| Age | Commit message (Collapse) | Author |
|---|
|
This is a residual of the $FreeBSD$ removal.
MFC After: 3 days (though I'll just run the command on the branches)
Sponsored by: Netflix
|
|
Remove /^\s*#[#!]?\s*\$FreeBSD\$.*$\n/
|
|
Remove all sparc64 specific files
Remove all sparc64 ifdefs
Removee indireeect sparc64 ifdefs
Notes:
svn path=/head/; revision=357455
|
|
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
Notes:
svn path=/head/; revision=332122
|
|
MFC with: r330876
Notes:
svn path=/head/; revision=330945
|
|
This simplifies make output/logic
Tested with: `cd sys/modules; make ALL_MODULES=` on amd64
MFC after: 1 month
Sponsored by: Dell EMC Isilon
Notes:
svn path=/head/; revision=314651
|
|
which are also likely to be irrelevant for sun4v (there's no SBus on sun4v
and only some EBus devices). While at it fix some style bugs according to
style.Makefile(5) where appropriate.
MFC after: 3 days
Notes:
svn path=/head/; revision=178762
|
|
Notes:
svn path=/head/; revision=165067
|
|
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
Notes:
svn path=/head/; revision=133589
|
|
pci support is always compiled in.
Notes:
svn path=/head/; revision=106260
|
