| Age | Commit message (Collapse) | Author |
|---|
|
kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 *
KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that
skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can
deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or
leave a short trailing remainder on a later loop iteration. Either case
underflows usb_packet_length to about 65530.
That bypasses the usb_packet_length < ether_packet_length truncation path.
The device-supplied ether_packet_length, a le16 up to 65535 read from
header_start[2], then drives a memcmp() and the following skb_trim() and
skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10,
which is 14000 bytes. That is an out of bounds read.
Require both the start and end framing headers to be present before
subtracting them, on every loop iteration.
Fixes: d40261236e8e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/178211531778.2216480.12637613349790980750@maoyixie.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Configured VLANs intermittently stop receiving traffic after a link
down/up cycle, e.g. when the network cable is unplugged and plugged back
in. VLAN filtering stays enabled but all VLAN-tagged frames are dropped
until a VLAN is added or removed again.
The LAN7801 datasheet (DS00002123E) states:
"A portion of the MAC operates on clocks generated by the Ethernet
PHY. During a PHY reset event, this portion of the MAC is designed to
not be taken out of reset until the PHY clocks are operational"
(section 8.10, MAC Reset Watchdog Timer)
"After a reset event, the RFE will automatically initialize the
contents of the VHF to 0h."
(section 7.1.4, VHF Organization)
Thus a link down/up cycle stops and restarts the PHY clock, resets the
PHY-clocked portion of the MAC, and the RFE clears its VLAN/DA hash
filter (VHF) memory. The VHF holds both the VLAN filter table and the
multicast hash table, but the driver never reprograms either from its
shadow copy once the link is back, so both stay empty.
Reprogram the VLAN filter and multicast hash tables on link up.
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Closes: https://lore.kernel.org/netdev/BEZP281MB224501E38B30BFDC4BD3D364D9E32@BEZP281MB2245.DEUP281.PROD.OUTLOOK.COM/T/#u
Tested-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260622102911.484045-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.1-rc8).
Conflicts:
drivers/net/ethernet/wangxun/txgbe/txgbe_aml.c
f67aead16e85 ("net: txgbe: rework service event handling")
57d39faed4c9 ("net: txgbe: improve functions of AML 40G devices")
net/rds/info.c
512db8267b73 ("rds: mark snapshot pages dirty in rds_info_getsockopt()")
6e94eeb2a2a6 ("rds: convert to getsockopt_iter")
Adjacent changes:
include/net/sock.h
1ee90b77b727 ("net: guard timestamp cmsgs to real error queue skbs")
f0de88303d5e ("net: make is_skb_wmem() available to modules")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If usb_reset_device() returns a negative error code, stop the
process of probing.
Fixes: 10c3271712f5 ("r8152: disable the ECM mode")
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260604092247.27158-450-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Enable autosuspend support for Telit Cinterion LE310X1 RNDIS interface
by selecting a driver_info variant with manage_power callback.
This keeps power management scoped to the new Telit ID only, and avoids
changing behavior for all existing RNDIS devices.
Signed-off-by: Shaoxu Liu <shaoxul@foxmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/tencent_B7686B84CD4B76D76BB912FA6367FAC2CA05@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a device match entry for Telit Cinterion LE310X1 RNDIS interface
(VID:PID 1bc7:7030).
This is a functional no-op and keeps using the generic rndis_info for now.
Power-management behavior is handled in a follow-up patch.
Signed-off-by: Shaoxu Liu <shaoxul@foxmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/tencent_F1AF1F5AD39C56485BD16C6DB2415E5B9508@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the Qualcomm Technology Snapdragon X35-based MeiG SRM813Q
module.
The module can be put in different modes via AT commands
to enable/disable GPS functionality:
MODEM - PPP mode(2dee:4d63): AT+SER=1,1
If#= 0: RMNET
If#= 1: DIAG/ADB
If#= 2: MODEM
If#= 3: AT
P: Vendor=2dee ProdID=4d63 Rev=05.15
S: Manufacturer=MEIG
S: Product=LTE-A Module
S: SerialNumber=1bd51f0e
C: #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
NMEA mode(2dee:4d64): AT+SER=51,1
If#= 0: RMNET
If#= 1: DIAG/ADB
If#= 2: NMEA
If#= 3: AT
P: Vendor=2dee ProdID=4d64 Rev=05.15
S: Manufacturer=MEIG
S: Product=LTE-A Module
S: SerialNumber=1bd51f0e
C: #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
Signed-off-by: Jan Volckaert <janvolck@gmail.com>
Link: https://patch.msgid.link/20260517153237.55995-2-janvolck@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have macros to retrieve endpoint numbers now.
Use them.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260513132916.39896-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
simple_strtoul() is deprecated as it has no error checking. Replace it
with kstrtouint() which returns an error code on invalid input, and add
appropriate error handling.
Also add a NULL check before parsing flags, since strsep() can set id
to NULL if the input has fewer tokens than expected.
Preserve the original behavior for a trailing colon by checking *id
before parsing flags, so an empty string results in flags = 0 rather
than an error.
Signed-off-by: Sajal Gupta <sajal2005gupta@gmail.com>
Link: https://patch.msgid.link/20260509095518.2640-1-sajal2005gupta@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.1-rc3).
Conflicts:
net/ipv4/igmp.c
726fa7da2d8c ("ipv4: igmp: get rid of IGMPV3_{QQIC,MRC} and simplify calculation")
c6bebaa744f7 ("ipv4: igmp: annotate data-races in igmp_heard_query()")
https://lore.kernel.org/a7365e4873340f7a5e30411207de3bf9@kernel.org
Adjacent changes:
net/psp/psp_main.c
30cb24f97d44 ("psp: strip variable-length PSP header in psp_dev_rcv()")
c2b22277ad89 ("psp: validate IPv4 header fields in psp_dev_rcv()")
net/sched/sch_fq_codel.c
f83e07b29246 ("net/sched: sch_fq_codel: annotate data-races from fq_codel_dump_class_stats()")
3f3aa77ff1c8 ("net/sched: add qstats_cpu_drop_inc() helper")
net/wireless/pmsr.c
0f3c0a197309 ("wifi: nl80211: fix NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST usage")
410aa47fd9d3 ("wifi: cfg80211: allow suppressing FTM result reporting for PD requests")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8159 (RTL_VER_17) requires firmware for its PHY in order to work
at connection speeds > 5GBit. Add support for uploading firmware for
the PHY using the existing rtl8152_apply_firmware() function
in r8157_hw_phy_cfg() and set up the correct names for the firmware
files.
This also adds support for uploading firmware for the RTL8157
(RTL_VER_16) PHY, for which firmware is however not strictly necessary
to work. Still, this allows to upload newer versions of the firmware used
by this chip, e.g. to improve interoperability.
If no firmware is found, both the RTL8157 and the RTL8159 will continue
to work.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20260505-rtl8159_net_next-v4-3-1a648a9c4d8d@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8159 re-uses the packet descriptor format introduced with the
RTL8157 and other hardware features of the RTL8157 (RTL_VER_16) such
as the SRAM access. The support therefore consists in expanding the
existing RTL8157 code for initialization and USB power management
to also be used for the RTL8159 (RTL_VER_17).
Most of the additional code is added in r8157_hw_phy_cfg() to configure
the RTL8159 PHY.
Add support for the USB device ID of Realtek RTL8159-based adapters,
for which the product ID is 0x815a. Detect the RTL8159 as RTL_VER_17
and set it up.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20260505-rtl8159_net_next-v4-2-1a648a9c4d8d@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8159 supports 10GBit Link speeds. Add support for this speed
in the setup and setting/getting through ethtool. Also add 10GBit EEE.
Add functionality for setup and ethtool get/set methods.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20260505-rtl8159_net_next-v4-1-1a648a9c4d8d@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit e0bffe3e6894 ("net: asix: ax88772: migrate to phylink") replaced
the asix_adjust_link() PHY callback with phylink's mac_link_up() and
mac_link_down() handlers, but did not carry over the usbnet_link_change()
notification that commit 805206e66fab ("net: asix: fix "can't send until
first packet is send" issue") had added.
As a result, the original symptom returns: when the link comes up,
usbnet is never notified, so the RX URB submission stays dormant until
some other event (e.g. a transmitted packet triggering the status
endpoint interrupt) wakes it up.
This is reproducible with the Apple A1277 USB Ethernet Adapter
(05ac:1402, AX88772A based) on a Banana Pro using a static IPv4
configuration. After bringing the interface up, no incoming packets are
received until the first outgoing frame triggers usbnet's RX path.
Restore the link change notification, gated on a carrier transition so
the call remains idempotent if the status endpoint also reports the
change later.
Fixes: e0bffe3e6894 ("net: asix: ax88772: migrate to phylink")
Signed-off-by: Markus Baier <Markus.Baier@soslab.tu-darmstadt.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260501163941.107668-1-Markus.Baier@soslab.tu-darmstadt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Apple Silicon Macs expose two CDC NCM "private" data interfaces over
USB-C with VID:PID 0x05ac:0x1905 and product string "Mac". This is the
same protocol Apple already ships on iPhone (0x05ac:0x12a8) and iPad
(0x05ac:0x12ab) for RemoteXPC since iOS 17 -- both data interfaces lack
an interrupt status endpoint, so they rely on the FLAG_LINK_INTR-
conditional bind path introduced in commit 3ec8d7572a69 ("CDC-NCM: add
support for Apple's private interface").
The id_table currently has entries for iPhone and iPad but not for the
Mac. Without a match, cdc_ncm falls through to the generic CDC NCM
class-match entry, which uses the FLAG_LINK_INTR-having cdc_ncm_info
struct, so bind_common() fails on the missing status endpoint and no
netdev appears.
Add id_table entries for both interface numbers (0 and 2) of the Mac,
bound to the existing apple_private_interface_info driver_info.
Verified empirically on a Mac Studio M3 Ultra running macOS 26.5: when
a Mac is connected via USB-C, ioreg shows VID 0x05ac, PID 0x1905,
product string "Mac", with two NCM data interfaces at numbers 0 and 2.
The same PID is presented by all current Apple Silicon Mac models
(MacBook Pro/Air, Mac mini, Mac Studio across the M-series), mirroring
Apple's single-PID-per-family pattern from iPhone/iPad.
After this patch, plugging a Mac into a Linux host running the patched
kernel produces two enx... interfaces (one per data interface),
"ip -br link" lists them as UP, and standard userspace networking
(DHCP, NetworkManager shared mode, etc.) works without any modprobe
overrides or out-of-tree modules.
Signed-off-by: Alex Cheema <alex@exolabs.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260429175739.34426-1-alex@exolabs.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The TRENDnet TUC-ET2G V2.0 is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260430213435.21821-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.1-rc2).
No conflicts, or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace explicit testing of bits and clearing these bits by existing
functions ocp_word_test_and_clr_bits() and r8152_mdio_test_and_clr_bit()
to re-use this code.
This allows to remove the "ocp_data" variable. Also remove the "ret" variable
which was incorrectly used for the r8153_phy_status() return value which
is a u16, so that the remaining "data" variable is sufficient.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260428-use_bit_functions-v1-1-6eb5a3507610@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to a Copy & Paste Error, the PLA_MCU_SPDWN_EN bit was cleared
twice consecutively using ocp_word_clr_bits. Fix that.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260428-patch_double-v1-1-27c830a9eb2e@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When rtl8150_start_xmit() fails to submit the tx URB, the URB is never
handed to the USB core and write_bulk_callback() will not run. The
driver returns NETDEV_TX_OK, which tells the networking stack that the
skb has been consumed, but nothing actually frees the skb on this
error path:
dev->tx_skb = skb;
...
if ((res = usb_submit_urb(dev->tx_urb, GFP_ATOMIC))) {
...
/* no kfree_skb here */
}
return NETDEV_TX_OK;
This leaks the skb on every submit failure and also leaves dev->tx_skb
pointing at memory that the driver itself may later free, which is
fragile.
Free the skb with dev_kfree_skb_any() in the error path and clear
dev->tx_skb so no stale pointer is left behind.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Morduan Zang <zhangdandan@uniontech.com>
Link: https://patch.msgid.link/E7D3E1C013C5A859+20260424015517.9574-1-zhangdandan@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported a KASAN slab-use-after-free read in rtl8150_start_xmit()
when accessing skb->len for tx statistics after usb_submit_urb() has
been called:
BUG: KASAN: slab-use-after-free in rtl8150_start_xmit+0x71f/0x760
drivers/net/usb/rtl8150.c:712
Read of size 4 at addr ffff88810eb7a930 by task kworker/0:4/5226
The URB completion handler write_bulk_callback() frees the skb via
dev_kfree_skb_irq(dev->tx_skb). The URB may complete on another CPU
in softirq context before usb_submit_urb() returns in the submitter,
so by the time the submitter reads skb->len the skb has already been
queued to the per-CPU completion_queue and freed by net_tx_action():
CPU A (xmit) CPU B (USB completion softirq)
------------ ------------------------------
dev->tx_skb = skb;
usb_submit_urb() --+
|-------> write_bulk_callback()
| dev_kfree_skb_irq(dev->tx_skb)
| net_tx_action()
| napi_skb_cache_put() <-- free
netdev->stats.tx_bytes |
+= skb->len; <-- UAF read
Fix it by caching skb->len before submitting the URB and using the
cached value when updating the tx_bytes counter.
The pre-existing tx_bytes semantics are preserved: the counter tracks
the original frame length (skb->len), not the ETH_ZLEN/USB-alignment
padded "count" value that is handed to the device. Changing that
would be a user-visible accounting change and is out of scope for
this UAF fix.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+3f46c095ac0ca048cb71@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/69e69ee7.050a0220.24bfd3.002b.GAE@google.com/
Closes: https://syzkaller.appspot.com/bug?extid=3f46c095ac0ca048cb71
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhan Jun <zhanjun@uniontech.com>
Link: https://patch.msgid.link/809895186B866C10+20260423004913.136655-1-zhangdandan@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes in preparation for the net-next PR.
Conflicts:
include/net/sch_generic.h
a6bd339dbb351 ("net_sched: fix skb memory leak in deferred qdisc drops")
ff2998f29f390 ("net: sched: introduce qdisc-specific drop reason tracing")
https://lore.kernel.org/adz0iX85FHMz0HdO@sirena.org.uk
drivers/net/ethernet/airoha/airoha_eth.c
1acdfbdb516b ("net: airoha: Fix VIP configuration for AN7583 SoC")
bf3471e6e6c0 ("net: airoha: Make flow control source port mapping dependent on nbq parameter")
Adjacent changes:
drivers/net/ethernet/airoha/airoha_ppe.c
f44218cd5e6a ("net: airoha: Reset PPE cpu port configuration in airoha_ppe_hw_init()")
7da62262ec96 ("inet: add ip_local_port_step_width sysctl to improve port usage distribution")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A malicious USB device claiming to be a CDC Phonet modem can overflow
the skb_shared_info->frags[] array by sending an unbounded sequence of
full-page bulk transfers.
Drop the skb and increment the length error when the frag limit is
reached. This matches the same fix that commit f0813bcd2d9d ("net:
wwan: t7xx: fix potential skb->frags overflow in RX path") did for the
t7xx driver.
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: stable <stable@kernel.org>
Assisted-by: gregkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026041134-dreamboat-buddhism-d1ec@gregkh
Fixes: 87cf65601e17 ("USB host CDC Phonet network interface driver")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The RTL8157 uses a different packet descriptor format compared to the
previous generation of chips. Add support for this format by adding a
descriptor format structure into the r8152 structure and corresponding
desc_ops functions which abstract the vlan-tag, tx/rx len and
tx/rx checksum algorithms.
Also, add support for the ADV indirect access interface of the RTL8157
and PHY setup.
For initialization of the RTL8157, combine the existing RTL8156B and
RTL8156 init functions and add RTL8157-specific functinality in order
to improve code readability and maintainability.
r8156_init() is now called with RTL_VER_10 and RTL_VER_11 for the RTL8156,
with RTL_VER_12, RTL_VER_13 and RTL_VER_15 for the RTL8156B and with
RTL_VER_16 for the RTL8157 and checks the version for chip-specific code.
Also add USB power control functions for the RTL8157.
Add support for the USB device ID of Realtek RTL8157-based adapters. Detect
the RTL8157 as RTL_VER_16 and set it up.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260404-rtl8157_next-v7-2-039121318f23@birger-koblitz.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The RTL8157 supports 5GBit Link speeds. Add support for this speed
in the setup and setting/getting through ethtool. Also add 5GBit EEE.
Add functionality for setup and ethtool get/set methods.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260404-rtl8157_next-v7-1-039121318f23@birger-koblitz.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the following helper functions for SRAM2 access to simplify the code
and improve readability:
- sram2_write() - write data to SRAM2 address
- sram2_read() - read data from SRAM2 address
- sram2_write_w0w1() - read-modify-write operation
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260401115542.34601-1-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260330102611.1671546-3-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the common USB helpers for looking up bulk and interrupt endpoints
instead of a custom implementation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260330102611.1671546-2-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following bitwise operation functions for PHY OCP registers to
simplify the code.
- ocp_reg_w0w1()
- ocp_reg_clr_bits()
- ocp_reg_set_bits()
- sram_write_w0w1()
- sram_clr_bits()
- sram_set_bits()
- r8152_mdio_clr_bit()
- r8152_mdio_set_bit()
- r8152_mdio_test_and_clr_bit()
In addition, remove variable set but not used from r8153_init(),
r8153b_init() and r8153c_init().
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260326073925.32976-456-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the following bitwise operation functions for PLA/USB OCP registers
to simplify the code.
- ocp_dword_w0w1()
- ocp_word_w0w1()
- ocp_byte_w0w1()
- ocp_dword_clr_bits()
- ocp_dword_set_bits()
- ocp_word_clr_bits()
- ocp_word_set_bits()
- ocp_word_test_and_clr_bits()
- ocp_byte_clr_bits()
- ocp_byte_set_bits()
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260326073925.32976-455-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The old code used ocp_write_byte() to clear the OOBS_POLLING bit
(BIT(8)) in the USB_UPHY_XTAL register, but this doesn't correctly
clear a bit in the upper byte of the 16-bit register.
Fix this by using ocp_write_word() instead.
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260326073925.32976-454-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As IPv6 is built-in only, the ipv6_stub infrastructure is no longer
necessary.
Convert all drivers currently utilizing ipv6_stub to make direct
function calls. The fallback functions introduced previously will
prevent linkage errors when CONFIG_IPV6 is disabled.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Tested-by: Ricardo B. Marlière <rbm@suse.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Antonio Quartulli <antonio@openvpn.net>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20260325120928.15848-7-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.0-rc5).
net/netfilter/nft_set_rbtree.c
598adea720b97 ("netfilter: revert nft_set_rbtree: validate open interval overlap")
3aea466a43998 ("netfilter: nft_set_rbtree: don't disable bh when acquiring tree lock")
https://lore.kernel.org/abgaQBpeGstdN4oq@sirena.org.uk
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reports "task hung in rpm_resume"
This is caused by aqc111_suspend calling
the PM variant of its write_cmd routine.
The simplified call trace looks like this:
rpm_suspend()
usb_suspend_both() - here udev->dev.power.runtime_status == RPM_SUSPENDING
aqc111_suspend() - called for the usb device interface
aqc111_write32_cmd()
usb_autopm_get_interface()
pm_runtime_resume_and_get()
rpm_resume() - here we call rpm_resume() on our parent
rpm_resume() - Here we wait for a status change that will never happen.
At this point we block another task which holds
rtnl_lock and locks up the whole networking stack.
Fix this by replacing the write_cmd calls with their _nopm variants
Reported-by: syzbot+48dc1e8dfc92faf1124c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=48dc1e8dfc92faf1124c
Fixes: e58ba4544c77 ("net: usb: aqc111: Add support for wake on LAN by MAGIC packet")
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Link: https://patch.msgid.link/20260313141643.1181386-1-zlatistiv@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The same bounds-check bug fixed for NDP16 in the previous patch also
exists in cdc_ncm_rx_verify_ndp32(). The DPE array size is validated
against the total skb length without accounting for ndpoffset, allowing
out-of-bounds reads when the NDP32 is placed near the end of the NTB.
Add ndpoffset to the nframes bounds check and use struct_size_t() to
express the NDP-plus-DPE-array size more clearly.
Compile-tested only.
Fixes: 0fa81b304a79 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block")
Signed-off-by: Tobi Gaertner <tob.gaertner@me.com>
Link: https://patch.msgid.link/20260314054640.2895026-3-tob.gaertner@me.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
cdc_ncm_rx_verify_ndp16() validates that the NDP header and its DPE
entries fit within the skb. The first check correctly accounts for
ndpoffset:
if ((ndpoffset + sizeof(struct usb_cdc_ncm_ndp16)) > skb_in->len)
but the second check omits it:
if ((sizeof(struct usb_cdc_ncm_ndp16) +
ret * (sizeof(struct usb_cdc_ncm_dpe16))) > skb_in->len)
This validates the DPE array size against the total skb length as if
the NDP were at offset 0, rather than at ndpoffset. When the NDP is
placed near the end of the NTB (large wNdpIndex), the DPE entries can
extend past the skb data buffer even though the check passes.
cdc_ncm_rx_fixup() then reads out-of-bounds memory when iterating
the DPE array.
Add ndpoffset to the nframes bounds check and use struct_size_t() to
express the NDP-plus-DPE-array size more clearly.
Fixes: ff06ab13a4cc ("net: cdc_ncm: splitting rx_fixup for code reuse")
Signed-off-by: Tobi Gaertner <tob.gaertner@me.com>
Link: https://patch.msgid.link/20260314054640.2895026-2-tob.gaertner@me.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
usbnet_generic_cdc_bind() is duplicating the error handling
multiple times. That is bad. Unify it with jumps.
V2: Update error logging with every cause a unique message
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260312084612.1469853-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.0-rc4).
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c
db25c42c2e1f9 ("net/mlx5e: RX, Fix XDP multi-buf frag counting for striding RQ")
dff1c3164a692 ("net/mlx5e: SHAMPO, Always calculate page size")
https://lore.kernel.org/aa7ORohmf67EKihj@sirena.org.uk
drivers/net/ethernet/ti/am65-cpsw-nuss.c
840c9d13cb1ca ("net: ethernet: ti: am65-cpsw-nuss: Fix rx_filter value for PTP support")
a23c657e332f2 ("net: ethernet: ti: am65-cpsw: Use also port number to identify timestamps")
https://lore.kernel.org/abK3EkIXuVgMyGI7@sirena.org.uk
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove redundant netif_napi_del() call from disconnect path.
A WARN may be triggered in __netif_napi_del_locked() during USB device
disconnect:
WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350
This happens because netif_napi_del() is called in the disconnect path while
NAPI is still enabled. However, it is not necessary to call netif_napi_del()
explicitly, since unregister_netdev() will handle NAPI teardown automatically
and safely. Removing the redundant call avoids triggering the warning.
Full trace:
lan78xx 1-1:1.0 enu1: Failed to read register index 0x000000c4. ret = -ENODEV
lan78xx 1-1:1.0 enu1: Failed to set MAC down with error -ENODEV
lan78xx 1-1:1.0 enu1: Link is Down
lan78xx 1-1:1.0 enu1: Failed to read register index 0x00000120. ret = -ENODEV
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350
Modules linked in: flexcan can_dev fuse
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.0-rc2-00624-ge926949dab03 #9 PREEMPT
Hardware name: SKOV IMX8MP CPU revC - bd500 (DT)
Workqueue: usb_hub_wq hub_event
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __netif_napi_del_locked+0x2b4/0x350
lr : __netif_napi_del_locked+0x7c/0x350
sp : ffffffc085b673c0
x29: ffffffc085b673c0 x28: ffffff800b7f2000 x27: ffffff800b7f20d8
x26: ffffff80110bcf58 x25: ffffff80110bd978 x24: 1ffffff0022179eb
x23: ffffff80110bc000 x22: ffffff800b7f5000 x21: ffffff80110bc000
x20: ffffff80110bcf38 x19: ffffff80110bcf28 x18: dfffffc000000000
x17: ffffffc081578940 x16: ffffffc08284cee0 x15: 0000000000000028
x14: 0000000000000006 x13: 0000000000040000 x12: ffffffb0022179e8
x11: 1ffffff0022179e7 x10: ffffffb0022179e7 x9 : dfffffc000000000
x8 : 0000004ffdde8619 x7 : ffffff80110bcf3f x6 : 0000000000000001
x5 : ffffff80110bcf38 x4 : ffffff80110bcf38 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 1ffffff0022179e7 x0 : 0000000000000000
Call trace:
__netif_napi_del_locked+0x2b4/0x350 (P)
lan78xx_disconnect+0xf4/0x360
usb_unbind_interface+0x158/0x718
device_remove+0x100/0x150
device_release_driver_internal+0x308/0x478
device_release_driver+0x1c/0x30
bus_remove_device+0x1a8/0x368
device_del+0x2e0/0x7b0
usb_disable_device+0x244/0x540
usb_disconnect+0x220/0x758
hub_event+0x105c/0x35e0
process_one_work+0x760/0x17b0
worker_thread+0x768/0xce8
kthread+0x3bc/0x690
ret_from_fork+0x10/0x20
irq event stamp: 211604
hardirqs last enabled at (211603): [<ffffffc0828cc9ec>] _raw_spin_unlock_irqrestore+0x84/0x98
hardirqs last disabled at (211604): [<ffffffc0828a9a84>] el1_dbg+0x24/0x80
softirqs last enabled at (211296): [<ffffffc080095f10>] handle_softirqs+0x820/0xbc8
softirqs last disabled at (210993): [<ffffffc080010288>] __do_softirq+0x18/0x20
---[ end trace 0000000000000000 ]---
lan78xx 1-1:1.0 enu1: failed to kill vid 0081/0
Fixes: e110bc825897 ("net: usb: lan78xx: Convert to PHYLINK for improved PHY and MAC management")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Do not configure Latency Tolerance Messaging (LTM) on USB 2.0 hardware.
The LAN7850 is a High-Speed (USB 2.0) only device and does not support
SuperSpeed features like LTM. Currently, the driver unconditionally
attempts to configure LTM registers during initialization. On the
LAN7850, these registers do not exist, resulting in writes to invalid
or undocumented memory space.
This issue was identified during a port to the regmap API with strict
register validation enabled. While no functional issues or crashes have
been observed from these invalid writes, bypassing LTM initialization
on the LAN7850 ensures the driver strictly adheres to the hardware's
valid register map.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Account for hardware auto-padding in TX byte counters to reflect actual
wire traffic.
The LAN7850 hardware automatically pads undersized frames to the minimum
Ethernet frame length (ETH_ZLEN, 60 bytes). However, the driver tracks
the network statistics based on the unpadded socket buffer length. This
results in the tx_bytes counter under-reporting the actual physical
bytes placed on the Ethernet wire for small packets (like short ARP or
ICMP requests).
Use max_t() to ensure the transmission statistics accurately account for
the hardware-generated padding.
Fixes: d383216a7efe ("lan78xx: Introduce Tx URB processing improvements")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Do not drop packets with checksum errors at the USB driver level;
pass them to the network stack.
Previously, the driver dropped all packets where the 'Receive Error
Detected' (RED) bit was set, regardless of the specific error type. This
caused packets with only IP or TCP/UDP checksum errors to be dropped
before reaching the kernel, preventing the network stack from accounting
for them or performing software fallback.
Add a mask for hard hardware errors to safely drop genuinely corrupt
frames, while allowing checksum-errored frames to pass with their
ip_summed field explicitly set to CHECKSUM_NONE.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260305143429.530909-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260305105006.16415-1-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c7159e960f14 ("usbnet: limit max_mtu based on device's hard_mtu")
capped net->max_mtu to the device's hard_mtu in usbnet_probe(). While
this correctly prevents oversized packets on standard USB network
devices, it breaks the qmi_wwan driver.
qmi_wwan relies on userspace (e.g. ModemManager) setting a large MTU on
the wwan0 interface to configure rx_urb_size via usbnet_change_mtu().
QMI modems negotiate USB transfer sizes of 16,383 or 32,767 bytes, and
the USB receive buffers must be sized accordingly. With max_mtu capped
to hard_mtu (~1500 bytes), userspace can no longer raise the MTU, the
receive buffers remain small, and download speeds drop from >300 Mbps
to ~0.8 Mbps.
Introduce a FLAG_NOMAXMTU driver flag that allows individual usbnet
drivers to opt out of the max_mtu cap. Set this flag in qmi_wwan's
driver_info structures to restore the previous behavior for QMI devices,
while keeping the safety fix in place for all other usbnet drivers.
Fixes: c7159e960f14 ("usbnet: limit max_mtu based on device's hard_mtu")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/CAPh3n803k8JcBPV5qEzUB-oKzWkAs-D5CU7z=Vd_nLRCr5ZqQg@mail.gmail.com/
Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://patch.msgid.link/20260304134338.1785002-1-lvivier@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.0-rc3).
No conflicts.
Adjacent changes:
net/netfilter/nft_set_rbtree.c
fb7fb4016300 ("netfilter: nf_tables: clone set on flush only")
3aea466a4399 ("netfilter: nft_set_rbtree: don't disable bh when acquiring tree lock")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The TRENDnet TUC-ET2G is a RTL8156 based usb ethernet adapter. Add its
vendor and product IDs.
Signed-off-by: Valentin Spreckels <valentin@spreckels.dev>
Link: https://patch.msgid.link/20260226195409.7891-2-valentin@spreckels.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The r8152 driver supports the RTL8156, which is a 2.5Gbit Ethernet controller for
USB 3.0, for which support is added for configuring and displaying the EEE
advertisement status for 2.5GBit connections.
The patch also corrects the determination of whether EEE is active to include
the 2.5GBit connection status and make the determination dependent not on the
desired speed configuration (tp->speed), but on the actual speed used by
the controller. For consistency, this is corrected also for the RTL8152/3.
This was tested on an Edimax EU-4307 V1.0 USB-Ethernet adapter with RTL8156,
and a SECOMP Value 12.99.1115 USB-C 3.1 Ethernet converter with RTL8153.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260224-b4-eee2g5-v2-1-cf5c83df036e@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from IPsec, Bluetooth and netfilter
Current release - regressions:
- wifi: fix dev_alloc_name() return value check
- rds: fix recursive lock in rds_tcp_conn_slots_available
Current release - new code bugs:
- vsock: lock down child_ns_mode as write-once
Previous releases - regressions:
- core:
- do not pass flow_id to set_rps_cpu()
- consume xmit errors of GSO frames
- netconsole: avoid OOB reads, msg is not nul-terminated
- netfilter: h323: fix OOB read in decode_choice()
- tcp: re-enable acceptance of FIN packets when RWIN is 0
- udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb().
- wifi: brcmfmac: fix potential kernel oops when probe fails
- phy: register phy led_triggers during probe to avoid AB-BA deadlock
- eth:
- bnxt_en: fix deleting of Ntuple filters
- wan: farsync: fix use-after-free bugs caused by unfinished tasklets
- xscale: check for PTP support properly
Previous releases - always broken:
- tcp: fix potential race in tcp_v6_syn_recv_sock()
- kcm: fix zero-frag skb in frag_list on partial sendmsg error
- xfrm:
- fix race condition in espintcp_close()
- always flush state and policy upon NETDEV_UNREGISTER event
- bluetooth:
- purge error queues in socket destructors
- fix response to L2CAP_ECRED_CONN_REQ
- eth:
- mlx5:
- fix circular locking dependency in dump
- fix "scheduling while atomic" in IPsec MAC address query
- gve: fix incorrect buffer cleanup for QPL
- team: avoid NETDEV_CHANGEMTU event when unregistering slave
- usb: validate USB endpoints"
* tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
netfilter: nf_conntrack_h323: fix OOB read in decode_choice()
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
net: consume xmit errors of GSO frames
vsock: document write-once behavior of the child_ns_mode sysctl
vsock: lock down child_ns_mode as write-once
selftests/vsock: change tests to respect write-once child ns mode
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
net/mlx5: Fix missing devlink lock in SRIOV enable error path
net/mlx5: E-switch, Clear legacy flag when moving to switchdev
net/mlx5: LAG, disable MPESW in lag_disable_change()
net/mlx5: DR, Fix circular locking dependency in dump
selftests: team: Add a reference count leak test
team: avoid NETDEV_CHANGEMTU event when unregistering slave
net: mana: Fix double destroy_workqueue on service rescan PCI path
MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER
dpll: zl3073x: Remove redundant cleanup in devm_dpll_init()
selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0
tcp: re-enable acceptance of FIN packets when RWIN is 0
vsock: Use container_of() to get net namespace in sysctl handlers
net: usb: kaweth: validate USB endpoints
...
|
|
The kaweth driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://patch.msgid.link/2026022305-substance-virtual-c728@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kalmia driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: d40261236e8e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Link: https://patch.msgid.link/2026022326-shack-headstone-ef6f@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
