summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)Author
2022-04-15serial: 8250: Add UART_CAP_NOTEMT on PORT_16550A_FSL64Eric Tremblay
The Freescale variant of the 16550A doesn't have an interrupt on TEMT available when using the FIFO mode. Signed-off-by: Eric Tremblay <etremblay@distech-controls.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20220330104642.229507-3-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: 8250: Handle UART without interrupt on TEMT using em485Eric Tremblay
Introduce the UART_CAP_NOTEMT capability. The capability indicates that the UART doesn't have an interrupt available on TEMT. In the case where the device does not support it, we calculate the maximum time it could take for the transmitter to empty the shift register. When we get in the situation where we get the THRE interrupt, we check if the TEMT bit is set. If it's not, we start the a timer and recall __stop_tx() after the delay. The transmit sequence is a bit modified when the capability is set. The new timer is used between the last interrupt(THRE) and a potential stop_tx timer. Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com> [moved to use added UART_CAP_TEMT] Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> [moved to use added UART_CAP_NOTEMT, improve timeout] Signed-off-by: Eric Tremblay <etremblay@distech-controls.com> [rebased to v5.17, making use of tty_get_frame_size] Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20220330104642.229507-2-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: 8250_aspeed_vuart: Fix potential NULL dereference in aspeed_vuart_probeMiaoqian Lin
platform_get_resource() may fail and return NULL, so we should better check it's return value to avoid a NULL pointer dereference. Fixes: 54da3e381c2b ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220404143842.16960-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: atmel: remove redundant assignment in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already assigns the passed serial_rs485 struct to the uart port. So remove the assignment from the drivers rs485_config() function to avoid redundancy. Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-10-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: fsl_lpuart: remove redundant code in rs485_config functionsLino Sanfilippo
In uart_set_rs485_config() the serial core already ensures that only one of both options RTS on send or RTS after send is set. It also assigns the passed serial_rs485 struct to the uart port. So remove the check and the assignment from the drivers rs485_config() function to avoid redundancy. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-9-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: imx: remove redundant assignment in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already assigns the passed serial_rs485 struct to the uart port. So remove the assignment in the drivers rs485_config() function to avoid reduncancy. Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-8-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: max310: remove redundant memset in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already nullifies the padding field of the passed serial_rs485 struct before returning it to userspace. Doing the same in the drivers rs485_config() function is redundant, so remove the concerning memset in this function. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-7-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: omap: remove redundant code in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already clamps the RTS delays. It also assigns the passed serial_rs485 struct to the uart port. So remove these tasks from the drivers rs485_config() function to avoid redundancy. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-6-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: sc16is7xx: remove redundant check in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already ensures that only one of both options RTS on send or RTS after send is set. So remove this check from the drivers rs485_config() function to avoid redundancy. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-5-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: stm32: remove redundant code in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already ensures that only one of both options RTS on send or RTS after send is set. It also assigns the passed serial_rs485 struct to the uart port. So remove the check and the assignment from the drivers rs485_config() function to avoid redundancy. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-4-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: amba-pl011: remove redundant code in rs485_configLino Sanfilippo
In uart_set_rs485_config() the serial core already - ensures that only one of both options RTS on send or RTS after send is set - nullifies the padding field of the passed serial_rs485 struct - clamps the RTS delays - assigns the passed serial_rs485 struct to the uart port So remove these tasks from the code of the drivers rs485_config() function to avoid redundancy. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-3-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: core: move RS485 configuration tasks from drivers into coreLino Sanfilippo
Several drivers that support setting the RS485 configuration via userspace implement one or more of the following tasks: - in case of an invalid RTS configuration (both RTS after send and RTS on send set or both unset) fall back to enable RTS on send and disable RTS after send - nullify the padding field of the returned serial_rs485 struct - copy the configuration into the uart port struct - limit RTS delays to 100 ms Move these tasks into the serial core to make them generic and to provide a consistent behaviour among all drivers. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Link: https://lore.kernel.org/r/20220410104642.32195-2-LinoSanfilippo@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15tty: serial: meson: Use DIV_ROUND_CLOSEST to calculate baud ratesYu Tu
Due to chip process differences, chip designers recommend using baud rates as close to and larger as possible in order to reduce clock errors. Signed-off-by: Yu Tu <yu.tu@amlogic.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220407081355.13602-2-yu.tu@amlogic.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: 8250: Report which option to enable for blacklisted PCI devicesMaciej W. Rozycki
Provide information in the kernel log as to what configuration option to enable for PCI UART devices that have been blacklisted in the generic PCI 8250 UART driver and which have a dedicated driver available to handle that has been disabled. The rationale is there is no easy way for the user to map a specific PCI vendor:device pair to an individual dedicated driver while the generic driver has this information readily available and it will likely be confusing that the generic driver does not register such a port. This is unlike usual drivers, such as drivers/net/ethernet/3com/3c59x.c which handles all the hardware family members regardless of differences between them, and following an existing example where a serio driver provides suggestions as to the correct configuration options to use: psmouse serio1: synaptics: The touchpad can support a better bus than the too old PS/2 protocol. Make sure MOUSE_PS2_SYNAPTICS_SMBUS and RMI4_SMB are enabled to get a better touchpad experience. A message is then printed like: serial 0000:04:00.3: ignoring port, enable SERIAL_8250_PERICOM to handle when an affected device is encountered and the generic driver rejects it. Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203310054120.44113@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15serial: 8250: Make SERIAL_8250_EM available for arm64 systemsPhil Edworthy
This is needed for the Renesas RZ/V2M (r9a09g011) SoC. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20220330154024.112270-6-phil.edworthy@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15tty: serial: owl: Fix missing clk_disable_unprepare() in owl_uart_probeMiaoqian Lin
Fix the missing clk_disable_unprepare() before return from owl_uart_probe() in the error handling case. Fixes: abf42d2f333b ("tty: serial: owl: add "much needed" clk_prepare_enable()") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220307105135.11698-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15tty: serial: samsung: add spin_lock for interrupt and console_writeJaewon Kim
The console_write and IRQ handler can run concurrently. Problems may occurs console_write is continuously executed while the IRQ handler is running. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> Link: https://lore.kernel.org/r/20220407071619.102249-2-jaewon02.kim@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15tty: Fix a possible resource leak in icom_probeHuang Guobin
When pci_read_config_dword failed, call pci_release_regions() and pci_disable_device() to recycle the resource previously allocated. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Huang Guobin <huangguobin4@huawei.com> Link: https://lore.kernel.org/r/20220331091005.3290753-1-huangguobin4@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15tty: serial: Prepare cleanup of powerpc's asm/prom.hChristophe Leroy
powerpc's asm/prom.h brings some headers that it doesn't need itself. In order to clean it up, first add missing headers in users of asm/prom.h Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Link: https://lore.kernel.org/r/49fc0d4b6446da630b1e9f29c4bab38f8ed087bf.1648833419.git.christophe.leroy@csgroup.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-14tty: serial: altera: use altera_jtaguart_stop_tx()Jiri Slaby
altera_jtaguart_tx_chars() duplicates what altera_jtaguart_stop_tx() already does. So instead of the duplication, call the helper instead. Not only it makes the code cleaner, but it also says what the "if" really does. Cc: Tobias Klauser <tklauser@distanz.ch> Acked-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220411104506.8990-4-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-14tty: serial: owl-uart, send x_char even if stoppedJiri Slaby
Flow control characters should be sent even if the TX is stopped. So fix owl-uart to behave the same as other drivers. This unification also allows the use of the TX helper in the future. Cc: "Andreas Färber" <afaerber@suse.de> Cc: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220411104506.8990-3-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-14tty: serial: mpc52xx_uart: remove double ifdefferyJiri Slaby
The code now contains: #ifdef CONFIG_PPC_MPC512x ... #endif #ifdef CONFIG_PPC_MPC512x ... #endif So remove the endif+ifdef from the middle, provided it's about the same define. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220411104506.8990-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-04Merge branch 'remove-h8300' of git://git.infradead.org/users/hch/misc into ↵Arnd Bergmann
asm-generic * 'remove-h8300' of git://git.infradead.org/users/hch/misc: remove the h8300 architecture This is clearly the least actively maintained architecture we have at the moment, and probably the least useful. It is now the only one that does not support MMUs at all, and most of the boards only support 4MB of RAM, out of which the defconfig kernel needs more than half just for .text/.data. Guenter Roeck did the original patch to remove the architecture in 2013 after it had already been obsolete for a while, and Yoshinori Sato brought it back in a much more modern form in 2015. Looking at the git history since the reinstantiation, it's clear that almost all commits in the tree are build fixes or cross-architecture cleanups: $ git log --no-merges --format=%an v4.5.. arch/h8300/ | sort | uniq -c | sort -rn | head -n 12 25 Masahiro Yamada 18 Christoph Hellwig 14 Mike Rapoport 9 Arnd Bergmann 8 Mark Rutland 7 Peter Zijlstra 6 Kees Cook 6 Ingo Molnar 6 Al Viro 5 Randy Dunlap 4 Yury Norov Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-04tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned, part II.Jiri Slaby
The below commit changed types of some hooks in struct psc_ops. It also changed the types of the functions which are referenced in the instances of the above struct. However the commit did so only for CONFIG_PPC_MPC52xx, but not for CONFIG_PPC_MPC512x. This results in build errors like: mpc52xx_uart.c:static unsigned int mpc52xx_psc_raw_tx_rdy(struct uart_port *port) mpc52xx_uart.c:static int mpc512x_psc_raw_tx_rdy(struct uart_port *port) ^^^ mpc52xx_uart.c:static int mpc5125_psc_raw_tx_rdy(struct uart_port *port) ^^^ Therefore, fix the latter case now too. Fixes: 18662a1d8f35 (tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned) Cc: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220404055122.31194-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-28Merge tag 'tty-5.18-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here are the big set of tty and serial driver changes for 5.18-rc1. Nothing major, some more good cleanups from Jiri and 2 new serial drivers. Highlights include: - termbits cleanups - export symbol cleanups and other core cleanups from Jiri Slaby - new sunplus and mvebu uart drivers (amazing that people are still creating new uarts...) - samsung serial driver cleanups - ldisc 29 is now "reserved" for experimental/development line disciplines - lots of other tiny fixes and cleanups to serial drivers and bindings All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (104 commits) vt_ioctl: fix potential spectre v1 in VT_DISALLOCATE serial: 8250: fix XOFF/XON sending when DMA is used tty: serial: samsung: Add ARTPEC-8 support dt-bindings: serial: samsung: Add ARTPEC-8 UART serial: sc16is7xx: Clear RS485 bits in the shutdown tty: serial: samsung: simplify getting OF match data tty: serial: samsung: constify variables and pointers tty: serial: samsung: constify s3c24xx_serial_drv_data members tty: serial: samsung: constify UART name tty: serial: samsung: constify s3c24xx_serial_drv_data tty: serial: samsung: reduce number of casts tty: serial: samsung: embed s3c2410_uartcfg in parent structure tty: serial: samsung: embed s3c24xx_uart_info in parent structure serial: 8250_tegra: mark acpi_device_id as unused with !ACPI tty: serial: bcm63xx: use more precise Kconfig symbol serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUS tty: serial: jsm: fix two assignments in if conditions tty: serial: jsm: remove redundant assignments to variable linestatus serial: 8250_mtk: make two read-only arrays static const serial: samsung_tty: do not unlock port->lock for uart_write_wakeup() ...
2022-03-21Merge tag 'spi-v5.18' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi updates from Mark Brown: "The overwhelming bulk of this pull request is a change from Uwe Kleine-König which changes the return type of the remove() function to void as part of some wider work he's doing to do this for all bus types, causing updates to most SPI device drivers. The branch with that on has been cross merged with a couple of other trees which added new SPI drivers this cycle, I'm not expecting any build issues resulting from the change. Otherwise it's been a relatively quiet release with some new device support, a few minor features and the welcome completion of the conversion of the subsystem to use GPIO descriptors rather than numbers: - Change return type of remove() to void. - Completion of the conversion of SPI controller drivers to use GPIO descriptors rather than numbers. - Quite a few DT schema conversions. - Support for multiple SPI devices on a bus in ACPI systems. - Big overhaul of the PXA2xx SPI driver. - Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and Sunplus SP7021" [ And this is obviously where that spi change that snuck into the regulator tree _should_ have been :^] * tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits) spi: fsi: Implement a timeout for polling status spi: Fix erroneous sgs value with min_t() spi: tegra20: Use of_device_get_match_data() spi: mediatek: add ipm design support for MT7986 spi: Add compatible for MT7986 spi: sun4i: fix typos in comments spi: mediatek: support tick_delay without enhance_timing spi: Update clock-names property for arm pl022 spi: rockchip-sfc: fix platform_get_irq.cocci warning spi: s3c64xx: Add spi port configuration for Tesla FSD SoC spi: dt-bindings: samsung: Add fsd spi compatible spi: topcliff-pch: Prevent usage of potentially stale DMA device spi: tegra210-quad: combined sequence mode spi: tegra210-quad: add acpi support spi: npcm-fiu: Fix typo ("npxm") spi: Fix Tegra QSPI example spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ spi: cadence: fix platform_get_irq.cocci warning spi: Update NXP Flexspi maintainer details dt-bindings: mfd: maxim,max77802: Convert to dtschema ...
2022-03-18serial: 8250: fix XOFF/XON sending when DMA is usedIlpo Järvinen
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent to the wire. After this change, x_char is injected correctly. Create uart_xchar_out() helper for sending the x_char out and accounting related to it. It seems that almost every driver does these same steps with x_char. Except for 8250, however, almost all currently lack .serial_out so they cannot immediately take advantage of this new helper. The downside of this patch is that it might reintroduce the problems some devices faced with mixed DMA/non-DMA transfer which caused revert f967fc8f165f (Revert "serial: 8250_dma: don't bother DMA with small transfers"). However, the impact should be limited to cases with XON/XOFF (that didn't work with DMA capable devices to begin with so this problem is not very likely to cause a major issue, if any at all). Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine") Reported-by: Gilles Buloz <gilles.buloz@kontron.com> Tested-by: Gilles Buloz <gilles.buloz@kontron.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: Add ARTPEC-8 supportVincent Whitchurch
Add support for the UART block on the ARTPEC-8 SoC. This is closely related to the variants used on the Exynos chips. The register layout is identical to Exynos850 et al but the fifo size is different (64 bytes in each direction for all instances). Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20220311094515.3223023-3-vincent.whitchurch@axis.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18serial: sc16is7xx: Clear RS485 bits in the shutdownHui Wang
We tested RS485 function on an EVB which has SC16IS752, after finishing the test, we started the RS232 function test, but found the RTS is still working in the RS485 mode. That is because both startup and shutdown call port_update() to set the EFCR_REG, this will not clear the RS485 bits once the bits are set in the reconf_rs485(). To fix it, clear the RS485 bits in shutdown. Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20220308110042.108451-1-hui.wang@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: simplify getting OF match dataKrzysztof Kozlowski
Simplify the code with of_device_get_match_data() and use dev_of_node() to remove ifdef-erry. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-9-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: constify variables and pointersKrzysztof Kozlowski
Constify variables, data pointed by several pointers and "udivslot_table" static array. This makes code a bit safer. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-8-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: constify s3c24xx_serial_drv_data membersKrzysztof Kozlowski
The driver data (struct s3c24xx_serial_drv_data) is never modified, so also its members can be made const. Except code style this has no impact because the structure itself is always a const. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-7-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: constify UART nameKrzysztof Kozlowski
The UART name from driver data holds only string literals. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-6-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: constify s3c24xx_serial_drv_dataKrzysztof Kozlowski
The driver data (struct s3c24xx_serial_drv_data) is only used to initialize the driver properly and is not modified. Make it const. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-5-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: reduce number of castsKrzysztof Kozlowski
The pointers to instances of "struct s3c24xx_serial_drv_data" are first cast to kernel_ulong_t and then either used directly (in "platform_device_id.driver_data") or cast again to void * (in "of_device_id.data"). One cast can be dropped, so at least for "of_device_id.data" case there will be no casts at all. This makes the code a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-4-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: embed s3c2410_uartcfg in parent structureKrzysztof Kozlowski
Embed "struct s3c2410_uartcfg" directly as a member of "struct s3c24xx_serial_drv_data" instead of keeping it as a pointer. This makes the code clearer (obvious ownership of "s3c2410_uartcfg s3c24xx_serial_drv_data") and saves one pointer. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-3-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: samsung: embed s3c24xx_uart_info in parent structureKrzysztof Kozlowski
Embed "struct s3c24xx_uart_info" directly as a member of "struct s3c24xx_serial_drv_data" instead of keeping it as a pointer. This makes the code clearer (obvious ownership of "struct s3c24xx_serial_drv_data") and saves one pointer. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308080919.152715-2-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18serial: 8250_tegra: mark acpi_device_id as unused with !ACPIKrzysztof Kozlowski
The driver's acpi_device_id table is referenced via ACPI_PTR() so it will be unused for !CONFIG_ACPI builds: drivers/tty/serial/8250/8250_tegra.c:178:36: warning: ‘tegra_uart_acpi_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20220308074157.113568-1-krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: bcm63xx: use more precise Kconfig symbolRafał Miłecki
Patches lowering SERIAL_BCM63XX dependencies led to a discussion and documentation change regarding "depends" usage. Adjust Kconfig entry to match current guidelines. Make this symbol available for relevant architectures only. Cc: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Ref: f35a07f92616 ("tty: serial: bcm63xx: lower driver dependencies") Ref: 18084e435ff6 ("Documentation/kbuild: Document platform dependency practises") Link: https://lore.kernel.org/r/20220311093233.10012-1-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUSGeert Uytterhoeven
Sunplus serial ports are only present on Sunplus SoCs. Hence add a dependency on ARCH_SUNPLUS, to prevent asking the user about this driver when configuring a kernel without Sunplus SoC support. Fixes: 9e8d5470325f25be ("serial: sunplus-uart: Add Sunplus SoC UART Driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/59f46272ab5b16853acac4d585c3333cfd394223.1647352195.git.geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: jsm: fix two assignments in if conditionsAlexander Vorwerk
Fixes two warnings reported of the form "ERROR: do not use assignment in if condition" reported by checkpatch.pl. Signed-off-by: Alexander Vorwerk <alexander.vorwerk@stud.uni-goettingen.de> Link: https://lore.kernel.org/r/20220315020745.15752-1-alexander.vorwerk@stud.uni-goettingen.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: jsm: remove redundant assignments to variable linestatusColin Ian King
Variable linestatus is being assigned values that are never read, the assignments are redundant and can be removed. Cleans up clang scan warnings: drivers/tty/serial/jsm/jsm_cls.c:369:2: warning: Value stored to 'linestatus' is never read [deadcode.DeadStores] drivers/tty/serial/jsm/jsm_cls.c:400:4: warning: Value stored to 'linestatus' is never read [deadcode.DeadStores] Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20220307153047.139639-1-colin.i.king@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18serial: 8250_mtk: make two read-only arrays static constColin Ian King
Don't populate the read-only arrays fraction_L_mapping and fraction_M_mapping on the stack but instead make them static const. Also makes the object code a little smaller. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20220307230055.168241-1-colin.i.king@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()Jiri Slaby
The commit c15c3747ee32 (serial: samsung: fix potential soft lockup during uart write) added an unlock of port->lock before uart_write_wakeup() and a lock after it. It was always problematic to write data from tty_ldisc_ops::write_wakeup and it was even documented that way. We fixed the line disciplines to conform to this recently. So if there is still a missed one, we should fix them instead of this workaround. On the top of that, s3c24xx_serial_tx_dma_complete() in this driver still holds the port->lock while calling uart_write_wakeup(). So revert the wrap added by the commit above. Cc: Thomas Abraham <thomas.abraham@linaro.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Hyeonkook Kim <hk619.kim@samsung.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220308115153.4225-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18tty: serial: serial_txx9: remove struct uart_txx9_portJiri Slaby
It's only a wrapper to struct uart_port, so unwrap the whole code. No change in functionality is intended. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220307054348.31748-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18kgdboc: fix return value of __setup handlerRandy Dunlap
__setup() handlers should return 1 to obsolete_checksetup() in init/main.c to indicate that the boot option has been handled. A return of 0 causes the boot option/value to be listed as an Unknown kernel parameter and added to init's (limited) environment strings. So return 1 from kgdboc_option_setup(). Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7 kgdboc=kbd kgdbts=", will be passed to user space. Run /sbin/init as init process with arguments: /sbin/init with environment: HOME=/ TERM=linux BOOT_IMAGE=/boot/bzImage-517rc7 kgdboc=kbd kgdbts= Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: 1bd54d851f50 ("kgdboc: Passing ekgdboc to command line causes panic") Fixes: f2d937f3bf00 ("consoles: polling support, kgdboc") Cc: He Zhe <zhe.he@windriver.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: kgdb-bugreport@lists.sourceforge.net Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Douglas Anderson <dianders@chromium.org> Cc: linux-serial@vger.kernel.org Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220309033018.17936-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03serial: samsung: Add samsung_early_read to support early kgdbocWoody Lin
The 'kgdboc_earlycon_init' looks for boot console that has both .read and .write callbacks. Adds 'samsung_early_read' to samsung_tty.c's early console to support kgdboc. Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Woody Lin <woodylin@google.com> Link: https://lore.kernel.org/r/20220302114923.144523-1-woodylin@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03serial: make uart_console_write->putchar()'s character an unsigned charJiri Slaby
Currently, uart_console_write->putchar's second parameter (the character) is of type int. It makes little sense, provided uart_console_write() accepts the input string as "const char *s" and passes its content -- the characters -- to putchar(). So switch the character's type to unsigned char. We don't use char as that is signed on some platforms. That would cause troubles for drivers which (implicitly) cast the char to u16 when writing to the device. Sign extension would happen in that case and the value written would be completely different to the provided char. DZ is an example of such a driver -- on MIPS, it uses u16 for dz_out in dz_console_putchar(). Note we do the char -> uchar conversion implicitly in uart_console_write(). Provided we do not change size of the data type, sign extension does not happen there, so the problem is void. This makes the types consistent and unified with the rest of the uart layer, which uses unsigned char in most places already. One exception is xmit_buf, but that is going to be converted later. Cc: Paul Cercueil <paul@crapouillou.net> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@orcam.me.uk> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Karol Gugala <kgugala@antmicro.com> Cc: Mateusz Holenko <mholenko@antmicro.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang7@gmail.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <peter@korsgaard.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial] Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-01serial: mvebu-uart: fix return value check in mvebu_uart_clock_probe()Wei Yongjun
In case of error, the function devm_ioremap() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Fixes: b7e2b5360f9b ("serial: mvebu-uart: implement UART clock driver for configuring UART base clock") Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Pali Rohár <pali@kernel.org> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20220301075806.3950108-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-01sc16is7xx: Set AUTOCTS and AUTORTS bitsTomasz Moń
Let serial core know that the chip automatically handles RTS/CTS signal. This elimines completely unnecessary I2C/SPI bus traffic. Cease reading from RX FIFO (by disabling RDI interrupt) when throttled. Eventually the FIFO will fill up and the device will drive RTS output inactive. Unthrottle by enabling back RDI interrupt. Indirectly controlling RTS via RX FIFO state seems to be the only option because RTS bit is ignored when hardware flow control is enabled. Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com> Link: https://lore.kernel.org/r/20220301060332.2561851-4-tomasz.mon@camlingroup.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2026-07-12 13:24:14 +0000