| Age | Commit message (Collapse) | Author |
|---|
|
The mesh interface can use a distributed hash table to answer ARP requests
without flooding the request through the whole mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_DISTRIBUTED_ARP_TABLE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can try to detect loops in the same mesh caused by
(indirectly) bridged mesh/soft-interfaces of different nodes. Some of the
loops can also be resolved without breaking the mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can use multiple slave/hard-interface ports at the same
time to transport the traffic to other nodes.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_BONDING_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can drop messages between clients to implement a
mesh-wide AP isolation.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH and
BATADV_CMD_SET_VLAN/BATADV_CMD_GET_VLAN commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AP_ISOLATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
This feature also requires that skbuff which should be handled as isolated
are marked. The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to
set/get the mark/mask using the u32 attributes BATADV_ATTR_ISOLATION_MARK
and BATADV_ATTR_ISOLATION_MASK.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The mesh interface can delay OGM messages to aggregate different ogms
together in a single OGM packet.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AGGREGATED_OGMS_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the VLANs on top of
the mesh/soft-interface have configuration settings. The genl interface
reflects this by allowing to get/set it using the vlan specific commands
BATADV_CMD_GET_VLAN/BATADV_CMD_SET_VLAN.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_VLAN command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the
slave/hard-interface have B.A.T.M.A.N. V specific configuration settings.
The genl interface reflects this by allowing to get/set it using the
hard-interface specific commands.
The BATADV_CMD_GET_HARDIFS (or short version BATADV_CMD_GET_HARDIF) is
reused as get command because it already allow sto dump the content of
other information from the slave/hard-interface which are not yet
configuration specific.
The set command BATADV_CMD_SET_HARDIF will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_HARDIF
command message type that settings might have been changed and what the
current values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
The main objects for this configuration is the mesh/soft-interface object.
Its actual object in memory already contains most of the available
configuration settings. The genl interface reflects this by allowing to
get/set it using the mesh specific commands.
The BATADV_CMD_GET_MESH_INFO (or short version BATADV_CMD_GET_MESH) is
reused as get command because it already provides the content of other
information from the mesh/soft-interface which are not yet configuration
specific.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_MESH command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
checkpatch.pl complains since commit 45e417022023 ("scripts/spelling.txt:
add more spellings to spelling.txt") about an additional spelling mistake
in batman-adv:`
CHECK: 'reseved' may be misspelled - perhaps 'reserved'?
#232: FILE: include/uapi/linux/batadv_packet.h:232:
+ * @flags: reseved for routing relevant flags - currently always 0
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Bit 0 in register 1.5 doesn't represent a device but is a flag that
Clause 22 registers are present. Therefore disregard this bit when
populating the device list. If code needs this information it
should read register 1.5 directly instead of accessing the device
list.
Because this bit doesn't represent a device don't define a
MDIO_MMD_XYZ constant, just define a MDIO_DEVS_XYZ constant for
the flag in the device list bitmap.
v2:
- make masking of bit 0 more explicit
- improve commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let genphy_c45_read_link manage the devices to check, this removes
overhead from callers. Add C22EXT to the list of excluded devices
because it doesn't implement the status register. According to the
802.3 clause 45 spec registers 29.0 - 29.4 are reserved.
At the moment we have very few clause 45 PHY drivers, so we are
lacking experience whether other drivers will have to exclude further
devices, or may need to check PHY XS. If we should figure out that
list of devices to check needs to be configurable, I think best will
be to add a device list member to struct phy_driver.
v2:
- adjusted commit message
- exclude also device C22EXT from link checking
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink fmsg is a mechanism to pass descriptors between drivers and
devlink, in json-like format. The API allows the driver to add nested
attributes such as object, object pair and value array, in addition to
attributes such as name and value.
Driver can use this API to fill the fmsg context in a format which will be
translated by the devlink to the netlink message later.
There is no memory allocation in advance (other than the initial list
head), and it dynamically allocates messages descriptors and add them to
the list on the fly.
When it needs to send the data using SKBs to the netlink layer, it
fragments the data between different SKBs. In order to do this
fragmentation, it uses virtual nests attributes, to avoid actual
nesting use which cannot be divided between different SKBs.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for events with data type FSNOTIFY_EVENT_INODE
(e.g. create/attrib/move/delete) for inode and filesystem mark types.
The "inode" events do not carry enough information (i.e. path) to
report event->fd, so we do not allow setting a mask for those events
unless group supports reporting fid.
The "inode" events are not supported on a mount mark, because they do
not carry enough information (i.e. path) to be filtered by mount point.
The "dirent" events (create/move/delete) report the fid of the parent
directory where events took place without specifying the filename of the
child. In the future, fanotify may get support for reporting filename
information for those events.
Cc: <linux-api@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
If group requested FAN_REPORT_FID and event has file identifier,
copy that information to user reading the event after event metadata.
fid information is formatted as struct fanotify_event_info_fid
that includes a generic header struct fanotify_event_info_header,
so that other info types could be defined in the future using the
same header.
metadata->event_len includes the length of the fid information.
The fid information includes the filesystem's fsid (see statfs(2))
followed by an NFS file handle of the file that could be passed as
an argument to open_by_handle_at(2).
Cc: <linux-api@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
When user requests the flag FAN_REPORT_FID in fanotify_init(),
a unique file identifier of the event target object will be reported
with the event.
The file identifier includes the filesystem's fsid (i.e. from statfs(2))
and an NFS file handle of the file (i.e. from name_to_handle_at(2)).
The file identifier makes holding the path reference and passing a file
descriptor to user redundant, so those are disabled in a group with
FAN_REPORT_FID.
Encode fid and store it in event for a group with FAN_REPORT_FID.
Up to 12 bytes of file handle on 32bit arch (16 bytes on 64bit arch)
are stored inline in fanotify_event struct. Larger file handles are
stored in an external allocated buffer.
On failure to encode fid, we print a warning and queue the event
without the fid information.
[JK: Fold part of later patched into this one to use
exportfs_encode_inode_fh() right away]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Pull virtio fixes from Michael Tsirkin:
"A small fix for a uapi header, and a fix for VDPA for non-x86 guests"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: drop internal struct from UAPI
virtio: support VIRTIO_F_ORDER_PLATFORM
|
|
We now use 64-bit time_t on all architectures, so the __kernel_timex,
__kernel_timeval and __kernel_timespec redirects can be removed
after having served their purpose.
This makes it all much less confusing, as the __kernel_* types
now always refer to the same layout based on 64-bit time_t across
all 32-bit and 64-bit architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
struct timex uses struct timeval internally.
struct timeval is not y2038 safe.
Introduce a new UAPI type struct __kernel_timex
that is y2038 safe.
struct __kernel_timex uses a timeval type that is
similar to struct __kernel_timespec which preserves the
same structure size across 32 bit and 64 bit ABIs.
struct __kernel_timex also restructures other members of the
structure to make the structure the same on 64 bit and 32 bit
architectures.
Note that struct __kernel_timex is the same as struct timex
on a 64 bit architecture.
The above solution is similar to other new y2038 syscalls
that are being introduced: both 32 bit and 64 bit ABIs
have a common entry, and the compat entry supports the old 32 bit
syscall interface.
Alternatives considered were:
1. Add new time type to struct timex that makes use of padded
bits. This time type could be based on the struct __kernel_timespec.
modes will use a flag to notify which time structure should be
used internally.
This needs some application level changes on both 64 bit and 32 bit
architectures. Although 64 bit machines could continue to use the
older timeval structure without any changes.
2. Add a new u8 type to struct timex that makes use of padded bits. This
can be used to save higher order tv_sec bits. modes will use a flag to
notify presence of such a type.
This will need some application level changes on 32 bit architectures.
3. Add a new compat_timex structure that differs in only the size of the
time type; keep rest of struct timex the same.
This requires extra syscalls to manage all 3 cases on 64 bit
architectures. This will not need any application level changes but will
add more complexity from kernel side.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There's no reason to expose struct vring_packed in UAPI - if we do we
won't be able to change or drop it, and it's not part of any interface.
Let's move it to virtio_ring.c
Cc: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
RDS Service type (TOS) is user-defined and needs to be configured
via RDS IOCTL interface. It must be set before initiating any
traffic and once set the TOS can not be changed. All out-going
traffic from the socket will be associated with its TOS.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
[yanjun.zhu@oracle.com: Adapted original patch with ipv6 changes]
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
|
|
nft "tunnel" expr match both the tun_info of RX and TX. This patch
provide the NFTA_TUNNEL_MODE to individually match the tun_info of
RX or TX.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanup for IIO in the 5.1 cycle
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
* tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (67 commits)
iio: chemical: sps30: remove printk format specifier
staging: iio: frequency: ad9833: Load clock using clock framework
staging: iio: frequency: ad9833: Get frequency value statically
dt-bindings: iio: light: Add max44009
iio: light: add driver for MAX44009
dt-bindings: iio: adc: Add docs for AD7768-1
iio: adc: Add AD7768-1 ADC basic support
staging: iio: cdc: ad7152: remove driver completely
iio: imu: mpu6050: Add support for the ICM 20602 IMU
dt-bindings: iio: imu: add icm20602 bindings to mpu6050
dt-bindings: iio: pressure: add LPS22HH bindings
iio: st_accel: use ACPI orientation data
iio: adc: add NPCM ADC driver
dt-binding: iio: add NPCM ADC documentation
iio: chemical: sps30: allow changing self cleaning period
dt-bindings: iio: chemical: Add bindings for bme680
iio: chemical: bme680: Add device-tree support
iio:st_pressure:initial lps22hh sensor support
iio: accell: mma8452: add vdd/vddio regulator operation support
dt-bindings: iio: accel: mma8452: add power supplies property
...
|
|
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SO_TIMESTAMPING_NEW variant of socket timestamp options.
This is the y2038 safe versions of the SO_TIMESTAMPING_OLD
for all architectures.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: chris@zankel.net
Cc: fenghua.yu@intel.com
Cc: rth@twiddle.net
Cc: tglx@linutronix.de
Cc: ubraun@linux.ibm.com
Cc: linux-alpha@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-s390@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new type is meant to be used as a y2038 safe structure
to be used as part of cmsg data.
Presently the SO_TIMESTAMP socket option uses struct timeval
for timestamps. This is not y2038 safe.
Subsequent patches in the series add new y2038 safe socket
option to be used in the place of SO_TIMESTAMP_OLD.
struct __kernel_sock_timeval will be used as the timestamp
format at that time.
struct __kernel_sock_timeval also maintains the same layout
across 32 bit and 64 bit ABIs.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct __kernel_old_timeval is supposed to have the same
layout as struct timeval. But, it was inadvarently missed
that __kernel_suseconds has a different definition for
sparc64.
Provide an asm-specific override that fixes it.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-01
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) introduce bpf_spin_lock, from Alexei.
2) convert xdp samples to libbpf, from Maciej.
3) skip verifier tests for unsupported program/map types, from Stanislav.
4) powerpc64 JIT support for BTF line info, from Sandipan.
5) assorted fixed, from Valdis, Jesper, Jiong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool -i has a few fixed-size fields which can be used to report
firmware version and expansion ROM version. Unfortunately, modern
hardware has more firmware components. There is usually some
datapath microcode, management controller, PXE drivers, and a
CPLD load. Running ethtool -i on modern controllers reveals the
fact that vendors cram multiple values into firmware version field.
Here are some examples from systems I could lay my hands on quickly:
tg3: "FFV20.2.17 bc 5720-v1.39"
i40e: "6.01 0x800034a4 1.1747.0"
nfp: "0.0.3.5 0.25 sriov-2.1.16 nic"
Add a new devlink API to allow retrieving multiple versions, and
provide user-readable name for those versions.
While at it break down the versions into three categories:
- fixed - this is the board/fixed component version, usually vendors
report information like the board version in the PCI VPD,
but it will benefit from naming and common API as well;
- running - this is the running firmware version;
- stored - this is firmware in the flash, after firmware update
this value will reflect the flashed version, while the
running version may only be updated after reboot.
v3:
- add per-type helpers instead of using the special argument (Jiri).
RFCv2:
- remove the nesting in attr DEVLINK_ATTR_INFO_VERSIONS (now
versions are mixed with other info attrs)l
- have the driver report versions from the same callback as
other info.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool -i has served us well for a long time, but its showing
its limitations more and more. The device information should
also be reported per device not per-netdev.
Lay foundation for a simple devlink-based way of reading device
info. Add driver name and device serial number as initial pieces
of information exposed via this new API.
v3:
- rename helpers (Jiri);
- rename driver name attr (Jiri);
- remove double spacing in commit message (Jiri).
RFC v2:
- wrap the skb into an opaque structure (Jiri);
- allow the serial number of be any length (Jiri & Andrew);
- add driver name (Jonathan).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS 1.3 has minor changes from TLS 1.2 at the record layer.
* Header now hardcodes the same version and application content type in
the header.
* The real content type is appended after the data, before encryption (or
after decryption).
* The IV is xored with the sequence number, instead of concatinating four
bytes of IV with the explicit IV.
* Zero-padding: No exlicit length is given, we search backwards from the
end of the decrypted data for the first non-zero byte, which is the
content type. Currently recv supports reading zero-padding, but there
is no way for send to add zero padding.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wire up support for 256 bit keys from the setsockopt to the crypto
framework
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce BPF_F_LOCK flag for map_lookup and map_update syscall commands
and for map_update() helper function.
In all these cases take a lock of existing element (which was provided
in BTF description) before copying (in or out) the rest of map value.
Implementation details that are part of uapi:
Array:
The array map takes the element lock for lookup/update.
Hash:
hash map also takes the lock for lookup/update and tries to avoid the bucket lock.
If old element exists it takes the element lock and updates the element in place.
If element doesn't exist it allocates new one and inserts into hash table
while holding the bucket lock.
In rare case the hashmap has to take both the bucket lock and the element lock
to update old value in place.
Cgroup local storage:
It is similar to array. update in place and lookup are done with lock taken.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Introduce 'struct bpf_spin_lock' and bpf_spin_lock/unlock() helpers to let
bpf program serialize access to other variables.
Example:
struct hash_elem {
int cnt;
struct bpf_spin_lock lock;
};
struct hash_elem * val = bpf_map_lookup_elem(&hash_map, &key);
if (val) {
bpf_spin_lock(&val->lock);
val->cnt++;
bpf_spin_unlock(&val->lock);
}
Restrictions and safety checks:
- bpf_spin_lock is only allowed inside HASH and ARRAY maps.
- BTF description of the map is mandatory for safety analysis.
- bpf program can take one bpf_spin_lock at a time, since two or more can
cause dead locks.
- only one 'struct bpf_spin_lock' is allowed per map element.
It drastically simplifies implementation yet allows bpf program to use
any number of bpf_spin_locks.
- when bpf_spin_lock is taken the calls (either bpf2bpf or helpers) are not allowed.
- bpf program must bpf_spin_unlock() before return.
- bpf program can access 'struct bpf_spin_lock' only via
bpf_spin_lock()/bpf_spin_unlock() helpers.
- load/store into 'struct bpf_spin_lock lock;' field is not allowed.
- to use bpf_spin_lock() helper the BTF description of map value must be
a struct and have 'struct bpf_spin_lock anyname;' field at the top level.
Nested lock inside another struct is not allowed.
- syscall map_lookup doesn't copy bpf_spin_lock field to user space.
- syscall map_update and program map_update do not update bpf_spin_lock field.
- bpf_spin_lock cannot be on the stack or inside networking packet.
bpf_spin_lock can only be inside HASH or ARRAY map value.
- bpf_spin_lock is available to root only and to all program types.
- bpf_spin_lock is not allowed in inner maps of map-in-map.
- ld_abs is not allowed inside spin_lock-ed region.
- tracing progs and socket filter progs cannot use bpf_spin_lock due to
insufficient preemption checks
Implementation details:
- cgroup-bpf class of programs can nest with xdp/tc programs.
Hence bpf_spin_lock is equivalent to spin_lock_irqsave.
Other solutions to avoid nested bpf_spin_lock are possible.
Like making sure that all networking progs run with softirq disabled.
spin_lock_irqsave is the simplest and doesn't add overhead to the
programs that don't use it.
- arch_spinlock_t is used when its implemented as queued_spin_lock
- archs can force their own arch_spinlock_t
- on architectures where queued_spin_lock is not available and
sizeof(arch_spinlock_t) != sizeof(__u32) trivial lock is used.
- presence of bpf_spin_lock inside map value could have been indicated via
extra flag during map_create, but specifying it via BTF is cleaner.
It provides introspection for map key/value and reduces user mistakes.
Next steps:
- allow bpf_spin_lock in other map types (like cgroup local storage)
- introduce BPF_F_LOCK flag for bpf_map_update() syscall and helper
to request kernel to grab bpf_spin_lock before rewriting the value.
That will serialize access to map elements.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Add DHCPACKs for DAT snooping, by Linus Luessing
- Update copyright years for 2019, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new ptrace regsets, which can be used to request and change the
pointer authentication keys of a thread. NT_ARM_PACA_KEYS gives access
to the instruction/data address keys, and NT_ARM_PACG_KEYS to the
generic authentication key. The keys are also part of the core dump file
of the process.
The regsets are only exposed if the kernel is compiled with
CONFIG_CHECKPOINT_RESTORE=y, as the only intended use case is
checkpointing and restoring processes that are using pointer
authentication. (This can be changed later if there are other use
cases.)
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch is to add 3 constants SCTP_FUTURE_ASSOC,
SCTP_CURRENT_ASSOC and SCTP_ALL_ASSOC for reserved
assoc_ids, as defined in rfc6458#section-7.2.
And add the process for them when doing lookup and
inserting in sctp_id2assoc and sctp_assoc_set_id.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tegra Combined UART (TCU) is a mailbox-based mechanism that allows
multiplexing multiple "virtual UARTs" into a single hardware serial
port. The TCU is the primary serial port on Tegra194 devices.
Add a TCU driver utilizing the mailbox framework, as the used mailboxes
are part of Tegra HSP blocks that are already controlled by the Tegra
HSP mailbox driver.
Based on work by Mikko Perttunen <mperttunen@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add notification call for devlink port param set, register and unregister
functions.
Add devlink_port_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
v7->v8:
Order devlink_port_param_value_changed() definitions followed by
devlink_param_value_changed()
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add port param set command to set the value for a parameter.
Value can be set to any of the supported configuration modes.
v7->v8: Append "Acked-by: Jiri Pirko <jiri@mellanox.com>"
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add port param get command which gets data per parameter.
It also has option to dump the parameters data per port.
v7->v8: Append "Acked-by: Jiri Pirko <jiri@mellanox.com>"
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Hyper-V _DSM command set to the white list of NVDIMM command
sets.
This command set is documented at http://www.uefi.org/RFIC_LIST
(see "Virtual NVDIMM 0x1901").
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
With the default SPEC_STORE_BYPASS_SECCOMP/SPEC_STORE_BYPASS_PRCTL mode,
the TIF_SSBD bit will be inherited when a new task is fork'ed or cloned.
It will also remain when a new program is execve'ed.
Only certain class of applications (like Java) that can run on behalf of
multiple users on a single thread will require disabling speculative store
bypass for security purposes. Those applications will call prctl(2) at
startup time to disable SSB. They won't rely on the fact the SSB might have
been disabled. Other applications that don't need SSBD will just move on
without checking if SSBD has been turned on or not.
The fact that the TIF_SSBD is inherited across execve(2) boundary will
cause performance of applications that don't need SSBD but their
predecessors have SSBD on to be unwittingly impacted especially if they
write to memory a lot.
To remedy this problem, a new PR_SPEC_DISABLE_NOEXEC argument for the
PR_SET_SPECULATION_CTRL option of prctl(2) is added to allow applications
to specify that the SSBD feature bit on the task structure should be
cleared whenever a new program is being execve'ed.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: https://lkml.kernel.org/r/1547676096-3281-1-git-send-email-longman@redhat.com
|
