| Age | Commit message (Collapse) | Author |
|---|
|
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a packet needs to be encapsulated towards a local destination IP, the
packet will undergo a "local bypass" and be injected into the Rx path as
if it was received by the target VXLAN device without undergoing
encapsulation. If such a device does not exist, the packet will be
dropped.
There are scenarios where we do not want to perform such a bypass, but
instead want the packet to be encapsulated and locally received by a
user space program for post-processing.
To that end, add a new VXLAN device attribute that controls whether a
"local bypass" is performed or not. Default to performing a bypass to
maintain existing behavior.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If available, interrogate the PHY to find out whether we can use it for
Wake-on-LAN. This can be a more power efficient way of implementing
that feature, especially when the MAC is powered off in low power
states.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for WAKE_UCAST, WAKE_MCAST, WAKE_BCAST, WAKE_MAGIC and
WAKE_MAGICSECURE. This is only supported with the BCM54210E and
compatible Ethernet PHYs. Using the in-band interrupt or an out of band
GPIO interrupts are supported.
Broadcom PHYs will generate a Wake-on-LAN level low interrupt on LED4 as
soon as one of the supported patterns is being matched. That includes
generating such an interrupt even if the PHY is operated during normal
modes. If WAKE_UCAST is selected, this could lead to the LED4 interrupt
firing up for every packet being received which is absolutely
undesirable from a performance point of view.
Because the Wake-on-LAN configuration can be set long before the system
is actually put to sleep, we cannot have an interrupt service routine to
clear on read the interrupt status register and ensure that new packet
matches will be detected.
It is desirable to enable the Wake-on-LAN interrupt as late as possible
during the system suspend process such that we limit the number of
interrupts to be handled by the system, but also conversely feed into
the Linux's system suspend way of dealing with interrupts in and around
the points of no return.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().
This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.
In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.
If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow efx_tc_encap_match entries to include a udp_sport and a
udp_sport_mask. As with enc_ip_tos, use pseudos to enforce that all
encap matches within a given <src_ip,dst_ip,udp_dport> tuple have
the same udp_sport_mask.
Note that since we use a single layer of pseudos for both fields, two
matches that differ in (say) udp_sport value aren't permitted to have
different ip_tos_mask, even though this would technically be safe.
Current userland TC does not support setting enc_src_port; this patch
was tested with an iproute2 patched to support it.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow efx_tc_encap_match entries to include an ip_tos and ip_tos_mask.
To avoid partially-overlapping Outer Rules (which can lead to undefined
behaviour in the hardware), store extra "pseudo" entries in our
encap_match hashtable, which are used to enforce that all Outer Rule
entries within a given <src_ip,dst_ip,udp_dport> tuple (or IPv6
equivalent) have the same ip_tos_mask.
The "direct" encap_match entry takes a reference on the "pseudo",
allowing it to be destroyed when all "direct" entries using it are
removed.
efx_tc_em_pseudo_type is an enum rather than just a bool because in
future an additional pseudo-type will be added to support Conntrack
offload.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently tc.c will block them before they get here, but following
patch will change that.
Use the extack message from efx_mae_check_encap_match_caps() instead
of writing a new one, since there's now more being fed in than just
an IP version.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When force-freeing leftover entries from our match_action_ht, call
efx_tc_delete_rule(), which releases all the rule's resources, rather
than open-coding it. The open-coded version was missing a call to
release the rule's encap match (if any).
It probably doesn't matter as everything's being torn down anyway, but
it's cleaner this way and prevents further error messages potentially
being logged by efx_tc_encap_match_free() later on.
Move efx_tc_flow_free() further down the file to avoid introducing a
forward declaration of efx_tc_delete_rule().
Fixes: 17654d84b47c ("sfc: add offloading of 'foreign' TC (decap) rules")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pointer variables of void * type do not require type cast.
Signed-off-by: wuych <yunchuan@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default we would not want RXFCS and RXALL features enabled as they are
mainly intended for debugging purposes. This does not stop users from
enabling them later on as needed.
Fixes: 8e57daf70671 ("sfc_ef100: RX path for EF100")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Co-developed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The type of the vlan_proto field is __be16.
And most users of the field use it as such.
In the case of setting or testing the field for the special VLAN_N_VID
value, host byte order is used. Which seems incorrect.
It also seems somewhat odd to store a VLAN ID value in a field that is
otherwise used to store Ether types.
Address this issue by defining BOND_VLAN_PROTO_NONE, a big endian value.
0xffff was chosen somewhat arbitrarily. What is important is that it
doesn't overlap with any valid VLAN Ether types.
I don't believe the problems described above are a bug because
VLAN_N_VID in both little-endian and big-endian byte order does not
conflict with any supported VLAN Ether types in big-endian byte order.
Reported by sparse as:
.../bond_main.c:2857:26: warning: restricted __be16 degrades to integer
.../bond_main.c:2863:20: warning: restricted __be16 degrades to integer
.../bond_main.c:2939:40: warning: incorrect type in assignment (different base types)
.../bond_main.c:2939:40: expected restricted __be16 [usertype] vlan_proto
.../bond_main.c:2939:40: got int
No functional changes intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As not all ICE_TX_FLAGS_* fit in current 16-bit limited
tx_flags field that was introduced in the Fixes commit,
VLAN-related information would be discarded completely.
As such, creating a vlan and trying to run ping through
would result in no traffic passing.
Fix that by refactoring tx_flags variable into flags only and
a separate variable that holds VLAN ID. As there is some space left,
type variable can fit between those two. Pahole reports no size
change to ice_tx_buf struct.
Fixes: aa1d3faf71a6 ("ice: Robustify cleaning/completing XDP Tx buffers")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ieee80211_ops::sta_rc_update must be atomic, because
ieee80211_chan_bw_change() holds rcu_read lock while calling
drv_sta_rc_update(), so create a work to do original things.
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 4621 at kernel/rcu/tree_plugin.h:318
rcu_note_context_switch+0x571/0x5d0
CPU: 0 PID: 4621 Comm: kworker/u16:2 Tainted: G W OE
Workqueue: phy3 ieee80211_chswitch_work [mac80211]
RIP: 0010:rcu_note_context_switch+0x571/0x5d0
Call Trace:
<TASK>
__schedule+0xb0/0x1460
? __mod_timer+0x116/0x360
schedule+0x5a/0xc0
schedule_timeout+0x87/0x150
? trace_raw_output_tick_stop+0x60/0x60
wait_for_completion_timeout+0x7b/0x140
usb_start_wait_urb+0x82/0x160 [usbcore
usb_control_msg+0xe3/0x140 [usbcore
rtw_usb_read+0x88/0xe0 [rtw_usb
rtw_usb_read8+0xf/0x10 [rtw_usb
rtw_fw_send_h2c_command+0xa0/0x170 [rtw_core
rtw_fw_send_ra_info+0xc9/0xf0 [rtw_core
drv_sta_rc_update+0x7c/0x160 [mac80211
ieee80211_chan_bw_change+0xfb/0x110 [mac80211
ieee80211_change_chanctx+0x38/0x130 [mac80211
ieee80211_vif_use_reserved_switch+0x34e/0x900 [mac80211
ieee80211_link_use_reserved_context+0x88/0xe0 [mac80211
ieee80211_chswitch_work+0x95/0x170 [mac80211
process_one_work+0x201/0x410
worker_thread+0x4a/0x3b0
? process_one_work+0x410/0x410
kthread+0xe1/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Cc: stable@vger.kernel.org
Fixes: c1edc86472fc ("rtw88: add ieee80211:sta_rc_update ops")
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/linux-wireless/f1e31e8e-f84e-3791-50fb-663a83c5c6e9@lwfinger.net/T/#t
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508085429.46653-1-pkshih@realtek.com
|
|
Though SER can recover this case, traffic can get stuck for a while. Fix it
by adjusting page quota to avoid hardware access null page of CMAC/DMAC.
Fixes: a1cb097168fa ("wifi: rtw89: 8852b: configure DLE mem")
Fixes: 3e870b481733 ("wifi: rtw89: 8852b: add HFC quota arrays")
Cc: stable@vger.kernel.org
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://github.com/lwfinger/rtw89/issues/226#issuecomment-1520776761
Link: https://github.com/lwfinger/rtw89/issues/240
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230426034737.24870-1-pkshih@realtek.com
|
|
The stats->tx_bytes shall subtract retry byte from tx byte.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/b3cd45596943cf5a06b2e08e2fe732ab0b51311b.1682285873.git.ryder.lee@mediatek.com
|
|
To avoid sparse warning:
sparse: warning: invalid assignment: |=
sparse: left side has type restricted __le32
sparse: right side has type unsigned lon
Fixes: 15ee62e73705 ("wifi: mt76: mt7996: enable BSS_CHANGED_BASIC_RATES support")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/16fa938373e3b145cb07a2c98d2428fea2abadba.1682285873.git.ryder.lee@mediatek.com
|
|
The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold},
remove it to silence the warning:
./drivers/net/ipvlan/ipvlan_core.c:559:3-11: WARNING: NULL check before dev_{put, hold} functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4930
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch corrects the NFP_NET_MAX_DSCP definition in the main.h file.
The incorrect definition result DSCP bits not being mapped properly when
DCB is set. When NFP_NET_MAX_DSCP was defined as 4, the next 60 DSCP
bits failed to be set.
Fixes: 9b7fe8046d74 ("nfp: add DCB IEEE support")
Cc: stable@vger.kernel.org
Signed-off-by: Huayu Chen <huayu.chen@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macsec hardware block supports XPN cipher suites also.
Hence added changes to offload XPN feature. Changes include
configuring SecY policy to XPN cipher suite, Salt and SSCI values.
64 bit packet number is passed instead of 32 bit packet number.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sxgbe_drv_remove() returned zero unconditionally, so it can be converted
to return void without losing anything. The upside is that it becomes
more obvious in its callers that there is no error to handle.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
write_reg(0x001F, 0x8000); //hard reset
write_reg(DSP_FFE_CFG, 0x0E81);
write_reg(0x001F, 0x4000); //soft reset
Since DP83867 PHY DM says "Changing this register to 0x0E81, will not
affect Long Cable performance.", enable the W/A by default.
Fixes: 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba21 ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Microchip ENC28J60 SPI Ethernet driver schedules a work item from
the interrupt handler because accesses to the SPI bus may sleep.
On PREEMPT_RT (which forces interrupt handling into threads) this
old-fashioned approach unnecessarily increases latency because an
interrupt results in first waking the interrupt thread, then scheduling
the work item. So, a double indirection to handle an interrupt.
Avoid by converting the driver to modern threaded interrupt handling.
Signed-off-by: Philipp Rosenberger <p.rosenberger@kunbus.com>
Signed-off-by: Zhi Han <hanzhi09@gmail.com>
[lukas: rewrite commit message, linewrap request_threaded_irq() call]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Link: https://lore.kernel.org/r/342380d989ce26bc49f0e5d45fbb0416a5f7809f.1683606193.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes. No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For 8852CE, there is abnormal state called CMDPSR_FRZTO,
which occasionally happens in some platforms, and could be
found by firmware and fixed in current SER flow, so we add
suppress function to avoid verbose message for this resolved case.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-4-pkshih@realtek.com
|
|
Newer FW re-design SER (syetem error recovery) L1 (level 1) flow.
New L1 flow will expect two extra states before original L1 flow.
* Before:
fw --- M1 --> driver
fw <-- M2 --- driver
fw --- M3 --> driver
fw <-- M4 --- driver
fw --- M5 --> driver
* After:
fw --- pre-M0 --> driver
fw <-- post-M0 --- driver
fw --- M1 --> driver
fw <-- M2 --- driver
fw --- M3 --> driver
fw <-- M4 --- driver
fw --- M5 --> driver
Then before M1, FW gets one more interval to deal with things that FW
should have handled well. To consider backward/forward compatibility,
FW and driver won't change flow from M1 to M5. (only except that halt
trigger control will change a little bit.) So, there will be two differnt
starting points of SER L1.
* old FW: SER L1 starts from M1
* new FW: SER L1 starts from pre-M0
Then, driver adds the new SER L1 entry and also keep the original one
instead of changing it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-3-pkshih@realtek.com
|
|
RTL8851B keeps almost the same interrupt flow as RTL8852A and RTL8852B.
But, it uses a different bitmask for interrupt indicator of FW HALT C2H.
So, we make a chip judgement in pci when configuring interrupt mask.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508084335.42953-2-pkshih@realtek.com
|
|
U-NII-4 band, i.e 5.9GHz channels, can be supported by chip 8852C, 8852B
and 8851B. But, it is not supported by chip 8852A. Flag support_unii4 is
added in chip info and defined by chip accordingly to indicate that.
We reference this flag of runtime chip to decide whether to register
5.9GHz channels.
After that, we consider if U-NII-4 band is allowed by our regulatory
rule of U-NII-4. If chip::support_unii4 but not regd::allow_unii4,
we stll do not register 5.9GHz channels.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-4-pkshih@realtek.com
|
|
For realtek regulatory, there are following two kinds of configurations
to determine whether to allow UNII-4 band, i.e. 5.9GHz channels.
1. default setting according to whether chip support it or not
2. evaluate realtek ACPI DSM with RTW89_ACPI_DSM_FUNC_59G_EN (func. 6)
If (1) is false, we won't try (2) and just disallow UNII-4. Otherwise,
if (2) is not supported or returns a non-specific value, we follow the
default setting either. Besides, this commit aims to add decision logic
in rtw89 regulatory. Actually, driver doesn't register UNII-4 yet. That
will be handled by another commit.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-3-pkshih@realtek.com
|
|
Introduce realtek ACPI DSM method to get required BIOS
configurations. It will be used in the following commits.
And, enum rtw89_acpi_dsm_func is added for listing the functions
which are currently recognized.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508081211.38760-2-pkshih@realtek.com
|
|
The type of "mwifiex_adapter->nd_info" is "struct cfg80211_wowlan_nd_info",
not "struct cfg80211_wowlan_nd_match".
Use struct_size() to ease the computation of the needed size.
The current code over-allocates some memory, so is safe.
But it wastes 32 bytes.
Fixes: 7d7f07d8c5d3 ("mwifiex: add wowlan net-detect support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7a6074fb056d2181e058a3cc6048d8155c20aec7.1683371982.git.christophe.jaillet@wanadoo.fr
|
|
Call mutex_unlock(&rtwdev->mutex); before returning on this error path.
Fixes: f0e741e4ddbc ("wifi: rtw88: add bitmap for dynamic port settings")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/ddd10a74-5982-4f65-8c59-c1cca558d239@kili.mountain
|
|
In recent access points, information element is longer as they include
additional data which exceeds 256 bytes. To accommodate longer
association response, increase the ASSOC response buffer.
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230509172811.4953-1-amisha.patel@microchip.com
|
|
Mandatory WFA testcase
CT_Security_WPA2Personal_STA_RSNEBoundsVerification-AbsentRSNCap,
performs bounds verfication on Beacon and/or Probe response frames. It
failed and observed the reason to be absence of cipher suite and AKM
suite in RSN information. To fix this, enable the RSN flag before extracting RSN
capabilities.
Fixes: cd21d99e595e ("wifi: wilc1000: validate pairwise and authentication suite offsets")
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421181005.4865-1-amisha.patel@microchip.com
|
|
Now that we no longer need to check whether the DMA address is within
the TSO header DMA memory range for the queue, we can allocate the TSO
header DMA memory in chunks rather than one contiguous order-6 chunk,
which can stress the kernel's memory subsystems to allocate.
Instead, use order-1 (8k) allocations, which will result in 32 order-1
pages containing 32 TSO headers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move tso_build_hdr() into mvneta_tso_put_hdr() so that all the TSO
header building code is in one place.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Now that we use a different buffer type for TSO headers, we can use
buf->type to determine whether the original buffer was DMA-mapped or
not. The rules are:
MVNETA_TYPE_XDP_TX - from a DMA pool, no unmap is required
MVNETA_TYPE_XDP_NDO - dma_map_single()'d
MVNETA_TYPE_SKB - normal skbuff, dma_map_single()'d
MVNETA_TYPE_TSO - from the TSO buffer area
This means we only need to call dma_unmap_single() on the XDP_NDO and
SKB types of buffer, and we no longer need the private IS_TSO_HEADER()
which relies on the TSO region being contiguously allocated.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Mark dma-mapped skbs and TSO buffers separately, so we can use
buf->type to identify their differences.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The transmit code assumes that the transmit descriptors that are used
begin with the first descriptor in the ring, but this may not be the
case. Fix this by providing a new function that dma-unmaps a range of
numbered descriptor entries, and use that to do the unmapping.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Below members are unused.
- td_tag member defined in struct ipc_pipe.
- adb_finish_timer & params defined in struct iosm_mux.
Remove it to avoid unexpected usage.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/92ee483d79dfc871ed7408da8fec60b395ff3a9c.1683649868.git.m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ipc_time_unit enum is defined but not used.
Remove it to avoid unexpected usage.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/8295a6138f13c686590ee4021384ee992f717408.1683649868.git.m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IOSM_IF_ID_PAYLOAD is defined but not used.
Remove it to avoid unexpected usage.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/0697e811cb7f10b4fd8f99e66bda1329efdd3d1d.1683649868.git.m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg
address, not offset") organized the stats counters for Ocelot chips, namely
the VSC7512 and VSC7514. A few of the counter offsets were incorrect, and
were caught by this warning:
WARNING: CPU: 0 PID: 24 at drivers/net/ethernet/mscc/ocelot_stats.c:909
ocelot_stats_init+0x1fc/0x2d8
reg 0x5000078 had address 0x220 but reg 0x5000079 has address 0x214,
bulking broken!
Fix these register offsets.
Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pointer variables of void * type do not require type cast.
Signed-off-by: wuych <yunchuan@nfschina.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now macsec on top of vlan can be offloaded to macsec offloading
devices so that VLAN tag is sent in clear text on wire i.e,
packet structure is DMAC|SMAC|VLAN|SECTAG. Offloading devices can
simply enable NETIF_F_HW_MACSEC feature in netdev->vlan_features for
this to work. But the logic in offloading drivers to retrieve the
private structure from netdev needs to be changed to check whether
the netdev received is real device or a vlan device and get private
structure accordingly. This patch changes the offloading drivers to
use helper macsec_netdev_priv instead of netdev_priv.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If skb enqueue the qdisc, fq_skb_cb(skb)->time_to_send is changed which
is actually skb->cb, and IPCB(skb_in)->opt will be used in
__ip_options_echo. It is possible that memcpy is out of bounds and lead
to stack overflow.
We should clear skb->cb before ip_local_out or ip6_local_out.
v2:
1. clean the stack info
2. use IPCB/IP6CB instead of skb->cb
crash on stable-5.10(reproduce in kasan kernel).
Stack info:
[ 2203.651571] BUG: KASAN: stack-out-of-bounds in
__ip_options_echo+0x589/0x800
[ 2203.653327] Write of size 4 at addr ffff88811a388f27 by task
swapper/3/0
[ 2203.655460] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted
5.10.0-60.18.0.50.h856.kasan.eulerosv2r11.x86_64 #1
[ 2203.655466] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-20181220_000000-szxrtosci10000 04/01/2014
[ 2203.655475] Call Trace:
[ 2203.655481] <IRQ>
[ 2203.655501] dump_stack+0x9c/0xd3
[ 2203.655514] print_address_description.constprop.0+0x19/0x170
[ 2203.655530] __kasan_report.cold+0x6c/0x84
[ 2203.655586] kasan_report+0x3a/0x50
[ 2203.655594] check_memory_region+0xfd/0x1f0
[ 2203.655601] memcpy+0x39/0x60
[ 2203.655608] __ip_options_echo+0x589/0x800
[ 2203.655654] __icmp_send+0x59a/0x960
[ 2203.655755] nf_send_unreach+0x129/0x3d0 [nf_reject_ipv4]
[ 2203.655763] reject_tg+0x77/0x1bf [ipt_REJECT]
[ 2203.655772] ipt_do_table+0x691/0xa40 [ip_tables]
[ 2203.655821] nf_hook_slow+0x69/0x100
[ 2203.655828] __ip_local_out+0x21e/0x2b0
[ 2203.655857] ip_local_out+0x28/0x90
[ 2203.655868] ipvlan_process_v4_outbound+0x21e/0x260 [ipvlan]
[ 2203.655931] ipvlan_xmit_mode_l3+0x3bd/0x400 [ipvlan]
[ 2203.655967] ipvlan_queue_xmit+0xb3/0x190 [ipvlan]
[ 2203.655977] ipvlan_start_xmit+0x2e/0xb0 [ipvlan]
[ 2203.655984] xmit_one.constprop.0+0xe1/0x280
[ 2203.655992] dev_hard_start_xmit+0x62/0x100
[ 2203.656000] sch_direct_xmit+0x215/0x640
[ 2203.656028] __qdisc_run+0x153/0x1f0
[ 2203.656069] __dev_queue_xmit+0x77f/0x1030
[ 2203.656173] ip_finish_output2+0x59b/0xc20
[ 2203.656244] __ip_finish_output.part.0+0x318/0x3d0
[ 2203.656312] ip_finish_output+0x168/0x190
[ 2203.656320] ip_output+0x12d/0x220
[ 2203.656357] __ip_queue_xmit+0x392/0x880
[ 2203.656380] __tcp_transmit_skb+0x1088/0x11c0
[ 2203.656436] __tcp_retransmit_skb+0x475/0xa30
[ 2203.656505] tcp_retransmit_skb+0x2d/0x190
[ 2203.656512] tcp_retransmit_timer+0x3af/0x9a0
[ 2203.656519] tcp_write_timer_handler+0x3ba/0x510
[ 2203.656529] tcp_write_timer+0x55/0x180
[ 2203.656542] call_timer_fn+0x3f/0x1d0
[ 2203.656555] expire_timers+0x160/0x200
[ 2203.656562] run_timer_softirq+0x1f4/0x480
[ 2203.656606] __do_softirq+0xfd/0x402
[ 2203.656613] asm_call_irq_on_stack+0x12/0x20
[ 2203.656617] </IRQ>
[ 2203.656623] do_softirq_own_stack+0x37/0x50
[ 2203.656631] irq_exit_rcu+0x134/0x1a0
[ 2203.656639] sysvec_apic_timer_interrupt+0x36/0x80
[ 2203.656646] asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 2203.656654] RIP: 0010:default_idle+0x13/0x20
[ 2203.656663] Code: 89 f0 5d 41 5c 41 5d 41 5e c3 cc cc cc cc cc cc cc
cc cc cc cc cc cc 0f 1f 44 00 00 0f 1f 44 00 00 0f 00 2d 9f 32 57 00 fb
f4 <c3> cc cc cc cc 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 54 be 08
[ 2203.656668] RSP: 0018:ffff88810036fe78 EFLAGS: 00000256
[ 2203.656676] RAX: ffffffffaf2a87f0 RBX: ffff888100360000 RCX:
ffffffffaf290191
[ 2203.656681] RDX: 0000000000098b5e RSI: 0000000000000004 RDI:
ffff88811a3c4f60
[ 2203.656686] RBP: 0000000000000000 R08: 0000000000000001 R09:
ffff88811a3c4f63
[ 2203.656690] R10: ffffed10234789ec R11: 0000000000000001 R12:
0000000000000003
[ 2203.656695] R13: ffff888100360000 R14: 0000000000000000 R15:
0000000000000000
[ 2203.656729] default_idle_call+0x5a/0x150
[ 2203.656735] cpuidle_idle_call+0x1c6/0x220
[ 2203.656780] do_idle+0xab/0x100
[ 2203.656786] cpu_startup_entry+0x19/0x20
[ 2203.656793] secondary_startup_64_no_verify+0xc2/0xcb
[ 2203.657409] The buggy address belongs to the page:
[ 2203.658648] page:0000000027a9842f refcount:1 mapcount:0
mapping:0000000000000000 index:0x0 pfn:0x11a388
[ 2203.658665] flags:
0x17ffffc0001000(reserved|node=0|zone=2|lastcpupid=0x1fffff)
[ 2203.658675] raw: 0017ffffc0001000 ffffea000468e208 ffffea000468e208
0000000000000000
[ 2203.658682] raw: 0000000000000000 0000000000000000 00000001ffffffff
0000000000000000
[ 2203.658686] page dumped because: kasan: bad access detected
To reproduce(ipvlan with IPVLAN_MODE_L3):
Env setting:
=======================================================
modprobe ipvlan ipvlan_default_mode=1
sysctl net.ipv4.conf.eth0.forwarding=1
iptables -t nat -A POSTROUTING -s 20.0.0.0/255.255.255.0 -o eth0 -j
MASQUERADE
ip link add gw link eth0 type ipvlan
ip -4 addr add 20.0.0.254/24 dev gw
ip netns add net1
ip link add ipv1 link eth0 type ipvlan
ip link set ipv1 netns net1
ip netns exec net1 ip link set ipv1 up
ip netns exec net1 ip -4 addr add 20.0.0.4/24 dev ipv1
ip netns exec net1 route add default gw 20.0.0.254
ip netns exec net1 tc qdisc add dev ipv1 root netem loss 10%
ifconfig gw up
iptables -t filter -A OUTPUT -p tcp --dport 8888 -j REJECT --reject-with
icmp-port-unreachable
=======================================================
And then excute the shell(curl any address of eth0 can reach):
for((i=1;i<=100000;i++))
do
ip netns exec net1 curl x.x.x.x:8888
done
=======================================================
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: "t.feng" <fengtao40@huawei.com>
Suggested-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clearing the PBA bit from the driver is race prone and it may lead to
dropped interrupt events. This could potentially lead to the traffic
being completely halted.
Fixes: 5e8c5adf95f8 ("gve: DQO: Add core netdev features")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before blamed commit, pskb_may_pull() was used instead
of skb_header_pointer() in __vlan_get_protocol() and friends.
Few callers depended on skb->head being populated with MAC header,
syzbot caught one of them (skb_mac_gso_segment())
Add vlan_get_protocol_and_depth() to make the intent clearer
and use it where sensible.
This is a more generic fix than commit e9d3f80935b6
("net/af_packet: make sure to pull mac header") which was
dealing with a similar issue.
kernel BUG at include/linux/skbuff.h:2655 !
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 1441 Comm: syz-executor199 Not tainted 6.1.24-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
RIP: 0010:__skb_pull include/linux/skbuff.h:2655 [inline]
RIP: 0010:skb_mac_gso_segment+0x68f/0x6a0 net/core/gro.c:136
Code: fd 48 8b 5c 24 10 44 89 6b 70 48 c7 c7 c0 ae 0d 86 44 89 e6 e8 a1 91 d0 00 48 c7 c7 00 af 0d 86 48 89 de 31 d2 e8 d1 4a e9 ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
RSP: 0018:ffffc90001bd7520 EFLAGS: 00010286
RAX: ffffffff8469736a RBX: ffff88810f31dac0 RCX: ffff888115a18b00
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffc90001bd75e8 R08: ffffffff84697183 R09: fffff5200037adf9
R10: 0000000000000000 R11: dffffc0000000001 R12: 0000000000000012
R13: 000000000000fee5 R14: 0000000000005865 R15: 000000000000fed7
FS: 000055555633f300(0000) GS:ffff8881f6a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 0000000116fea000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
[<ffffffff847018dd>] __skb_gso_segment+0x32d/0x4c0 net/core/dev.c:3419
[<ffffffff8470398a>] skb_gso_segment include/linux/netdevice.h:4819 [inline]
[<ffffffff8470398a>] validate_xmit_skb+0x3aa/0xee0 net/core/dev.c:3725
[<ffffffff84707042>] __dev_queue_xmit+0x1332/0x3300 net/core/dev.c:4313
[<ffffffff851a9ec7>] dev_queue_xmit+0x17/0x20 include/linux/netdevice.h:3029
[<ffffffff851b4a82>] packet_snd net/packet/af_packet.c:3111 [inline]
[<ffffffff851b4a82>] packet_sendmsg+0x49d2/0x6470 net/packet/af_packet.c:3142
[<ffffffff84669a12>] sock_sendmsg_nosec net/socket.c:716 [inline]
[<ffffffff84669a12>] sock_sendmsg net/socket.c:736 [inline]
[<ffffffff84669a12>] __sys_sendto+0x472/0x5f0 net/socket.c:2139
[<ffffffff84669c75>] __do_sys_sendto net/socket.c:2151 [inline]
[<ffffffff84669c75>] __se_sys_sendto net/socket.c:2147 [inline]
[<ffffffff84669c75>] __x64_sys_sendto+0xe5/0x100 net/socket.c:2147
[<ffffffff8551d40f>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff8551d40f>] do_syscall_64+0x2f/0x50 arch/x86/entry/common.c:80
[<ffffffff85600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 469aceddfa3e ("vlan: consolidate VLAN parsing code and limit max parsing depth")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
