| Age | Commit message (Collapse) | Author |
|---|
|
phy.
hibmcge driver uses fixed_phy to configure scenarios without PHY,
where the driver is always in a linked state. However,
there might be no link in hardware, so the np_link error
is detected in hbg_hw_adjust_link(), which can cause abnormal logs.
Therefore, in scenarios without a PHY, the driver no longer
checks the np_link status.
Fixes: 1d7cd7a9c69c ("net: hibmcge: support scenario without PHY")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20251025014642.265259-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
irq initialized with the macro HBG_ERR_IRQ_I will automatically
be re-enabled, whereas those initialized with the macro HBG_IRQ_I
will not be re-enabled.
Since the rx buf avl irq is initialized using the macro HBG_IRQ_I,
it needs to be actively re-enabled;
otherwise priv->stats.rx_fifo_less_empty_thrsld_cnt cannot be
correctly incremented.
Fixes: fd394a334b1c ("net: hibmcge: Add support for abnormal irq handling feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251025014642.265259-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LED registers on YT8531 are exactly same as YT8521, so simply
reuse yt8521_led_hw_* functions.
Tested on OrangePi R1 Plus LTS and Zero3.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jijie Shao<shaojijie@huawei.com>
Link: https://patch.msgid.link/20251026133652.1288732-1-cnsztl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the signal format of an associated output is not considered
during output pin registration. As a result, the driver registers output
pins that are disabled by the signal format configuration.
Fix this by calling zl3073x_output_pin_is_enabled() to check whether
a given output pin should be registered or not.
Fixes: 75a71ecc2412 ("dpll: zl3073x: Register DPLL devices and pins")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251027140912.233152-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a limit to the number of jobs that can be queued in a single
exec queue to avoid potential resource exhaustion.
A new field `job_cnt` is introduced in `struct xe_exec_queue` to
track the number of active DRM jobs, along with a maximum limit
`XE_MAX_JOB_COUNT_PER_EXEC_QUEUE` set to 1000.
If the job count exceeds this threshold, `xe_exec_ioctl()` now
returns `-EAGAIN` to signal that the caller should retry later.
A trace event is added to track when the limit is reached:
"xe_exec_queue_reach_max_job_count: dev=0000:03:00.0, job count
exceeded the maximum limit (1000) per exec queue. engine_class=0x3,
logical_mask=0x1, guc_id=2"
v3: add assert in xe_exec_queue_destroy that q->job_cnt is zero. (Matt)
v2 (Matt):
- add log to trace the limit is hit.
- Change max count from 0x1000 to 1000.
- Use atomic_t for job_cnt.
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20251027202118.3339905-2-shuicheng.lin@intel.com
|
|
ch_ipsec_xfrm_add_state() callback
In ch_ipsec_xfrm_add_state() there is not check of try_module_get
return value. It is very unlikely, but try_module_get() could return
false value, which could cause use-after-free error.
Conditions: The module count must be zero, and a module unload in
progress. The thread doing the unload is blocked somewhere.
Another thread makes a callback into the module for some request
that (for instance) would need to create a kernel thread.
It tries to get a reference for the thread.
So try_module_get(THIS_MODULE) is the right call - and will fail here.
This fix adds checking the result of try_module_get call
Fixes: 6dad4e8ab3ec ("chcr: Add support for Inline IPSec")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Link: https://patch.msgid.link/20251024161304.724436-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8224 can detect open pairs and short types (in same pair or some
other pair). The distance to this problem can be estimated. This is done
for each of the 4 pairs separately.
It is not meant to be run while there is an active link partner because
this interferes with the active test pulses.
Output with open 50 m cable:
Pair A code Open Circuit, source: TDR
Pair A, fault length: 51.79m, source: TDR
Pair B code Open Circuit, source: TDR
Pair B, fault length: 51.28m, source: TDR
Pair C code Open Circuit, source: TDR
Pair C, fault length: 50.46m, source: TDR
Pair D code Open Circuit, source: TDR
Pair D, fault length: 51.12m, source: TDR
Terminated cable:
Pair A code OK, source: TDR
Pair B code OK, source: TDR
Pair C code OK, source: TDR
Pair D code OK, source: TDR
Shorted cable (both short types are at roughly the same distance)
Pair A code Short to another pair, source: TDR
Pair A, fault length: 2.35m, source: TDR
Pair B code Short to another pair, source: TDR
Pair B, fault length: 2.15m, source: TDR
Pair C code OK, source: TDR
Pair D code Short within Pair, source: TDR
Pair D, fault length: 1.94m, source: TDR
Signed-off-by: Issam Hamdi <ih@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251024-rtl8224-cable-test-v1-1-e3cda89ac98f@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: postpone service task disabling
Przemek Kitszel says:
Move service task shutdown to the very end of driver teardown procedure.
This is needed (or at least beneficial) for all unwinding functions that
talk to FW/HW via Admin Queue (so, most of top-level functions, like
ice_deinit_hw()).
Most of the patches move stuff around (I believe it makes it much easier
to review/proof when kept separate) in preparation to defer stopping the
service task to the very end of ice_remove() (and other unwinding flows).
Then last patch fixes duplicate call to ice_init_hw() (actual, but
unlikely to encounter, so -next, given the size of the changes).
First patch is not much related, only by that it was developed together
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: remove duplicate call to ice_deinit_hw() on error paths
ice: move ice_deinit_dev() to the end of deinit paths
ice: extract ice_init_dev() from ice_init()
ice: move ice_init_pf() out of ice_init_dev()
ice: move udp_tunnel_nic and misc IRQ setup into ice_init_pf()
ice: ice_init_pf: destroy mutexes and xarrays on memory alloc failure
ice: move ice_init_interrupt_scheme() prior ice_init_pf()
ice: move service task start out of ice_init_pf()
ice: enforce RTNL assumption of queue NAPI manipulation
====================
Link: https://patch.msgid.link/20251024204746.3092277-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device-id-get and pin-id-get handlers were ignoring errors from
the find functions and sending empty replies instead of returning
error codes to userspace.
When dpll_device_find_from_nlattr() or dpll_pin_find_from_nlattr()
returned an error (e.g., -EINVAL for "multiple matches" or -ENODEV
for "not found"), the handlers checked `if (!IS_ERR(ptr))` and
skipped adding the device/pin handle to the message, but then still
sent the empty message as a successful reply.
This caused userspace tools to receive empty responses with id=0
instead of proper netlink errors with extack messages like
"multiple matches".
The bug is visible via strace, which shows the kernel sending TWO
netlink messages in response to a single request:
1. Empty reply (20 bytes, just header, no attributes):
recvfrom(3, [{nlmsg_len=20, nlmsg_type=dpll, nlmsg_flags=0, ...},
{cmd=0x7, version=1}], ...)
2. NLMSG_ERROR ACK with extack (because of NLM_F_ACK flag):
recvfrom(3, [{nlmsg_len=60, nlmsg_type=NLMSG_ERROR,
nlmsg_flags=NLM_F_CAPPED|NLM_F_ACK_TLVS, ...},
[{error=0, msg={...}},
[{nla_type=NLMSGERR_ATTR_MSG}, "multiple matches"]]], ...)
The C YNL library parses the first message, sees an empty response,
and creates a result object with calloc() which zero-initializes all
fields, resulting in id=0.
The Python YNL library parses both messages and displays the extack
from the second NLMSG_ERROR message.
Fix by checking `if (IS_ERR(ptr))` first and returning the error
code immediately, so that netlink properly sends only NLMSG_ERROR with
the extack message to userspace. After this fix, both C and Python
YNL tools receive only the NLMSG_ERROR and behave consistently.
This affects:
- DPLL_CMD_DEVICE_ID_GET: now properly returns error when multiple
devices match the criteria (e.g., same module-name + clock-id)
- DPLL_CMD_PIN_ID_GET: now properly returns error when multiple pins
match the criteria (e.g., same module-name)
Before fix:
$ dpll pin id-get module-name ice
0 (wrong - should be error, there are 17 pins with module-name "ice")
After fix:
$ dpll pin id-get module-name ice
Error: multiple matches
(correct - kernel reports the ambiguity via extack)
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251024190733.364101-1-poros@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
Next installment of the SDCA changes, hopefully the next series after
this should be the full class driver. It is worth noting this series has
a build dependency on a patch working its way through the PM/ACPI tree:
commit ac46f5b6c661 ("ACPICA: Add SoundWire File Table (SWFT) signature")
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm.git
But we can probably worry about that later, as normally there is a
reasonable amount of review on these SDCA series'.
This series broadly breaks down into 3 chunks, first there are several
changes to remove the assumption that the struct device used for SDCA
purposes represents the SoundWire slave. This is because the SDCA class
driver will be made of an auxiliary driver for each SDCA Function, thus
the SoundWire slave will be on the parent device for each individual
driver. Then there are patches to add support for UMP/FDL. And then
finally since the rest of the HID support is there and UMP was the last
missing part required a small patch to add a function to allow reporting
of HID events from SDCA devices.
|
|
Since 3D merge allows for larger modes to be supported across 2 layer
mixers, filter modes based on adjusted mode clock / 2 when 3d merge is
supported.
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Fixes: 62b7d6835288 ("drm/msm/dpu: Filter modes based on adjusted mode clock")
Signed-off-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/676353/
Link: https://lore.kernel.org/r/20250923-modeclk-fix-v2-1-01fcd0b2465a@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
YUV formats on this hardware needs scaling for chroma planes. However it
is not implemented for QSEED2 which breaks display pipeline if YUV format
is used (causing partial and corrupted output with PPDONE timeouts).
This patch temporarily disables YUV by switching affected sub-block to
RGB only format list.
Fixes: daf9a92daeb8 ("drm/msm/dpu: Add support for MSM8996")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/682061/
Link: https://lore.kernel.org/r/20251018-b4-dpu-fixes-v1-6-1852278064d0@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
UBWC-related register configuration for writeback is not implemented in
the driver yet but there aren't any checks for non-linear modifiers in
atomic_check. Thus when compressed framebuffer is attached to writeback
connector it will be filled with linear image data. This patch forbids
non-linear modifiers for writeback framebuffers until UBWC support for
writeback is properly implemented.
Fixes: 71174f362d67 ("drm/msm/dpu: move writeback's atomic_check to dpu_writeback.c")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681922/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-5-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
In _dpu_plane_setup_pixel_ext function instead of dividing just chroma
source resolution once (component 1 and 2), second component is divided
once more because src_w and src_h variable is reused between iterations.
Third component receives wrong source resolution too (from component 2).
To fix this introduce temporary variables for each iteration.
Fixes: dabfdd89eaa9 ("drm/msm/disp/dpu1: add inline rotation support for sc7280")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681921/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-4-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Scaling is not implemented for some type of scalers (QSEED2 and RGB) but
it was unintentionally re-enabled with change below. The remaining
condition in dpu_plane_atomic_check_pipe is not enough because it only
checks for length of scaler block (which is present). This patch adds a
additional check for setup_scaler operation.
Fixes: 8f15005783b8 ("drm/msm/dpu: move scaling limitations out of the hw_catalog")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681918/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-3-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The dpu_plane_virtual_assign_resources function might fail if there is
no suitable SSPP(s) for the plane. This leaves sspp field in plane
state uninitialized and later leads to NULL dereference during commit:
Call trace:
_dpu_crtc_blend_setup+0x194/0x620 [msm] (P)
dpu_crtc_atomic_begin+0xe4/0x240 [msm]
drm_atomic_helper_commit_planes+0x88/0x358
msm_atomic_commit_tail+0x1b4/0x8b8 [msm]
commit_tail+0xa8/0x1b0
drm_atomic_helper_commit+0x180/0x1a0
drm_atomic_commit+0x94/0xe0
drm_mode_atomic_ioctl+0xa88/0xd60
drm_ioctl_kernel+0xc4/0x138
drm_ioctl+0x364/0x4f0
__arm64_sys_ioctl+0xac/0x108
invoke_syscall.constprop.0+0x48/0x100
el0_svc_common.constprop.0+0x40/0xe8
do_el0_svc+0x24/0x38
el0_svc+0x30/0xe0
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x198/0x1a0
Fixes: 3ed12a3664b3 ("drm/msm/dpu: allow sharing SSPP between planes")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681916/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-2-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Due to condition in dpu_rm_reserve_sspp, RGB SSPPs are only tried when
scaling is requested, which prevents those SSPPs from being reserved if
we don't need scaling at all. Instead we should check if YUV support is
requested, since scaling on RGB SSPPs is optional and is not implemented
in driver yet.
Fixes: 774bcfb73176 ("drm/msm/dpu: add support for virtual planes")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681914/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-1-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
When in bonded DSI mode, only one PLL in one DSI PHY is used for both
DSI PHYs, meaning that parents of the secondary DSI PHY will use the
primary DSI PHY PLL as parent.
In this case the primary DSI PHY PLL will be set even if the primary
DSI PHY is not yet enabled. The DSI PHY code has support for this
particular use-case and will handle the fact the PLL was already
set when initializing the primary DSI PHY.
By introducing a protected variable pll_enable_cnt in the commit
cb55f39bf7b1 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared"),
this variable is only initially set to 1 when the DSI PHY is initialized
making it impossible to set the PLL before, breaking the bonded DSI
use case by returning 0 when setting the PLL from the secondary DSI
PHY driver and skipping the correct clocks initialization.
But since it was already possible to set the PLL without enabling
the DSI PHY, just drop the pll_enable_cnt setting from the PHY
enable/disable and simply increment/decrement the pll_enable_cnt
variable from the dsi_pll_enable/disable_pll_bias to make sure any
PLL operation is done with the PLL BIAS enabled.
Fixes: cb55f39bf7b1 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared")
Closes: https://lore.kernel.org/all/50a49d72-2b1e-471d-b0c4-d5a0b38b2a21@linaro.org/
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/683688/
Link: https://lore.kernel.org/r/20251027-topic-sm8x50-fix-dsi-bonded-v1-1-a477cd3f907d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Actually check the return value from pll_ops->init_pll()
as it can return an error.
If the card's BIOS didn't run because it's not the primary VGA card
the fact that the xclk source is unsupported is printed as shown
below but the driver continues on regardless and on my machine causes
a hard lock up.
[ 61.470088] atyfb 0000:03:05.0: enabling device (0080 -> 0083)
[ 61.476191] atyfb: using auxiliary register aperture
[ 61.481239] atyfb: 3D RAGE XL (Mach64 GR, PCI-33) [0x4752 rev 0x27]
[ 61.487569] atyfb: 512K SGRAM (1:1), 14.31818 MHz XTAL, 230 MHz PLL, 83 Mhz MCLK, 63 MHz XCLK
[ 61.496112] atyfb: Unsupported xclk source: 5.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
|
|
Recently, we discovered the following issue through syzkaller:
BUG: KASAN: slab-use-after-free in fb_mode_is_equal+0x285/0x2f0
Read of size 4 at addr ff11000001b3c69c by task syz.xxx
...
Call Trace:
<TASK>
dump_stack_lvl+0xab/0xe0
print_address_description.constprop.0+0x2c/0x390
print_report+0xb9/0x280
kasan_report+0xb8/0xf0
fb_mode_is_equal+0x285/0x2f0
fbcon_mode_deleted+0x129/0x180
fb_set_var+0xe7f/0x11d0
do_fb_ioctl+0x6a0/0x750
fb_ioctl+0xe0/0x140
__x64_sys_ioctl+0x193/0x210
do_syscall_64+0x5f/0x9c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Based on experimentation and analysis, during framebuffer unregistration,
only the memory of fb_info->modelist is freed, without setting the
corresponding fb_display[i]->mode to NULL for the freed modes. This leads
to UAF issues during subsequent accesses. Here's an example of reproduction
steps:
1. With /dev/fb0 already registered in the system, load a kernel module
to register a new device /dev/fb1;
2. Set fb1's mode to the global fb_display[] array (via FBIOPUT_CON2FBMAP);
3. Switch console from fb to VGA (to allow normal rmmod of the ko);
4. Unload the kernel module, at this point fb1's modelist is freed, leaving
a wild pointer in fb_display[];
5. Trigger the bug via system calls through fb0 attempting to delete a mode
from fb0.
Add a check in do_unregister_framebuffer(): if the mode to be freed exists
in fb_display[], set the corresponding mode pointer to NULL.
Signed-off-by: Quanmin Yan <yanquanmin1@huawei.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
|
|
bit_putcs_aligned()/unaligned() derived the glyph pointer from the
character value masked by 0xff/0x1ff, which may exceed the actual font's
glyph count and read past the end of the built-in font array.
Clamp the index to the actual glyph count before computing the address.
This fixes a global out-of-bounds read reported by syzbot.
Reported-by: syzbot+793cf822d213be1a74f2@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=793cf822d213be1a74f2
Tested-by: syzbot+793cf822d213be1a74f2@syzkaller.appspotmail.com
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
|
|
Commit e24cca19babe ("sh: Kill off MAX_DMA_ADDRESS leftovers.") removed
the define ONCHIP_NR_DMA_CHANNELS. So that the leftover reference needs
to be replaced by CONFIG_NR_ONCHIP_DMA_CHANNELS to compile successfully
with CONFIG_PVR2_DMA enabled.
Signed-off-by: Florian Fuchs <fuchsfl@gmail.com>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
|
|
The of_find_node_by_name() function returns a device tree node with its
reference count incremented. The caller is responsible for calling
of_node_put() to release this reference when done.
Found via static analysis.
Fixes: cc5d0189b9ba ("[PATCH] powerpc: Remove device_node addrs/n_addr")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Before this commit, it was possible to create end of address space
mappings, but unmapping them via VFIO_IOMMU_UNMAP_DMA, replaying them
for newly added iommu domains, and querying their dirty pages via
VFIO_DMA_UNMAP_FLAG_GET_DIRTY_BITMAP was broken due to bugs caused by
comparisons against (iova + size) expressions, which overflow to zero.
Additionally, there appears to be a page pinning leak in the
vfio_iommu_type1_release() path, since vfio_unmap_unpin()'s loop body
where unmap_unpin_*() are called will never be entered due to overflow
of (iova + size) to zero.
This commit handles DMA map/unmap operations up to the addressable
limit by comparing against inclusive end-of-range limits, and changing
iteration to perform relative traversals across range sizes, rather than
absolute traversals across addresses.
vfio_link_dma() inserts a zero-sized vfio_dma into the rb-tree, and is
only used for that purpose, so discard the size from consideration for
the insertion point.
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Fixes: 73fa0d10d077 ("vfio: Type1 IOMMU implementation")
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Alex Mastro <amastro@fb.com>
Link: https://lore.kernel.org/r/20251028-fix-unmap-v6-3-2542b96bcc8e@fb.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
Move incrementing iova to the caller of these functions as part of
preparing to handle end of address space map/unmap.
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Fixes: 73fa0d10d077 ("vfio: Type1 IOMMU implementation")
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Alex Mastro <amastro@fb.com>
Link: https://lore.kernel.org/r/20251028-fix-unmap-v6-2-2542b96bcc8e@fb.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
Adopt check_*_overflow() functions to clearly express overflow check
intent.
Tested-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Fixes: 73fa0d10d077 ("vfio: Type1 IOMMU implementation")
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Alex Mastro <amastro@fb.com>
Link: https://lore.kernel.org/r/20251028-fix-unmap-v6-1-2542b96bcc8e@fb.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
Use the similar logic in skl_plane_has_planar(),
glk_plane_has_planar() and skl_plane_has_rc_ccs() to avoid
having to think too much when comparing the three.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-9-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
Extract glk_plane_has_planar() out from skl_plane_has_planar()
to make the logic a bit less convoluted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-8-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
We don't need to check for crtc hw.enable because that would also
imply that the plane is disabled and we would have bailed out already
earlier.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-7-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
Make the skl+ plane size checks a bit more regular by
adding intel_plane_min_height() instead of using a hardcoded
1 everwhere.
v2: s/1/min_height/ one more time
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-6-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
Currently we check the plane min size only for the Y plane.
Extend the check to the CbCr plane as well.
This will also allow us to remove the planar format check from
icl_plane_min_width() since the +2 on the CbCr plane is equivalent
to +4 on the Y plane. I suspect this approach actually models the
hardware issue more accurately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-5-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
PTL+ spposedly still has the same plane min width limit
as ADL. Check for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-4-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
ADL+ no longer need the plane min width w/a (Wa_14011264657 or
Wa_14011050563). Don't apply it there. DG2 still needs it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-3-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
Replace the ginormous switch statement in icl_plane_min_width() with
simple arithmetic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251009211313.30234-2-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
|
|
On ADL-S the main DMC HRR event DMC_EVT_CTL/HTP are never
restored to their previous values during DC6 exit. This
angers assert_dmc_loaded(), and basically makes the HRR
handler unusable because we don't rewrite EVT_HTP when
enabling DMC events.
Let's just clear the HRR EVT_CTL/HTP to zero from the
beginnning so that the expected value matches the post-DC6
reality.
I suppose if we ever had actual use for HRR we'd have to both,
reject HRR+PSR, and reprogram EVT_HTP when enabling the event.
But for now we don't care about HRR so keeping both registers
zeroed is fine.
Cc: stable@vger.kernel.org
Tested-by: Petr Vorel <pvorel@suse.cz>
Fixes: 43175c92d403 ("drm/i915/dmc: Assert DMC is loaded harder")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/15153
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251022100718.24803-2-ville.syrjala@linux.intel.com
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 4df3b340ff6e9f499735d8b52b96a9257fde3918)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
When the requested PTP feature is not supported,
ixgbe_ptp_feature_enable() returns -ENOTSUPP, causing userland programs
to get "Unknown error 524".
Since EOPNOTSUPP should be used when error is propagated to userland,
return -EOPNOTSUPP instead of -ENOTSUPP.
Fixes: 3a6a4edaa592 ("ixgbe: Hardware Timestamping + PTP Hardware Clock (PHC)")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
igc_ethtool_get_sset_count() returns -ENOTSUPP when a given stringset is
not supported, causing userland programs to get "Unknown error 524".
Since EOPNOTSUPP should be used when error is propagated to userland,
return -EOPNOTSUPP instead of -ENOTSUPP.
Fixes: 36b9fea60961 ("igc: Add support for statistics")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
igb_get_sset_count() returns -ENOTSUPP when a given stringset is not
supported, causing userland programs to get "Unknown error 524".
Since EOPNOTSUPP should be used when error is propagated to userland,
return -EOPNOTSUPP instead of -ENOTSUPP.
Fixes: 9d5c824399de ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current implementation of the igc driver doesn't power up the PHY
before the link test in igc_ethtool_diag_test(), causing the link test
to always report FAIL when admin state is down and the PHY is
consequently powered down.
To test the link state regardless of admin state, power up the PHY
before the link test in the offline test path. After the link test, the
original PHY state is restored by igc_reset(), so additional code which
explicitly restores the original state is not necessary.
Note that this change is applied only for the offline test path. This is
because in the online path we shouldn't interrupt normal networking
operation and powering up the PHY and restoring the original state would
interrupt that.
This implementation also uses igc_power_up_phy_copper() without checking
the media type, since igc devices are currently only copper devices and
the function is called in other places without checking the media type.
Furthermore, the powering up is on a best-effort basis, that is, we
don't handle failures of powering up (e.g. bus error) and just let the
test report FAIL.
Tested on Intel Corporation Ethernet Controller I226-V (rev 04) with
cable connected and link available.
Set device down and do ethtool test.
# ip link set dev enp0s5 down
Without patch:
# ethtool --test enp0s5
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 1
With patch:
# ethtool --test enp0s5
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Fixes: f026d8ca2904 ("igc: add support to eeprom, registers and link self-tests")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The error path of ixgbe_recovery_probe() has two memory bugs.
For non-E610 adapters, the function jumps to clean_up_probe without
calling devlink_free(), leaking the devlink instance and its embedded
adapter structure.
For E610 adapters, devlink_free() is called at shutdown_aci, but
clean_up_probe then accesses adapter->state, sometimes triggering
use-after-free because adapter is embedded in devlink. This UAF is
similar to the one recently reported in ixgbe_remove(). (Link)
Fix both issues by moving devlink_free() after adapter->state access,
aligning with the cleanup order in ixgbe_probe().
Link: https://lore.kernel.org/intel-wired-lan/20250828020558.1450422-1-den@valinux.co.jp/
Fixes: 29cb3b8d95c7 ("ixgbe: add E610 implementation of FW recovery mode")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In some devices, the function numbers used are non-contiguous. For
example, here is such configuration for E825 device:
root@/home/root# lspci -v | grep Eth
0a:00.0 Ethernet controller: Intel Corporation Ethernet Connection
E825-C for backplane (rev 04)
0a:00.1 Ethernet controller: Intel Corporation Ethernet Connection
E825-C for backplane (rev 04)
0a:00.4 Ethernet controller: Intel Corporation Ethernet Connection
E825-C 10GbE (rev 04)
0a:00.5 Ethernet controller: Intel Corporation Ethernet Connection
E825-C 10GbE (rev 04)
When distributing RSS and FDIR masks, which are global resources across
the active devices, it is required to have a contiguous PF id, which can
be described as a logical PF id. In the case above, function 0 would
have a logical PF id of 0, function 1 would have a logical PF id
of 1, and functions 4 and 5 would have a logical PF ids 2 and 3
respectively.
Using logical PF id can properly describe which slice of resources can
be used by a particular PF.
The 'function id' to 'logical id' mapping has been introduced with the
commit 015307754a19 ("ice: Support VF queue rate limit and quanta size
configuration"). However, the usage of 'logical_pf_id' field was
unintentionally skipped for profile mask configuration.
Fix it by using 'logical_pf_id' instead of 'pf_id' value when configuring
masks.
Without that patch, wrong indexes, i.e. out of range for given PF, can
be used while configuring resources masks, which might lead to memory
corruption and undefined driver behavior.
The call trace below is one of the examples of such error:
[ +0.000008] WARNING: CPU: 39 PID: 3830 at drivers/base/devres.c:1095
devm_kfree+0x70/0xa0
[ +0.000002] RIP: 0010:devm_kfree+0x70/0xa0
[ +0.000001] Call Trace:
[ +0.000002] <TASK>
[ +0.000002] ice_free_hw_tbls+0x183/0x710 [ice]
[ +0.000106] ice_deinit_hw+0x67/0x90 [ice]
[ +0.000091] ice_deinit+0x20d/0x2f0 [ice]
[ +0.000076] ice_remove+0x1fa/0x6a0 [ice]
[ +0.000075] pci_device_remove+0xa7/0x1d0
[ +0.000010] device_release_driver_internal+0x365/0x530
[ +0.000006] driver_detach+0xbb/0x170
[ +0.000003] bus_remove_driver+0x117/0x290
[ +0.000007] pci_unregister_driver+0x26/0x250
Fixes: 015307754a19 ("ice: Support VF queue rate limit and quanta size configuration")
Suggested-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
On dual complex E825, only complex 0 has functional CGU (Clock
Generation Unit), powering all the PHYs.
SBQ (Side Band Queue) destination device 'cgu' in current implementation
points to CGU on current complex and, in order to access primary CGU
from the secondary complex, the driver should use 'cgu_peer' as
a destination device in read/write CGU registers operations.
Define new 'cgu_peer' (15) as RDA (Remote Device Access) client over
SB-IOSF interface and use it as device target when accessing CGU from
secondary complex.
This problem has been identified when working on recovery clock
enablement [1]. In existing implementation for E825 devices, only PF0,
which is clock owner, is involved in CGU configuration, thus the
problem was not exposed to the user.
[1] https://lore.kernel.org/intel-wired-lan/20250905150947.871566-1-grzegorz.nitka@intel.com/
Fixes: e2193f9f9ec9 ("ice: enable timesync operation on 2xNAC E825 devices")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Arkadiusz Kubalewski <Arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E82X adapters do not have sequential IDs, lane number is PF ID.
Add check for ICE_MAC_GENERIC and skip checking port options.
Also, adjust logical port number for specific E825 device with external
PHY support (PCI device id 0x579F). For this particular device,
with 2x25G (PHY0) and 2x10G (PHY1) port configuration, modification of
pf_id -> lane_number mapping is required. PF IDs on the 2nd PHY start
from 4 in such scenario. Otherwise, the lane number cannot be
determined correctly, leading to PTP init errors during PF initialization.
Fixes: 258f5f9058159 ("ice: Add correct PHY lane assignment")
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
drm_{crtc,plane,connector,private_obj}_get_state() must not
be called after the atomic check phase. At that point the commit
has been carved in stone and no new objects must be introduced
into it. WARN if anyone attempts to violate this rule.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251017163327.9074-2-ville.syrjala@linux.intel.com
Reviewed-by: Maxime Ripard <mripard@kernel.org>
|
|
The crtc/plane/connector counterparts of
drm_atomic_get_private_obj_state() all WARN about a missing
acquire_ctx. Do the same in drm_atomic_get_private_obj_state()
for consistency.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251017163327.9074-1-ville.syrjala@linux.intel.com
Reviewed-by: Maxime Ripard <mripard@kernel.org>
|
|
Fixed a misspelling of Xiaomi.
Signed-off-by: Lazar Aleksic <kripticni.dev@gmail.com>
Link: https://patch.msgid.link/20251028180956.10753-1-kripticni.dev@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
caab002d5069 ("PCI: brcmstb: Disable L0s component of ASPM if requested")
set PCI_EXP_LNKCAP_ASPM_L1 and (optionally) PCI_EXP_LNKCAP_ASPM_L0S in
PCI_EXP_LNKCAP (aka PCIE_RC_CFG_PRIV1_LINK_CAPABILITY in brcmstb).
But instead of using PCI_EXP_LNKCAP_ASPM_L1 and PCI_EXP_LNKCAP_ASPM_L0S
directly, it used PCIE_LINK_STATE_L1 and PCIE_LINK_STATE_L0S, which are
Linux-created values that only coincidentally matched the PCIe spec.
b478e162f227 ("PCI/ASPM: Consolidate link state defines") later changed
them so they no longer matched the PCIe spec, so the bits ended up in the
wrong place in PCI_EXP_LNKCAP.
Use PCI_EXP_LNKCAP_ASPM_L0S to clear L0s support when there's an
'aspm-no-l0s' property. Rely on brcmstb hardware to advertise L0s and/or
L1 support otherwise.
Fixes: caab002d5069 ("PCI: brcmstb: Disable L0s component of ASPM if requested")
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Closes: https://lore.kernel.org/linux-pci/20250925194424.GA2197200@bhelgaas
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[mani: reworded subject and description, added closes tag and CCed stable]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251003170436.1446030-1-james.quinlan@broadcom.com
|
|
Diamond Rapids does not support the iTCO feature.
Adding also the missing comment describing Diamond
Rapids while at it.
Fixes: 084cbc58e720 ("i2c: i801: Add support for Intel Diamond Rapids")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20251028105342.2281687-1-heikki.krogerus@linux.intel.com
|
|
The new common domain number allocator can replace the custom allocator
in VMD.
Beyond some code reuse benefits it does close a potential race whereby
vmd_find_free_domain() collides with new PCI buses coming online with a
conflicting domain number. Such a race has not been observed in practice,
hence not tagging this change as a fix.
As VMD uses pci_create_root_bus() rather than pci_alloc_host_bridge() +
pci_scan_root_bus_bridge() it has no chance to set ->domain_nr in the
bridge so needs to manage freeing the domain number on its own.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Szymon Durawa <szymon.durawa@linux.intel.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Link: https://patch.msgid.link/20251024224622.1470555-3-dan.j.williams@intel.com
|
|
The ability to emulate a host bridge is useful not only for hardware PCI
controllers like CONFIG_VMD, or virtual PCI controllers like
CONFIG_PCI_HYPERV, but also for test and development scenarios like
CONFIG_SAMPLES_DEVSEC [1].
One stumbling block for defining CONFIG_SAMPLES_DEVSEC, a sample
implementation of a platform TSM for PCI Device Security, is the need to
accommodate PCI_DOMAINS_GENERIC architectures alongside x86 [2].
In support of supplementing the existing CONFIG_PCI_BRIDGE_EMUL
infrastructure for host bridges:
* Introduce pci_bus_find_emul_domain_nr() as a common way to find a free
PCI domain number whether that is to reuse the existing dynamic
allocation code in the !ACPI case, or to assign an unused domain above
the last ACPI segment.
* Convert pci-hyperv to the new allocator so that the PCI core can
unconditionally assume that bridge->domain_nr != PCI_DOMAIN_NR_NOT_SET
is the dynamically allocated case.
A follow on patch can also convert vmd to the new scheme. Currently vmd is
limited to CONFIG_PCI_DOMAINS_GENERIC=n (x86) so, unlike pci-hyperv, it
does not immediately conflict with this new pci_bus_find_emul_domain_nr()
mechanism.
Link: http://lore.kernel.org/174107249038.1288555.12362100502109498455.stgit@dwillia2-xfh.jf.intel.com [1]
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Closes: http://lore.kernel.org/20250311144601.145736-3-suzuki.poulose@arm.com [2]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Link: https://patch.msgid.link/20251024224622.1470555-2-dan.j.williams@intel.com
|
