summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2021-11-29net: hns3: refactor two hns3 debugfs functionsJie Wang
Use for statement to optimize some print work of function hclge_dbg_dump_rst_info() and hclge_dbg_dump_mac_enable_status() to improve code simplicity. Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: hns3: refactor hns3_nic_reuse_page()Hao Chen
Split rx copybreak handle into a separate function from function hns3_nic_reuse_page() to improve code simplicity. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: hns3: refactor reset_prepare_general retry statementJiaran Zhang
Currently, the hclge_reset_prepare_general function uses the goto statement to jump upwards, which increases code complexity and makes the program structure difficult to understand. In addition, if reset_pending is set, retry_cnt cannot be increased. This may result in a failure to exit the retry or increase the number of retries. Use the while statement instead to make the program easier to understand and solve the problem that the goto statement cannot be exited. Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29atlantic: Remove warn trace message.Sameer Saurabh
Remove the warn trace message - it's not a correct check here, because the function can still be called on the device in DOWN state Fixes: 508f2e3dce454 ("net: atlantic: split rx and tx per-queue stats") Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29atlantic: Fix statistics logic for production hardwareDmitry Bogdanov
B0 is the main and widespread device revision of atlantic2 HW. In the current state, driver will incorrectly fetch the statistics for this revision. Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops") Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29Remove Half duplex mode speed capabilities.Sameer Saurabh
Since Half Duplex mode has been deprecated by the firmware, driver should not advertise Half Duplex speed in ethtool support link speed values. Fixes: 071a02046c262 ("net: atlantic: A2: half duplex support") Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29atlantic: Add missing DIDs and fix 115c.Nikita Danilov
At the late production stages new dev ids were introduced. These are now in production, so its important for the driver to recognize these. And also fix the board caps for AQC115C adapter. Fixes: b3f0c79cba206 ("net: atlantic: A2 hw_ops skeleton") Signed-off-by: Nikita Danilov <ndanilov@aquantia.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29atlantic: Fix to display FW bundle version instead of FW mac version.Sameer Saurabh
The correct way to reflect firmware version is to use bundle version. Hence populating the same instead of MAC fw version. Fixes: c1be0bf092bd2 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops") Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29atlatnic: enable Nbase-t speeds with base-tNikita Danilov
When 2.5G is advertised, N-Base should be advertised against the T-base caps. N5G is out of use in baseline code and driver should treat both 5G and N5G (and also 2.5G and N2.5G) equally from user perspective. Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops") Signed-off-by: Nikita Danilov <ndanilov@aquantia.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29atlantic: Increase delay for fw transactionsDmitry Bogdanov
The max waiting period (of 1 ms) while reading the data from FW shared buffer is too small for certain types of data (e.g., stats). There's a chance that FW could be updating buffer at the same time and driver would be unsuccessful in reading data. Firmware manual recommends to have 1 sec timeout to fix this issue. Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops") Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net/mlx4_en: Update reported link modes for 1/10GErik Ekman
When link modes were initially added in commit 2c762679435dc ("net/mlx4_en: Use PTYS register to query ethtool settings") and later updated for the new ethtool API in commit 3d8f7cc78d0eb ("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR. It looks like these got picked to represent other modes since nothing better was available. Switch to using more specific link modes added in commit 5711a98221443 ("net: ethtool: add support for 1000BaseX and missing 10G link modes"). Tested with MCX311A-XCAT connected via DAC. Before: % sudo ethtool enp3s0 Settings for enp3s0: Supported ports: [ FIBRE ] Supported link modes: 1000baseKX/Full 10000baseKR/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: 1000baseKX/Full 10000baseKR/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 10000Mb/s Duplex: Full Auto-negotiation: off Port: Direct Attach Copper PHYAD: 0 Transceiver: internal Supports Wake-on: d Wake-on: d Current message level: 0x00000014 (20) link ifdown Link detected: yes With this change: % sudo ethtool enp3s0 Settings for enp3s0: Supported ports: [ FIBRE ] Supported link modes: 1000baseX/Full 10000baseCR/Full 10000baseSR/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: 1000baseX/Full 10000baseCR/Full 10000baseSR/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 10000Mb/s Duplex: Full Auto-negotiation: off Port: Direct Attach Copper PHYAD: 0 Transceiver: internal Supports Wake-on: d Wake-on: d Current message level: 0x00000014 (20) link ifdown Link detected: yes Tested-by: Michael Stapelberg <michael@stapelberg.ch> Signed-off-by: Erik Ekman <erik@kryo.se> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO ↵Colin Foster
access Switch to a shared MDIO access implementation by way of the mdio-mscc-miim driver. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: dsa: ocelot: seville: utilize of_mdiobus_registerColin Foster
Switch seville to use of_mdiobus_register(bus, NULL) instead of just mdiobus_register. This code is about to be pulled into a separate module that can optionally define ports by the device_node. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: mdio: mscc-miim: convert to a regmap implementationColin Foster
Utilize regmap instead of __iomem to perform indirect mdio access. This will allow for custom regmaps to be used by way of the mscc_miim_setup function. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: lan966x: add ethtool configuration and statisticsHoratiu Vultur
This patch adds support for statistics counters for the network interfaces. Also adds support for configuring the network interface via ethtool like: speed, duplex etc. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: lan966x: add mactable supportHoratiu Vultur
This patch adds support for MAC table operations like add and forget. Also add the functionality to read the MAC address from DT, if there is no MAC set in DT it would use a random one. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: lan966x: add port module supportHoratiu Vultur
This patch adds support for netdev and phylink in the switch. The injection + extraction is register based. This will be replaced with DMA accees. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: lan966x: add the basic lan966x driverHoratiu Vultur
This patch adds basic SwitchDev driver framework for lan966x. It includes only the IO range mapping and probing of the switch. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: ixp4xx_hss: Convert to use DT probingLinus Walleij
IXP4xx is being migrated to device tree only. Convert this driver to use device tree probing. Pull in all the boardfile code from the one boardfile and make it local, pull all the boardfile parameters from the device tree instead of the board file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: dsa: rtl8365mb: set RGMII RX delay in steps of 0.3 nsAlvin Šipraga
A contact at Realtek has clarified what exactly the units of RGMII RX delay are. The answer is that the unit of RX delay is "about 0.3 ns". Take this into account when parsing rx-internal-delay-ps by approximating the closest step value. Delays of more than 2.1 ns are rejected. This obviously contradicts the previous assumption in the driver that a step value of 4 was "about 2 ns", but Realtek also points out that it is easy to find more than one RX delay step value which makes RGMII work. Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC") Cc: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: dsa: rtl8365mb: fix garbled commentAlvin Šipraga
Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC") Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: dsa: realtek-smi: don't log an error on EPROBE_DEFERAlvin Šipraga
Probe deferral is not an error, so don't log this as an error: [0.590156] realtek-smi ethernet-switch: unable to register switch ret = -517 Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: wwan: Add Qualcomm BAM-DMUX WWAN network driverStephan Gerhold
The BAM Data Multiplexer provides access to the network data channels of modems integrated into many older Qualcomm SoCs, e.g. Qualcomm MSM8916 or MSM8974. It is built using a simple protocol layer on top of a DMA engine (Qualcomm BAM) and bidirectional interrupts to coordinate power control. The modem announces a fixed set of channels by sending an OPEN command. The driver exports each channel as separate network interface so that a connection can be established via QMI from userspace. The network interface can work either in Ethernet or Raw-IP mode (configurable via QMI). However, Ethernet mode seems to be broken with most firmwares (network packets are actually received as Raw-IP), therefore the driver only supports Raw-IP mode. Note that the control channel (QMI/AT) is entirely separate from BAM-DMUX and is already supported by the RPMSG_WWAN_CTRL driver. The driver uses runtime PM to coordinate power control with the modem. TX/RX buffers are put in a kind of "ring queue" and submitted via the bam_dma driver of the DMAEngine subsystem. The basic architecture looks roughly like this: +------------+ +-------+ [IPv4/6] | BAM-DMUX | | | [Data...] | | | | ---------->|wwan0 | [DMUX chan: x] | | [IPv4/6] | (chan: 0) | [IPv4/6] | | [Data...] | | [Data...] | | ---------->|wwan1 |--------------->| Modem | | (chan: 1) | BAM | | [IPv4/6] | ... | (DMA Engine) | | [Data...] | | | | ---------->|wwan7 | | | | (chan: 7) | | | +------------+ +-------+ Note that some newer firmware versions support QMAP ("rmnet" driver) as additional multiplexing layer on top of BAM-DMUX, but this is not currently supported by this driver. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: usb: lan78xx: lan78xx_phy_init(): use PHY_POLL instead of "0" if no IRQ ↵Sven Schuchmann
is available On most systems request for IRQ 0 will fail, phylib will print an error message and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ is available. Fixes: cc89c323a30e ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: hns3: use macro IANA_VXLAN_GPE_UDP_PORT to replace number 4790Hao Chen
This patch uses macro IANA_VXLAN_GPE_UDP_PORT to replace number 4790 for cleanup. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: vxlan: add macro definition for number of IANA VXLAN-GPE portHao Chen
Add macro definition for number of IANA VXLAN-GPE port for generic use. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: dsa: realtek-smi: fix indirect reg access for ports>3Luiz Angelo Daros de Luca
This switch family can have up to 8 UTP ports {0..7}. However, INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3, dropping the most significant bit during indirect register reads and writes. Reading or writing ports 4, 5, 6, and 7 registers was actually manipulating, respectively, ports 0, 1, 2, and 3 registers. This is not sufficient but necessary to support any variant with more than 4 UTP ports, like RTL8367S. rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater than 7. Fixes: 4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC") Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: stmmac: Avoid DMA_CHAN_CONTROL write if no Split Header supportVincent Whitchurch
The driver assumes that split headers can be enabled/disabled without stopping/starting the device, so it writes DMA_CHAN_CONTROL from stmmac_set_features(). However, on my system (IP v5.10a without Split Header support), simply writing DMA_CHAN_CONTROL when DMA is running (for example, with the commands below) leads to a TX watchdog timeout. host$ socat TCP-LISTEN:1024,fork,reuseaddr - & device$ ethtool -K eth0 tso off device$ ethtool -K eth0 tso on device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024 <tx watchdog timeout> Note that since my IP is configured without Split Header support, the driver always just reads and writes the same value to the DMA_CHAN_CONTROL register. I don't have access to any platforms with Split Header support so I don't know if these writes to the DMA_CHAN_CONTROL while DMA is running actually work properly on such systems. I could not find anything in the databook that says that DMA_CHAN_CONTROL should not be written when the DMA is running. But on systems without Split Header support, there is in any case no need to call enable_sph() in stmmac_set_features() at all since SPH can never be toggled, so we can avoid the watchdog timeout there by skipping this call. Fixes: 8c6fc097a2f4acf ("net: stmmac: gmac4+: Add Split Header support") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: mvneta: Add TC traffic shaping offloadMaxime Chevallier
The mvneta controller is able to do some tocken-bucket per-queue traffic shaping. This commit adds support for setting these using the TC mqprio interface. The token-bucket parameters are customisable, but the current implementation configures them to have a 10kbps resolution for the rate limitation, since it allows to cover the whole range of max_rate values from 10kbps to 5Gbps with 10kbps increments. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: mvneta: Allow having more than one queue per TCMaxime Chevallier
The current mqprio implementation assumed that we are only using one queue per TC. Use the offset and count parameters to allow using multiple queues per TC. In that case, the controller will use a standard round-robin algorithm to pick queues assigned to the same TC, with the same priority. This only applies to VLAN priorities in ingress traffic, each TC corresponding to a vlan priority. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: mvneta: Don't force-set the offloading flagMaxime Chevallier
The qopt->hw flag is set by the TC code according to the offloading mode asked by user. Don't force-set it in the driver, but instead read it to make sure we do what's asked. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: mvneta: Use struct tc_mqprio_qopt_offload for MQPrio configurationMaxime Chevallier
The struct tc_mqprio_qopt_offload is a container for struct tc_mqprio_qopt, that allows passing extra parameters, such as traffic shaping. This commit converts the current mqprio code to that new struct. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29net: mdio: ipq8064: replace ioremap() with devm_ioremap()Yang Yingliang
Use devm_ioremap() instead of ioremap() to avoid iounmap() missing. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29rt2x00: do not mark device gone on EPROTO errors during startStanislaw Gruszka
As reported by Exuvo is possible that we have lot's of EPROTO errors during device start i.e. firmware load. But after that device works correctly. Hence marking device gone by few EPROTO errors done by commit e383c70474db ("rt2x00: check number of EPROTO errors") caused regression - Exuvo device stop working after kernel update. To fix disable the check during device start. Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/ Reported-and-tested-by: Exuvo <exuvo@exuvo.se> Fixes: e383c70474db ("rt2x00: check number of EPROTO errors") Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl
2021-11-29rtlwifi: rtl8192de: Style clean-upsKees Cook
Clean up some style issues: - Use ARRAY_SIZE() even though it's a u8 array. - Remove redundant CHANNEL_MAX_NUMBER_2G define. Additionally fix some dead code WARNs. Acked-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://lore.kernel.org/lkml/57d0d1b6064342309f680f692192556c@realtek.com/ Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211119192233.1021063-1-keescook@chromium.org
2021-11-29mwl8k: Use named struct for memcpy() regionKees Cook
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Use named struct in struct mwl8k_cmd_set_key around members key_material, tkip_tx_mic_key, and tkip_rx_mic_key so they can be referenced together. This will allow memcpy() and sizeof() to more easily reason about sizes, improve readability, and avoid future warnings about writing beyond the end of key_material. "pahole" shows no size nor member offset changes to struct mwl8k_cmd_set_key. "objdump -d" shows no object code changes. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211119004905.2348143-1-keescook@chromium.org
2021-11-29intersil: Use struct_group() for memcpy() regionKees Cook
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Use struct_group() in struct hfa384x_tx_frame around members frame_control, duration_id, addr1, addr2, addr3, and seq_ctrl, so they can be referenced together. This will allow memcpy() and sizeof() to more easily reason about sizes, improve readability, and avoid future warnings about writing beyond the end of frame_control. "pahole" shows no size nor member offset changes to struct hfa384x_tx_frame. "objdump -d" shows no object code changes. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211119004646.2347920-1-keescook@chromium.org
2021-11-29libertas_tf: Use struct_group() for memcpy() regionKees Cook
In preparation for FORTIFY_SOURCE performing compile-time and run-time field array bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Use struct_group() in struct txpd around members tx_dest_addr_high and tx_dest_addr_low so they can be referenced together. This will allow memcpy() and sizeof() to more easily reason about sizes, improve readability, and avoid future warnings about writing beyond the end of tx_dest_addr_high. "pahole" shows no size nor member offset changes to struct txpd. "objdump -d" shows no object code changes. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211118184121.1283821-1-keescook@chromium.org
2021-11-29libertas: Use struct_group() for memcpy() regionKees Cook
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Use struct_group() in struct txpd around members tx_dest_addr_high and tx_dest_addr_low so they can be referenced together. This will allow memcpy() and sizeof() to more easily reason about sizes, improve readability, and avoid future warnings about writing beyond the end of queue_id. "pahole" shows no size nor member offset changes to struct txpd. "objdump -d" shows no object code changes. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211118184104.1283637-1-keescook@chromium.org
2021-11-29wlcore: no need to initialise statics to falseJason Wang
Static variables do not need to be initialized to false. The compiler will do that. Signed-off-by: Jason Wang <wangborong@cdjrlc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211113063551.257804-1-wangborong@cdjrlc.com
2021-11-29rsi: Fix out-of-bounds read in rsi_read_pkt()Zekun Shen
rsi_get_* functions rely on an offset variable from usb input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000), while 2-byte offset can be up to 0xFFFF. Thus a large offset can cause out-of-bounds read. The patch adds a bound checking condition when rcv_pkt_len is 0, indicating it's USB. It's unclear whether this is triggerable from other type of bus. The following check might help in that case. offset > rcv_pkt_len - FRAME_DESC_SZ The bug is trigerrable with conpromised/malfunctioning USB devices. I tested the patch with the crashing input and got no more bug report. Attached is the KASAN report from fuzzing. BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x] Read of size 2 at addr ffff888019439fdb by task RX-Thread/227 CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66 Call Trace: dump_stack+0x76/0xa0 print_address_description.constprop.0+0x16/0x200 ? rsi_read_pkt+0x42e/0x500 [rsi_91x] ? rsi_read_pkt+0x42e/0x500 [rsi_91x] __kasan_report.cold+0x37/0x7c ? rsi_read_pkt+0x42e/0x500 [rsi_91x] kasan_report+0xe/0x20 rsi_read_pkt+0x42e/0x500 [rsi_91x] rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb] ? rsi_probe+0x16a0/0x16a0 [rsi_usb] ? _raw_spin_lock_irqsave+0x7b/0xd0 ? _raw_spin_trylock_bh+0x120/0x120 ? __wake_up_common+0x10b/0x520 ? rsi_probe+0x16a0/0x16a0 [rsi_usb] kthread+0x2b5/0x3b0 ? kthread_create_on_node+0xd0/0xd0 ret_from_fork+0x22/0x40 Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu> Signed-off-by: Zekun Shen <bruceshenzk@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
2021-11-29rsi: Fix use-after-free in rsi_rx_done_handler()Zekun Shen
When freeing rx_cb->rx_skb, the pointer is not set to NULL, a later rsi_rx_done_handler call will try to read the freed address. This bug will very likley lead to double free, although detected early as use-after-free bug. The bug is triggerable with a compromised/malfunctional usb device. After applying the patch, the same input no longer triggers the use-after-free. Attached is the kasan report from fuzzing. BUG: KASAN: use-after-free in rsi_rx_done_handler+0x354/0x430 [rsi_usb] Read of size 4 at addr ffff8880188e5930 by task modprobe/231 Call Trace: <IRQ> dump_stack+0x76/0xa0 print_address_description.constprop.0+0x16/0x200 ? rsi_rx_done_handler+0x354/0x430 [rsi_usb] ? rsi_rx_done_handler+0x354/0x430 [rsi_usb] __kasan_report.cold+0x37/0x7c ? dma_direct_unmap_page+0x90/0x110 ? rsi_rx_done_handler+0x354/0x430 [rsi_usb] kasan_report+0xe/0x20 rsi_rx_done_handler+0x354/0x430 [rsi_usb] __usb_hcd_giveback_urb+0x1e4/0x380 usb_giveback_urb_bh+0x241/0x4f0 ? __usb_hcd_giveback_urb+0x380/0x380 ? apic_timer_interrupt+0xa/0x20 tasklet_action_common.isra.0+0x135/0x330 __do_softirq+0x18c/0x634 ? handle_irq_event+0xcd/0x157 ? handle_edge_irq+0x1eb/0x7b0 irq_exit+0x114/0x140 do_IRQ+0x91/0x1e0 common_interrupt+0xf/0xf </IRQ> Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu> Signed-off-by: Zekun Shen <bruceshenzk@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/YXxQL/vIiYcZUu/j@10-18-43-117.dynapool.wireless.nyu.edu
2021-11-29brcmfmac: Configure keep-alive packet on suspendLoic Poulain
When entering suspend as a client station with wowlan enabled, the Wi-Fi link is supposed to be maintained. In that state, no more data is generated from client side, and the link stays idle as long the station is suspended and as long the AP as no data to transmit. However, most of the APs kick-off such 'inactive' stations after few minutes, causing unexpected disconnect (reconnect, etc...). The usual way to prevent this is to submit a Null function frame periodically as a keep-alive. This is something that can be host /software generated (e.g. wpa_supplicant), but that needs to be offloaded to the Wi-Fi controller in case of suspended host. This change enables firmware generated keep-alive frames when entering wowlan suspend, using the 'mkeep_alive' IOVAR. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1637596046-21651-1-git-send-email-loic.poulain@linaro.org
2021-11-28ieee80211: change HE nominal packet padding value definesMiri Korenblit
It's easier to use and understand, and to extend for EHT later, if we use the values here instead of the shifted values. Unfortunately, we need to add _POS so that we can use it in places like iwlwifi/mvm where constants are needed. While at it, fix the typo ("NOMIMAL") which also helps catch any conflicts. Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://lore.kernel.org/r/20211126104817.7c29a05b8eb5.I2ca9faf06e177e3035bec91e2ae53c2f91d41774@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-11-28Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds
Pull vhost,virtio,vdpa bugfixes from Michael Tsirkin: "Misc fixes all over the place. Revert of virtio used length validation series: the approach taken does not seem to work, breaking too many guests in the process. We'll need to do length validation using some other approach" [ This merge also ends up reverting commit f7a36b03a732 ("vsock/virtio: suppress used length validation"), which came in through the networking tree in the meantime, and was part of that whole used length validation series - Linus ] * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: vdpa_sim: avoid putting an uninitialized iova_domain vhost-vdpa: clean irqs before reseting vdpa device virtio-blk: modify the value type of num in virtio_queue_rq() vhost/vsock: cleanup removing `len` variable vhost/vsock: fix incorrect used length reported to the guest Revert "virtio_ring: validate used buffer length" Revert "virtio-net: don't let virtio core to validate used length" Revert "virtio-blk: don't let virtio core to validate used length" Revert "virtio-scsi: don't let virtio core to validate used buffer length"
2021-11-27vmxnet3: Use generic Kconfig option for page size limitGuenter Roeck
Use the architecture independent Kconfig option PAGE_SIZE_LESS_THAN_64KB to indicate that VMXNET3 requires a page size smaller than 64kB. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
drivers/net/ipa/ipa_main.c 8afc7e471ad3 ("net: ipa: separate disabling setup from modem stop") 76b5fbcd6b47 ("net: ipa: kill ipa_modem_init()") Duplicated include, drop one. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26net: dsa: microchip: implement multi-bridge supportOleksij Rempel
Current driver version is able to handle only one bridge at time. Configuring two bridges on two different ports would end up shorting this bridges by HW. To reproduce it: ip l a name br0 type bridge ip l a name br1 type bridge ip l s dev br0 up ip l s dev br1 up ip l s lan1 master br0 ip l s dev lan1 up ip l s lan2 master br1 ip l s dev lan2 up Ping on lan1 and get response on lan2, which should not happen. This happened, because current driver version is storing one global "Port VLAN Membership" and applying it to all ports which are members of any bridge. To solve this issue, we need to handle each port separately. This patch is dropping the global port member storage and calculating membership dynamically depending on STP state and bridge participation. Note: STP support was broken before this patch and should be fixed separately. Fixes: c2e866911e25 ("net: dsa: microchip: break KSZ9477 DSA driver into two files") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26net: mscc: ocelot: correctly report the timestamping RX filters in ethtoolVladimir Oltean
The driver doesn't support RX timestamping for non-PTP packets, but it declares that it does. Restrict the reported RX filters to PTP v2 over L2 and over L4. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26net: mscc: ocelot: set up traps for PTP packetsVladimir Oltean
IEEE 1588 support was declared too soon for the Ocelot switch. Out of reset, this switch does not apply any special treatment for PTP packets, i.e. when an event message is received, the natural tendency is to forward it by MAC DA/VLAN ID. This poses a problem when the ingress port is under a bridge, since user space application stacks (written primarily for endpoint ports, not switches) like ptp4l expect that PTP messages are always received on AF_PACKET / AF_INET sockets (depending on the PTP transport being used), and never being autonomously forwarded. Any forwarding, if necessary (for example in Transparent Clock mode) is handled in software by ptp4l. Having the hardware forward these packets too will cause duplicates which will confuse endpoints connected to these switches. So PTP over L2 barely works, in the sense that PTP packets reach the CPU port, but they reach it via flooding, and therefore reach lots of other unwanted destinations too. But PTP over IPv4/IPv6 does not work at all. This is because the Ocelot switch have a separate destination port mask for unknown IP multicast (which PTP over IP is) flooding compared to unknown non-IP multicast (which PTP over L2 is) flooding. Specifically, the driver allows the CPU port to be in the PGID_MC port group, but not in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from Allan Nielsen which explain that the embedded MIPS CPU on Ocelot switches is not very powerful at all, so every penny they could save by not allowing flooding to the CPU port module matters. Unknown IP multicast did not make it. The de facto consensus is that when a switch is PTP-aware and an application stack for PTP is running, switches should have some sort of trapping mechanism for PTP packets, to extract them from the hardware data path. This avoids both problems: (a) PTP packets are no longer flooded to unwanted destinations (b) PTP over IP packets are no longer denied from reaching the CPU since they arrive there via a trap and not via flooding It is not the first time when this change is attempted. Last time, the feedback from Allan Nielsen and Andrew Lunn was that the traps should not be installed by default, and that PTP-unaware switching may be desired for some use cases: https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/ To address that feedback, the present patch adds the necessary packet traps according to the RX filter configuration transmitted by user space through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we keep 5 filters, which are amended each time RX timestamping is enabled or disabled on a port: - 1 for PTP over L2 - 2 for PTP over IPv4 (UDP ports 319 and 320) - 2 for PTP over IPv6 (UDP ports 319 and 320) The cookie by which these filters (invisible to tc) are identified is strategically chosen such that it does not collide with the filters used for the ocelot-8021q tagging protocol by the Felix driver, or with the MRP traps set up by the Ocelot library. Other alternatives were considered, like patching user space to do something, but there are so many ways in which PTP packets could be made to reach the CPU, generically speaking, that "do what?" is a very valid question. The ptp4l program from the linuxptp stack already attempts to do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into a dev_mc_add() on the interface, in the kernel: https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73 https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c Reality shows that this is not sufficient in case the interface belongs to a switchdev driver, as dev_mc_add() does not show the intention to trap a packet to the CPU, but rather the intention to not drop it (it is strictly for RX filtering, same as promiscuous does not mean to send all traffic to the CPU, but to not drop traffic with unknown MAC DA). This topic is a can of worms in itself, and it would be great if user space could just stay out of it. On the other hand, setting up PTP traps privately within the driver is not new by any stretch of the imagination: https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833 https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050 https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21 So this is the approach taken here as well. The difference here being that we prepare and destroy the traps per port, dynamically at runtime, as opposed to driver init time, because apparently, PTP-unaware forwarding is a use case. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Reported-by: Po Liu <po.liu@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2026-09-11 17:16:39 +0000