| Age | Commit message (Collapse) | Author |
|---|
|
After U-Boot initializes PCIe with "pcie enum", Linux fails to detect
an NVMe disk on some boot cycles with:
phy phy-32f00000.pcie-phy.0: phy poweron failed --> -110
Discussion with NXP identified that the iMX8MP PCIe PHY PLL may fail to
lock when re-initialized without a reset cycle [1].
The issue reproduces on 7% of tested hardware platforms, with a 30-40%
failure rate per affected device across boot cycles.
Insert a reset cycle in the power-on routine to ensure the PHY is
initialized from a known state.
[1] https://community.nxp.com/t5/i-MX-Processors/iMX8MP-PCIe-initialization-in-U-Boot/m-p/2248437#M242401
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251223150254.1075221-1-rafael@beims.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The for_each_available_child_of_node() calls of_node_put() to
release child_np in each success loop. After breaking from the
loop with the child_np has been released, the code will jump to
the put_child label and will call the of_node_put() again if the
devm_request_threaded_irq() fails. These cause a double free bug.
Fix by returning directly to avoid the duplicate of_node_put().
Fixes: ed2b5a8e6b98 ("phy: phy-rockchip-inno-usb2: support muxed interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260109154626.2452034-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
"family" is an enum, thus cast of pointer on 64-bit compile test with
clang W=1 causes:
phy-bcm-ns-usb3.c:206:17: error: cast to smaller integer type 'enum bcm_ns_family' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
This was already fixed in commit bd6e74a2f0a0 ("phy: broadcom: ns-usb3:
fix Wvoid-pointer-to-enum-cast warning") but then got bad in commit
21bf6fc47a1e ("phy: Use device_get_match_data()").
Note that after various discussions the preferred cast is via "unsigned
long", not "uintptr_t".
Fixes: 21bf6fc47a1e ("phy: Use device_get_match_data()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251224115533.154162-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The USB2 Bias Pad Control register manages analog parameters for signal
detection. Previously, the HS_DISCON_LEVEL relied on hardware reset
values, which may lead to the detection failure.
Explicitly configure HS_DISCON_LEVEL to 0x7. This ensures the disconnect
threshold is sufficient to guarantee reliable detection.
Fixes: bbf711682cd5 ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://patch.msgid.link/20251212032116.768307-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When the OTG USB port is used to power to SoC, configured as peripheral and
used in gadget mode, communication stops without notice about 6 seconds
after the gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The related code flow in the PHY driver code can be summarized as:
* the first time chg_detect_work starts (6 seconds after gadget is
configured and enumerated)
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, false); [Y]
* rockchip_chg_detect_work() changes state and re-triggers itself a few
times until it reaches the DETECTED state:
-> rockchip_chg_detect_work():
if chg_state is DETECTED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, true); [Z]
At [Y] all existing communications stop. E.g. using a CDC serial gadget,
the /dev/tty* devices are still present on both host and device, but no
data is transferred anymore. The later call with a 'true' argument at [Z]
does not restore it.
Due to the lack of documentation, what chg_det.opmode does exactly is not
clear, however by code inspection it seems reasonable that is disables
something needed to keep the communication working, and testing proves that
disabling these lines lets gadget mode keep working. So prevent changes to
chg_det.opmode when there is a cable connected (VBUS present).
Fixes: 98898f3bc83c ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-2-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When the OTG USB port is used to power the SoC, configured as peripheral
and used in gadget mode, there is a disconnection about 6 seconds after the
gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The problem happens because of the PHY driver code flow, summarized as:
* UDC start code (triggered via configfs at any time after boot)
-> phy_init
-> rockchip_usb2phy_init
-> schedule_delayed_work(otg_sm_work [A], 6 sec)
-> phy_power_on
-> rockchip_usb2phy_power_on
-> enable clock
-> rockchip_usb2phy_reset
* Now the gadget interface is up and running.
* 6 seconds later otg_sm_work starts [A]
-> rockchip_usb2phy_otg_sm_work():
if (B_IDLE state && VBUS present && ...):
schedule_delayed_work(&rport->chg_work [B], 0);
* immediately the chg_detect_work starts [B]
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
if (!rport->suspended):
rockchip_usb2phy_power_off() <--- [X]
At [X], the PHY is powered off, causing a disconnection. This quickly
triggers a new connection and following re-enumeration, but any connection
that had been established during the 6 seconds is broken.
The code already checks for !rport->suspended (which, somewhat
counter-intuitively, means the PHY is powered on), so add a guard for VBUS
as well to avoid a disconnection when a cable is connected.
Fixes: 98898f3bc83c ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Co-developed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-1-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The mmio regmap that may be allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind.
Fixes: 5ab90f40121a ("phy: ti: gmii-sel: Do not use syscon helper to build regmap")
Cc: stable@vger.kernel.org # 6.14
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20251127134834.2030-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
LAN969x uses the SparX-5 SERDES driver, so make it selectable for
ARCH_LAN969X.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Gabor Juhos <j4g8y7@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251031121834.665987-1-robert.marko@sartura.hr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
devm_pm_runtime_enable() can fail due to memory allocation. The current
code ignores its return value after calling pm_runtime_set_active(),
leaving the device in an inconsistent state if runtime PM initialization
fails.
Check the return value of devm_pm_runtime_enable() and return on
failure. Also move the declaration of 'ret' to the function scope
to support this check.
Fixes: ee8e41b5044f ("phy: ti: phy-da8xx-usb: Add runtime PM support")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251124105734.1027-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The "index" variable is used as an index into the usbphyc->phys[] array
which has usbphyc->nphys elements. So if it is equal to usbphyc->nphys
then it is one element out of bounds. The "index" comes from the
device tree so it's data that we trust and it's unlikely to be wrong,
however it's obviously still worth fixing the bug. Change the > to >=.
Fixes: 94c358da3a05 ("phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://patch.msgid.link/aTfHcMJK1wFVnvEe@stanley.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Enabling runtime PM before attaching the QPHY instance as driver data
can lead to a NULL pointer dereference in runtime PM callbacks that
expect valid driver data. There is a small window where the suspend
callback may run after PM runtime enabling and before runtime forbid.
This causes a sporadic crash during boot:
```
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a1
[...]
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.7+ #116 PREEMPT
Workqueue: pm pm_runtime_work
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : qusb2_phy_runtime_suspend+0x14/0x1e0 [phy_qcom_qusb2]
lr : pm_generic_runtime_suspend+0x2c/0x44
[...]
```
Attach the QPHY instance as driver data before enabling runtime PM to
prevent NULL pointer dereference in runtime PM callbacks.
Reorder pm_runtime_enable() and pm_runtime_forbid() to prevent a
short window where an unnecessary runtime suspend can occur.
Use the devres-managed version to ensure PM runtime is symmetrically
disabled during driver removal for proper cleanup.
Fixes: 891a96f65ac3 ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20251219085640.114473-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Clear the PCS_TX_SWING_FULL field mask before setting the new value
in PHY_CTRL5 register. Without clearing the mask first, the OR operation
could leave previously set bits, resulting in incorrect register
configuration.
Fixes: 63c85ad0cd81 ("phy: fsl-imx8mp-usb: add support for phy tuning")
Suggested-by: Leonid Segal <leonids@variscite.com>
Acked-by: Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://patch.msgid.link/20251219160912.561431-1-stefano.r@variscite.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Currently, the PHY only registers the typec orientation switch when it
is built in. If the typec driver is built as a module, the switch
registration is skipped due to the preprocessor condition, causing
orientation detection to fail.
With commit
45fe729be9a6 ("usb: typec: Stub out typec_switch APIs when CONFIG_TYPEC=n")
the preprocessor condition is not needed anymore and the orientation
switch is correctly registered for both built-in and module builds.
Fixes: b58f0f86fd61 ("phy: fsl-imx8mq-usb: add tca function driver for imx95")
Cc: stable@vger.kernel.org
Suggested-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20251126140136.1202241-1-fra.schnyder@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This phy supports both 24MHz and 100MHz clock inputs. By default it's
using XTAL 24MHz and the 100MHz clock is a alternate reference clock.
Add supports to use alternate reference clock in case 24MHz clock
can't work well.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20251118071947.2504789-2-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fixup PHY deskew FIFO to prevent the phase of D2 lane going ahead of
other lanes. It's worth noting this might only happen when dealing with
HDMI 2.0 rates.
Fixes: 553be2830c5f ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028-phy-hdptx-fixes-v1-3-ecc642a59d94@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Due to its relatively low frequency, a noise stemming from the 24MHz PLL
reference clock may traverse the low-pass loop filter of ROPLL, which
could potentially generate some HDMI flash artifacts.
Reduce ROPLL loop bandwidth in an attempt to mitigate the problem.
Fixes: 553be2830c5f ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028-phy-hdptx-fixes-v1-2-ecc642a59d94@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When making use of the clock provider functionality, the output clock
does normally match the TMDS character rate, which is what the PHY PLL
gets configured to.
However, this is only applicable for default color depth of 8 bpc. For
higher depths, the output clock is further divided by the hardware
according to the formula:
output_clock_rate = tmds_char_rate * 8 / bpc
Since the existence of the clock divider wasn't taken into account when
support for high bpc has been introduced, make the necessary adjustments
to report the correct clock rate.
Fixes: 9d0ec51d7c22 ("phy: rockchip: samsung-hdptx: Add high color depth management")
Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028-phy-hdptx-fixes-v1-1-ecc642a59d94@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The "phy_id" comes from the device tree so it's going to be correct.
But static checkers sometimes complain when we have an upper bounds
check with no lower bounds check. Also it's a bit unusual that the
lowest valid number is 1 instead of 0 so adding a check could
potentially help someone.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/aPJpB-QI8FMpFGOk@stanley.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for Gen5 x4 PCIe QMP PHY found on Glymur platform.
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Wenbin Yao <wenbin.yao@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251103-glymur-pcie-upstream-v6-3-18a5e0a538dc@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The new Glymur SoC bumps up the HW version of QMP phy to v8.50 for PCIE
g5x4. Add the new PCS offsets in a dedicated header file.
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Wenbin Yao <wenbin.yao@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251103-glymur-pcie-upstream-v6-2-18a5e0a538dc@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Initialize priv->lock to fix the following warning.
WARNING: CPU: 0 PID: 12 at kernel/locking/mutex.c:577 __mutex_lock+0x70c/0x8b8
Modules linked in:
Hardware name: Freescale i.MX8QM MEK (DT)
Call trace:
__mutex_lock+0x70c/0x8b8 (P)
mutex_lock_nested+0x24/0x30
imx_hsio_power_on+0x4c/0x764
phy_power_on+0x7c/0x12c
imx_pcie_host_init+0x1d0/0x4d4
dw_pcie_host_init+0x188/0x4b0
imx_pcie_probe+0x324/0x6f4
platform_probe+0x5c/0x98
really_probe+0xbc/0x29c
__driver_probe_device+0x78/0x12c
driver_probe_device+0xd8/0x160
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x84/0xe4
__device_attach_async_helper+0xb8/0xdc
async_run_entry_fn+0x34/0xe0
process_one_work+0x220/0x694
worker_thread+0x1c0/0x36c
kthread+0x14c/0x224
Fixes: 82c56b6dd24f ("phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20250925013806.569658-1-xiaolei.wang@windriver.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Semicolons after end of function braces are not needed, remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/a8807dafa87fcc3abcafd34a1895e4c722c39793.1758719985.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Certain platforms may not have the PHY_ENABLE bit set on power on reset.
Update the current sequence to explicitly write to enable the PHY_ENABLE
bit. This ensures that regardless of the platform, the PHY is properly
enabled.
Signed-off-by: Ronak Raheja <ronak.raheja@oss.qualcomm.com>
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20250920032158.242725-1-wesley.cheng@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The QMP USB3/DP Combo PHY hosts an USB3 phy and a DP PHY on top
of a combo glue to route either lanes to the 4 shared physical lanes.
The routing of the lanes can be:
- 2 DP + 2 USB3
- 4 DP
- 2 USB3
Get the lanes mapping from DT and stop registering the USB-C
muxes in favor of a static mode and orientation detemined
by the lanes mapping.
This allows supporting boards with direct connection of USB3 and
DisplayPort lanes to the QMP Combo PHY lanes, not using the
USB-C Altmode feature.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Xilin Wu <sophon@radxa.com> # qcs6490-radxa-dragon-q6a
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251119-topic-x1e80100-hdmi-v7-2-2bee0e66cc1b@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When PCIe link enters L1 PM substates, the PHY will turn off its
PLL for power-saving. However, it turns off the PLL too fast which
leads the PHY to be broken. According to the PHY document, we need
to delay PLL turnoff time.
Fixes: f13bff25161b ("phy: rockchip-naneng-combo: Support rk3562")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/1763459526-35004-2-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When PCIe link enters L1 PM substates, the PHY will turn off its
PLL for power-saving. However, it turns off the PLL too fast which
leads the PHY to be broken. According to the PHY document, we need
to delay PLL turnoff time.
Fixes: bbcca4fac873 ("phy: rockchip: naneng-combphy: Add RK3528 support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/1763459526-35004-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The Renesas RZ/G3S supports a power saving mode where power to most of the
SoC components is turned off. The USB PHY is among these components.
Because of this the settings applied in driver probe need to be executed
also on resume path. On suspend path only reset signal need to be asserted.
Add suspend/resume support.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251119120418.686224-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Move the check of phy_data->init_bus from rcar_gen3_phy_usb2_init_bus()
to rcar_gen3_phy_usb2_probe() to avoid having it duplicated in both the
probe path and the upcoming resume code. This is a preparatory patch.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251119120418.686224-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
rcar_gen3_phy_usb2_probe()
If an error occurs after the reset_control_deassert(),
reset_control_assert() must be called, as already done in the remove
function.
Use devm_add_action_or_reset() to add the missing call and simplify the
.remove() function accordingly.
While at it, drop struct rcar_gen3_chan::rstc as it is not used aymore.
[claudiu.beznea: removed "struct reset_control *rstc = data;" from
rcar_gen3_reset_assert(), dropped struct rcar_gen3_chan::rstc]
Fixes: 4eae16375357 ("phy: renesas: rcar-gen3-usb2: Add support to initialize the bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251023135810.1688415-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit f4fb9c4d7f94 ("phy: exynos5-usbdrd: allow DWC3 runtime suspend
with UDC bound (E850+)") incorrectly added clk_bulk_disable() as the
inverse of clk_bulk_prepare_enable() while it should have of course
used clk_bulk_disable_unprepare(). This means incorrect reference
counts to the CMU driver remain.
Update the code accordingly.
Fixes: f4fb9c4d7f94 ("phy: exynos5-usbdrd: allow DWC3 runtime suspend with UDC bound (E850+)")
CC: stable@vger.kernel.org
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://patch.msgid.link/20251006-gs101-usb-phy-clk-imbalance-v1-1-205b206126cf@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Platform drivers can be probed after their init sections have been
discarded (e.g. on probe deferral or manual rebind through sysfs) so the
probe function and match table must not live in init.
Fixes: 783f6d3dcf35 ("phy: bcm63xx-usbh: Add BCM63xx USBH driver")
Cc: stable@vger.kernel.org # 5.9
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251017054537.6884-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
For MIPI mode, the inno-dsidphy found on RK3506 supports up to 2 lanes
and a maximum data rate of 1.5GHz.
Signed-off-by: Hongming Zou <hongming.zou@rock-chips.com>
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251106020632.92-7-kernel@airkyi.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
setup
Replace the custom qmp_regulator_data structure with the standard
regulator_bulk_data and use the init_load_uA field to set regulator
load during initialization.
This change simplifies the regulator setup by removing manual
allocation and load configuration logic, and leverages
devm_regulator_bulk_get_const() to automatically apply load settings
before enabling regulators.
Signed-off-by: Faisal Hassan <faisal.hassan@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://patch.msgid.link/20250922135901.2067-1-faisal.hassan@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Biju <biju.das.au@gmail.com> says:
This patch series aims to add Renesas RZ/G3E USB3.0 PHY driver support.
This module is connected between USB3 Host and PHY module. The main
functions of this module are:
1) Reset control
2) Control of PHY input pins
3) Monitoring of PHY output pins
Biju Das (2):
dt-bindings: phy: renesas: Document Renesas RZ/G3E USB3.0 PHY
phy: renesas: Add Renesas RZ/G3E USB3.0 PHY driver
Link: https://patch.msgid.link/20251029084037.108610-1-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add Renesas RZ/G3E USB3.0 PHY driver. This module is connected
between USB3 Host and PHY module. The main functions of this
module are:
1) Reset control
2) Control of PHY input pins
3) Monitoring of PHY output pins
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20251029084037.108610-3-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Remove extra space after '=' to comply with coding style.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Implement the .notify_phystate() callback and provide the gs101 specific
phy values that need to be programmed when entering and exiting the hibern8
state.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251112-phy-notify-pmstate-v5-2-39df622d8fcb@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add a new phy_notify_state() api that notifies and configures a phy for a
given state transition.
This is intended to be used by phy drivers which need to do some runtime
configuration of parameters that can't be handled by phy_calibrate() or
phy_power_{on|off}().
The first usage of this API is in the Samsung UFS phy that needs to issue
some register writes when entering and exiting the hibernate link state.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251112-phy-notify-pmstate-v5-1-39df622d8fcb@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Peng Fan <peng.fan@nxp.com> says:
TJA1048 is a Dual channel can transceiver with Sleep mode supported.
TJA105{1,7} is a Single Channel can transceiver with Sleep mode supported.
Link: https://patch.msgid.link/20251001-can-v7-0-fad29efc3884@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Support TJA105{1,7} which are a single channel high-speed CAN transceiver
with silent mode supported.
phy mode is not implemented as of now. silent settings are kept in
phy_power_on and phy_power_off. After phy mode is supported, the silent
settings could be moved to phy_set_mode.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20251001-can-v7-5-fad29efc3884@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
gpiod_set_value_cansleep has an internal check on gpio_desc using
'VALIDATE_DESC(desc)', the check before invoking gpiod_set_value_cansleep
could be removed.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20251001-can-v7-4-fad29efc3884@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
- Introduce new flag CAN_TRANSCEIVER_DUAL_CH to indicate the phy has two
channels.
- Alloc a phy for each channel
- Support TJA1048 which is a dual high-speed CAN transceiver with sleep
mode supported.
- Add can_transceiver_phy_xlate for parsing phy
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20251001-can-v7-3-fad29efc3884@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
To prepare for dual-channel phy support, introduce can_transceiver_priv as
a higher level encapsulation for phy.
No functional changes.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20251001-can-v7-2-fad29efc3884@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"The usual bunch of device support and update to drivers.
New Support
- Qualcomm SM8750 QMP PCIe PHY dual lane support, PMIV0104 eusb2
repeater support, QCS8300 eDP PHY support
- Renesas RZ/T2H and RZ/N2H support and updates to driver for that
- TI TCAN1051 phy support
- Rockchip rk3588 dphy support, RK3528 combphy support
Updates:
- cadence updates for calibration and polling for ready and enabling
of lower resolutions, runtime pm support,
- Rockchip: enable U3 otg port
- Renesas USXGMII mode support
- Qualcomm UFS PHY and PLL regulator load support"
* tag 'phy-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (64 commits)
phy: rockchip: phy-rockchip-inno-csidphy: add support for rk3588 variant
phy: rockchip: phy-rockchip-inno-csidphy: allow for different reset lines
phy: rockchip: phy-rockchip-inno-csidphy: allow writes to grf register 0
dt-bindings: phy: rockchip-inno-csi-dphy: add rk3588 variant
dt-bindings: phy: rockchip-inno-csi-dphy: make power-domains non-required
phy: cadence: cdns-dphy: Enable lower resolutions in dphy
phy: renesas: r8a779f0-ether-serdes: add new step added to latest datasheet
phy: renesas: r8a779f0-ether-serdes: add USXGMII mode
phy: sophgo: Add USB 2.0 PHY driver for Sophgo CV18XX/SG200X
dt-bindings: phy: Add Sophgo CV1800 USB phy
phy: cadence: cdns-dphy: Update calibration wait time for startup state machine
phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling
phy: renesas: rcar-gen3-usb2: Fix ID check logic with VBUS valid
dt-bindings: phy: ti,tcan104x-can: Document TI TCAN1051
phy: lynx-28g: check return value when calling lynx_28g_pll_get
phy: qcom: m31-eusb2: Fix the error log while enabling clock
phy: rockchip: usbdp: Remove redundant ternary operators
phy: renesas: rcar-gen3-usb2: Remove redundant ternary operators
phy: hisilicon: Remove redundant ternary operators
phy: qcom-qmp-ufs: Add PHY and PLL regulator load
...
|
|
Pull bitmap updates from Yury Norov:
- FIELD_PREP_WM16() consolidation (Nicolas)
- bitmaps for Rust (Burak)
- __fls() fix for arc (Kees)
* tag 'bitmap-for-6.18' of https://github.com/norov/linux: (25 commits)
rust: add dynamic ID pool abstraction for bitmap
rust: add find_bit_benchmark_rust module.
rust: add bitmap API.
rust: add bindings for bitops.h
rust: add bindings for bitmap.h
phy: rockchip-pcie: switch to FIELD_PREP_WM16 macro
clk: sp7021: switch to FIELD_PREP_WM16 macro
PCI: dw-rockchip: Switch to FIELD_PREP_WM16 macro
PCI: rockchip: Switch to FIELD_PREP_WM16* macros
net: stmmac: dwmac-rk: switch to FIELD_PREP_WM16 macro
ASoC: rockchip: i2s-tdm: switch to FIELD_PREP_WM16_CONST macro
drm/rockchip: dw_hdmi: switch to FIELD_PREP_WM16* macros
phy: rockchip-usb: switch to FIELD_PREP_WM16 macro
drm/rockchip: inno-hdmi: switch to FIELD_PREP_WM16 macro
drm/rockchip: dw_hdmi_qp: switch to FIELD_PREP_WM16 macro
phy: rockchip-samsung-dcphy: switch to FIELD_PREP_WM16 macro
drm/rockchip: vop2: switch to FIELD_PREP_WM16 macro
drm/rockchip: dsi: switch to FIELD_PREP_WM16* macros
phy: rockchip-emmc: switch to FIELD_PREP_WM16 macro
drm/rockchip: lvds: switch to FIELD_PREP_WM16 macro
...
|
|
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
The Rockchip PCIe PHY driver, used on the RK3399, has its own definition
of HIWORD_UPDATE.
Remove it, and replace instances of it with hw_bitfield.h's
FIELD_PREP_WM16. To achieve this, some mask defines are reshuffled, as
FIELD_PREP_WM16 uses the mask as both the mask of bits to write and to
derive the shift amount from in order to shift the value.
In order to ensure that the mask is always a constant, the inst->index
shift is performed after the FIELD_PREP_WM16, as this is a runtime
value.
>From this, we gain compile-time error checking, and in my humble opinion
nicer code, as well as a single definition of this macro across the
entire codebase to aid in code comprehension.
Tested on a RK3399 ROCKPro64, where PCIe still works as expected when
accessing an NVMe drive.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
The Rockchip RK3588 MIPI CSI-2 DPHY can be supported using the existing
phy-rockchip-inno-csidphy driver, the notable differences being
- the control bits in the GRF
- the additional reset line
Add support for this variant.
Signed-off-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://lore.kernel.org/r/20250616-rk3588-csi-dphy-v4-6-a4f340a7f0cf@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The RK3588 MIPI CSI-2 DPHY variant requires two reset lines. Add support
for different sets of reset lines to the phy-rockchip-inno-csidphy driver
as preparation for the introduction of the RK3588 variant.
Signed-off-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://lore.kernel.org/r/20250616-rk3588-csi-dphy-v4-5-a4f340a7f0cf@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver for the Rockchip MIPI CSI-2 DPHY uses GRF register offset
value 0 to sort out undefined registers. However, the RK3588 CSIDPHY GRF
this offset is perfectly fine (in fact, register 0 is the only one in
this register file).
Introduce a boolean variable to indicate valid registers and allow writes
to register 0.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://lore.kernel.org/r/20250616-rk3588-csi-dphy-v4-4-a4f340a7f0cf@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
