| Age | Commit message (Collapse) | Author |
|---|
|
Instead of using lp->ndev.parent to find the correct device to use for
DMA API calls, just use the dev attribute in the device structure.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.
If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.
This failure mode has not actually been observed, but was found as part
of other driver updates.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The trailing tag is also supported by this family. The default is still
rtl8_4 but now the switch supports changing the tag to rtl8_4t.
Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on
static allocation of IRQ resources in DT core code, this
causes an issue when using hierarchical interrupt domains
using "interrupts" property in the node as this bypassed
the hierarchical setup and messed up the irq chaining.
In preparation for removal of static setup of IRQ resource
from DT core code use platform_get_irq().
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Link: https://lore.kernel.org/r/20220303100815.25605-1-tangmeng@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This PHY doesn't support a link-up interrupt source. If aneg is enabled
we use the "aneg complete" interrupt for this purpose, but if aneg is
disabled link-up isn't signaled currently.
According to a vendor driver there's an additional "energy detect"
interrupt source that can be used to signal link-up if aneg is disabled.
We can safely ignore this interrupt source if aneg is enabled.
This patch was tested on a TX3 Mini TV box with S905W (even though
boot message says it's a S905D).
This issue has been existing longer, but due to changes in phylib and
the driver the patch applies only from the commit marked as fixed.
Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/04cac530-ea1b-850e-6cfa-144a55c4d75d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variables 'res' inside the functions sparx5_ptp_get_1ppm and
sparx5_ptp_get_nominal_value was not initialized. So in case of the default
case of the switch after, it would return an uninitialized variable.
This makes also the clang builds to failed.
Fixes: 0933bd04047c3b ("net: sparx5: Add support for ptp clocks")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220304140918.3356873-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the starting value in the for loop is greater than or equal to 1,
the restriction is CAS_FLAG_REG_PLUS is in the file cassini.h is
defined as 0x1 by macro, and the for loop and if condition is not
satisfied, so the code here is redundant.
Clean up the following smatch warning:
drivers/net/ethernet/sun/cassini.c:3513 cas_start_dma() warn: we never
enter this loop.
drivers/net/ethernet/sun/cassini.c:1239 cas_init_rx_dma() warn: we never
enter this loop.
drivers/net/ethernet/sun/cassini.c:1247 cas_init_rx_dma() warn: we never
enter this loop.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds zero-copy Rx and Tx support for AF_XDP sockets. It do so
by adding a separate NAPI poll function that is attached to a each
channel when the XSK socket is attached with XDP_SETUP_XSK_POOL, and
restored when the XSK socket is terminated, this is done per channel.
Support for XDP_TX is implemented and the XDP buffer can safely be moved
from the Rx to the Tx queue and correctly freed and returned to the XSK
pool once it's transmitted.
Note that when AF_XDP zero-copy is enabled, the XDP action XDP_PASS
will allocate a new buffer and copy the zero-copy frame prior
passing it to the kernel stack.
This patch is based on previous work by Jakub Kicinski.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for adding AF_XDP support add a configuration check to
make sure the buffer size can not be set to a larger value then the XSK
socket chunk size.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each data path needs an array of xsk pools to track if an xsk socket is
in use. Add this array and make sure it's handled correctly when the
data path is duplicated.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There will be more NAPI register logic once AF_XDP support is
added, wrap our already conditional napi add/del into helpers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some common functionality that can be reused in the upcoming
AF_XDP support. Expose those functions in the header. While at it mark
some arguments of nfp_net_rx_csum() as const.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the function get_ts_info in ethtool_ops which is needed to get
the HW capabilities for timestamping.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing 2-step timestamping the HW will generate an interrupt when it
managed to timestamp a frame. It is the SW responsibility to read it
from the FIFO.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update both the extraction and injection to do timestamping of the
frames. The extraction is always doing the timestamping while for
injection is doing the timestamping only if it is configured.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the ioctl callbacks SIOCSHWTSTAMP and SIOCGHWTSTAMP to allow
to configure the ports to enable/disable timestamping for TX. The RX
timestamping is always enabled. The HW is capable to run both 1-step
timestamping and 2-step timestamping.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sparx5 has 3 PHC. Enable each of them, for now all the
timestamping is happening on the first PHC.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the registers that will be used to configure the PHC in the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ifh is not changed, it is fixed for each frame for each
port that is sent out. Move this on the stack because this ifh needs to
be change based on the frames that are send out. This is needed for PTP
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To configure the T1 phy as master or slave using the ethtool -s <dev>
master-slave <forced-master/forced-slave>, the config_aneg and read
status functions are added.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LAN937x T1 switch is based on LAN87xx Phy, so reusing the init script of
the LAN87xx. There is a workaround in accessing the DSP bank register
for LAN937x Phy. Whenever there is a bank switch to DSP registers, then
we need a one dummy read access before proceeding to the actual register
access.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new initialization sequence is the improvement to the existing init
routine. Init routine does soft reset, run init script and set
Hw_init. Added the new access_smi_poll_timeout() for polling smi
bank write.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed the empty lines in struct phy_drivers.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Used the PHY_ID_MATCH_MODEL MACRO for describing the phy_id and
phy_id_mask.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replaced the current code of resetting of LAN87xx phy to
genphy_soft_reset library function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 1588 in LAN8814 phy driver.
It supports 1-step and 2-step timestamping.
Co-developed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make Extended page register accessing atomic,
to overcome unexpected output from register
reads/writes.
Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34e3 ("net: macb: Re-enable RX interrupt only when RX is done")
Cc: stable@vger.kernel.org
Co-developed-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Łukasz Stelmach <l.stelmach@samsung.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-03-03
Jacob Keller says:
This series refactors the ice networking driver VF storage from a simple
static array to a hash table. It also introduces krefs and proper locking
and protection to prevent common use-after-free and concurrency issues.
There are two motivations for this work. First is to make the ice driver
more resilient by preventing a whole class of use-after-free bugs that can
occur around concurrent access to VF structures while removing VFs.
The second is to prepare the ice driver for future virtualization work to
support Scalable IOV, an alternative VF implementation compared to Single
Root IOV. The new VF implementation will allow for more dynamic VF creation
and removal, necessitating a more robust implementation for VF storage that
can't rely on the existing mechanisms to prevent concurrent access
violations.
The first few patches are cleanup and preparatory work needed to make the
conversion to the hash table safe. Following this preparatory work is a
patch to migrate the VF structures and variables to a new sub-structure for
code clarity. Next introduce new interface functions to abstract the VF
storage. Finally, the driver is actually converted to the hash table and
kref implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an apparently incorrect conflict resolution on my part in commit
54c319846086 ("net: mscc: ocelot: enforce FDB isolation when
VLAN-unaware"), "ocelot->ports[port]->is_dsa_8021q_cpu = false" was
supposed to be replaced by "ocelot_port_unset_dsa_8021q_cpu(ocelot, port)"
which does the same thing, and more. But now we have both, so the direct
assignment is redundant. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet extraction failures over register-based MMIO are silent, and
difficult to pinpoint. Add an error message to remedy this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Automated tools complain that felix_check_xtr_pkt() has logic to drain
the CPU queue on the reception of a PTP packet over Ethernet, yet it
returns an uninitialized error code in the case where the CPU queue was
empty.
This is not likely to happen (/possible if hardware works correctly),
but it isn't a fatal condition either. The PTP packet will be dequeued
from the CPU queue when the next PTP packet arrives. So initialize "err"
to 0 for the case where nothing was dequeued during this iteration.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA ->port_rxtstamp() function is never called for PTP_CLASS_NONE:
dsa_skb_defer_rx_timestamp:
if (type == PTP_CLASS_NONE)
return false;
if (likely(ds->ops->port_rxtstamp))
return ds->ops->port_rxtstamp(ds, p->dp->index, skb, type);
So practically, the argument is unused, so remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This assignment is redundant, since ocelot->npi has already been set to
-1 by felix_npi_port_deinit(). Call path:
felix_change_tag_protocol
-> felix_del_tag_protocol(DSA_TAG_PROTO_OCELOT)
-> felix_teardown_tag_npi
-> felix_npi_port_deinit
-> felix_set_tag_protocol(DSA_TAG_PROTO_OCELOT_8021Q)
-> felix_setup_tag_8021q
-> felix_8021q_cpu_port_init
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardcoding these IP protocol numbers in is2_entry_set() obscures the
purpose of the code, so replace the magic numbers with the definitions
from linux/in.h.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify ocelot_vcap_block_remove_filter by using list_for_each_entry
instead of list_for_each.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following coccicheck warning:
drivers/net/ethernet/marvell/mv643xx_eth.c:1664:35-36: WARNING opportunity for min()
Signed-off-by: Haowen Bai <baihaowen88@gmail.com>
Link: https://lore.kernel.org/r/1646271529-7659-1-git-send-email-baihaowen88@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ice driver stores VF structures in a simple array which is allocated
once at the time of VF creation. The VF structures are then accessed
from the array by their VF ID. The ID must be between 0 and the number
of allocated VFs.
Multiple threads can access this table:
* .ndo operations such as .ndo_get_vf_cfg or .ndo_set_vf_trust
* interrupts, such as due to messages from the VF using the virtchnl
communication
* processing such as device reset
* commands to add or remove VFs
The current implementation does not keep track of when all threads are
done operating on a VF and can potentially result in use-after-free
issues caused by one thread accessing a VF structure after it has been
released when removing VFs. Some of these are prevented with various
state flags and checks.
In addition, this structure is quite static and does not support a
planned future where virtualization can be more dynamic. As we begin to
look at supporting Scalable IOV with the ice driver (as opposed to just
supporting Single Root IOV), this structure is not sufficient.
In the future, VFs will be able to be added and removed individually and
dynamically.
To allow for this, and to better protect against a whole class of
use-after-free bugs, replace the VF storage with a combination of a hash
table and krefs to reference track all of the accesses to VFs through
the hash table.
A hash table still allows efficient look up of the VF given its ID, but
also allows adding and removing VFs. It does not require contiguous VF
IDs.
The use of krefs allows the cleanup of the VF memory to be delayed until
after all threads have released their reference (by calling ice_put_vf).
To prevent corruption of the hash table, a combination of RCU and the
mutex table_lock are used. Addition and removal from the hash table use
the RCU-aware hash macros. This allows simple read-only look ups that
iterate to locate a single VF can be fast using RCU. Accesses which
modify the hash table, or which can't take RCU because they sleep, will
hold the mutex lock.
By using this design, we have a stronger guarantee that the VF structure
can't be released until after all threads are finished operating on it.
We also pave the way for the more dynamic Scalable IOV implementation in
the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
net/batman-adv/hard-interface.c
commit 690bb6fb64f5 ("batman-adv: Request iflink once in batadv-on-batadv check")
commit 6ee3c393eeb7 ("batman-adv: Demote batadv-on-batadv skip error message")
https://lore.kernel.org/all/20220302163049.101957-1-sw@simonwunderlich.de/
net/smc/af_smc.c
commit 4d08b7b57ece ("net/smc: Fix cleanup when register ULP fails")
commit 462791bbfa35 ("net/smc: add sysctl interface for SMC")
https://lore.kernel.org/all/20220302112209.355def40@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before we switch the VF data structure storage mechanism to a hash,
introduce new accessor functions to define the new interface.
* ice_get_vf_by_id is a function used to obtain a reference to a VF from
the table based on its VF ID
* ice_has_vfs is used to quickly check if any VFs are configured
* ice_get_num_vfs is used to get an exact count of how many VFs are
configured
We can drop the old ice_validate_vf_id function, since every caller was
just going to immediately access the VF table to get a reference
anyways. This way we simply use the single ice_get_vf_by_id to both
validate the VF ID is within range and that there exists a VF with that
ID.
This change enables us to more easily convert the codebase to the hash
table since most callers now properly use the interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We maintain a number of values for VFs within the ice_pf structure. This
includes the VF table, the number of allocated VFs, the maximum number
of supported SR-IOV VFs, the number of queue pairs per VF, the number of
MSI-X vectors per VF, and a bitmap of the VFs with detected MDD events.
We're about to add a few more variables to this list. Clean this up
first by extracting these members out into a new ice_vfs structure
defined in ice_virtchnl_pf.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_for_each_vf macro is intended to be used to loop over all VFs.
The current implementation relies on an iterator that is the index into
the VF array in the PF structure. This forces all users to perform a
look up themselves.
This abstraction forces a lot of duplicate work on callers and leaks the
interface implementation to the caller. Replace this with an
implementation that includes the VF pointer the primary iterator. This
version simplifies callers which just want to iterate over every VF, as
they no longer need to perform their own lookup.
The "i" iterator value is replaced with a new unsigned int "bkt"
parameter, as this will match the necessary interface for replacing
the VF array with a hash table. For now, the bkt is the VF ID, but in
the future it will simply be the hash bucket index. Document that it
should not be treated as a VF ID.
This change aims to simplify switching from the array to a hash table. I
considered alternative implementations such as an xarray but decided
that the hash table was the simplest and most suitable implementation. I
also looked at methods to hide the bkt iterator entirely, but I couldn't
come up with a feasible solution that worked for hash table iterators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When removing VFs, the driver takes a weird approach of assigning
pf->num_alloc_vfs to 0 before iterating over the VFs using a temporary
variable.
This logic has been in the driver for a long time, and seems to have
been carried forward from i40e.
We want to refactor the way VFs are stored, and iterating over the data
structure without the ice_for_each_vf interface impedes this work.
The logic relies on implicitly using the num_alloc_vfs as a sort of
"safe guard" for accessing VF data.
While this sort of guard makes sense for Single Root IOV where all VFs
are added at once, the data structures don't work for VFs which can be
added and removed dynamically. We also have a separate state flag,
ICE_VF_DEINIT_IN_PROGRESS which is a stronger protection against
concurrent removal and access.
Avoid the custom tmp iteration and replace it with the standard
ice_for_each_vf iterator. Delay the assignment of num_alloc_vfs until
after this loop finishes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_send_msg_to_vf function is used by the PF to send a response
to a VF. This function has overzealous checks to ensure its not passed a
NULL VF pointer and to ensure that the passed in struct ice_vf has a
valid vf_id sub-member.
These checks have existed since commit 1071a8358a28 ("ice: Implement
virtchnl commands for AVF support") and function as simple sanity
checks.
We are planning to refactor the ice driver to use a hash table along
with appropriate locks in a future refactor. This change will modify how
the ice_validate_vf_id function works. Instead of a simple >= check to
ensure the VF ID is between some range, it will check the hash table to
see if the specified VF ID is actually in the table. This requires that
the function properly lock the table to prevent race conditions.
The checks may seem ok at first glance, but they don't really provide
much benefit.
In order for ice_vc_send_msg_to_vf to have these checks fail, the
callers must either (1) pass NULL as the VF, (2) construct an invalid VF
pointer manually, or (3) be using a VF pointer which becomes invalid
after they obtain it properly using ice_get_vf_by_id.
For (1), a cursory glance over callers of ice_vc_send_msg_to_vf can show
that in most cases the functions already operate assuming their VF
pointer is valid, such as by derferencing vf->pf or other members.
They obtain the VF pointer by accessing the VF array using the VF ID,
which can never produce a NULL value (since its a simple address
operation on the array it will not be NULL.
The sole exception for (1) is that ice_vc_process_vf_msg will forward a
NULL VF pointer to this function as part of its goto error handler
logic. This requires some minor cleanup to simply exit immediately when
an invalid VF ID is detected (Rather than use the same error flow as
the rest of the function).
For (2), it is unexpected for a flow to construct a VF pointer manually
instead of accessing the VF array. Defending against this is likely to
just hide bad programming.
For (3), it is definitely true that VF pointers could become invalid,
for example if a thread is processing a VF message while the VF gets
removed. However, the correct solution is not to add additional checks
like this which do not guarantee to prevent the race. Instead we plan to
solve the root of the problem by preventing the possibility entirely.
This solution will require the change to a hash table with proper
locking and reference counts of the VF structures. When this is done,
ice_validate_vf_id will require locking of the hash table. This will be
problematic because all of the callers of ice_vc_send_msg_to_vf will
already have to take the lock to obtain the VF pointer anyways. With a
mutex, this leads to a double lock that could hang the kernel thread.
Avoid this by removing the checks which don't provide much value, so
that we can safely add the necessary protections properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After removing all VFs, the driver clears the VFLR indication for VFs.
This has been in ice since the beginning of SR-IOV support in the ice
driver.
The implementation was copied from i40e, and the motivation for the VFLR
indication clearing is described in the commit f7414531a0cf ("i40e:
acknowledge VFLR when disabling SR-IOV")
The commit explains that we need to clear the VFLR indication because
the virtual function undergoes a VFLR event. If we don't indicate that
it is complete it can cause an issue when VFs are re-enabled due to
a "phantom" VFLR.
The register block read was added under a pci_vfs_assigned check
originally. This was done because we added the check after calling
pci_disable_sriov. This was later moved to disable SRIOV earlier in the
flow so that the VF drivers could be torn down before we removed
functionality.
Move the VFLR acknowledge into the main loop that tears down VF
resources. This avoids using the tmp value for iterating over VFs
multiple times. The result will make it easier to refactor the VF array
in a future change.
It's possible we might want to modify this flow to also stop checking
pci_vfs_assigned. However, it seems reasonable to keep this change: we
should only clear the VFLR if we actually disabled SR-IOV.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_mbx_clear_malvf function is used to clear the indication and
count of how many times a VF was detected as malicious. During
ice_free_vfs, we use this function to ensure that all removed VFs are
reset to a clean state.
The call currently is done at the end of ice_free_vfs() using a tmp
value to iterate over all of the entries in the bitmap.
This separate iteration using tmp is problematic for a planned refactor
of the VF array data structure. To avoid this, lets move the call
slightly higher into the function inside the loop where we teardown all
of the VFs. This avoids one use of the tmp value used for iteration.
We'll fix the other user in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
