| Age | Commit message (Collapse) | Author |
|---|
|
Rename the inner 'frm' variable to 'resp_frm' in the write path of
mmc_route_rpmb_frames() to avoid shadowing the outer 'frm' variable.
The function declares 'frm' at function scope pointing to the request
frame, but then redeclares another 'frm' variable inside the write
block pointing to the response frame. This shadowing makes the code
confusing and error-prone.
Using 'resp_frm' for the response frame makes the distinction clear
and improves code readability.
Fixes: 7852028a35f0 ("mmc: block: register RPMB partition with the RPMB subsystem")
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
power-on
According to the power structure of IC hardware design for UHS-II
interface, reset control and timing must be added to the initialization
process of powering on the UHS-II interface.
Fixes: 27dd3b82557a ("mmc: sdhci-pci-gli: enable UHS-II mode for GL9767")
Cc: stable@vger.kernel.org # v6.13+
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix calling incorrect sdhci_set_clock() in __sdhci_uhs2_set_ios() when the
vendor defines its own sdhci_set_clock().
Fixes: 10c8298a052b ("mmc: sdhci-uhs2: add set_ios()")
Cc: stable@vger.kernel.org # v6.13+
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_set_ios_common() into sdhci_set_ios()
The sdhci_set_clock() is called in sdhci_set_ios_common() and
__sdhci_uhs2_set_ios(). According to Section 3.13.2 "Card Interface
Detection Sequence" of the SD Host Controller Standard Specification
Version 7.00, the SD clock is supplied after power is supplied, so we only
need one in __sdhci_uhs2_set_ios(). Let's move the code related to setting
the clock from sdhci_set_ios_common() into sdhci_set_ios() and modify
the parameters passed to sdhci_set_clock() in __sdhci_uhs2_set_ios().
Fixes: 10c8298a052b ("mmc: sdhci-uhs2: add set_ios()")
Cc: stable@vger.kernel.org # v6.13+
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Introduce a new device tree flag to cap the maximum High-Speed (HS)
mode frequency for SD cards, accommodating board-specific
electrical limitations which cannot support the default 50Mhz HS
frequency and others.
Signed-off-by: Sarthak Garg <quic_sartgarg@quicinc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For Qualcomm SoCs which needs level shifter for SD card, extra delay is
seen on receiver data path.
To compensate this delay enable tuning for SDR50 mode for targets which
has level shifter. SDHCI_SDR50_NEEDS_TUNING caps will be set for targets
with level shifter on Qualcomm SOC's.
Signed-off-by: Sarthak Garg <quic_sartgarg@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Merge the pmdomain fixes for v6.17-rc[n] into the next branch, to allow
them to get tested together with the new changes that are targeted for
v6.18.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
At the moment the driver sets the power state of all the PDs it creates
to off, regardless of the actual HW state. This has two drawbacks:
1) The kernel cannot disable unused PDs automatically for power saving,
as it thinks they are off already
2) A more specific case (but perhaps applicable to other scenarios
also): bootloader enabled splash-screen cannot be kept on the screen.
The issue in 2) is that the driver framework automatically enables the
device's PD before calling probe() and disables it after the probe().
This means that when the display subsystem (DSS) driver probes, but e.g.
fails due to deferred probing, the DSS PD gets turned off and the driver
cannot do anything to affect that.
Solving the 2) requires more changes to actually keep the PD on during
the boot, but a prerequisite for it is to have the correct power state
for the PD.
The downside with this patch is that it takes time to call the 'is_on'
op, and we need to call it for each PD. In my tests with AM62 SK, using
defconfig, I see an increase from ~3.5ms to ~7ms. However, the added
feature is valuable, so in my opinion it's worth it.
The performance could probably be improved with a new firmware API which
returns the power states of all the PDs.
There's also a related HW issue at play here: if the DSS IP is enabled
and active, and its PD is turned off without first disabling the DSS
display outputs, the DSS IP will hang and causes the kernel to halt if
and when the DSS driver accesses the DSS registers the next time.
With the current upstream kernel, with this patch applied, this means
that if the bootloader enables the display, and the DSS driver is
compiled as a module, the kernel will at some point disable unused PDs,
including the DSS PD. When the DSS module is later loaded, it will hang
the kernel.
The same issue is already there, even without this patch, as the DSS
driver may hit deferred probing, which causes the PD to be turned off,
and leading to kernel halt when the DSS driver is probed again. This
issue has been made quite rare with some arrangements in the DSS
driver's probe, but it's still there.
With recent change from Ulf (e.g. commit 13a4b7fb6260 ("pmdomain: core:
Leave powered-on genpds on until late_initcall_sync")), the sync state
mechanism comes to rescue. It will keep the power domains enabled, until
the drivers have probed, or the sync-state is triggered via some other
mechanism (e.g. manually by the boot scripts).
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Print full device node name with %pOF format, so the code will be a bit
simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unassigned system sleep callbacks were always treated the same as dummy
callbacks that just return zero.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
usb-next
Guan-Yu Lin <guanyulin@google.com> says:
Wesley Cheng and Mathias Nyman's USB offload design enables a
co-processor to handle some USB transfers, potentially allowing the
system to sleep (suspend-to-RAM) and save power. However, Linux's System
Sleep model halts the USB host controller when the main system isn't
managing any USB transfers. To address this, the proposal modifies the
system to recognize offloaded USB transfers and manage power
accordingly. This way, offloaded USB transfers could still happen during
system sleep (Suspend-to-RAM).
This involves two key steps:
1. Transfer Status Tracking: Propose offload_usage and corresponding
apis drivers could track USB transfers on the co-processor, ensuring
the system is aware of any ongoing activity.
2. Power Management Adjustment: Modifications to the USB driver stack
(xhci host controller driver, and USB device drivers) allow the
system to sleep (Suspend-to-RAM) without disrupting co-processor
managed USB transfers. This involves adding conditional checks to
bypass some power management operations in the System Sleep model.
Link: https://lore.kernel.org/r/20250911142051.90822-1-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sharing a USB controller with another entity via xhci-sideband driver
creates power management complexities. To prevent the USB controller
from being inadvertently deactivated while in use by the other entity, a
usage-count based mechanism is implemented. This allows the system to
manage power effectively, ensuring the controller remains available
whenever needed.
In order to maintain full functionality of an offloaded USB devices,
several changes are made within the suspend flow of such devices:
- skip usb_suspend_device() so that the port/hub are still active for
USB transfers via offloaded path.
- not suspending the endpoints which are used by USB interfaces marked
with needs_remote_wakeup. Namely, skip usb_suspend_interface() and
usb_hcd_flush_endpoint() on associated USB interfaces. This reserves a
pending interrupt urb during system suspend for handling the interrupt
transfer, which is necessary since remote wakeup doesn't apply in the
offloaded USB devices when controller is still active.
- not flushing the endpoints of actively offloaded USB devices. Given
that the USB devices is used by another entity, unilaterally flush the
endpoint might lead to unexpected behavior on another entity.
- not suspending the xhci controller. This is done by skipping the
suspend/resume callbacks in the xhci platform driver.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Link: https://lore.kernel.org/r/20250911142051.90822-5-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250911142051.90822-5-guanyulin@google.com
|
|
The existing sideband driver only registers sidebands without tracking
their active usage. To address this, sideband will now record its active
usage when it creates/removes interrupters. In addition, a new api is
introduced to provide a means for other dirvers to fetch sideband
activity information on a USB host controller.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Link: https://lore.kernel.org/r/20250911142051.90822-4-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250911142051.90822-4-guanyulin@google.com
|
|
Introduce offload_usage and corresponding apis to track offload usage
on each USB device. Offload denotes that there is another co-processor
accessing the USB device via the same USB host controller. To optimize
power usage, it's essential to monitor whether the USB device is
actively used by other co-processor. This information is vital when
determining if a USB device can be safely suspended during system power
state transitions.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Link: https://lore.kernel.org/r/20250911142051.90822-3-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250911142051.90822-3-guanyulin@google.com
|
|
Separate dev_pm_ops for different power events such as suspend, thaw,
and hibernation. This is crucial when xhci-plat driver needs to adapt
its behavior based on different power state changes.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Link: https://lore.kernel.org/r/20250911142051.90822-2-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250911142051.90822-2-guanyulin@google.com
|
|
Add a a driver for the I2C auxbus child device of the Intel USBIO USB
IO-expander used by the MIPI cameras on various new (Meteor Lake and
later) Intel laptops.
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Israel Cepeda <israel.a.cepeda.lopez@intel.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250911181343.77398-4-hansg@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a a driver for the GPIO auxbus child device of the Intel USBIO USB
IO-expander used by the MIPI cameras on various new (Meteor Lake and
later) Intel laptops.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Israel Cepeda <israel.a.cepeda.lopez@intel.com>
Link: https://lore.kernel.org/r/20250911181343.77398-3-hansg@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a driver for the Intel USBIO USB IO-expander used by the MIPI cameras
on various new (Meteor Lake and later) Intel laptops.
This is an USB bridge driver which adds auxbus child devices for the GPIO,
I2C and SPI functions of the USBIO chip and which exports IO-functions for
the drivers for the auxbus child devices to communicate with the USBIO
device's firmware.
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Israel Cepeda <israel.a.cepeda.lopez@intel.com>
Link: https://lore.kernel.org/r/20250911181343.77398-2-hansg@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v6.18 (take two)
- Improve suspend/resume support on RZ/G2L family SoCs,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The dma_unmap_sg() functions should be called with the same nents as the
dma_map_sg(), not the value the map function returned.
Fixes: 236caa7cc351 ("mmc: SDIO driver for Marvell SoCs")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On Qualcomm DWC3 dual-role controllers, the conndone/disconnect events in
device mode are generated by controller when software writes to QSCRATCH
registers in Qualcomm Glue layer rather than the vbus line being routed to
dwc3 core IP for it to recognize and generate these events.
UTMI_OTG_VBUS_VALID bit of QSCRATCH_HS_PHY_CTRL register needs to be set
to generate a connection done event and to be cleared for the controller to
generate a disconnect event during cable removal. When the disconnect is
not generated upon cable removal, the "connected" flag of dwc3 is left
marked as "true" and it blocks suspend routines and for that to happen upon
cable removal, the cable disconnect notification coming in via set_role
call need to be provided to the Qualcomm glue layer as well.
Currently, the way DWC3 core and Qualcomm legacy glue driver are designed,
there is no mechanism through which the DWC3 core can notify the Qualcomm
glue layer of any role changes which it receives via role switch. To
register these glue callbacks at probe time, for enabling core to notify
glue layer, the legacy Qualcomm driver has no way to find out when the
child driver probe was successful since it does not check for the same
during of_platform_populate.
Hence implement the following glue callbacks for flattened Qualcomm glue
driver:
1. set_role: To pass role switching information from drd layer to glue.
This information is needed to identify NONE/DEVICE mode switch and modify
QSCRATCH to generate connect-done event on device mode entry and disconnect
event on cable removal in device mode.
2. run_stop: When booting up in device mode, if autouspend is enabled and
userspace doesn't write UDC on boot, controller enters autosuspend. After
this, if the userspace writes to UDC in the future, run_stop notifier is
required to enable UTMI_OTG_VBUS_VALID of QSCRATCH so that connect done
event is generated after run_stop(1) is done to finish enumeration.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250907181412.2174616-3-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In certain situations like role switching, the glue layers need to be
informed of these events, so that they can take any necessary action.
But in non-flattened implementations, the glue drivers have no data on
when the core driver probe was successful post invoking of_platform_
populate. Now that the core driver supports flattened implementations
as well, introduce vendor callbacks that can be passed on from glue to
core before invoking dwc3_core_probe.
Introduce callbacks to notify glue layer of role_switch and run_stop
changes. These can be used by flattened implementation of Qualcomm
glue layer to generate connect/disconnect events in controller during
cable connect and run stop modifications by udc in device mode.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250907181412.2174616-2-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the system is suspended, USB hot-plugging/unplugging can trigger
wake events of the Tegra USB host controller.
Enable support for USB wake-up events by parsing device-tree to see if
the interrupts for the wake-up events are present and if so configure
those interrupts. Note that if wake-up events are not present, still
allow the USB host controller to probe as normal.
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20250811074558.1062048-5-haotienh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While the userspace program can be notified of gadget state changes,
timing issue can lead to missed transitions when reading the state
value.
Introduce a trace event for usb_gadget_set_state to reliably track state
transitions.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250818082722.2952867-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DWC2 IP can be properly integrated in a SoC to work at high-speed
USB speed but some board issues, EMC constraints or any other reasons
can lead to the need to limit this USB speed at board level.
The device-tree 'maximum-speed' property already exists for this purpose
but is not handled by the DWC2 driver.
Fill this lack adding support for 'maximum-speed' property and so allow
to limit the USB speed in device-tree (board description).
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20250910160730.585303-1-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add wakeup support for tcpci. If the user enables the wakeup file, call
enable_irq_wake() during system suspend and disable_irq_wake() during
system resume. Since this driver supports shared interrupts, mask the
chip interrupt by default when wakeup is disabled to avoid affecting
other IRQ users.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250910105042.695146-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v6.18
1. Add pin controller drivers for new Axis ARTPEC-8 SoC. The SoC shares
all main blocks, including the pin controller, with Samsung SoC, so
same drivers and bindings are used.
2. Drop remaining support for Samsung S3C2410 SoC pin controllers. The
actual SoC support was removed in January 2023, so this is just
remaining cleanup.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The buffer size of sysfs is fixed at PAGE_SIZE, and the page offset
of the buf parameter of sysfs_emit_at() must be 0, there is no need
to manually manage the buf pointer offset.
Fixes: 711d41ab4a0e ("usb: core: Use sysfs_emit_at() when showing dynamic IDs")
Reported-by: syzbot+b6445765657b5855e869@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b6445765657b5855e869
Tested-by: syzbot+b6445765657b5855e869@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Link: https://lore.kernel.org/r/tencent_B32D6D8C9450EBFEEE5ACC2C7B0E6C402D0A@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add interconnect dt-bindings and driver support for
Qualcomm's next gen compute SoC - Glymur.
* icc-glymur
dt-bindings: interconnect: document the RPMh Network-On-Chip interconnect in Glymur SoC
interconnect: qcom: icc-rpmh: increase MAX_PORTS to support four QoS ports
interconnect: qcom: add glymur interconnect provider driver
Link: https://lore.kernel.org/r/20250814-glymur-icc-v2-0-596cca6b6015@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Make use of device_match_of_node() instead of open coding its
functionality.
Signed-off-by: Zhang Enpei <zhang.enpei@zte.com.cn>
Link: https://lore.kernel.org/r/20250807141833927wb2idY1sZi1OpUKkrXk44@zte.com.cn
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
The mhi_ep_read_channel function incorrectly assumes the End of Transfer
(EOT) bit is present for each packet in a chained transactions, causing
it to advance mhi_chan->rd_offset beyond wr_offset during host-to-device
transfers when EOT has not yet arrived. This leads to access of unmapped
host memory, causing IOMMU faults and processing of stale TREs.
Modify the loop condition to ensure mhi_queue is not empty, allowing the
function to process only valid TREs up to the current write pointer to
prevent premature reads and ensure safe traversal of chained TREs.
Due to this change, buf_left needs to be removed from the while loop
condition to avoid exiting prematurely before reading the ring completely,
and also remove write_offset since it will always be zero because the new
cache buffer is allocated every time.
Fixes: 5301258899773 ("bus: mhi: ep: Add support for reading from the host")
Co-developed-by: Akhil Vinod <akhil.vinod@oss.qualcomm.com>
Signed-off-by: Akhil Vinod <akhil.vinod@oss.qualcomm.com>
Signed-off-by: Sumit Kumar <sumit.kumar@oss.qualcomm.com>
[mani: reworded description slightly]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250910-final_chained-v3-1-ec77c9d88ace@oss.qualcomm.com
|
|
Print full device node name with %pOF format, so the code will be a bit
simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20250912092423.162497-2-krzysztof.kozlowski@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Use recently added macros to print tile-oriented messages.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20250909165941.31730-6-michal.wajdeczko@intel.com
|
|
We already have dedicated helper macros for printing GT-oriented
messages but we don't have any to print messages that are tile
oriented and we wrongly try to use plain drm or GT-oriented ones.
Add tile-oriented printk messages and to provide similar coverage
as we have with xe_assert() macros. Also add set of simple macros
for the top level xe_device, which we could easily tweak to include
extra device specific info if needed.
Typical output of our printk macros will look like:
[drm] this is xe_WARN()
[drm] *ERROR* this is xe_err()
[drm] *ERROR* this is xe_err_printer()
[drm] this is xe_info()
[drm] this is xe_info_printer()
[drm:printk_demo.cold] this is xe_dbg()
[drm:printk_demo.cold] this is xe_dbg_printer()
[drm] Tile0: this is xe_tile_WARN()
[drm] *ERROR* Tile0: this is xe_tile_err()
[drm] *ERROR* Tile0: this is xe_tile_err_printer()
[drm] Tile0: this is xe_tile_info()
[drm] Tile0: this is xe_tile_info_printer()
[drm:printk_demo.cold] Tile0: this is xe_tile_dbg()
[drm:printk_demo.cold] Tile0: this is xe_tile_dbg_printer()
[drm] Tile0: GT0: this is xe_gt_WARN()
[drm] *ERROR* Tile0: GT0: this is xe_gt_err()
[drm] *ERROR* Tile0: GT0: this is xe_gt_err_printer()
[drm] Tile0: GT0: this is xe_gt_info()
[drm] Tile0: GT0: this is xe_gt_info_printer()
[drm:printk_demo.cold] Tile0: GT0: this is xe_gt_dbg()
[drm:printk_demo.cold] Tile0: GT0: this is xe_gt_dbg_printer()
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250909165941.31730-5-michal.wajdeczko@intel.com
|
|
To avoid code duplication (and thus potential mistakes) and to
allow easier changes (if needed) of the prefix format of the
GT-oriented messages, prepare that prefix in dedicated macro.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250909165941.31730-4-michal.wajdeczko@intel.com
|
|
Those WARN messages will already include GT-specific "GT%u:" prefix
so there is no point to include additional "gt_" prefix.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250909165941.31730-3-michal.wajdeczko@intel.com
|
|
There is no need to keep them separated. No functional changes.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250909165941.31730-2-michal.wajdeczko@intel.com
|
|
Notify the MHI device's Execution Environment (EE) state via uevent,
enabling applications to receive real-time updates and take appropriate
actions based on the current state of MHI.
Signed-off-by: Vivek Pernamitta <quic_vpernami@quicinc.com>
[mani: Reworded subject, removed error print, fixed indentation]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20250912-b4-uevent_vdev_next-20250911-v2-1-89440407bf7e@quicinc.com
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB serial device ids for 6.17-rc6
Here are some new modem device ids.
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-6.17-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit Cinterion LE910C4-WWX new compositions
USB: serial: option: add Telit Cinterion FN990A w/audio compositions
|
|
Move waiting related utilities from i915_utils.h to separate new file
i915_wait_util.h. Clean up related includes.
Note: Many of the various wait macro usages could likely be refactored
to use poll_timeout_us().
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/431396ac8cdb3e2f4ff053a8933290289a66ce42.1757582214.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move list related utilities from i915_utils.h to separate new file
i915_list_util.h. Clean up related includes.
Note: Arguably none of this should exist in i915 in the first place. At
least isolate it better.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/d7526809735194137116682f37cfa126a6a87ec9.1757582214.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move timer related utilities from i915_utils.[ch] to separate new files
i915_timer_util.[ch]. Clean up related includes.
Note: Arguably none of this should exist in i915 in the first place. At
least isolate it better.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/0a83d9489626121dcefcd4c1a05317399b5708f3.1757582214.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move pointer related utilities from i915_utils.h to a separate new
i915_ptr_util.h header. Clean up related includes.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/3cd06aa2483e68f19401292e9d4c28bf2977fce5.1757582214.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The clock drivers for RZ/V2H and RZ/V2N are very similar.
Reduce the differences between them by:
- Moving and reformatting the PLLCM33_GEAR clock definitions,
- Replacing spaces by TABs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/2246d2263e8a24d1aaf653db2004cbf2263c9048.1757606097.git.geert+renesas@glider.be
|
|
Add USB3.0 clock and reset entries.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250909180803.140939-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
In case of krealloc_array() failure, the current error handling just
returns from the function without freeing the original array.
Fix this memory leak by freeing the original array.
Fixes: 6aa1754764901668 ("clk: renesas: cpg-mssr: Ignore all clocks assigned to non-Linux system")
Signed-off-by: Yuan CHen <chenyuan@kylinos.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250908012810.4767-1-chenyuan_fl@163.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
With all users of bgpio_init() converted to using the modernized generic
GPIO chip API, we can now move the gpio-mmio-specific fields out of
struct gpio_chip and into the dedicated struct gpio_generic_chip. To
that end: adjust the gpio-mmio driver to the new layout, update the
docs, etc.
The changes in gpio-mlxbf2.c and gpio-mpc8xxx.c are here and not in their
respective conversion commits because the former passes the address of
the generic chip's lock to the __releases() annotation and we cannot
really hide it while gpio-mpc8xxx.c accesses the shadow registers in a
driver-specific workaround and there's no reason to make them available
in a public API.
Also: drop the relevant task from TODO as it's now done.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250910-gpio-mmio-gpio-conv-part4-v2-15-f3d1a4c57124@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the driver to using the new generic GPIO chip interfaces from
linux/gpio/generic.h.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250910-gpio-mmio-gpio-conv-part4-v2-14-f3d1a4c57124@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the driver to using the new generic GPIO chip interfaces from
linux/gpio/generic.h.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250910-gpio-mmio-gpio-conv-part4-v2-13-f3d1a4c57124@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Convert the driver to using the new generic GPIO chip interfaces from
linux/gpio/generic.h.
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250910-gpio-mmio-gpio-conv-part4-v2-12-f3d1a4c57124@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
