summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2022-03-17rtw89: add config_rf_reg_v1 to configure RF parameter tablesPing-Ke Shih
The format of RF parameter is changed; it doesn't encode delay parameters into table, but the delay coding becomes regular pair of register address and value. To help firmware to recover RF register settings, we need to download these parameters to firmware. For v1 format, only download partial parameters (ignore them with addr < 0x100). Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220317055543.40514-6-pkshih@realtek.com
2022-03-17rtw89: 8852c: add read/write rf register functionChung-Hsuan Hung
Using encoded address which BIT(16) is used to discriminate which region is going to access. Illustrate the calling flow as below rtw89_phy_write_rf_v1() -+-> rtw89_phy_write_rf() // old interface +-> rtw89_phy_write_rf_a() // new interface Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220317055543.40514-5-pkshih@realtek.com
2022-03-17rtw89: 8852c: add setting of TB UL TX power offsetYuan-Han Zhang
Configure this TX power to indicate TX power offset that uses to transmit TB (trigger base) uplink frames. Also, shrink the unit of TX power offset changes to suitable type s8. Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220317055543.40514-4-pkshih@realtek.com
2022-03-17rtw89: 8852c: add write/read crystal function in CFO trackingYuan-Han Zhang
The CFO tracking algorithm is the same, but control methods are different. Set parameters via xtal serial interfaces (SI). Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220317055543.40514-3-pkshih@realtek.com
2022-03-17rtw89: modify dcfo_comp to share with chipsYuan-Han Zhang
The dcfo_comp is digital CFO (central frequency offset) compensation. Since the flow can be shared with all chips, add chip parameters to support variant register address and format. Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220317055543.40514-2-pkshih@realtek.com
2022-03-17rtw89: Fix spelling mistake "Mis-Match" -> "Mismatch"Colin Ian King
There are some spelling mistakes in some literal strings. Fix them. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220316234242.55515-1-colin.i.king@gmail.com
2022-03-17brcmfmac: p2p: Fix spelling mistake "Comback" -> "Comeback"Colin Ian King
There are some spelling mistakes in comments and brcmf_dbg messages. Fix these. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220316233938.55135-1-colin.i.king@gmail.com
2022-03-17iwlwifi: mei: fix building iwlmeiArnd Bergmann
Building iwlmei without CONFIG_CFG80211 causes a link-time warning: ld.lld: error: undefined symbol: ieee80211_hdrlen >>> referenced by net.c >>> net/wireless/intel/iwlwifi/mei/net.o:(iwl_mei_tx_copy_to_csme) in archive drivers/built-in.a Add an explicit dependency to avoid this. In theory it should not be needed here, but it also seems pointless to allow IWLMEI for configurations without CFG80211. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Emmanuel Grumbach <Emmanuel.grumbach@intel.com> Acked-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220316183617.1470631-1-arnd@kernel.org
2022-03-17net: stmmac: clean up impossible conditionDan Carpenter
This code works but it has a static checker warning: drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1687 init_dma_rx_desc_rings() warn: always true condition '(queue >= 0) => (0-u32max >= 0)' Obviously, it makes no sense to check if an unsigned int is >= 0. What prevents this code from being a forever loop is that later there is a separate check for if (queue == 0). The "queue" variable is less than MTL_MAX_RX_QUEUES (8) so it can easily fit in an int type. Any larger value for "queue" would lead to an array overflow when we assign "rx_q = &priv->rx_queue[queue]". Fixes: de0b90e52a11 ("net: stmmac: rearrange RX and TX desc init into per-queue basis") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220316083744.GB30941@kili Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-17net: geneve: support IPv4/IPv6 as inner protocolEyal Birger
This patch adds support for encapsulating IPv4/IPv6 within GENEVE. In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs to be provided at device creation. This property cannot be changed for the time being. In case IP traffic is received on a non-tun device the drop count is increased. Signed-off-by: Eyal Birger <eyal.birger@gmail.com> Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-17net: mvneta: Add support for 98DX2530 Ethernet portChris Packham
The 98DX2530 SoC is similar to the Armada 3700 except it needs a different MBUS window configuration. Add a new compatible string to identify this device and the required MBUS window configuration. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-16net/mlx5e: MPLSoUDP encap, support action vlan pop_eth explicitlyMaor Dickman
Currently the MPLSoUDP encap offload does the L2 pop implicitly while adding such action explicitly (vlan eth_push) will cause the rule to not be offloaded. Solve it by adding offload support for vlan eth_push in case of MPLSoUDP decap case. Flow example: filter root protocol ip pref 1 flower chain 0 filter root protocol ip pref 1 flower chain 0 handle 0x1 eth_type ipv4 dst_ip 2.2.2.22 src_ip 2.2.2.21 in_hw in_hw_count 1 action order 1: vlan pop_eth pipe index 1 ref 1 bind 1 used_hw_stats delayed action order 2: mpls push protocol mpls_uc label 555 tc 3 ttl 255 pipe index 1 ref 1 bind 1 used_hw_stats delayed action order 3: tunnel_key set src_ip 8.8.8.21 dst_ip 8.8.8.22 dst_port 6635 csum tos 0x4 ttl 6 pipe index 1 ref 1 bind 1 used_hw_stats delayed action order 4: mirred (Egress Redirect to device bareudp0) stolen index 1 ref 1 bind 1 used_hw_stats delayed Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16net/mlx5e: MPLSoUDP decap, use vlan push_eth instead of peditMaor Dickman
Currently action pedit of source and destination MACs is used to fill the MACs in L2 push step in MPLSoUDP decap offload, this isn't aligned to tc SW which use vlan eth_push action to do this. To fix that, offload support for vlan veth_push action is added together with mpls pop action, and deprecate the use of pedit of MACs. Flow example: filter protocol mpls_uc pref 1 flower chain 0 filter protocol mpls_uc pref 1 flower chain 0 handle 0x1 eth_type 8847 mpls_label 555 enc_dst_port 6635 in_hw in_hw_count 1 action order 1: tunnel_key unset pipe index 2 ref 1 bind 1 used_hw_stats delayed action order 2: mpls pop protocol ip pipe index 2 ref 1 bind 1 used_hw_stats delayed action order 3: vlan push_eth dst_mac de:a2:ec:d6:69:c8 src_mac de:a2:ec:d6:69:c8 pipe index 2 ref 1 bind 1 used_hw_stats delayed action order 4: mirred (Egress Redirect to device enp8s0f0_0) stolen index 2 ref 1 bind 1 used_hw_stats delayed Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16net: mv643xx_eth: undo some opreations in mv643xx_eth_probeMinghao Chi
Cannot directly return platform_get_irq return irq, there are operations that need to be undone. Fixes: bf2b83425b59 ("net: mv643xx_eth: use platform_get_irq() instead of platform_get_resource()") Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220316012444.2126070-1-chi.minghao@zte.com.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16net: hns3: Fix spelling mistake "does't" -> "doesn't"Colin Ian King
There is a spelling mistake in a dev_warn message. Fix it. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20220315222914.2960786-1-colin.i.king@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16gve: Fix spelling mistake "droping" -> "dropping"Colin Ian King
There is a spelling mistake in a netdev_warn warning. Fix it. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20220315222615.2960504-1-colin.i.king@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16net: ksz884x: optimize netdev_open flow and remove static variablewujunwen
remove the static next_jiffies variable, and reinitialize next_jiffies to simplify netdev_open Signed-off-by: wujunwen <wudaemon@163.com> Link: https://lore.kernel.org/r/20220315122857.78601-1-wudaemon@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16hamradio: Fix wrong assignment of 'bbc->cfg.loopback'Meng Tang
In file hamradio/baycom_epp.c, the baycom_setmode interface, there is a problem with improper use of strstr. Suppose that when modestr="noloopback", both conditions which are 'strstr(modestr,"noloopback")' and 'strstr(modestr,"loopback")' will be true(not NULL), this lead the bc->cfg.loopback variable will be first assigned to 0, and then reassigned to 1. This will cause 'bc->cfg.loopback = 0' will never take effect. That obviously violates the logic of the code, so adjust the order of their execution to solve the problem. Signed-off-by: Meng Tang <tangmeng@uniontech.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220315074851.6456-1-tangmeng@uniontech.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16bareudp: use ipv6_mod_enabled to check if IPv6 enabledHangbin Liu
bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled. But if user start kernel with ipv6.disable=1, the bareudp sock will created failed, which cause the interface open failed even with ethertype ip. e.g. # ip link add bareudp1 type bareudp dstport 2 ethertype ip # ip link set bareudp1 up RTNETLINK answers: Address family not supported by protocol Fix it by using ipv6_mod_enabled() to check if IPv6 enabled. There is no need to check IS_ENABLED(CONFIG_IPV6) as ipv6_mod_enabled() will return false when CONFIG_IPV6 no enabled in include/linux/ipv6.h. Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20220315062618.156230-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16Merge tag 'linux-can-next-for-5.18-20220316' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2022-03-16 the first 3 patches are by Oliver Hartkopp target the CAN ISOTP protocol and fix a problem found by syzbot in isotp_bind(), return -EADDRNOTAVAIL in unbound sockets in isotp_recvmsg() and add support for MSG_TRUNC to isotp_recvmsg(). Amit Kumar Mahapatra converts the xilinx,can device tree bindings to yaml. The last patch is by Julia Lawall and fixes typos in the ucan driver. * tag 'linux-can-next-for-5.18-20220316' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: can: ucan: fix typos in comments dt-bindings: can: xilinx_can: Convert Xilinx CAN binding to YAML can: isotp: support MSG_TRUNC flag when reading from socket can: isotp: return -EADDRNOTAVAIL when reading from unbound socket can: isotp: sanitize CAN ID checks in isotp_bind() ==================== Link: https://lore.kernel.org/r/20220316204710.716341-1-mkl@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16can: ucan: fix typos in commentsJulia Lawall
Various spelling mistakes in comments. Detected with the help of Coccinelle. Link: https://lore.kernel.org/all/20220314115354.144023-28-Julia.Lawall@inria.fr Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-03-16mt76: fix monitor rx FCS error in DFS channelDeren Wu
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to fw for channel config. This would cause rx performance bad while monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would get the same performance as normal channels. Reviewed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: don't enable beacon filter when IEEE80211_CONF_CHANGE_MONITOR ↵Sean Wang
is set IEEE80211_CONF_CHANGE_MONITOR would be set every time even when vif runs as sta mode. If vif runs as sta mode, the beacon filter would be falsely enabled earlier than the associated state. That is not the behavior the firmware expects and also breaks the original logic of sta mode. Thus, we only limit the operation to set the beacon filter only for monitor mode when IEEE80211_CONF_CHANGE_MONITOR is set. Fixes: 4ad65a54617c ("mt76: mt7921: toggle runtime-pm adding a monitor vif") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: fix wrong HE data rate in sniffer toolDeren Wu
Due to the missing IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN in status report, the HE rate in wirehsark/tcpdump always shows wrong value. Applications will refer to IEEE80211_RADIOTAP_HE_DATA5_DATA_BW_RU_ALLOC when the flag is set and shows the correct data rate. Reviewed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7915: introduce 802.11ax multi-bss supportLorenzo Bianconi
Introduce mbss mcu APIs to enable 802.11ax multi-bss AP support for mt7915 devices Tested-by: Money Wang <money.wang@mediatek.com> Co-developed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Co-developed-by: Money Wang <money.wang@mediatek.com> Signed-off-by: Money Wang <money.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16devlink: pass devlink_port to port_split / port_unsplit callbacksJakub Kicinski
Now that devlink ports are protected by the instance lock it seems natural to pass devlink_port as an argument to the port_split / port_unsplit callbacks. This should save the drivers from doing a lookup. In theory drivers may have supported unsplitting ports which were not registered prior to this change. Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16devlink: hold the instance lock in port_split / port_unsplit callbacksJakub Kicinski
Let the core take the devlink instance lock around port splitting and remove the now redundant locking in the drivers. Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16eth: mlxsw: switch to explicit locking for port registrationJakub Kicinski
Explicitly lock the devlink instance and use devl_ API. This will be used by the subsequent patch to invoke .port_split / .port_unsplit callbacks with devlink instance lock held. Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16eth: nfp: replace driver's "pf" lock with devlink instance lockJakub Kicinski
The whole reason for existence of the pf mutex is that we could not lock the devlink instance around port splitting. There are more types of reconfig which can make ports appear or disappear. Now that the devlink instance lock is exposed to drivers and "locked" helpers exist we can switch to using the devlink lock directly. Next patches will move the locking inside .port_(un)split to the core. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16eth: nfp: wrap locking assertions in helpersJakub Kicinski
We can replace the PF lock with devlink instance lock in subsequent changes. To make the patches easier to comprehend and limit line lengths - factor out the existing locking assertions. No functional changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16Merge tag 'wireless-2022-03-16' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless Kalle Valo says: ==================== wireless fixes for v5.17 Third set of fixes for v5.17. We have only one revert to fix an ath10k regression. * tag 'wireless-2022-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: Revert "ath10k: drop beacon and probe response which leak from other channel" ==================== Link: https://lore.kernel.org/r/20220316130249.B5225C340EC@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-16ice: add trace events for tx timestampsJacob Keller
We've previously run into many issues related to the latency of a Tx timestamp completion with the ice hardware. It can be difficult to determine the root cause of a slow Tx timestamp. To aid in this, introduce new trace events which capture timing data about when the driver reaches certain points while processing a transmit timestamp * ice_tx_tstamp_request: Trace when the stack initiates a new timestamp request. * ice_tx_tstamp_fw_req: Trace when the driver begins a read of the timestamp register in the work thread. * ice_tx_tstamp_fw_done: Trace when the driver finishes reading a timestamp register in the work thread. * ice_tx_tstamp_complete: Trace when the driver submits the skb back to the stack with a completed Tx timestamp. These trace events can be enabled using the standard trace event subsystem exposed by the ice driver. If they are disabled, they become no-ops with no run time cost. The following is a simple GNU AWK script which can highlight one potential way to use the trace events to capture latency data from the trace buffer about how long the driver takes to process a timestamp: ----- BEGIN { PREC=256 } # Detect requests /tx_tstamp_request/ { time=strtonum($4) skb=$7 # Store the time of request for this skb requests[skb] = time printf("skb %s: idx %d at %.6f\n", skb, idx, time) } # Detect completions /tx_tstamp_complete/ { time=strtonum($4) skb=$7 idx=$9 if (skb in requests) { latency = (time - requests[skb]) * 1000 printf("skb %s: %.3f to complete\n", skb, latency) if (latency > 4) { printf(">>> HIGH LATENCY <<<\n") } printf("\n") } else { printf("!!! skb %s (idx %d) at %.6f\n", skb, idx, time) } } ----- Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-03-16ice: fix return value check in ice_gnss.cYang Yingliang
kthread_create_worker() and tty_alloc_driver() return ERR_PTR() and never return NULL. The NULL test in the return value check should be replaced with IS_ERR(). Fixes: 43113ff73453 ("ice: add TTY for GNSS module for E810T device") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-03-16ice: Fix inconsistent indenting in ice_switchWojciech Drewek
Fix the following warning as reported by smatch: smatch warnings: drivers/net/ethernet/intel/ice/ice_switch.c:5568 ice_find_dummy_packet() warn: inconsistent indenting Fixes: 9a225f81f540 ("ice: Support GTP-U and GTP-C offload in switchdev") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-03-16mt76: mt7921: move mt7921_init_hw in a dedicated workLorenzo Bianconi
Firmware initialization can take a while. Move mt7921_init_hw routine in a dedicated work in order to not slow down bootstrap process. Tested-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: add mt7921u driverLorenzo Bianconi
Introduce support for MT7921U 802.11ax 2x2:2SS wireless devices. Tested-by: Sean Wang <sean.wang@mediatek.com> Tested-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: move mt7921_usb_sdio_tx_status_data in mac common code.Lorenzo Bianconi
This is a preliminary patch to add mt7921u driver support. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: move mt7921_usb_sdio_tx_complete_skb in common mac code.Lorenzo Bianconi
This is a preliminary patch to add mt7921u driver support. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: move mt7921_usb_sdio_tx_prepare_skb in common mac codeLorenzo Bianconi
This is a preliminary patch to add mt7921u driver support. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: update mt7921_skb_add_usb_sdio_hdr to support usbLorenzo Bianconi
This is a preliminary patch to add mt7921u driver support. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7921: disable runtime pm for usbLorenzo Bianconi
Runtime-pm is not currently supported by usb driver Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: usb: introduce __mt76u_init utility routineLorenzo Bianconi
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops into mt7615 module in order to allow specifying driver specific parameter. This is a preliminary patch to add usb support to mt7921 driver. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: usb: add req_type to ___mt76u_wr signatureLorenzo Bianconi
This is a preliminary patch to add usb support to mt7921 driver. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: usb: add req_type to ___mt76u_rr signatureLorenzo Bianconi
This is a preliminary patch to add usb support to mt7921 driver. Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7915: fix typos in commentsJulia Lawall
Various spelling mistakes in comments. Detected with the help of Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7915: fix phy cap in mt7915_set_stream_he_txbf_caps()Peter Chiu
This patch fixes performance issue of beamforming tx on bandwidth 160MHz. Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986") Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7915: fix beamforming mib statsShayne Chen
Some of beamforming mib counters are moved to different offsets or registers in newer chipsets. Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986") Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: mt7915: set band1 TGID field in tx descriptorShayne Chen
Set proper group index of tx descriptor for band1. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: fix invalid rssi reportDeren Wu
Drop invalid rssi value to calculate a reasonable report Fixes: 4550fb9e9810 ("mt76: improve signal strength reporting") Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-16mt76: use le32/16_get_bits() whenever possibleRyder Lee
Switch to use le32/16_get_bits() to simplfy codes and specify the size explicitly to avoid potential issues. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2026-09-08 08:43:52 +0000