superm1@kernel.org>
Cc: stable <stable@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Fixes: 14ad4c10d5bd ("usb: typec: ucsi: Fix null pointer dereference in ucsi_sync_control_common")
Link: https://lore.kernel.org/r/20251222152204.2846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5106dbab44fba8ec6dede3f4e75d17f5aa777ec8.
There are reported issues in this file, so revert the commit for now so
that the original offending changes can be reverted and working systems
can be restored. This can come back at a later time if it is rebased
yet-again (sorry.)
Cc: stable <stable@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20251222152204.2846-1-johan@kernel.org
Fixes: 5106dbab44fb ("usb: typec: ucsi: Get connector status after enable notifications")
Cc: Kenneth R. Crudup <kenny@panix.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hsin-Te Yuan <yuanhsinte@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Error labels should be named after what they do rather than after from
where they are jumped to.
Rename the probe error labels for consistency and to improve
readability.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Error labels should be named after what they do rather than after from
where they are jumped to.
Rename the probe error labels for consistency and to improve
readability.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to drop the reference taken when looking up the PHY I2C device
during probe on probe failure (e.g. probe deferral) and on driver
unbind.
Fixes: 73108aa90cbf ("USB: ohci-nxp: Use isp1301 driver")
Cc: stable@vger.kernel.org # 3.5
Reported-by: Ma Ke <make24@iscas.ac.cn>
Link: https://lore.kernel.org/lkml/20251117013428.21840-1-make24@iscas.ac.cn/
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent change fixing a device reference leak in a UDC driver
introduced a potential use-after-free in the non-OF case as the
isp1301_get_client() helper only increases the reference count for the
returned I2C device in the OF case.
Increment the reference count also for non-OF so that the caller can
decrement it unconditionally.
Note that this is inherently racy just as using the returned I2C device
is since nothing is preventing the PHY driver from being unbound while
in use.
Fixes: c84117912bdd ("USB: lpc32xx_udc: Fix error handling in probe")
Cc: stable@vger.kernel.org
Cc: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent change fixing a device reference leak introduced a clock
imbalance by reusing an error path so that the clock may be disabled
before having been enabled.
Note that the clock framework allows for passing in NULL clocks so there
is no risk for a NULL pointer dereference.
Also drop the bogus I2C client NULL check added by the offending commit
as the pointer has already been verified to be non-NULL.
Fixes: c84117912bdd ("USB: lpc32xx_udc: Fix error handling in probe")
Cc: stable@vger.kernel.org
Cc: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Originally, the notification for connector change will be enabled after
the first read of the connector status. Therefore, if the event happens
during this window, it will be missing and make the status unsynced.
Get the connector status only after enabling the notification for
connector change to ensure the status is synced.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: stable <stable@kernel.org>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Link: https://patch.msgid.link/20251218-ucsi-v7-1-aea83e83fb12@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We cannot determine which models require the NO_ATA_1X and
IGNORE_RESIDUE quirks aside from the EL-R12 optical drive device.
Fixes: 955a48a5353f ("usb: usb-storage: No additional quirks need to be added to the EL-R12 optical drive.")
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Link: https://patch.msgid.link/20251218012318.15978-1-chenchangcheng@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When clk_bulk_prepare_enable() fails, the error path jumps to
err_resetc_assert, skipping clk_bulk_put_all() and leaking the
clock references acquired by clk_bulk_get_all().
Add err_clk_put_all label to properly release clock resources
in all error paths.
Found via static analysis and code review.
Fixes: c0c61471ef86 ("usb: dwc3: of-simple: Convert to bulk clk API")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20251211064937.2360510-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing null check for cci parameter before dereferencing it in
ucsi_sync_control_common(). The function can be called with cci=NULL
from ucsi_acknowledge(), which leads to a null pointer dereference
when accessing *cci in the condition check.
The crash occurs because the code checks if cci is not null before
calling ucsi->ops->read_cci(ucsi, cci), but then immediately
dereferences cci without a null check in the following condition:
(*cci & UCSI_CCI_COMMAND_COMPLETE).
KASAN trace:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:ucsi_sync_control_common+0x2ae/0x4e0 [typec_ucsi]
Cc: stable <stable@kernel.org>
Fixes: 667ecac55861 ("usb: typec: ucsi: return CCI and message from sync_control callback")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20251216122210.5457-1-superm1@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lpc32xx_udc_probe() acquires an i2c_client reference through
isp1301_get_client() but fails to release it in both error handling
paths and the normal removal path. This could result in a reference
count leak for the I2C device, preventing proper cleanup and potentially
leading to resource exhaustion. Add put_device() to release the
reference in the probe failure path and in the remove function.
Calling path: isp1301_get_client() -> of_find_i2c_device_by_node() ->
i2c_find_device_by_fwnode(). As comments of i2c_find_device_by_fwnode()
says, 'The user must call put_device(&client->dev) once done with the
i2c client.'
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20251215020931.15324-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dp_altmode_probe()
In error paths, call typec_altmode_put_plug() to drop the device reference
obtained by typec_altmode_get_plug().
Fixes: 71ba4fe56656 ("usb: typec: altmodes/displayport: add SOP' support")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20251206070445.190770-1-lihaoxiang@isrc.iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The delayed work item otg_event is initialized in fsl_otg_conf() and
scheduled under two conditions:
1. When a host controller binds to the OTG controller.
2. When the USB ID pin state changes (cable insertion/removal).
A race condition occurs when the device is removed via fsl_otg_remove():
the fsl_otg instance may be freed while the delayed work is still pending
or executing. This leads to use-after-free when the work function
fsl_otg_event() accesses the already freed memory.
The problematic scenario:
(detach thread) | (delayed work)
fsl_otg_remove() |
kfree(fsl_otg_dev) //FREE| fsl_otg_event()
| og = container_of(...) //USE
| og-> //USE
Fix this by calling disable_delayed_work_sync() in fsl_otg_remove()
before deallocating the fsl_otg structure. This ensures the delayed work
is properly canceled and completes execution prior to memory deallocation.
This bug was identified through static analysis.
Fixes: 0807c500a1a6 ("USB: add Freescale USB OTG Transceiver driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://patch.msgid.link/20251205034831.12846-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbhsp_get_pipe() set pipe's flags to IS_USED. In error paths,
usbhsp_put_pipe() is required to clear pipe's flags to prevent
pipe exhaustion.
Fixes: f1407d5c6624 ("usb: renesas_usbhs: Add Renesas USBHS common code")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20251204132129.109234-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Selecting DRM_AUX_HPD_BRIDGE is not possible from a built-in driver when
CONFIG_DRM=m:
WARNING: unmet direct dependencies detected for DRM_AUX_HPD_BRIDGE
Depends on [m]: HAS_IOMEM [=y] && DRM [=m] && DRM_BRIDGE [=y] && OF [=y]
Selected by [y]:
- UCSI_HUAWEI_GAOKUN [=y] && USB_SUPPORT [=y] && TYPEC [=y] && TYPEC_UCSI [=y] && EC_HUAWEI_GAOKUN [=y] && DRM_BRIDGE [=y] && OF [=y]
Add the same dependency we have in similar drivers to work around this.
Fixes: 00327d7f2c8c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20251204101111.1035975-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platforms, switching USB roles from host to device can trigger
controller faults due to premature PHY power-down. This occurs when the
PHY is disabled too early during teardown, causing synchronization
issues between the PHY and controller.
Keep susphy enabled during dwc3_host_exit() and dwc3_gadget_exit()
ensures the PHY remains in a low-power state capable of handling
required commands during role switch.
Cc: stable <stable@kernel.org>
Fixes: 6d735722063a ("usb: dwc3: core: Prevent phy suspend during init")
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Udipto Goswami <udipto.goswami@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20251126054221.120638-1-udipto.goswami@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixup replaces tty_vhangup() call with call to
tty_port_tty_vhangup(). Both calls hangup tty device
synchronously however tty_port_tty_vhangup() increases
reference count during the hangup operation using
scoped_guard(tty_port_tty).
Cc: stable <stable@kernel.org>
Fixes: 1f73b8b56cf3 ("xhci: dbgtty: fix device unregister")
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://patch.msgid.link/20251127111644.3161386-1-ukaszb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
6.19-rc1. Nothing major here, just lots of tiny updates for most of
the common USB drivers. Included in here are:
- more xhci driver updates and fixes
- Thunderbolt driver cleanups
- usb serial driver updates
- typec driver updates
- USB tracepoint additions
- dwc3 driver updates, including support for Apple hardware
- lots of other smaller driver updates and cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (161 commits)
usb: gadget: tegra-xudc: Always reinitialize data toggle when clear halt
USB: serial: option: move Telit 0x10c7 composition in the right place
USB: serial: option: add Telit Cinterion FE910C04 new compositions
usb: typec: ucsi: fix use-after-free caused by uec->work
usb: typec: ucsi: fix probe failure in gaokun_ucsi_probe()
usb: dwc3: core: Remove redundant comment in core init
usb: phy: Initialize struct usb_phy list_head
USB: serial: option: add Foxconn T99W760
usb: usb-storage: No additional quirks need to be added to the EL-R12 optical drive.
usb: typec: hd3ss3220: Enable VBUS based on ID pin state
dt-bindings: usb: ti,hd3ss3220: Add support for VBUS based on ID state
usb: typec: anx7411: add WQ_PERCPU to alloc_workqueue users
USB: add WQ_PERCPU to alloc_workqueue users
dt-bindings: usb: dwc3-xilinx: Describe the reset constraint for the versal platform
drivers/usb/storage: use min() instead of min_t()
usb: raw-gadget: cap raw_io transfer length to KMALLOC_MAX_SIZE
usb: ohci-da8xx: remove unused platform data
usb: gadget: functionfs: use dma_buf_unmap_attachment_unlocked() helper
usb: uas: reduce time under spinlock
usb: dwc3: eic7700: Add EIC7700 USB driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull persistent dentry infrastructure and conversion from Al Viro:
"Some filesystems use a kinda-sorta controlled dentry refcount leak to
pin dentries of created objects in dcache (and undo it when removing
those). A reference is grabbed and not released, but it's not actually
_stored_ anywhere.
That works, but it's hard to follow and verify; among other things, we
have no way to tell _which_ of the increments is intended to be an
unpaired one. Worse, on removal we need to decide whether the
reference had already been dropped, which can be non-trivial if that
removal is on umount and we need to figure out if this dentry is
pinned due to e.g. unlink() not done. Usually that is handled by using
kill_litter_super() as ->kill_sb(), but there are open-coded special
cases of the same (consider e.g. /proc/self).
Things get simpler if we introduce a new dentry flag
(DCACHE_PERSISTENT) marking those "leaked" dentries. Having it set
claims responsibility for +1 in refcount.
The end result this series is aiming for:
- get these unbalanced dget() and dput() replaced with new primitives
that would, in addition to adjusting refcount, set and clear
persistency flag.
- instead of having kill_litter_super() mess with removing the
remaining "leaked" references (e.g. for all tmpfs files that hadn't
been removed prior to umount), have the regular
shrink_dcache_for_umount() strip DCACHE_PERSISTENT of all dentries,
dropping the corresponding reference if it had been set. After that
kill_litter_super() becomes an equivalent of kill_anon_super().
Doing that in a single step is not feasible - it would affect too many
places in too many filesystems. It has to be split into a series.
This work has really started early in 2024; quite a few preliminary
pieces have already gone into mainline. This chunk is finally getting
to the meat of that stuff - infrastructure and most of the conversions
to it.
Some pieces are still sitting in the local branches, but the bulk of
that stuff is here"
* tag 'pull-persistency' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
d_make_discardable(): warn if given a non-persistent dentry
kill securityfs_recursive_remove()
convert securityfs
get rid of kill_litter_super()
convert rust_binderfs
convert nfsctl
convert rpc_pipefs
convert hypfs
hypfs: swich hypfs_create_u64() to returning int
hypfs: switch hypfs_create_str() to returning int
hypfs: don't pin dentries twice
convert gadgetfs
gadgetfs: switch to simple_remove_by_name()
convert functionfs
functionfs: switch to simple_remove_by_name()
functionfs: fix the open/removal races
functionfs: need to cancel ->reset_work in ->kill_sb()
functionfs: don't bother with ffs->ref in ffs_data_{opened,closed}()
functionfs: don't abuse ffs_data_closed() on fs shutdown
convert selinuxfs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
- Allow power-off for out-of-band wakeup-capable devices
- Drop the redundant call to dev_pm_domain_detach() for the amba bus
- Extend the genpd governor for CPUs to account for IPIs
pmdomain providers:
- bcm: Add support for BCM2712
- mediatek: Add support for MFlexGraphics power domains
- mediatek: Add support for MT8196 power domains
- qcom: Add RPMh power domain support for Kaanapali
- rockchip: Add support for RV1126B
pmdomain consumers:
- usb: dwc3: Enable out of band wakeup for i.MX95
- usb: chipidea: Enable out of band wakeup for i.MX95"
* tag 'pmdomain-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (26 commits)
pmdomain: Extend the genpd governor for CPUs to account for IPIs
smp: Introduce a helper function to check for pending IPIs
pmdomain: mediatek: convert from clk round_rate() to determine_rate()
amba: bus: Drop dev_pm_domain_detach() call
pmdomain: bcm: bcm2835-power: Prepare to support BCM2712
pmdomain: mediatek: mtk-mfg: select MAILBOX in Kconfig
pmdomain: mediatek: Add support for MFlexGraphics
pmdomain: mediatek: Fix build-errors
cpuidle: psci: Replace deprecated strcpy in psci_idle_init_cpu
pmdomain: rockchip: Add support for RV1126B
pmdomain: mediatek: Add support for MT8196 HFRPSYS power domains
pmdomain: mediatek: Add support for MT8196 SCPSYS power domains
pmdomain: mediatek: Add support for secure HWCCF infra power on
pmdomain: mediatek: Add support for Hardware Voter power domains
pmdomain: qcom: rpmhpd: Add RPMh power domain support for Kaanapali
usb: dwc3: imx8mp: Set out of band wakeup for i.MX95
usb: chipidea: ci_hdrc_imx: Set out of band wakeup for i.MX95
usb: chipidea: core: detach power domain for ci_hdrc platform device
pmdomain: core: Allow power-off for out-of-band wakeup-capable devices
PM: wakeup: Add out-of-band system wakeup support for devices
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are quite a few interesting things here, including new hardware
support, new features, some bug fixes and documentation updates. In
addition, there are a usual bunch of minor fixes and cleanups all
over.
In the new hardware support category, there are intel_pstate and
intel_rapl driver updates to support new processors, Panther Lake,
Wildcat Lake, Noval Lake, and Diamond Rapids in the OOB mode, OPP and
bandwidth allocation support in the tegra186 cpufreq driver, and
JH7110S SOC support in dt-platdev cpufreq.
The new features are the PM QoS CPU latency limit for suspend-to-idle,
the netlink support for the energy model management, support for
terminating system suspend via a wakeup event during the sync of file
systems, configurable number of hibernation compression threads, the
runtime PM auto-cleanup macros, and the "poweroff" PM event that is
expected to be used during system shutdown.
Bugs are mostly fixed in cpuidle governors, but there are also fixes
elsewhere, like in the amd-pstate cpufreq driver.
Documentation updates include, but are not limited to, a new doc on
debugging shutdown hangs, cross-referencing fixes and cleanups in the
intel_pstate documentation, and updates of comments in the core
hibernation code.
Specifics:
- Introduce and document a QoS limit on CPU exit latency during
wakeup from suspend-to-idle (Ulf Hansson)
- Add support for building libcpupower statically (Zuo An)
- Add support for sending netlink notifications to user space on
energy model updates (Changwoo Mini, Peng Fan)
- Minor improvements to the Rust OPP interface (Tamir Duberstein)
- Fixes to scope-based pointers in the OPP library (Viresh Kumar)
- Use residency threshold in polling state override decisions in the
menu cpuidle governor (Aboorva Devarajan)
- Add sanity check for exit latency and target residency in the
cpufreq core (Rafael Wysocki)
- Use this_cpu_ptr() where possible in the teo governor (Christian
Loehle)
- Rework the handling of tick wakeups in the teo cpuidle governor to
increase the likelihood of stopping the scheduler tick in the cases
when tick wakeups can be counted as non-timer ones (Rafael Wysocki)
- Fix a reverse condition in the teo cpuidle governor and drop a
misguided target residency check from it (Rafael Wysocki)
- Clean up multiple minor defects in the teo cpuidle governor (Rafael
Wysocki)
- Update header inclusion to make it follow the Include What You Use
principle (Andy Shevchenko)
- Enable MSR-based RAPL PMU support in the intel_rapl power capping
driver and arrange for using it on the Panther Lake and Wildcat
Lake processors (Kuppuswamy Sathyanarayanan)
- Add support for Nova Lake and Wildcat Lake processors to the
intel_rapl power capping driver (Kaushlendra Kumar, Srinivas
Pandruvada)
- Add OPP and bandwidth support for Tegra186 (Aaron Kling)
- Optimizations for parameter array handling in the amd-pstate
cpufreq driver (Mario Limonciello)
- Fix for mode changes with offline CPUs in the amd-pstate cpufreq
driver (Gautham Shenoy)
- Preserve freq_table_sorted across suspend/hibernate in the cpufreq
core (Zihuan Zhang)
- Adjust energy model rules for Intel hybrid platforms in the
intel_pstate cpufreq driver and improve printing of debug messages
in it (Rafael Wysocki)
- Replace deprecated strcpy() in cpufreq_unregister_governor()
(Thorsten Blum)
- Fix duplicate hyperlink target errors in the intel_pstate cpufreq
driver documentation and use :ref: directive for internal linking
in it (Swaraj Gaikwad, Bagas Sanjaya)
- Add Diamond Rapids OOB mode support to the intel_pstate cpufreq
driver (Kuppuswamy Sathyanarayanan)
- Use mutex guard for driver locking in the intel_pstate driver and
eliminate some code duplication from it (Rafael Wysocki)
- Replace udelay() with usleep_range() in ACPI cpufreq (Kaushlendra
Kumar)
- Minor improvements to various cpufreq drivers (Christian Marangi,
Hal Feng, Jie Zhan, Marco Crivellari, Miaoqian Lin, and Shuhao Fu)
- Replace snprintf() with scnprintf() in show_trace_dev_match()
(Kaushlendra Kumar)
- Fix memory allocation error handling in pm_vt_switch_required()
(Malaya Kumar Rout)
- Introduce CALL_PM_OP() macro and use it to simplify code in generic
PM operations (Kaushlendra Kumar)
- Add module param to backtrace all CPUs in the device power
management watchdog (Sergey Senozhatsky)
- Rework message printing in swsusp_save() (Rafael Wysocki)
- Make it possible to change the number of hibernation compression
threads (Xueqin Luo)
- Clarify that only cgroup1 freezer uses PM freezer (Tejun Heo)
- Add document on debugging shutdown hangs to PM documentation and
correct a mistaken configuration option in it (Mario Limonciello)
- Shut down wakeup source timer before removing the wakeup source
from the list (Kaushlendra Kumar, Rafael Wysocki)
- Introduce new PMSG_POWEROFF event for system shutdown handling with
the help of PM device callbacks (Mario Limonciello)
- Make pm_test delay interruptible by wakeup events (Riwen Lu)
- Clean up kernel-doc comment style usage in the core hibernation
code and remove unuseful comments from it (Sunday Adelodun, Rafael
Wysocki)
- Add support for handling wakeup events and aborting the suspend
process while it is syncing file systems (Samuel Wu, Rafael
Wysocki)
- Add WQ_UNBOUND to pm_wq workqueue (Marco Crivellari)
- Add runtime PM wrapper macros for ACQUIRE()/ACQUIRE_ERR() and use
them in the PCI core and the ACPI TAD driver (Rafael Wysocki)
- Improve runtime PM in the ACPI TAD driver (Rafael Wysocki)
- Update pm_runtime_allow/forbid() documentation (Rafael Wysocki)
- Fix typos in runtime.c comments (Malaya Kumar Rout)
- Move governor.h from devfreq under include/linux/ and rename to
devfreq-governor.h to allow devfreq governor definitions in out of
drivers/devfreq/ (Dmitry Baryshkov)
- Use min() to improve readability in tegra30-devfreq.c (Thorsten
Blum)
- Fix potential use-after-free issue of OPP handling in
hisi_uncore_freq.c (Pengjie Zhang)
- Fix typo in DFSO_DOWNDIFFERENTIAL macro name in
governor_simpleondemand.c in devfreq (Riwen Lu)"
* tag 'pm-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (96 commits)
PM / devfreq: Fix typo in DFSO_DOWNDIFFERENTIAL macro name
cpuidle: Warn instead of bailing out if target residency check fails
cpuidle: Update header inclusion
Documentation: power/cpuidle: Document the CPU system wakeup latency QoS
cpuidle: Respect the CPU system wakeup QoS limit for cpuidle
sched: idle: Respect the CPU system wakeup QoS limit for s2idle
pmdomain: Respect the CPU system wakeup QoS limit for cpuidle
pmdomain: Respect the CPU system wakeup QoS limit for s2idle
PM: QoS: Introduce a CPU system wakeup QoS limit
cpuidle: governors: teo: Add missing space to the description
PM: hibernate: Extra cleanup of comments in swap handling code
PM / devfreq: tegra30: use min to simplify actmon_cpu_to_emc_rate
PM / devfreq: hisi: Fix potential UAF in OPP handling
PM / devfreq: Move governor.h to a public header location
powercap: intel_rapl: Enable MSR-based RAPL PMU support
powercap: intel_rapl: Prepare read_raw() interface for atomic-context callers
cpufreq: qcom-nvmem: fix compilation warning for qcom_cpufreq_ipq806x_match_list
PM: sleep: Call pm_sleep_fs_sync() instead of ksys_sync_helper()
PM: sleep: Add support for wakeup during filesystem sync
cpufreq: ACPI: Replace udelay() with usleep_range()
...
|
|
The driver previously skipped handling ClearFeature(ENDPOINT_HALT)
when the endpoint was already not halted. This prevented the
controller from resetting the data sequence number and reinitializing
the endpoint state.
According to USB 3.2 specification Rev. 1.1, section 9.4.5,
ClearFeature(ENDPOINT_HALT) must always reset the data sequence and
set the stream state machine to Disabled, regardless of whether the
endpoint was halted.
Remove the early return so that ClearFeature(ENDPOINT_HALT) always
resets the endpoint sequence state as required by the specification.
Fixes: 49db427232fe ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable <stable@kernel.org>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://patch.msgid.link/20251127033540.2287517-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB serial updates for 6.19-rc1
Here are the USB serial updates for 6.19-rc1:
- fix belkin_sa and kobil_sct TIOCMBIS and TIOCMBIC ioctls
- match on interface number for dual-port ftdi devices with reserved
jtag port
- do not log reserved ftdi jtag ports on probe
- apply ftdi_sio NDI quirk remapping 19200 bps consistently
- drop ftdi_sio NDI quirk module parameter
- clean up ftdi_sio quirk implementations
- add more modem device ids
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.19-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: move Telit 0x10c7 composition in the right place
USB: serial: option: add Telit Cinterion FE910C04 new compositions
USB: serial: option: add Foxconn T99W760
USB: serial: ftdi_sio: drop NDI quirk module parameter
USB: serial: ftdi_sio: clean up NDI speed hack
USB: serial: ftdi_sio: enable NDI speed hack consistently
USB: serial: ftdi_sio: rename quirk symbols
USB: serial: ftdi_sio: clean up quirk comments
USB: serial: ftdi_sio: rewrite 8u2232c quirk
USB: serial: ftdi_sio: silence jtag probe
USB: serial: ftdi_sio: match on interface number for jtag
USB: serial: kobil_sct: drop unnecessary initialisations
USB: serial: kobil_sct: clean up set_termios()
USB: serial: kobil_sct: add control request helpers
USB: serial: kobil_sct: clean up device type checks
USB: serial: kobil_sct: clean up tiocmset()
USB: serial: belkin_sa: clean up tiocmset()
USB: serial: kobil_sct: fix TIOCMBIS and TIOCMBIC
USB: serial: belkin_sa: fix TIOCMBIS and TIOCMBIC
|
|
Move Telit 0x10c7 composition right after 0x10c6 composition and
before 0x10c8 composition.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add the following Telit Cinterion new compositions:
0x10c1: RNDIS + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c1 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c2: MBIM + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c2 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c3: ECM + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c3 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c5: RNDIS + tty (AT) + tty (AT) + tty (diag)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c5 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c6: MBIM + tty (AT) + tty (AT) + tty (diag)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c6 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c9: MBIM + tty (AT) + tty (diag) + DPL (Data Packet Logging) + adb
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c9 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10cb: RNDIS + tty (AT) + tty (diag) + DPL (Data Packet Logging) + adb
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10cb Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The delayed work uec->work is scheduled in gaokun_ucsi_probe()
but never properly canceled in gaokun_ucsi_remove(). This creates
use-after-free scenarios where the ucsi and gaokun_ucsi structure
are freed after ucsi_destroy() completes execution, while the
gaokun_ucsi_register_worker() might be either currently executing
or still pending in the work queue. The already-freed gaokun_ucsi
or ucsi structure may then be accessed.
Furthermore, the race window is 3 seconds, which is sufficiently
long to make this bug easily reproducible. The following is the
trace captured by KASAN:
==================================================================
BUG: KASAN: slab-use-after-free in __run_timers+0x5ec/0x630
Write of size 8 at addr ffff00000ec28cc8 by task swapper/0/0
...
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x78/0x90
print_report+0x114/0x580
kasan_report+0xa4/0xf0
__asan_report_store8_noabort+0x20/0x2c
__run_timers+0x5ec/0x630
run_timer_softirq+0xe8/0x1cc
handle_softirqs+0x294/0x720
__do_softirq+0x14/0x20
____do_softirq+0x10/0x1c
call_on_irq_stack+0x30/0x48
do_softirq_own_stack+0x1c/0x28
__irq_exit_rcu+0x27c/0x364
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x40/0x60
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
arch_local_irq_enable+0x4/0x8 (P)
do_idle+0x334/0x458
cpu_startup_entry+0x60/0x70
rest_init+0x158/0x174
start_kernel+0x2f8/0x394
__primary_switched+0x8c/0x94
Allocated by task 72 on cpu 0 at 27.510341s:
kasan_save_stack+0x2c/0x54
kasan_save_track+0x24/0x5c
kasan_save_alloc_info+0x40/0x54
__kasan_kmalloc+0xa0/0xb8
__kmalloc_node_track_caller_noprof+0x1c0/0x588
devm_kmalloc+0x7c/0x1c8
gaokun_ucsi_probe+0xa0/0x840 auxiliary_bus_probe+0x94/0xf8
really_probe+0x17c/0x5b8
__driver_probe_device+0x158/0x2c4
driver_probe_device+0x10c/0x264
__device_attach_driver+0x168/0x2d0
bus_for_each_drv+0x100/0x188
__device_attach+0x174/0x368
device_initial_probe+0x14/0x20
bus_probe_device+0x120/0x150
device_add+0xb3c/0x10fc
__auxiliary_device_add+0x88/0x130
...
Freed by task 73 on cpu 1 at 28.910627s:
kasan_save_stack+0x2c/0x54
kasan_save_track+0x24/0x5c
__kasan_save_free_info+0x4c/0x74
__kasan_slab_free+0x60/0x8c
kfree+0xd4/0x410
devres_release_all+0x140/0x1f0
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x344/0x460
device_release_driver+0x18/0x24
bus_remove_device+0x198/0x274
device_del+0x310/0xa84
...
The buggy address belongs to the object at ffff00000ec28c00
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 200 bytes inside of
freed 512-byte region
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x4ec28
head: order:2 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x3fffe0000000040(head|node=0|zone=0|lastcpupid=0x1ffff)
page_type: f5(slab)
raw: 03fffe0000000040 ffff000008801c80 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 03fffe0000000040 ffff000008801c80 dead000000000122 0000000000000000
head: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 03fffe0000000002 fffffdffc03b0a01 00000000ffffffff 00000000ffffffff
head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000004
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00000ec28b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff00000ec28c00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff00000ec28c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff00000ec28d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff00000ec28d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Add disable_delayed_work_sync() in gaokun_ucsi_remove() to ensure
that uec->work is properly canceled and prevented from executing
after the ucsi and gaokun_ucsi structure have been deallocated.
Fixes: 00327d7f2c8c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/cc31e12ef9ffbf86676585b02233165fd33f0d8e.1764065838.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The gaokun_ucsi_probe() uses ucsi_create() to allocate a UCSI instance.
The ucsi_create() validates whether ops->poll_cci is defined, and if not,
it directly returns -EINVAL. However, the gaokun_ucsi_ops structure does
not define the poll_cci, causing ucsi_create() always fail with -EINVAL.
This issue can be observed in the kernel log with the following error:
ucsi_huawei_gaokun.ucsi huawei_gaokun_ec.ucsi.0: probe with driver
ucsi_huawei_gaokun.ucsi failed with error -22
Fix the issue by adding the missing poll_cci callback to gaokun_ucsi_ops.
Fixes: 00327d7f2c8c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Pengyu Luo <mitltlatltl@gmail.com>
Link: https://patch.msgid.link/4d077d6439d728be68646bb8c8678436a3a0885e.1764065838.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove redundant comment which was put in to address LLUCTL register
modifications for all applicable ports of multiport controller. Although
the support was added, the todo comment wasn't removed then.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20251116123033.131004-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
