| Age | Commit message (Collapse) | Author |
|---|
|
The KSZ8463 switch supports PTP but it's not supported by the driver.
Add L2 two-step PTP support for the KSZ8463. IPv4 and IPv6 layers aren't
supported. Neither is one-step PTP. Use KSZ8463-specific implementations
of the .get_ts_info and .port_hwtstamp_set callbacks.
The pdelay_req and pdelay_resp timestamps share one interrupt bit status
while they're located in two different registers. So introduce
last_tx_is_pdelayresp to keep track of the last sent event type. This
flag is set by the xmit worker right before sending the packet and then
used in the interrupt handler to retrieve the timestamp location.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-10-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Detection of L2 PTP frames needs to be enabled for PTP to work at the L2
layer. The bit enabling this detection is set by default on the switches
currently supported by the driver, but it is unset by default on the
KSZ8463 for which support will be added in upcoming patches.
Explicitly enable the detection of L2 PTP frames for all switches when
PTP is enabled.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-9-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8463 uses the KSZ9893 DSA TAG driver. However, the KSZ8463 doesn't
use the tail tag to convey timestamps to the host as KSZ9893 does. It
uses the reserved fields in the PTP header instead.
Add a KSZ8463-specific DSA_TAG driver to handle KSZ8463 timestamps.
There is no information in the tail tag to distinguish PTP packets from
others so use the ptp_classify_raw() helper to find the PTP packets and
extract the timestamp from their PTP headers.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-8-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In KSZ8463 register's layout, the offset between port 1 and port 2
registers isn't the same in the generic control register area than in
the PTP register area. The get_port_addr() always uses the same offset
so it doesn't work when it's used to access PTP registers.
Adapt the port offset in get_port_addr() when the accessed register is
in the PTP area.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-5-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8463 PTP interrupts aren't handled by the driver.
The interrupt layout in KSZ8463 has nothing to do with the other
switches:
- Its global interrupt enable register is 16-bits long and follow an
'enable' logic, instead of a 'mask' one
- all the interrupts of all ports are grouped into one status register
while others have one interrupt register per port
- xdelay_req and pdresp timestamps share one single interrupt bit on the
KSZ8463 while each of them has its own interrupt bit on other switches
Create a KSZ8463-specific set of interrupt domain operations to handle
the global IRQ layer. To limit code duplication, it uses the same
interrupt handler than the other switches. Since other switches have
8-bits registers, only the high-byte of the interrupt status/enable
registers are used. This high-byte is where the PTP interrupts are
located. The low-byte contains the wake-up detection interrupts so if at
some points these interrupts are needed we'll need a bit of rework here.
Create KSZ8463-specific functions to setup the PTP interrupts. The
created IRQ domain is tied to the first port of the KSZ8463. Again,
the same PTP interrupt handler than the others switches is used.
Implement the teardown callback to release the interrupts.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-4-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IRQ setup uses an hardcoded set of IRQ operations. These operations
don't fit with the KSZ8463 which has an inverted bit logic (it uses an
'enable irq' register instead of a 'mask irq' one) and 16-bits registers.
Take the IRQ domain operations as input of ksz_irq_common_setup() to
allow KSZ8463 to use the already existing setup with its own set of IRQ
operations.
Expose ksz_irq_common_setup() and ksz_irq_bus_lock/unlock() so they can
be used by ksz8.c.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-3-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz8_config_cpu_port() is only called twice, once by ksz8_setup() and
once by ksz8463_setup(). It contains a ksz8463 branch that could be
avoided in the ksz8_setup() case and a ksz87xx/ksz88xx branches that
could be avoided in ksz8463_setup() case.
Create ksz8463_config_cpu_port() that only handles the ksz8463 case and
remove the ksz8463 specificities from the common ksz8_config_cpu_port().
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-2-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8463 uses the ksz8_setup() as setup() callback for its DSA
operations. Its behavior is quite different than other KSZ8 switches,
especially its interrupt scheme.
Remove from the ksz8_setup()/ksz8_reset_switch() everything that is
ksz8463-related.
Create a dedicated ksz8463_setup() and a ksz8463_reset_switch() function.
This new ksz8463_setup() is widely inspired from ksz8_setup, it has
following differences:
- it doesn't configure drive strength (not supported on KSZ8463)
- it uses the ksz8463_reset_switch()
- it doesn't call ksz8_handle_global_errata() (the handled errata only
affects the KSZ87xx variant)
- it doesn't configure IRQs. Note that ksz8_setup()'s IRQ initialization
doesn't work for the KSZ8463 anyway. Proper support for it comes in
upcoming patches.
Remove the teardown implementation from the KSZ8463 operations. Since
PTP and interrupts aren't setup, the common ksz_teardown() wouldn't do
anything anyway.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260727-ksz-new-ptp-v3-1-caba39e680e3@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All other log messages in the driver prefix hex values with 0x, add it
in the one missing message. While at it also add the missing opening
parenthesis in the same log message.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260722174853.2316333-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Don't populate the read-only const array ts_reg on the stack
at run time, instead make it static
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20260714191406.195375-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.2-rc3).
Conflicts:
tools/testing/selftests/net/lib.sh
dd6a23bac306b ("selftests: net: make busywait timeout clock portable")
895bad9cc4cec ("selftests: net: make busywait timeout clock portable")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The drive strength configuration is done during the setup of all
switches through a common function that then has specific behavior
depending on the switch identity.
Split the common configuration in two functions: one is dedicated to the
KSZ8 family, the other is dedicated to the KSZ9477 family.
Remove the drive strength configuration from the lan937x_setup since
the LAN937x family doesn't support it.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-10-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz9477_drive_strength_write() isn't used for the KSZ9477-family only.
It's also used for the KSZ87xx chip variants. This function name is
misleading.
Rename it ksz_drive_strength_write().
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-9-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz9477_set_default_prio_queue_mapping() dictates a KSZ9477-specific
behavior but is defined in the common section of the code.
Move its definition to the KSZ9477-specific area.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-8-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The setup of QDISC_ETS isn't the same for the KSZ8 switches than for
the other switches. It leads to is_ksz8() branches in the common code.
Move the KSZ8-specific portions into ksz8.c by creating two setup_tc()
functions, one dedicated to the KSZ87xx family that only handles the
TC_SETUP_QDISC_CBS case, one for the rest of the KSZ8 that handles both
TC_SETUP_QDISC_CBS and TC_SETUP_QDISC_ETS cases.
It remains some is_kszXXXX() branches because inside the ksz88xx family,
only the ksz88x3 switches support QDISC_ETS.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-7-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The KSZ9477 PHY errata is handled from the common ksz_r_mib_stat64().
This errata clearly belongs to the KSZ9477 family so it should be handled
from the ksz9477-specific portion of the driver.
Create a ksz9477-specific r_mib_stat64() implementation that handles
this errata.
Remove the errata handling from the common ksz_r_mib_stat64().
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-6-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz_get_gbit() and ksz_get_xmii() are defined in the ksz_common while
they are only used by the ksz9477 driver.
Move their definition into ksz9477.c
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-5-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz88xx_r_mib_stats64() is defined in ksz_common while it's clearly
ksz88xx-specific.
Move its definition in ksz8.c
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-4-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz_is_port_mac_global_usable() is exposed in ksz_common.h while it's
only used internally.
Make ksz_is_port_mac_global_usable() static.
Move its definition above its first call.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-3-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz_max_mtu() is a bit cluttered. It would be good for developers and
reviewers if they didn't need to look at a common function for hardware
they likely don't have, and which is vastly different, when they are
interested in only a specific chip.
Benefit from the fact that all families listed here have their own
dsa_switch_ops, and provide separate implementations for the
port_max_mtu() method.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-2-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Even among the ksz8 family, there are big differences in the MTU change
procedure between KSZ87xx and KSZ88xx (KSZ8463 is like KSZ88xx here).
Since we have 3 separate dsa_switch_ops for what constitutes "KSZ8", we
can split those procedures into separate functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260702-clean-ksz-4th-v1-1-93441e695fa4@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
files)
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
|
|
linux/gpio.h should no longer be used, change these in drivers/net to
linux/gpio/consumer.h where possible, with b53 being the only one still
using linux/gpio/legacy.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260629132633.1300009-7-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The port_teardown() operation is optional. Yet, it is implemented by all
the KSZ switches through a common function that doesn't do anything for
the switches that aren't part of the ksz9477 family
Remove the implementation from the switches that don't need it.
Implement instead a ksz9477-specific port_teardown.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-10-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the switches use a common mdio_register() function that uses two
ksz_dev_ops callbacks (.mdio_bus_preinit() and .create_phy_addr_map())
to handle the lan937x specific case. These two callbacks are used only
at this place in the code.
Implement a new lan937x-specific MDIO registration functions that uses
these two lan937x-specific functions. The lan937x bindings don't
have any 'interrupts' property so this lan937x_mdio_register() doesn't
call ksz_irq_phy_setup().
Expose the common ksz_*_mdio_{read/write} functions so they can be used
in lan937x.c
Remove the callbacks from ksz_dev_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-9-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All switches implement the optional .port_hsr_join operation while only
the KSZ9477 truly supports it.
Remove the common port_hsr_join implementation.
Replace it with a specific implementation for the KSZ9477 case.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-8-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the KSZ switches use common {get/set}_wol operations while only the
ksz9477 and the ksz87xx families really support it. These operations are
optional so there is no point implementing them to return -EOPNOTSUPP.
Remove the {get/set}_wol callbacks from the switch operations for the
ksz88xx, the ksz8463 and the lan937x families.
Remove the family check from the common {get/set}_wol implementation.
Note that is_ksz9477() is only true for the KSZ9477 so this change will
also add WoL support for the other switches using the
ksz9477_switch_ops. I checked their datasheet, they implement the same
PME_WOL registers, at the same addresses, so this should go fine.
Modify the ksz_wol_pre_shutdown() initial check to ensure consistency in
the WoL handling for these non-KSZ9477 switches using ksz9477_switch_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-7-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The .support_eee() operation is optional. Yet, it is implemented by the
KSZ switches through a common functon that reports false for every chip
except for KSZ8563, KSZ9563 and KSZ9893 from the KSZ9477 family.
Remove the implementation from the switches that don't support EEE.
Also remove .set_mac_eee() for them as .set_mac_eee() is gated by the
`support_eee` presence in the core.
Implement instead a ksz9477-specific support_eee for these three supported
switches.
Note that comment /* KSZ879x/KSZ877x/KSZ876x Errata DS80000687C Module 2 */
is completely removed because it concerns the KSZ87xx family that doesn't
support at all EEE.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-6-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
setup_rgmii_delay() operation is only used once during the common phylink
MAC configuration. Only the lan937x switch implements this
setup_rgmii_delay().
Remove the setup_rgmii_delay operation from ksz_dev_ops.
Implement a lan937x-specific phylink MAC configuration that does this
RGMII delay setup.
Export ksz_set_xmii since it's needed by the lan937x implementation.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-5-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The common .mac_config() implementation checks some conditions before
doing any register access. As this common implementation is about to be
split in the upcoming patch, these checks would lead to code
duplication.
Wrap all the checks in a need_config() function that returns true when
the driver really need to access the switch registers to configure the
MAC.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-4-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The common ksz_get_phy_flags() is used by all the switches to implement
the optional .get_phy_flags DSA operation. It always returns 0 except
for KSZ88X3 switches where an errata has to be handled.
Make ksz_get_phy_flags() ksz88xx-specific.
Remove the get_phy_flags implementation for the switches that don't need
it.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-3-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8463 uses the common KSZ8 implementation for its VLAN operations.
This implementation returns -ENOTSUPP for the KSZ8463 case, which is
pointless.
Remove the VLAN operations from the ksz8463_switch_ops so the core can
directly return -ENOTSUPP.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-2-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the KSZ switches share a common implementation of the
cls_flower_{add/del} operations. These common implementations return
ksz9477-specific implementations for the KSZ9477 family and -EOPNOTSUPP
for the others. -EOPNOTSUPP is already returned by the DSA core when
the operation isn't implemented.
Remove the common implementations.
Directly link the ksz9477_cls_flower_{add/del}() to the KSZ9477 callback.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-1-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the KSZ87xx short cable workaround.
This patch implements the KSZ87xx short cable erratum
described in Microchip document DS80000687C for KSZ87xx switches
and the following support article:
Link: https://support.microchip.com/s/article/Solution-for-Using-CAT-5E-or-CAT-6-Short-Cable-with-a-Link-Issue-for-the-KSZ8795-Family
The issue affects short or low-loss cable links (e.g. CAT5e/CAT6),
where the PHY receiver equalizer may amplify high-amplitude signals
excessively, resulting in internal distortion and link establishment
failures.
KSZ87xx devices require a workaround for the Module 3 low-loss cable
condition, controlled through the switch TABLE_LINK_MD_V indirect
registers.
This change models the erratum handling as vendor-specific Clause 22 PHY
registers, virtualized by the KSZ8 DSA driver and accessed via
ksz8_r_phy() / ksz8_w_phy(). The following controls are provided:
- A boolean “short-cable” preset, which applies a documented and
conservative configuration (LPF 62 MHz bandwidth and DSP EQ initial
value 0), and is the recommended interface for typical use cases.
- Separate LPF bandwidth and DSP EQ initial value controls intended for
advanced or experimental tuning. These are orthogonal and independent,
and override the corresponding settings without requiring any specific
ordering.
The preset and tunables act as simple setters with no implicit state
machine or invalid combinations, keeping the API predictable and aligned
with the KISS principle.
The erratum affects the shared PHY analog front-end and therefore applies
globally to the switch.
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Fidelio Lawson <fidelio.lawson@exotec.com>
Link: https://patch.msgid.link/20260609-ksz87xx_errata_low_loss_connections-v10-1-9ba4418cf3db@exotec.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phy_read() and phy_write() are handled through common functions that
redirect the treatment to ksz_dev_ops callbacks. This layer of
indirection isn't needed since we now have a dsa_switch_ops for each
kind of switch
Remove one indirection layer for KSZ switches, by connecting the
ksz_dev_ops::phy_r() and ksz_dev_ops::phy_w() operations directly to
dsa_switch_ops.
Remove the now unused phy_r()/phy_w() callbacks from ksz_dev_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-8-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz_sw_mdio_read() and ksz_sw_mdio_write() respectively call
ksz_dev_ops::phy_r() and ksz_dev_ops::phy_w() just like
dsa_switch_ops::phy_read() and dsa_switch_ops::phy_write() do.
Call dsa_switch_ops::phy_read() from ksz_sw_mdio_read() and
dsa_switch_ops::phy_write() from ksz_sw_mdio_write() so we'll be able
to get rid of the useless indirections provided by ksz_dev_ops in
upcoming patch.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-7-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
port_setup() is handled through a common function that redirects
the treatment to ksz_dev_ops callbacks. This layer of indirection
isn't needed since we now have a dsa_switch_ops for each switch family
Remove one indirection layer for KSZ switches, by connecting the
ksz_dev_ops :: port_setup() operations directly to dsa_switch_ops.
Make ksz9477_set_default_prio_queue_mapping() non-static since it's used
by ksz_common for tc operations and by ksz9477.c for this port_setup().
Remove the now unused port_setup() callback from ksz_dev_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-6-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All switch families have been converted to have their own
ds->ops->setup() methods and to call the common ksz_teardown().
Remove the no longer used ksz_setup() function and the associated
ksz_dev_ops callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-5-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The KSZ switch families are sufficiently different that a common
ds->ops->setup() - ksz_setup() with micro-managed dev_ops->reset(),
dev_ops->pcs_create(), dev_ops->config_cpu_port(),
dev_ops->enable_stp_addr(), dev_ops->setup() seems to be too convoluted.
I am proposing to make each KSZ switch family part ways for
dsa_switch_ops :: setup() and teardown(), to allow them greater
flexibility. This here is the implementation for ksz8, which is
nothing other than a copy of ksz_setup() with the dev_ops function
pointers replaced with direct function calls.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-4-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The KSZ switch families are sufficiently different that a common
ds->ops->setup() - ksz_setup() with micro-managed dev_ops->reset(),
dev_ops->pcs_create(), dev_ops->config_cpu_port(),
dev_ops->enable_stp_addr(), dev_ops->setup() seems to be too convoluted.
I am proposing to make each KSZ switch family part ways for
dsa_switch_ops :: setup() and teardown(), to allow them greater
flexibility. This here is the implementation for ksz9477, which is
nothing other than a copy of ksz_setup() with the dev_ops function
pointers replaced with direct function calls.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-3-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The KSZ switch families are sufficiently different that a common
ds->ops->setup() - ksz_setup() with micro-managed dev_ops->reset(),
dev_ops->pcs_create(), dev_ops->config_cpu_port(),
dev_ops->enable_stp_addr(), dev_ops->setup() seems to be too convoluted.
I am proposing to make each KSZ switch family part ways for
dsa_switch_ops :: setup() and teardown(), to allow them greater
flexibility. This here is the implementation for lan937x, which is
nothing other than a copy of ksz_setup() with the dev_ops function
pointers replaced with direct function calls.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-2-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ksz_switch driver is one of the few which reset the switch when
unbinding the driver or shutting down - in the same category with
ar9331_sw_remove(), bcm_sf2_sw_remove(), and ks8995_remove(),
vsc73xx_remove() and lan9303_remove().
I don't think there exists any requirement to do this, and in fact it
does create complications for WoL, as the code already shows.
My issue with this logic is that it is the only thing keeping
dev_ops->reset() necessary, which I would like to remove after
individual KSZ switch families get their own setup() and teardown()
methods that don't go through dev_ops.
Don't reset the switch when unbinding the driver or shutting down.
Remove the exit callbacks from the ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260521-clean-ksz-2nd-series-v3-1-75c38971c19a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
While touching these arrays, unify usage of whitespace in the list
terminator.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260519145722.1590298-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz_phylink_get_caps() is a bit different from other generic methods.
It has a dev_ops->get_caps() call in the middle of the function, and it
does other stuff before (set some supported_interfaces) and after (set
lpi_interfaces from supported_interfaces).
Whereas the dev_ops->get_caps() methods set mac_capabilities and
(optionally) logically OR the supported_interfaces with that of the PCS.
The idea is that this can be expressed simpler, and avoid a indirect
function call to dev_ops->get_caps(). If we tail-call the common
ksz_phylink_get_caps() from individual phylink_get_caps() methods, we do
reorder the settings, but in an inconsequential way (the transfer from
supported_interfaces to lpi_interfaces still sees a complete list of the
supported_interfaces).
Remove the no longer used get_caps() callbacl the ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-7-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mirror operations are handled through a common function that redirects
the treatment to ksz_dev_ops callbacks. This layer of indirection isn't
needed since we now have a dsa_switch_ops for each switch family.
Remove this indirection layer for KSZ switches, by connecting the
ksz_dev_ops :: mirror_add() and mirror_del() operations directly to
dsa_switch_ops.
Remove the now unused mirror callbacks from ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-6-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FDB and MDB operations are handled through a common function that
redirects the treatment to ksz_dev_ops callbacks. This layer of
indirection isn't needed since we now have a dsa_switch_ops for each kind
of switch.
Remove one indirection layer for KSZ switches, by connecting the
ksz_dev_ops :: fdb_dump(), fdb_add(), fdb_del(), mdb_add() and mdb_del()
operations directly to dsa_switch_ops.
Remove the FDB and MDB operations from ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-5-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VLAN operations are handled through a common function that redirects the
treatment to ksz_dev_ops callbacks. This level of indirection isn't
needed since we now have a dsa_switch_ops for each kind of switch.
Remove this useless layer of indirection by connecting directly the VLAN
operations to the relevant dsa_switch_ops.
Adapt their prototypes to match dsa_switch_ops expectations.
Remove the now unused VLAN callbacks from ksz_dev_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-4-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MTU changing is done through a common function that redirects the
treatment to a specific ksz_dev_ops callback. This layer of indirection
isn't needed since we now have a dsa_switch_ops struct for each switch
family.
Remove this indirection layer in MTU changing for KSZ switches, by
directly connecting the ksz_dev_ops :: change_mtu() implementations to
dsa_switch_ops.
Remove the no longer used change_mtu() callback from ksz_dev_ops
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-3-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dsa_switch_ops :: set_ageing_time() goes through ksz_set_ageing_time(),
further dispatched through ksz_dev_ops :: set_ageing_time(). Only
ksz9477 and lan937x provide an implementation for this, so remove the
(optional) method from ksz8463_switch_ops, ksz87xx_switch_ops,
ksz88xx_switch_ops. Also, hook up ksz9477 and lan937x dsa_switch_ops
directly to their respective implementations.
Every switch family provides a dsa_switch_ops :: port_fast_age()
implementation, which is dispatched through ksz_dev_ops ::
flush_dyn_mac_table(). Remove the dev_ops indirection and connect the
flush_dyn_mac_table() methods directly to their respective dsa_switch_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-2-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz_dev_ops::phylink_mac_link_up() isn't used anywhere.
Remove it.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260512-clean-ksz-2nd-series-v1-1-c00f6ce037fa@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
