summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2022-10-19wifi: rtw89: phy: add dummy C2H handler to avoid warning messagePing-Ke Shih
The C2H class 2 function 3 is to report retry count of low rate, but driver doesn't implement yet, so add a dummy case to avoid message: rtw89_8852be 0000:03:00.0: c2h class 2 not support Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221014060237.29050-4-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: add chip_ops related to RF calibrationPing-Ke Shih
Since RF calibrations are added, add chip_ops to call them. These chip_ops include initial, full calibration, configuration when switching band and scanning, and track work in period of 2 seconds. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221014060237.29050-3-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: rfk: add DPKPing-Ke Shih
DPK is short for digital pre-distortion calibration. It can adjusts digital waveform according to PA linear characteristics dynamically to enhance TX EVM. Do this calibration when we are going to run on AP channel. To prevent power offset out of boundary, it monitors thermal and set proper boundary to register. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221014060237.29050-2-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: rfk: add TSSIPing-Ke Shih
TSSI is transmitter signal strength indication, which is a close-loop hardware circuit to feedback actual transmitting power as a reference for next transmission. When we setup channel to connect an AP, it does full calibration. When switching bands or channels, it needs to reset hardware status to prevent use wrong feedback of previous transmission. To do TX power compensation reflecting current temperature, it loads tables of compensation values into registers according to channel and band group. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221012083234.20224-6-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: rfk: add IQKPing-Ke Shih
IQ signal calibration is a very important calibration to yield good RF performance. We do this calibration only if we are going to run on AP channel. During scanning phase, without this calibration RF performance is still acceptable because it transmits with low data rate at this phase. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221012083234.20224-5-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: rfk: add RX DCKPing-Ke Shih
RX DCK is receiver DC calibration. With this calibration, we have proper DC offset to reflect correct received signal strength indicator. Do this calibration when bringing up interface and going to run on AP channel. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221012083234.20224-4-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: rfk: add RCKPing-Ke Shih
RCK is synchronize RC calibration. Driver triggers this calibration and sets the result to register. This calibration is needed once when interface is going to up. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221012083234.20224-3-pkshih@realtek.com
2022-10-19wifi: rtw89: 8852b: rfk: add DACKPing-Ke Shih
DACK (digital-to-analog converters calibration) is used to calibrate DAC to output good quality signals. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221012083234.20224-2-pkshih@realtek.com
2022-10-19wifi: ath10k: Delay the unmapping of the bufferYoughandhar Chintala
On WCN3990, we are seeing a rare scenario where copy engine hardware is sending a copy complete interrupt to the host driver while still processing the buffer that the driver has sent, this is leading into an SMMU fault triggering kernel panic. This is happening on copy engine channel 3 (CE3) where the driver normally enqueues WMI commands to the firmware. Upon receiving a copy complete interrupt, host driver will immediately unmap and frees the buffer presuming that hardware has processed the buffer. In the issue case, upon receiving copy complete interrupt, host driver will unmap and free the buffer but since hardware is still accessing the buffer (which in this case got unmapped in parallel), SMMU hardware will trigger an SMMU fault resulting in a kernel panic. In order to avoid this, as a work around, add a delay before unmapping the copy engine source DMA buffer. This is conditionally done for WCN3990 and only for the CE3 channel where issue is seen. Below is the crash signature: wifi smmu error: kernel: [ 10.120965] arm-smmu 15000000.iommu: Unhandled context fault: fsr=0x402, iova=0x7fdfd8ac0, fsynr=0x500003,cbfrsynra=0xc1, cb=6 arm-smmu 15000000.iommu: Unhandled context fault:fsr=0x402, iova=0x7fe06fdc0, fsynr=0x710003, cbfrsynra=0xc1, cb=6 qcom-q6v5-mss 4080000.remoteproc: fatal error received: err_qdi.c:1040:EF:wlan_process:0x1:WLAN RT:0x2091: cmnos_thread.c:3998:Asserted in copy_engine.c:AXI_ERROR_DETECTED:2149 remoteproc remoteproc0: crash detected in 4080000.remoteproc: type fatal error <3> remoteproc remoteproc0: handling crash #1 in 4080000.remoteproc pc : __arm_lpae_unmap+0x500/0x514 lr : __arm_lpae_unmap+0x4bc/0x514 sp : ffffffc011ffb530 x29: ffffffc011ffb590 x28: 0000000000000000 x27: 0000000000000000 x26: 0000000000000004 x25: 0000000000000003 x24: ffffffc011ffb890 x23: ffffffa762ef9be0 x22: ffffffa77244ef00 x21: 0000000000000009 x20: 00000007fff7c000 x19: 0000000000000003 x18: 0000000000000000 x17: 0000000000000004 x16: ffffffd7a357d9f0 x15: 0000000000000000 x14: 00fd5d4fa7ffffff x13: 000000000000000e x12: 0000000000000000 x11: 00000000ffffffff x10: 00000000fffffe00 x9 : 000000000000017c x8 : 000000000000000c x7 : 0000000000000000 x6 : ffffffa762ef9000 x5 : 0000000000000003 x4 : 0000000000000004 x3 : 0000000000001000 x2 : 00000007fff7c000 x1 : ffffffc011ffb890 x0 : 0000000000000000 Call trace: __arm_lpae_unmap+0x500/0x514 __arm_lpae_unmap+0x4bc/0x514 __arm_lpae_unmap+0x4bc/0x514 arm_lpae_unmap_pages+0x78/0xa4 arm_smmu_unmap_pages+0x78/0x104 __iommu_unmap+0xc8/0x1e4 iommu_unmap_fast+0x38/0x48 __iommu_dma_unmap+0x84/0x104 iommu_dma_free+0x34/0x50 dma_free_attrs+0xa4/0xd0 ath10k_htt_rx_free+0xc4/0xf4 [ath10k_core] ath10k_core_stop+0x64/0x7c [ath10k_core] ath10k_halt+0x11c/0x180 [ath10k_core] ath10k_stop+0x54/0x94 [ath10k_core] drv_stop+0x48/0x1c8 [mac80211] ieee80211_do_open+0x638/0x77c [mac80211] ieee80211_open+0x48/0x5c [mac80211] __dev_open+0xb4/0x174 __dev_change_flags+0xc4/0x1dc dev_change_flags+0x3c/0x7c devinet_ioctl+0x2b4/0x580 inet_ioctl+0xb0/0x1b4 sock_do_ioctl+0x4c/0x16c compat_ifreq_ioctl+0x1cc/0x35c compat_sock_ioctl+0x110/0x2ac __arm64_compat_sys_ioctl+0xf4/0x3e0 el0_svc_common+0xb4/0x17c el0_svc_compat_handler+0x2c/0x58 el0_svc_compat+0x8/0x2c Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221012142733.32420-1-quic_youghand@quicinc.com
2022-10-18enic: define constants for legacy interrupts offsetGovindarajulu Varadarajan
Use macro instead of function calls. These values are constant and will not change. Signed-off-by: Govindarajulu Varadarajan <govind.varadar@gmail.com> Link: https://lore.kernel.org/r/20221018005804.188643-1-govind.varadar@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-18net: fec: remove the unused functionsShenwei Wang
Removed those unused functions since we simplified the driver by using the page pool to manage RX buffers. Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Link: https://lore.kernel.org/r/20221017161236.1563975-1-shenwei.wang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-18net: remove smc911x driverArnd Bergmann
This driver was used on Arm and SH machines until 2009, when the last platforms moved to the smsc911x driver for the same hardware. Time to retire this version. Link: https://lore.kernel.org/netdev/1232010482-3744-1-git-send-email-steve.glendinning@smsc.com/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20221017121900.3520108-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-18ionic: catch NULL pointer issue on reconfigBrett Creeley
It's possible that the driver will dereference a qcq that doesn't exist when calling ionic_reconfigure_queues(), which causes a page fault BUG. If a reduction in the number of queues is followed by a different reconfig such as changing the ring size, the driver can hit a NULL pointer when trying to clean up non-existent queues. Fix this by checking to make sure both the qcqs array and qcq entry exists bofore trying to use and free the entry. Fixes: 101b40a0171f ("ionic: change queue count with no reset") Signed-off-by: Brett Creeley <brett@pensando.io> Signed-off-by: Shannon Nelson <snelson@pensando.io> Link: https://lore.kernel.org/r/20221017233123.15869-1-snelson@pensando.io Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-18bnxt_en: fix memory leak in bnxt_nvm_test()Vikas Gupta
Free the kzalloc'ed buffer before returning in the success path. Fixes: 5b6ff128fdf6 ("bnxt_en: implement callbacks for devlink selftests") Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/1666020742-25834-1-git-send-email-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-17net: ethernet: mediatek: ppe: Remove the unused function mtk_foe_entry_usable()Jiapeng Chong
The function mtk_foe_entry_usable() is defined in the mtk_ppe.c file, but not called elsewhere, so delete this unused function. drivers/net/ethernet/mediatek/mtk_ppe.c:400:20: warning: unused function 'mtk_foe_entry_usable'. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2409 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-17net: ethernet: mtk_eth_wed: add missing of_node_put()Yang Yingliang
The device_node pointer returned by of_parse_phandle() with refcount incremented, when finish using it, the refcount need be decreased. Fixes: 804775dfc288 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-17net: ethernet: mtk_eth_wed: add missing put_device() in mtk_wed_add_hw()Yang Yingliang
After calling get_device() in mtk_wed_add_hw(), in error path, put_device() needs be called. Fixes: 804775dfc288 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-17net: ethernet: mtk_eth_soc: fix possible memory leak in mtk_probe()Yang Yingliang
If mtk_wed_add_hw() has been called, mtk_wed_exit() needs be called in error path or removing module to free the memory allocated in mtk_wed_add_hw(). Fixes: 804775dfc288 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-16Merge tag 'random-6.1-rc1-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random Pull more random number generator updates from Jason Donenfeld: "This time with some large scale treewide cleanups. The intent of this pull is to clean up the way callers fetch random integers. The current rules for doing this right are: - If you want a secure or an insecure random u64, use get_random_u64() - If you want a secure or an insecure random u32, use get_random_u32() The old function prandom_u32() has been deprecated for a while now and is just a wrapper around get_random_u32(). Same for get_random_int(). - If you want a secure or an insecure random u16, use get_random_u16() - If you want a secure or an insecure random u8, use get_random_u8() - If you want secure or insecure random bytes, use get_random_bytes(). The old function prandom_bytes() has been deprecated for a while now and has long been a wrapper around get_random_bytes() - If you want a non-uniform random u32, u16, or u8 bounded by a certain open interval maximum, use prandom_u32_max() I say "non-uniform", because it doesn't do any rejection sampling or divisions. Hence, it stays within the prandom_*() namespace, not the get_random_*() namespace. I'm currently investigating a "uniform" function for 6.2. We'll see what comes of that. By applying these rules uniformly, we get several benefits: - By using prandom_u32_max() with an upper-bound that the compiler can prove at compile-time is ≤65536 or ≤256, internally get_random_u16() or get_random_u8() is used, which wastes fewer batched random bytes, and hence has higher throughput. - By using prandom_u32_max() instead of %, when the upper-bound is not a constant, division is still avoided, because prandom_u32_max() uses a faster multiplication-based trick instead. - By using get_random_u16() or get_random_u8() in cases where the return value is intended to indeed be a u16 or a u8, we waste fewer batched random bytes, and hence have higher throughput. This series was originally done by hand while I was on an airplane without Internet. Later, Kees and I worked on retroactively figuring out what could be done with Coccinelle and what had to be done manually, and then we split things up based on that. So while this touches a lot of files, the actual amount of code that's hand fiddled is comfortably small" * tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: prandom: remove unused functions treewide: use get_random_bytes() when possible treewide: use get_random_u32() when possible treewide: use get_random_{u8,u16}() when possible, part 2 treewide: use get_random_{u8,u16}() when possible, part 1 treewide: use prandom_u32_max() when possible, part 2 treewide: use prandom_u32_max() when possible, part 1
2022-10-15net: stmmac: Enable mac_managed_pm phylink configShenwei Wang
Enable the mac_managed_pm configuration in the phylink_config structure to avoid the kernel warning during system resume. Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-15net: phylink: add mac_managed_pm in phylink_config structureShenwei Wang
The recent commit 'commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")' requires the MAC driver explicitly tell the phy driver who is managing the PM, otherwise you will see warning during resume stage. Add a boolean property in the phylink_config structure so that the MAC driver can use it to tell the PHY driver if it wants to manage the PM. Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-15sunhme: Uninitialized variable in happy_meal_init()Dan Carpenter
The "burst" string is only initialized for CONFIG_SPARC. It should be set to "64" because that's what is used by PCI. Fixes: 24cddbc3ef11 ("sunhme: Combine continued messages") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-15net: phy: dp83867: Extend RX strap quirk for SGMII modeHarini Katakam
When RX strap in HW is not set to MODE 3 or 4, bit 7 and 8 in CF4 register should be set. The former is already handled in dp83867_config_init; add the latter in SGMII specific initialization. Fixes: 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy") Signed-off-by: Harini Katakam <harini.katakam@amd.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-15net: hv_netvsc: Fix a warning triggered by memcpy in rndis_filterCezar Bulinaru
memcpy: detected field-spanning write (size 168) of single field "(void *)&request->response_msg + (sizeof(struct rndis_message) - sizeof(union rndis_message_container)) + sizeof(*req_id)" at drivers/net/hyperv/rndis_filter.c:338 (size 40) RSP: 0018:ffffc90000144de0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff8881766b4000 RCX: 0000000000000000 RDX: 0000000000000102 RSI: 0000000000009ffb RDI: 00000000ffffffff RBP: ffffc90000144e38 R08: 0000000000000000 R09: 00000000ffffdfff R10: ffffc90000144c48 R11: ffffffff82f56ac8 R12: ffff8881766b403c R13: 00000000000000a8 R14: ffff888100b75000 R15: ffff888179301d00 FS: 0000000000000000(0000) GS:ffff8884d6280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055f8b024c418 CR3: 0000000176548001 CR4: 00000000003706e0 Call Trace: <IRQ> ? _raw_spin_unlock_irqrestore+0x27/0x50 netvsc_poll+0x556/0x940 [hv_netvsc] __napi_poll+0x2e/0x170 net_rx_action+0x299/0x2f0 __do_softirq+0xed/0x2ef __irq_exit_rcu+0x9f/0x110 irq_exit_rcu+0xe/0x20 sysvec_hyperv_callback+0xb0/0xd0 </IRQ> <TASK> asm_sysvec_hyperv_callback+0x1b/0x20 RIP: 0010:native_safe_halt+0xb/0x10 Fixes: A warning triggered when the response message len exceeds the size of rndis_message. Inside the rndis_request structure these fields are however followed by a RNDIS_EXT_LEN padding so it is safe to use unsafe_memcpy. Reviewed-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Cezar Bulinaru <cbulinaru@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-15sfc: Change VF mac via PF as first preference if available.Jonathan Cooper
Changing a VF's mac address through the VF (rather than via the PF) fails with EPERM because the latter part of efx_ef10_set_mac_address attempts to change the vport mac address list as the VF. Even with this fixed it still fails with EBUSY because the vadaptor is still assigned on the VF - the vadaptor reassignment must be within a section where the VF has torn down its state. A major reason this has broken is because we have two functions that ostensibly do the same thing - have a PF and VF cooperate to change a VF mac address. Rather than do this, if we are changing the mac of a VF that has a link to the PF in the same VM then simply call sriov_set_vf_mac instead, which is a proven working function that does that. If there is no PF available, or that fails non-fatally, then attempt to change the VF's mac address as we would a PF, without updating the PF's data. Test case: Create a VF: echo 1 > /sys/class/net/<if>/device/sriov_numvfs Set the mac address of the VF directly: ip link set <vf> addr 00:11:22:33:44:55 Set the MAC address of the VF via the PF: ip link set <pf> vf 0 mac 00:11:22:33:44:66 Without this patch the last command will fail with ENOENT. Signed-off-by: Jonathan Cooper <jonathan.s.cooper@amd.com> Reported-by: Íñigo Huguet <ihuguet@redhat.com> Fixes: 910c8789a777 ("set the MAC address using MC_CMD_VADAPTOR_SET_MAC") Acked-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-14net: macvlan: change schedule system_wq to system_unbound_wqzhangxiangqian
For FT2000+/64 devices, when four virtual machines share the same physical network interface, DROP will occur due to the single core CPU performance problem. ip_check_defrag and macvlan_process_broadcast is on the same CPU. When the MACVLAN PORT increases, the CPU usage reaches more than 90%. bc_queue > bc_queue_len_used (default 1000), causing DROP. Signed-off-by: zhangxiangqian <zhangxiangqian@kylinos.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-14i40e: Fix DMA mappings leakJan Sokolowski
During reallocation of RX buffers, new DMA mappings are created for those buffers. steps for reproduction: while : do for ((i=0; i<=8160; i=i+32)) do ethtool -G enp130s0f0 rx $i tx $i sleep 0.5 ethtool -g enp130s0f0 done done This resulted in crash: i40e 0000:01:00.1: Unable to allocate memory for the Rx descriptor ring, size=65536 Driver BUG WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:141 xdp_rxq_info_unreg+0x43/0x50 Call Trace: i40e_free_rx_resources+0x70/0x80 [i40e] i40e_set_ringparam+0x27c/0x800 [i40e] ethnl_set_rings+0x1b2/0x290 genl_family_rcv_msg_doit.isra.15+0x10f/0x150 genl_family_rcv_msg+0xb3/0x160 ? rings_fill_reply+0x1a0/0x1a0 genl_rcv_msg+0x47/0x90 ? genl_family_rcv_msg+0x160/0x160 netlink_rcv_skb+0x4c/0x120 genl_rcv+0x24/0x40 netlink_unicast+0x196/0x230 netlink_sendmsg+0x204/0x3d0 sock_sendmsg+0x4c/0x50 __sys_sendto+0xee/0x160 ? handle_mm_fault+0xbe/0x1e0 ? syscall_trace_enter+0x1d3/0x2c0 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x5b/0x1a0 entry_SYSCALL_64_after_hwframe+0x65/0xca RIP: 0033:0x7f5eac8b035b Missing register, driver bug WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:119 xdp_rxq_info_unreg_mem_model+0x69/0x140 Call Trace: xdp_rxq_info_unreg+0x1e/0x50 i40e_free_rx_resources+0x70/0x80 [i40e] i40e_set_ringparam+0x27c/0x800 [i40e] ethnl_set_rings+0x1b2/0x290 genl_family_rcv_msg_doit.isra.15+0x10f/0x150 genl_family_rcv_msg+0xb3/0x160 ? rings_fill_reply+0x1a0/0x1a0 genl_rcv_msg+0x47/0x90 ? genl_family_rcv_msg+0x160/0x160 netlink_rcv_skb+0x4c/0x120 genl_rcv+0x24/0x40 netlink_unicast+0x196/0x230 netlink_sendmsg+0x204/0x3d0 sock_sendmsg+0x4c/0x50 __sys_sendto+0xee/0x160 ? handle_mm_fault+0xbe/0x1e0 ? syscall_trace_enter+0x1d3/0x2c0 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x5b/0x1a0 entry_SYSCALL_64_after_hwframe+0x65/0xca RIP: 0033:0x7f5eac8b035b This was caused because of new buffers with different RX ring count should substitute older ones, but those buffers were freed in i40e_configure_rx_ring and reallocated again with i40e_alloc_rx_bi, thus kfree on rx_bi caused leak of already mapped DMA. Fix this by reallocating ZC with rx_bi_zc struct when BPF program loads. Additionally reallocate back to rx_bi when BPF program unloads. If BPF program is loaded/unloaded and XSK pools are created, reallocate RX queues accordingly in XSP_SETUP_XSK_POOL handler. Fixes: be1222b585fd ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings") Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Chandan <chandanx.rout@intel.com> (A Contingent Worker at Intel) Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-14net: dsa: qca8k: fix ethtool autocast mib for big-endian systemsChristian Marangi
The switch sends autocast mib in little-endian. This is problematic for big-endian system as the values needs to be converted. Fix this by converting each mib value to cpu byte order. Fixes: 5c957c7ca78c ("net: dsa: qca8k: add support for mib autocast in Ethernet packet") Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-14net: dsa: qca8k: fix inband mgmt for big-endian systemsChristian Marangi
The header and the data of the skb for the inband mgmt requires to be in little-endian. This is problematic for big-endian system as the mgmt header is written in the cpu byte order. Fix this by converting each value for the mgmt header and data to little-endian, and convert to cpu byte order the mgmt header and data sent by the switch. Fixes: 5950c7c0a68c ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet") Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-13Merge tag 'net-6.1-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from netfilter, and wifi. Current release - regressions: - Revert "net/sched: taprio: make qdisc_leaf() see the per-netdev-queue pfifo child qdiscs", it may cause crashes when the qdisc is reconfigured - inet: ping: fix splat due to packet allocation refactoring in inet - tcp: clean up kernel listener's reqsk in inet_twsk_purge(), fix UAF due to races when per-netns hash table is used Current release - new code bugs: - eth: adin1110: check in netdev_event that netdev belongs to driver - fixes for PTR_ERR() vs NULL bugs in driver code, from Dan and co. Previous releases - regressions: - ipv4: handle attempt to delete multipath route when fib_info contains an nh reference, avoid oob access - wifi: fix handful of bugs in the new Multi-BSSID code - wifi: mt76: fix rate reporting / throughput regression on mt7915 and newer, fix checksum offload - wifi: iwlwifi: mvm: fix double list_add at iwl_mvm_mac_wake_tx_queue (other cases) - wifi: mac80211: do not drop packets smaller than the LLC-SNAP header on fast-rx Previous releases - always broken: - ieee802154: don't warn zero-sized raw_sendmsg() - ipv6: ping: fix wrong checksum for large frames - mctp: prevent double key removal and unref - tcp/udp: fix memory leaks and races around IPV6_ADDRFORM - hv_netvsc: fix race between VF offering and VF association message Misc: - remove -Warray-bounds silencing in the drivers, compilers fixed" * tag 'net-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits) sunhme: fix an IS_ERR() vs NULL check in probe net: marvell: prestera: fix a couple NULL vs IS_ERR() checks kcm: avoid potential race in kcm_tx_work tcp: Clean up kernel listener's reqsk in inet_twsk_purge() net: phy: micrel: Fixes FIELD_GET assertion openvswitch: add nf_ct_is_confirmed check before assigning the helper tcp: Fix data races around icsk->icsk_af_ops. ipv6: Fix data races around sk->sk_prot. tcp/udp: Call inet6_destroy_sock() in IPv6 sk->sk_destruct(). udp: Call inet6_destroy_sock() in setsockopt(IPV6_ADDRFORM). tcp/udp: Fix memory leak in ipv6_renew_options(). mctp: prevent double key removal and unref selftests: netfilter: Fix nft_fib.sh for all.rp_filter=1 netfilter: rpfilter/fib: Populate flowic_l3mdev field selftests: netfilter: Test reverse path filtering net/mlx5: Make ASO poll CQ usable in atomic context tcp: cdg: allow tcp_cdg_release() to be called multiple times inet: ping: fix recent breakage ipv6: ping: fix wrong checksum for large frames net: ethernet: ti: am65-cpsw: set correct devlink flavour for unused ports ...
2022-10-13sunhme: fix an IS_ERR() vs NULL check in probeDan Carpenter
The devm_request_region() function does not return error pointers, it returns NULL on error. Fixes: 914d9b2711dd ("sunhme: switch to devres") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Link: https://lore.kernel.org/r/Y0bWzJL8JknX8MUf@kili Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-13net: marvell: prestera: fix a couple NULL vs IS_ERR() checksDan Carpenter
The __prestera_nexthop_group_create() function returns NULL on error and the prestera_nexthop_group_get() returns error pointers. Fix these two checks. Fixes: 0a23ae237171 ("net: marvell: prestera: Add router nexthops ABI") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/Y0bWq+7DoKK465z8@kili Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-13Merge tag 'wireless-2022-10-13' of ↵Paolo Abeni
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless Johannes Berg says: ==================== More wireless fixes for 6.1 This has only the fixes for the scan parsing issues. * tag 'wireless-2022-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: wifi: cfg80211: update hidden BSSes to avoid WARN_ON wifi: mac80211: fix crash in beacon protection for P2P-device wifi: mac80211_hwsim: avoid mac80211 warning on bad rate wifi: cfg80211: avoid nontransmitted BSS list corruption wifi: cfg80211: fix BSS refcounting bugs wifi: cfg80211: ensure length byte is present before access wifi: mac80211: fix MBSSID parsing use-after-free wifi: cfg80211/mac80211: reject bad MBSSID elements wifi: cfg80211: fix u8 overflow in cfg80211_update_notlisted_nontrans() ==================== Link: https://lore.kernel.org/r/20221013100522.46346-1-johannes@sipsolutions.net Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-10-13Merge branch 'cve-fixes-2022-10-13'Johannes Berg
Pull in the fixes for various scan parsing bugs found by Sönke Huster by fuzzing.
2022-10-13wifi: ath10k: Check return value of ath10k_get_arvif() in ↵Peter Kosyh
ath10k_wmi_event_tdls_peer() Return value of a function ath10k_get_arvif() is dereferenced without checking for null in ath10k_wmi_event_tdls_peer(), but it is usually checked for this function. Make ath10k_wmi_event_tdls_peer() do check retval of ath10k_get_arvif(). Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by: Peter Kosyh <pkosyh@yandex.ru> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221003091217.322598-1-pkosyh@yandex.ru
2022-10-13wifi: ath11k: Fix firmware crash on vdev delete race conditionSowmiya Sree Elavalagan
Current code does not wait for vdev delete completion on vdev create failures and tries to send another vdev create followed by vdev set param to firmware with same vdev id. This causes firmware crash. Fix this crash by waiting for vdev delete completion on vdev create failures. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.6.0.1-00905-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221011095346.3901-1-quic_ssreeela@quicinc.com
2022-10-12net: phy: micrel: Fixes FIELD_GET assertionDivya Koppera
FIELD_GET() must only be used with a mask that is a compile-time constant. Mark the functions as __always_inline to avoid the problem. Fixes: 21b688dabecb6a ("net: phy: micrel: Cable Diag feature for lan8814 phy") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com> Link: https://lore.kernel.org/r/20221011095437.12580-1-Divya.Koppera@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-12ieee802154: atusb: add support for trac featureAlexander Aring
This patch adds support for reading the trac register if atusb firmware reports tx done. There is currently a feature to compare a sequence number, if the payload is 1 it tells the driver only the sequence number is available if it's two there is additional the trac status register as payload. Currently the atusb_in_good() function determines if it's a tx done or rx done if according the payload length. This patch is doing the same and assumes this behaviour. Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220905203412.1322947-10-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
2022-10-12mac802154: Drop IEEE802154_HW_RX_DROP_BAD_CKSUMMiquel Raynal
This IEEE802154_HW_RX_DROP_BAD_CKSUM flag was only used by hwsim to reflect the fact that it would not validate the checksum (FCS). So this was only useful while the only filtering level hwsim was capable of was "NONE". Now that the driver has been improved we no longer need this flag. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20221007085310.503366-7-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
2022-10-12ieee802154: hwsim: Implement address filteringMiquel Raynal
We have access to the address filters being theoretically applied, we also have access to the actual filtering level applied, so let's add a proper frame validation sequence in hwsim. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20221007085310.503366-6-miquel.raynal@bootlin.com [stefan@datenfreihafen.org: fixup some checkpatch warnings] Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
2022-10-12ieee802154: hwsim: Record the address filter valuesMiquel Raynal
As a first step, introduce a basic implementation for the ->set_hw_addr_filt() hook. In a second step, the values recorded here will be used to perform proper filtering during reception. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20221007085310.503366-5-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
2022-10-12net: ieee802154: mcr20a: Switch to use dev_err_probe() helperYang Yingliang
dev_err() can be replace with dev_err_probe() which will check if error code is -EPROBE_DEFER. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220915071258.678536-1-yangyingliang@huawei.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
2022-10-12net/mlx5: Make ASO poll CQ usable in atomic contextLeon Romanovsky
Poll CQ functions shouldn't sleep as they are called in atomic context. The following splat appears once the mlx5_aso_poll_cq() is used in such flow. BUG: scheduling while atomic: swapper/17/0/0x00000100 Modules linked in: sch_ingress openvswitch nsh mlx5_vdpa vringh vhost_iotlb vdpa mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core fuse [last unloaded: mlx5_core] CPU: 17 PID: 0 Comm: swapper/17 Tainted: G W 6.0.0-rc2+ #13 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0x34/0x44 __schedule_bug.cold+0x47/0x53 __schedule+0x4b6/0x670 ? hrtimer_start_range_ns+0x28d/0x360 schedule+0x50/0x90 schedule_hrtimeout_range_clock+0x98/0x120 ? __hrtimer_init+0xb0/0xb0 usleep_range_state+0x60/0x90 mlx5_aso_poll_cq+0xad/0x190 [mlx5_core] mlx5e_ipsec_aso_update_curlft+0x81/0xb0 [mlx5_core] xfrm_timer_handler+0x6b/0x360 ? xfrm_find_acq_byseq+0x50/0x50 __hrtimer_run_queues+0x139/0x290 hrtimer_run_softirq+0x7d/0xe0 __do_softirq+0xc7/0x272 irq_exit_rcu+0x87/0xb0 sysvec_apic_timer_interrupt+0x72/0x90 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x16/0x20 RIP: 0010:default_idle+0x18/0x20 Code: ae 7d ff ff cc cc cc cc cc cc cc cc cc cc cc cc cc cc 0f 1f 44 00 00 8b 05 b5 30 0d 01 85 c0 7e 07 0f 00 2d 0a e3 53 00 fb f4 <c3> 0f 1f 80 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 80 ad 01 00 RSP: 0018:ffff888100883ee0 EFLAGS: 00000242 RAX: 0000000000000001 RBX: ffff888100849580 RCX: 4000000000000000 RDX: 0000000000000001 RSI: 0000000000000083 RDI: 000000000008863c RBP: 0000000000000011 R08: 00000064e6977fa9 R09: 0000000000000001 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 default_idle_call+0x37/0xb0 do_idle+0x1cd/0x1e0 cpu_startup_entry+0x19/0x20 start_secondary+0xfe/0x120 secondary_startup_64_no_verify+0xcd/0xdb </TASK> softirq: huh, entered softirq 8 HRTIMER 00000000a97c08cb with preempt_count 00000100, exited with 00000000? Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-12net: ethernet: ti: am65-cpsw: set correct devlink flavour for unused portsMatthias Schiffer
am65_cpsw_nuss_register_ndevs() skips calling devlink_port_type_eth_set() for ports without assigned netdev, triggering the following warning when DEVLINK_PORT_TYPE_WARN_TIMEOUT elapses after 3600s: Type was not set for devlink port. WARNING: CPU: 0 PID: 129 at net/core/devlink.c:8095 devlink_port_type_warn+0x18/0x30 Fixes: 0680e20af5fb ("net: ethernet: ti: am65-cpsw: Fix devlink port register sequence") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-10-12wifi: ath11k: Send PME message during wakeup from D3coldBaochen Qiang
We are seeing system stuck on some specific platforms due to WLAN chip fails to wakeup from D3cold state. With this flag, firmware will send PME message during wakeup and this issue is gone. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221010033237.415478-1-quic_bqiang@quicinc.com
2022-10-12wifi: ath11k: add support to configure channel dwell timeManikanta Pubbisetty
Add support to configure channel dwell time during scan. Dwell time help to stay on the channel for a specified duration during scan and aid userspace in finding WiFi networks. Very useful in passive scans where longer dwell times are needed to find the WiFi networks. Configure channel dwell time from duration of the scan request received from mac80211 when the duration is non-zero. When the scan request does not have duration value, use the default ones, the current implementation. Advertise corresponding feature flag NL80211_EXT_FEATURE_SET_SCAN_DWELL to enable the feature. Change is applicable for all ath11k hardware. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221007051130.6067-1-quic_mpubbise@quicinc.com
2022-10-12wifi: ath11k: suppress add interface errorKarthikeyan Periyasamy
In the VIF (other than monitor type) creation request, we should not throw the error code when the monitor VIF creation fails, since the actual VIF creation succeeds. If we throw the error code from driver then the actual VIF creation get fail. So suppress the monitor VIF creation error by throwing warning message instead of error code. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00760-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221006005842.8599-1-quic_periyasa@quicinc.com
2022-10-12wifi: ath11k: fix firmware assert during bandwidth change for peer staAditya Kumar Singh
Currently, ath11k sends peer assoc command for each peer to firmware when bandwidth changes. Peer assoc command is a bulky command and if many clients are connected, this could lead to firmware buffer getting overflowed leading to a firmware assert. However, during bandwidth change, only phymode and bandwidth also can be updated by WMI set peer param command. This makes the overall command light when compared to peer assoc and for multi-client cases, firmware buffer overflow also does not occur. Remove sending peer assoc command during sta bandwidth change and instead add sending WMI set peer param command for phymode and bandwidth. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Fixes: f187fe8e3bc65 ("ath11k: fix firmware crash during channel switch") Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221005095430.19890-1-quic_adisi@quicinc.com
2022-10-12wifi: ar5523: Fix use-after-free on ar5523_cmd() timed outShigeru Yoshida
syzkaller reported use-after-free with the stack trace like below [1]: [ 38.960489][ C3] ================================================================== [ 38.963216][ C3] BUG: KASAN: use-after-free in ar5523_cmd_tx_cb+0x220/0x240 [ 38.964950][ C3] Read of size 8 at addr ffff888048e03450 by task swapper/3/0 [ 38.966363][ C3] [ 38.967053][ C3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.0.0-09039-ga6afa4199d3d-dirty #18 [ 38.968464][ C3] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014 [ 38.969959][ C3] Call Trace: [ 38.970841][ C3] <IRQ> [ 38.971663][ C3] dump_stack_lvl+0xfc/0x174 [ 38.972620][ C3] print_report.cold+0x2c3/0x752 [ 38.973626][ C3] ? ar5523_cmd_tx_cb+0x220/0x240 [ 38.974644][ C3] kasan_report+0xb1/0x1d0 [ 38.975720][ C3] ? ar5523_cmd_tx_cb+0x220/0x240 [ 38.976831][ C3] ar5523_cmd_tx_cb+0x220/0x240 [ 38.978412][ C3] __usb_hcd_giveback_urb+0x353/0x5b0 [ 38.979755][ C3] usb_hcd_giveback_urb+0x385/0x430 [ 38.981266][ C3] dummy_timer+0x140c/0x34e0 [ 38.982925][ C3] ? notifier_call_chain+0xb5/0x1e0 [ 38.984761][ C3] ? rcu_read_lock_sched_held+0xb/0x60 [ 38.986242][ C3] ? lock_release+0x51c/0x790 [ 38.987323][ C3] ? _raw_read_unlock_irqrestore+0x37/0x70 [ 38.988483][ C3] ? __wake_up_common_lock+0xde/0x130 [ 38.989621][ C3] ? reacquire_held_locks+0x4a0/0x4a0 [ 38.990777][ C3] ? lock_acquire+0x472/0x550 [ 38.991919][ C3] ? rcu_read_lock_sched_held+0xb/0x60 [ 38.993138][ C3] ? lock_acquire+0x472/0x550 [ 38.994890][ C3] ? dummy_urb_enqueue+0x860/0x860 [ 38.996266][ C3] ? do_raw_spin_unlock+0x16f/0x230 [ 38.997670][ C3] ? dummy_urb_enqueue+0x860/0x860 [ 38.999116][ C3] call_timer_fn+0x1a0/0x6a0 [ 39.000668][ C3] ? add_timer_on+0x4a0/0x4a0 [ 39.002137][ C3] ? reacquire_held_locks+0x4a0/0x4a0 [ 39.003809][ C3] ? __next_timer_interrupt+0x226/0x2a0 [ 39.005509][ C3] __run_timers.part.0+0x69a/0xac0 [ 39.007025][ C3] ? dummy_urb_enqueue+0x860/0x860 [ 39.008716][ C3] ? call_timer_fn+0x6a0/0x6a0 [ 39.010254][ C3] ? cpuacct_percpu_seq_show+0x10/0x10 [ 39.011795][ C3] ? kvm_sched_clock_read+0x14/0x40 [ 39.013277][ C3] ? sched_clock_cpu+0x69/0x2b0 [ 39.014724][ C3] run_timer_softirq+0xb6/0x1d0 [ 39.016196][ C3] __do_softirq+0x1d2/0x9be [ 39.017616][ C3] __irq_exit_rcu+0xeb/0x190 [ 39.019004][ C3] irq_exit_rcu+0x5/0x20 [ 39.020361][ C3] sysvec_apic_timer_interrupt+0x8f/0xb0 [ 39.021965][ C3] </IRQ> [ 39.023237][ C3] <TASK> In ar5523_probe(), ar5523_host_available() calls ar5523_cmd() as below (there are other functions which finally call ar5523_cmd()): ar5523_probe() -> ar5523_host_available() -> ar5523_cmd_read() -> ar5523_cmd() If ar5523_cmd() timed out, then ar5523_host_available() failed and ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb() might touch the freed structure. This patch fixes this issue by canceling in-flight tx cmd if submitted urb timed out. Link: https://syzkaller.appspot.com/bug?id=9e12b2d54300842b71bdd18b54971385ff0d0d3a [1] Reported-by: syzbot+95001b1fd6dfcc716c29@syzkaller.appspotmail.com Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221009183223.420015-1-syoshida@redhat.com
2022-10-12wifi: carl9170: Remove -Warray-bounds exceptionKees Cook
GCC-12 emits false positive -Warray-bounds warnings with CONFIG_UBSAN_SHIFT (-fsanitize=shift). This is fixed in GCC 13[1], and there is top-level Makefile logic to remove -Warray-bounds for known-bad GCC versions staring with commit f0be87c42cbd ("gcc-12: disable '-Warray-bounds' universally for now"). Remove the local work-around. [1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=105679 Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221006192051.1742930-1-keescook@chromium.org
generated by cgit v1.2.3 (git 2.25.1) at 2026-09-06 23:08:38 +0000