| Age | Commit message (Collapse) | Author |
|---|
|
Wire up RTL8723DS chipset support using the rtw88 SDIO HCI code as well
as the existing RTL8723D chipset code.
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-5-martin.blumenstingl@googlemail.com
|
|
The efuse of the SDIO RTL8723DS chip has only one known member: the mac
address is at offset 0x11a. Add a struct rtw8723ds_efuse describing this
and use it for copying the mac address when the SDIO bus is used.
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-3-martin.blumenstingl@googlemail.com
|
|
rtw_sdio_rx_isr() is responsible for receiving data from the wifi chip
and is called from the SDIO interrupt handler when the interrupt status
register (HISR) has the RX_REQUEST bit set. After the first batch of
data has been processed by the driver the wifi chip may have more data
ready to be read, which is managed by a loop in rtw_sdio_rx_isr().
It turns out that there are cases where the RX buffer length (from the
REG_SDIO_RX0_REQ_LEN register) does not match the data we receive. The
following two cases were observed with a RTL8723DS card:
- RX length is smaller than the total packet length including overhead
and actual data bytes (whose length is part of the buffer we read from
the wifi chip and is stored in rtw_rx_pkt_stat.pkt_len). This can
result in errors like:
skbuff: skb_over_panic: text:ffff8000011924ac len:3341 put:3341
(one case observed was: RX buffer length = 1536 bytes but
rtw_rx_pkt_stat.pkt_len = 1546 bytes, this is not valid as it means
we need to read beyond the end of the buffer)
- RX length looks valid but rtw_rx_pkt_stat.pkt_len is zero
Check if the RX_REQUEST is set in the HISR register for each iteration
inside rtw_sdio_rx_isr(). This mimics what the RTL8723DS vendor driver
does and makes the driver only read more data if the RX_REQUEST bit is
set (which seems to be a way for the card's hardware or firmware to
tell the host that data is ready to be processed).
For RTW_WCPU_11AC chips this check is not needed. The RTL8822BS vendor
driver for example states that this check is unnecessary (but still uses
it) and the RTL8822CS drops this check entirely.
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-2-martin.blumenstingl@googlemail.com
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522105049.1467313-44-schnelle@linux.ibm.com
|
|
Use bitmap_weight_and() instead of hand writing it.
This saves a few LoC and is slightly faster, should it mater.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/a29c2348a062408bec45cee2601b2417310e5ea7.1684865809.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add two helper functions for calling PCS methods. phylink_pcs_config()
allows us to handle PCS configuration specifics in one location, rather
than the two call sites. phylink_pcs_link_up() gives us consistency.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q1TzK-007Exd-Rs@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Holding the struct phy_device (phydev) lock is unnecessary when
accessing phydev->interface in the PHY driver .config_init method,
which is the only place that vsc85xx_rgmii_set_skews() is called from.
The phy_modify_paged() function implements required MDIO bus level
locking, which can not be achieved by a phydev lock.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VSC8501 PHY can use the same driver implementation as the VSC8502.
Adding the PHY ID and copying the handler functions of VSC8502 is
sufficient to operate it.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function accidentally dereferences "cpus" instead of returning
directly.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202305200354.KV3jU94w-lkp@intel.com/
Fixes: b48a0f72bc3e ("net/mlx5: Refactor completion irq request/release code")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add missing mutex init/destroy as caught by the lock's debug warning:
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
Fixes: da5d0027d666 ("net/mlx5: DR, Add cache for modify header pattern")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As priv->dfs_root is cleared, and therefore missed, when change
eswitch mode, move the creation of the root debugfs to the init
callback of mlx5e_nic_profile and mlx5e_uplink_rep_profile, and
the destruction to the cleanup callback for symmeter.
Fixes: 288eca60cc31 ("net/mlx5e: Add Ethernet driver debugfs")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As part of switchdev mode disablement, driver changes port netdevice
profile from uplink to nic. If this process is triggered by health
recovery flow (PCI reset, for ex.) profile attach would fail because all
fw commands aborted when internal error flag is set. As a result, nic
netdevice profile is not attached and driver fails to rollback to uplink
profile, which leave driver in broken state and cause crash later.
To handle broken state do netdevice profile initialization only instead
of full attachment and release mdev resources on driver suspend as
expected. Actual netdevice attachment is done during driver load.
Fixes: c4d7eb57687f ("net/mxl5e: Add change profile method")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Caller of mlx5e_tc_act_post_parse() needs it to parse only the subset of
actions starting after previous split and ending at the current action.
However, that range is not provided as arguments and
mlx5e_tc_act_post_parse() uses generic flow_action_for_each() that iterates
over all flow actions. Not only this is redundant, it also causes a bug
when mlx5e_tc_act->post_parse() callback is not idempotent since it will be
called for every split. For example, ct action tc_act_post_parse_ct()
callback obtains a reference to mlx5_ct_ft instance and calling it several
times during parsing stage will cause reference counter imbalance.
Fix the issue by providing a proper action range of the current split
subset to mlx5e_tc_act_post_parse() and only calling
mlx5e_tc_act->post_parse() for actions inside the subset range.
Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Don't query the firmware so many times (num rqs * num wqes * wqe frags)
because it slows down linearly the interface creation time when the
product is larger. Do it only once per mdev and store the result in
mlx5e_param.
Due to helper function being called from different files, move it to
an appropriate location. Rename the function with a proper prefix and
add a small cleanup.
This fix applies only for legacy rq.
Fixes: 1b1e4868836a ("net/mlx5e: Use query_special_contexts for mkeys")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5 driver needs to parse traces with event_id inside the range of
first_string_trace and num_string_trace. However, mlx5 is parsing all
events with event_id >= first_string_trace.
Fix it by checking for the correct range.
Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There is no point in recovery during device removal. Also, if health
work started need to wait for it to avoid races and NULL pointer
access.
Hence, drain health WQ before removing device.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5 health mechanism is using devlink APIs, which are using devlink
notify APIs. After the cited patch, using devlink notify APIs after
devlink is unregistered triggers a WARN_ON().
Hence, drain health WQ before devlink is unregistered.
Fixes: cf530217408e ("devlink: Notify users when objects are accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The shared buffer pools configuration which are stored in the SBCM
register are updated when the user changes the prio2buffer mapping.
However, in case the user desired prio2buffer change is invalid,
which can occur due to mapping a lossless priority to a not large enough
buffer, the SBCM update should not be performed, as the user command is
failed.
Thus, Perform the SBCM update only after xoff threshold calculation is
performed and the user prio2buffer mapping is validated.
Fixes: a440030d8946 ("net/mlx5e: Update shared buffer along with device buffer changes")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, when a user triggers a change in port buffer headroom
(buffers 0-7), the driver checks that the requested headroom does
not exceed the total port buffer size. However, this check does not
take into account the internal buffers (buffers 8-9), which are also
part of the total port buffer. This can result in treating invalid port
buffer change requests as valid, causing unintended changes to the shared
buffer.
To address this, include the internal buffers size in the calculation of
available port buffer space which ensures that port buffer requests do not
exceed the correct limit.
Furthermore, remove internal buffers (8-9) size from the total_size
calculation as these buffers are reserved for internal use and are not
exposed to the user.
While at it, add verbosity to the debug prints in
mlx5e_port_query_buffer() function to ease future debugging.
Fixes: ecdf2dadee8e ("net/mlx5e: Receive buffer support for DCBX")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit adds a compeletion to remove dependency on rtnl
lock. But it causes a deadlock for multiple encapsulations:
crash> bt ffff8aece8a64000
PID: 1514557 TASK: ffff8aece8a64000 CPU: 3 COMMAND: "tc"
#0 [ffffa6d14183f368] __schedule at ffffffffb8ba7f45
#1 [ffffa6d14183f3f8] schedule at ffffffffb8ba8418
#2 [ffffa6d14183f418] schedule_preempt_disabled at ffffffffb8ba8898
#3 [ffffa6d14183f428] __mutex_lock at ffffffffb8baa7f8
#4 [ffffa6d14183f4d0] mutex_lock_nested at ffffffffb8baabeb
#5 [ffffa6d14183f4e0] mlx5e_attach_encap at ffffffffc0f48c17 [mlx5_core]
#6 [ffffa6d14183f628] mlx5e_tc_add_fdb_flow at ffffffffc0f39680 [mlx5_core]
#7 [ffffa6d14183f688] __mlx5e_add_fdb_flow at ffffffffc0f3b636 [mlx5_core]
#8 [ffffa6d14183f6f0] mlx5e_tc_add_flow at ffffffffc0f3bcdf [mlx5_core]
#9 [ffffa6d14183f728] mlx5e_configure_flower at ffffffffc0f3c1d1 [mlx5_core]
#10 [ffffa6d14183f790] mlx5e_rep_setup_tc_cls_flower at ffffffffc0f3d529 [mlx5_core]
#11 [ffffa6d14183f7a0] mlx5e_rep_setup_tc_cb at ffffffffc0f3d714 [mlx5_core]
#12 [ffffa6d14183f7b0] tc_setup_cb_add at ffffffffb8931bb8
#13 [ffffa6d14183f810] fl_hw_replace_filter at ffffffffc0dae901 [cls_flower]
#14 [ffffa6d14183f8d8] fl_change at ffffffffc0db5c57 [cls_flower]
#15 [ffffa6d14183f970] tc_new_tfilter at ffffffffb8936047
#16 [ffffa6d14183fac8] rtnetlink_rcv_msg at ffffffffb88c7c31
#17 [ffffa6d14183fb50] netlink_rcv_skb at ffffffffb8942853
#18 [ffffa6d14183fbc0] rtnetlink_rcv at ffffffffb88c1835
#19 [ffffa6d14183fbd0] netlink_unicast at ffffffffb8941f27
#20 [ffffa6d14183fc18] netlink_sendmsg at ffffffffb8942245
#21 [ffffa6d14183fc98] sock_sendmsg at ffffffffb887d482
#22 [ffffa6d14183fcb8] ____sys_sendmsg at ffffffffb887d81a
#23 [ffffa6d14183fd38] ___sys_sendmsg at ffffffffb88806e2
#24 [ffffa6d14183fe90] __sys_sendmsg at ffffffffb88807a2
#25 [ffffa6d14183ff28] __x64_sys_sendmsg at ffffffffb888080f
#26 [ffffa6d14183ff38] do_syscall_64 at ffffffffb8b9b6a8
#27 [ffffa6d14183ff50] entry_SYSCALL_64_after_hwframe at ffffffffb8c0007c
crash> bt 0xffff8aeb07544000
PID: 1110766 TASK: ffff8aeb07544000 CPU: 0 COMMAND: "kworker/u20:9"
#0 [ffffa6d14e6b7bd8] __schedule at ffffffffb8ba7f45
#1 [ffffa6d14e6b7c68] schedule at ffffffffb8ba8418
#2 [ffffa6d14e6b7c88] schedule_timeout at ffffffffb8baef88
#3 [ffffa6d14e6b7d10] wait_for_completion at ffffffffb8ba968b
#4 [ffffa6d14e6b7d60] mlx5e_take_all_encap_flows at ffffffffc0f47ec4 [mlx5_core]
#5 [ffffa6d14e6b7da0] mlx5e_rep_update_flows at ffffffffc0f3e734 [mlx5_core]
#6 [ffffa6d14e6b7df8] mlx5e_rep_neigh_update at ffffffffc0f400bb [mlx5_core]
#7 [ffffa6d14e6b7e50] process_one_work at ffffffffb80acc9c
#8 [ffffa6d14e6b7ed0] worker_thread at ffffffffb80ad012
#9 [ffffa6d14e6b7f10] kthread at ffffffffb80b615d
#10 [ffffa6d14e6b7f50] ret_from_fork at ffffffffb8001b2f
After the first encap is attached, flow will be added to encap
entry's flows list. If neigh update is running at this time, the
following encaps of the flow can't hold the encap_tbl_lock and
sleep. If neigh update thread is waiting for that flow's init_done,
deadlock happens.
Fix it by holding lock outside of the for loop. If neigh update is
running, prevent encap flows from offloading. Since the lock is held
outside of the for loop, concurrent creation of encap entries is not
allowed. So remove unnecessary wait_for_completion call for res_ready.
Fixes: 95435ad7999b ("net/mlx5e: Only access fully initialized flows in neigh update")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Move set_encap_dests() and clean_encap_dests() to the tunnel encap
dedicated file. And rename them to mlx5e_tc_tun_encap_dests_set()
and mlx5e_tc_tun_encap_dests_unset().
No functional change in this patch. It is needed in the next patch.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Avoid reading the STAT1 registers more than once while getting the PCS
state, as this register contains latching-low bits that are lost after
the first read.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_resolve_c73() to resolve the clause 73 autonegotiation
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xpcs was indicating symmetric pause should be enabled regardless of
the advertisements by either party. Fix this to use
linkmode_resolve_pause() now that we're no longer obliterating the
link partner's advertisement by logically anding it with our own.
This is transitional, the function will be entirely replaced with
phylink_resolve_c73() in the following patch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
lp_advertising is supposed to reflect the link partner's advertisement
unmodified by the local advertisement, but xpcs bitwise ands it with
the local advertisement prior to calculating the resolution of the
negotiation.
Fix this by moving the bitwise and to xpcs_resolve_lpa_c73() so it can
place the results in a temporary bitmap before passing that to
ixpcs_get_max_usxgmii_speed().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert xpcs clause 73 reading to use the newly introduced
mii_c73_to_linkmode() helper to translate the link partner
advertisement to an ethtool bitmap.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Read the clause 73 link partner advertisement in a loop and then
translate to the ethtool modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a function to resolve clause 73 negotiation according to the
priority resolution function described in clause 73.3.6.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Phylink had two chunks of code virtually the same for resolving the
negotiated pause modes. Factor this down to one function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Historically there was a reason why port_dev() along with for example
port_split() did get port_index instead of the devlink_port pointer.
With the locking changes that were done which ensured devlink instance
mutex is hold for every command, the port ops could get devlink_port
pointer directly. Change the forgotten port_dev() op to be as others
and pass devlink_port pointer instead of port_index.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The notification about created port is send from devl_port_register()
function called from ops->port_new(). No need to send it again here,
so remove the call and the helper function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2023-05-22
This series provides bug fixes for the mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When taking a network interface down (or removing a SFP module) after
the PHY has encountered an error, phy_stop() complains incorrectly
that it was called from HALTED state.
The reason this is incorrect is that the network driver will have
called phy_start() when the interface was brought up, and the fact
that the PHY has a problem bears no relationship to the administrative
state of the interface. Taking the interface administratively down
(which calls phy_stop()) is always the right thing to do after a
successful phy_start() call, whether or not the PHY has encountered
an error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit c6d96df9fa2c ("net: ethernet: mtk_eth_soc: drop generic vlan rx
offload, only use DSA untagging") makes VLAN RX offloading to be only used
on the SoCs without the MTK_NETSYS_V2 ability (which are not just MT7621
and MT7622). The commit disables the proper handling of special tagged
(DSA) frames, added with commit 87e3df4961f4 ("net-next: ethernet:
mediatek: add CDM able to recognize the tag for DSA"), for non
MTK_NETSYS_V2 SoCs when it finds a MAC that does not use DSA. So if the
other MAC uses DSA, the CDMQ component transmits DSA tagged frames to the
CPU improperly. This issue can be observed on frames with TCP, for example,
a TCP speed test using iperf3 won't work.
The commit disables the proper handling of special tagged (DSA) frames
because it assumes that these SoCs don't use more than one MAC, which is
wrong. Although I made Frank address this false assumption on the patch log
when they sent the patch on behalf of Felix, the code still made changes
with this assumption.
Therefore, the proper handling of special tagged (DSA) frames must be kept
enabled in all circumstances as it doesn't affect non DSA tagged frames.
Hardware DSA untagging, introduced with the commit 2d7605a72906 ("net:
ethernet: mtk_eth_soc: enable hardware DSA untagging"), and VLAN RX
offloading are operations on the two CDM components of the frame engine,
CDMP and CDMQ, which connect to Packet DMA (PDMA) and QoS DMA (QDMA) and
are between the MACs and the CPU. These operations apply to all MACs of the
SoC so if one MAC uses DSA and the other doesn't, the hardware DSA
untagging operation will cause the CDMP component to transmit non DSA
tagged frames to the CPU improperly.
Since the VLAN RX offloading feature configuration was dropped, VLAN RX
offloading can only be used along with hardware DSA untagging. So, for the
case above, we need to disable both features and leave it to the CPU,
therefore software, to untag the DSA and VLAN tags.
So the correct way to handle this is:
For all SoCs:
Enable the proper handling of special tagged (DSA) frames
(MTK_CDMQ_IG_CTRL).
For non MTK_NETSYS_V2 SoCs:
Enable hardware DSA untagging (MTK_CDMP_IG_CTRL).
Enable VLAN RX offloading (MTK_CDMP_EG_CTRL).
When a non MTK_NETSYS_V2 SoC MAC does not use DSA:
Disable hardware DSA untagging (MTK_CDMP_IG_CTRL).
Disable VLAN RX offloading (MTK_CDMP_EG_CTRL).
Fixes: c6d96df9fa2c ("net: ethernet: mtk_eth_soc: drop generic vlan rx offload, only use DSA untagging")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for using IPv6 Big TCP on DQ which can handle large TSO/GRO
packets. See https://lwn.net/Articles/895398/. This can improve the
throughput and CPU usage.
Perf test result:
ip -d link show $DEV
gso_max_size 185000 gso_max_segs 65535 tso_max_size 262143 tso_max_segs 65535 gro_max_size 185000
For performance, tested with neper using 9k MTU on hardware that supports 200Gb/s line rate.
In single streams when line rate is not saturated, we expect throughput improvements.
When the networking is performing at line rate, we expect cpu usage improvements.
Tcp_stream (unidirectional stream test, T=thread, F=flow):
skb=180kb, T=1, F=1, no zerocopy: throughput average=64576.88 Mb/s, sender stime=8.3, receiver stime=10.68
skb=64kb, T=1, F=1, no zerocopy: throughput average=64862.54 Mb/s, sender stime=9.96, receiver stime=12.67
skb=180kb, T=1, F=1, yes zerocopy: throughput average=146604.97 Mb/s, sender stime=10.61, receiver stime=5.52
skb=64kb, T=1, F=1, yes zerocopy: throughput average=131357.78 Mb/s, sender stime=12.11, receiver stime=12.25
skb=180kb, T=20, F=100, no zerocopy: throughput average=182411.37 Mb/s, sender stime=41.62, receiver stime=79.4
skb=64kb, T=20, F=100, no zerocopy: throughput average=182892.02 Mb/s, sender stime=57.39, receiver stime=72.69
skb=180kb, T=20, F=100, yes zerocopy: throughput average=182337.65 Mb/s, sender stime=27.94, receiver stime=39.7
skb=64kb, T=20, F=100, yes zerocopy: throughput average=182144.20 Mb/s, sender stime=47.06, receiver stime=39.01
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522201552.3585421-1-ziweixiao@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver's interrupt service routine is requested with the
IRQF_NO_THREAD if MSI is available. This means that the routine is
invoked in hardirq context even on PREEMPT_RT. The routine itself is
relatively short and schedules a worker, performs register access and
schedules NAPI. On PREEMPT_RT, scheduling NAPI from hardirq results in
waking ksoftirqd for further processing so using NAPI threads with this
driver is highly recommended since it NULL routes the threaded-IRQ
efforts.
Adding rtl_hw_aspm_clkreq_enable() to the ISR is problematic on
PREEMPT_RT because the function uses spinlock_t locks which become
sleeping locks on PREEMPT_RT. The locks are only used to protect
register access and don't nest into other functions or locks. They are
also not used for unbounded period of time. Therefore it looks okay to
convert them to raw_spinlock_t.
Convert the three locks which are used from the interrupt service
routine to raw_spinlock_t.
Fixes: e1ed3e4d9111 ("r8169: disable ASPM during NAPI poll")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20230522134121.uxjax0F5@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add layer 4 RSS hashing on UDP traffic to allow for the
utilization of multiple queues for multiple connections on
the same IP address.
Previously, since the introduction of the driver, RSS hashing
was only performed on the source and destination IP addresses
of UDP packets thereby limiting UDP traffic to a single queue
for multiple connections on the same IP address. The transport
layer is now included in RSS hashing for UDP traffic, which
was not previously the case. The reason behind the previous
limitation is unclear - either a historic limitation of the
NFP device, or an oversight.
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20230522141335.22536-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Walsun offers commercial ("C") and industrial ("I") variants of
multi-rate copper SFP+ modules.
Add quirk for HXSX-ATRI-1 using same parameters as the already supported
commercial variant HXSX-ATRC-1.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230522145242.30192-2-josua@solid-run.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Page pool for each rx queue enhance rx side performance
by reclaiming buffers back to each queue specific pool. DMA
mapping is done only for first allocation of buffers.
As subsequent buffers allocation avoid DMA mapping,
it results in performance improvement.
Image | Performance
------------ | ------------
Vannila | 3Mpps
|
with this | 42Mpps
change |
---------------------------
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://lore.kernel.org/r/20230522020404.152020-1-rkannoth@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After the cited patch, mlx5_irq xarray index can be different then
mlx5_irq MSIX table index.
Fix it by storing both mlx5_irq xarray index and MSIX table index.
Fixes: 3354822cde5a ("net/mlx5: Use dynamic msix vectors allocation")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited patch deny the user of changing the affinity of mlx5 irqs,
which break backward compatibility.
Hence, allow the user to change the affinity of mlx5 irqs.
Fixes: bbac70c74183 ("net/mlx5: Use newer affinity descriptor")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Whenever a shutdown is invoked, free irqs only and keep mlx5_irq
synthetic wrapper intact in order to avoid use-after-free on
system shutdown.
for example:
==================================================================
BUG: KASAN: use-after-free in _find_first_bit+0x66/0x80
Read of size 8 at addr ffff88823fc0d318 by task kworker/u192:0/13608
CPU: 25 PID: 13608 Comm: kworker/u192:0 Tainted: G B W O 6.1.21-cloudflare-kasan-2023.3.21 #1
Hardware name: GIGABYTE R162-R2-GEN0/MZ12-HD2-CD, BIOS R14 05/03/2021
Workqueue: mlx5e mlx5e_tx_timeout_work [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x48
print_report+0x170/0x473
? _find_first_bit+0x66/0x80
kasan_report+0xad/0x130
? _find_first_bit+0x66/0x80
_find_first_bit+0x66/0x80
mlx5e_open_channels+0x3c5/0x3a10 [mlx5_core]
? console_unlock+0x2fa/0x430
? _raw_spin_lock_irqsave+0x8d/0xf0
? _raw_spin_unlock_irqrestore+0x42/0x80
? preempt_count_add+0x7d/0x150
? __wake_up_klogd.part.0+0x7d/0xc0
? vprintk_emit+0xfe/0x2c0
? mlx5e_trigger_napi_sched+0x40/0x40 [mlx5_core]
? dev_attr_show.cold+0x35/0x35
? devlink_health_do_dump.part.0+0x174/0x340
? devlink_health_report+0x504/0x810
? mlx5e_reporter_tx_timeout+0x29d/0x3a0 [mlx5_core]
? mlx5e_tx_timeout_work+0x17c/0x230 [mlx5_core]
? process_one_work+0x680/0x1050
mlx5e_safe_switch_params+0x156/0x220 [mlx5_core]
? mlx5e_switch_priv_channels+0x310/0x310 [mlx5_core]
? mlx5_eq_poll_irq_disabled+0xb6/0x100 [mlx5_core]
mlx5e_tx_reporter_timeout_recover+0x123/0x240 [mlx5_core]
? __mutex_unlock_slowpath.constprop.0+0x2b0/0x2b0
devlink_health_reporter_recover+0xa6/0x1f0
devlink_health_report+0x2f7/0x810
? vsnprintf+0x854/0x15e0
mlx5e_reporter_tx_timeout+0x29d/0x3a0 [mlx5_core]
? mlx5e_reporter_tx_err_cqe+0x1a0/0x1a0 [mlx5_core]
? mlx5e_tx_reporter_timeout_dump+0x50/0x50 [mlx5_core]
? mlx5e_tx_reporter_dump_sq+0x260/0x260 [mlx5_core]
? newidle_balance+0x9b7/0xe30
? psi_group_change+0x6a7/0xb80
? mutex_lock+0x96/0xf0
? __mutex_lock_slowpath+0x10/0x10
mlx5e_tx_timeout_work+0x17c/0x230 [mlx5_core]
process_one_work+0x680/0x1050
worker_thread+0x5a0/0xeb0
? process_one_work+0x1050/0x1050
kthread+0x2a2/0x340
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Freed by task 1:
kasan_save_stack+0x23/0x50
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x169/0x1d0
slab_free_freelist_hook+0xd2/0x190
__kmem_cache_free+0x1a1/0x2f0
irq_pool_free+0x138/0x200 [mlx5_core]
mlx5_irq_table_destroy+0xf6/0x170 [mlx5_core]
mlx5_core_eq_free_irqs+0x74/0xf0 [mlx5_core]
shutdown+0x194/0x1aa [mlx5_core]
pci_device_shutdown+0x75/0x120
device_shutdown+0x35c/0x620
kernel_restart+0x60/0xa0
__do_sys_reboot+0x1cb/0x2c0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x4b/0xb5
The buggy address belongs to the object at ffff88823fc0d300
which belongs to the cache kmalloc-192 of size 192
The buggy address is located 24 bytes inside of
192-byte region [ffff88823fc0d300, ffff88823fc0d3c0)
The buggy address belongs to the physical page:
page:0000000010139587 refcount:1 mapcount:0 mapping:0000000000000000
index:0x0 pfn:0x23fc0c
head:0000000010139587 order:1 compound_mapcount:0 compound_pincount:0
flags: 0x2ffff800010200(slab|head|node=0|zone=2|lastcpupid=0x1ffff)
raw: 002ffff800010200 0000000000000000 dead000000000122 ffff88810004ca00
raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88823fc0d200: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88823fc0d280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff88823fc0d300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88823fc0d380: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff88823fc0d400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
general protection fault, probably for non-canonical address
0xdffffc005c40d7ac: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: probably user-memory-access in range [0x00000002e206bd60-0x00000002e206bd67]
CPU: 25 PID: 13608 Comm: kworker/u192:0 Tainted: G B W O 6.1.21-cloudflare-kasan-2023.3.21 #1
Hardware name: GIGABYTE R162-R2-GEN0/MZ12-HD2-CD, BIOS R14 05/03/2021
Workqueue: mlx5e mlx5e_tx_timeout_work [mlx5_core]
RIP: 0010:__alloc_pages+0x141/0x5c0
Call Trace:
<TASK>
? sysvec_apic_timer_interrupt+0xa0/0xc0
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? __alloc_pages_slowpath.constprop.0+0x1ec0/0x1ec0
? _raw_spin_unlock_irqrestore+0x3d/0x80
__kmalloc_large_node+0x80/0x120
? kvmalloc_node+0x4e/0x170
__kmalloc_node+0xd4/0x150
kvmalloc_node+0x4e/0x170
mlx5e_open_channels+0x631/0x3a10 [mlx5_core]
? console_unlock+0x2fa/0x430
? _raw_spin_lock_irqsave+0x8d/0xf0
? _raw_spin_unlock_irqrestore+0x42/0x80
? preempt_count_add+0x7d/0x150
? __wake_up_klogd.part.0+0x7d/0xc0
? vprintk_emit+0xfe/0x2c0
? mlx5e_trigger_napi_sched+0x40/0x40 [mlx5_core]
? dev_attr_show.cold+0x35/0x35
? devlink_health_do_dump.part.0+0x174/0x340
? devlink_health_report+0x504/0x810
? mlx5e_reporter_tx_timeout+0x29d/0x3a0 [mlx5_core]
? mlx5e_tx_timeout_work+0x17c/0x230 [mlx5_core]
? process_one_work+0x680/0x1050
mlx5e_safe_switch_params+0x156/0x220 [mlx5_core]
? mlx5e_switch_priv_channels+0x310/0x310 [mlx5_core]
? mlx5_eq_poll_irq_disabled+0xb6/0x100 [mlx5_core]
mlx5e_tx_reporter_timeout_recover+0x123/0x240 [mlx5_core]
? __mutex_unlock_slowpath.constprop.0+0x2b0/0x2b0
devlink_health_reporter_recover+0xa6/0x1f0
devlink_health_report+0x2f7/0x810
? vsnprintf+0x854/0x15e0
mlx5e_reporter_tx_timeout+0x29d/0x3a0 [mlx5_core]
? mlx5e_reporter_tx_err_cqe+0x1a0/0x1a0 [mlx5_core]
? mlx5e_tx_reporter_timeout_dump+0x50/0x50 [mlx5_core]
? mlx5e_tx_reporter_dump_sq+0x260/0x260 [mlx5_core]
? newidle_balance+0x9b7/0xe30
? psi_group_change+0x6a7/0xb80
? mutex_lock+0x96/0xf0
? __mutex_lock_slowpath+0x10/0x10
mlx5e_tx_timeout_work+0x17c/0x230 [mlx5_core]
process_one_work+0x680/0x1050
worker_thread+0x5a0/0xeb0
? process_one_work+0x1050/0x1050
kthread+0x2a2/0x340
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
---[ end trace 0000000000000000 ]---
RIP: 0010:__alloc_pages+0x141/0x5c0
Code: e0 39 a3 96 89 e9 b8 22 01 32 01 83 e1 0f 48 89 fa 01 c9 48 c1 ea
03 d3 f8 83 e0 03 89 44 24 6c 48 b8 00 00 00 00 00 fc ff df <80> 3c 02
00 0f 85 fc 03 00 00 89 e8 4a 8b 14 f5 e0 39 a3 96 4c 89
RSP: 0018:ffff888251f0f438 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 1ffff1104a3e1e8b RCX: 0000000000000000
RDX: 000000005c40d7ac RSI: 0000000000000003 RDI: 00000002e206bd60
RBP: 0000000000052dc0 R08: ffff8882b0044218 R09: ffff8882b0045e8a
R10: fffffbfff300fefc R11: ffff888167af4000 R12: 0000000000000003
R13: 0000000000000000 R14: 00000000696c7070 R15: ffff8882373f4380
FS: 0000000000000000(0000) GS:ffff88bf2be80000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005641d031eee8 CR3: 0000002e7ca14000 CR4: 0000000000350ee0
Kernel panic - not syncing: Fatal exception
Kernel Offset: 0x11000000 from 0xffffffff81000000 (relocation range:
0xffffffff80000000-0xffffffffbfffffff)
---[ end Kernel panic - not syncing: Fatal exception ]---]
Reported-by: Frederick Lawler <fred@cloudflare.com>
Link: https://lore.kernel.org/netdev/be5b9271-7507-19c5-ded1-fa78f1980e69@cloudflare.com
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
Fixes: fadd59fc50d0 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
Fixes: fadd59fc50d0 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
devcom events are sent to all registered component. Following the
cited patch, it is possible for two components, e.g.: two eswitches,
to send devcom events, while both components are registered. This
means eswitch layer will do double un/pairing, which is double
allocation and free of resources, even though only one un/pairing is
needed. flow example:
cpu0 cpu1
---- ----
mlx5_devlink_eswitch_mode_set(dev0)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw0)
mlx5_devlink_eswitch_mode_set(dev1)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw1)
mlx5_devcom_send_event()
mlx5_devcom_send_event()
Hence, check whether the eswitches are already un/paired before
free/allocation of resources.
Fixes: 09b278462f16 ("net: devlink: enable parallel ops on netlink interface")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Cited patch is using the eswitch object mapping pool while
in nic mode where it isn't initialized. This results in the
trace below [0].
Fix that by using either nic or eswitch object mapping pool
depending if eswitch is enabled or not.
[0]:
[ 826.446057] ==================================================================
[ 826.446729] BUG: KASAN: slab-use-after-free in mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.447515] Read of size 8 at addr ffff888194485830 by task tc/6233
[ 826.448243] CPU: 16 PID: 6233 Comm: tc Tainted: G W 6.3.0-rc6+ #1
[ 826.448890] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 826.449785] Call Trace:
[ 826.450052] <TASK>
[ 826.450302] dump_stack_lvl+0x33/0x50
[ 826.450650] print_report+0xc2/0x610
[ 826.450998] ? __virt_addr_valid+0xb1/0x130
[ 826.451385] ? mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.451935] kasan_report+0xae/0xe0
[ 826.452276] ? mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.452829] mlx5_add_flow_rules+0x30/0x490 [mlx5_core]
[ 826.453368] ? __kmalloc_node+0x5a/0x120
[ 826.453733] esw_add_restore_rule+0x20f/0x270 [mlx5_core]
[ 826.454288] ? mlx5_eswitch_add_send_to_vport_meta_rule+0x260/0x260 [mlx5_core]
[ 826.455011] ? mutex_unlock+0x80/0xd0
[ 826.455361] ? __mutex_unlock_slowpath.constprop.0+0x210/0x210
[ 826.455862] ? mapping_add+0x2cb/0x440 [mlx5_core]
[ 826.456425] mlx5e_tc_action_miss_mapping_get+0x139/0x180 [mlx5_core]
[ 826.457058] ? mlx5e_tc_update_skb_nic+0xb0/0xb0 [mlx5_core]
[ 826.457636] ? __kasan_kmalloc+0x77/0x90
[ 826.458000] ? __kmalloc+0x57/0x120
[ 826.458336] mlx5_tc_ct_flow_offload+0x325/0xe40 [mlx5_core]
[ 826.458916] ? ct_kernel_enter.constprop.0+0x48/0xa0
[ 826.459360] ? mlx5_tc_ct_parse_action+0xf0/0xf0 [mlx5_core]
[ 826.459933] ? mlx5e_mod_hdr_attach+0x491/0x520 [mlx5_core]
[ 826.460507] ? mlx5e_mod_hdr_get+0x12/0x20 [mlx5_core]
[ 826.461046] ? mlx5e_tc_attach_mod_hdr+0x154/0x170 [mlx5_core]
[ 826.461635] mlx5e_configure_flower+0x969/0x2110 [mlx5_core]
[ 826.462217] ? _raw_spin_lock_bh+0x85/0xe0
[ 826.462597] ? __mlx5e_add_fdb_flow+0x750/0x750 [mlx5_core]
[ 826.463163] ? kasan_save_stack+0x2e/0x40
[ 826.463534] ? down_read+0x115/0x1b0
[ 826.463878] ? down_write_killable+0x110/0x110
[ 826.464288] ? tc_setup_action.part.0+0x9f/0x3b0
[ 826.464701] ? mlx5e_is_uplink_rep+0x4c/0x90 [mlx5_core]
[ 826.465253] ? mlx5e_tc_reoffload_flows_work+0x130/0x130 [mlx5_core]
[ 826.465878] tc_setup_cb_add+0x112/0x250
[ 826.466247] fl_hw_replace_filter+0x230/0x310 [cls_flower]
[ 826.466724] ? fl_hw_destroy_filter+0x1a0/0x1a0 [cls_flower]
[ 826.467212] fl_change+0x14e1/0x2030 [cls_flower]
[ 826.467636] ? sock_def_readable+0x89/0x120
[ 826.468019] ? fl_tmplt_create+0x2d0/0x2d0 [cls_flower]
[ 826.468509] ? kasan_unpoison+0x23/0x50
[ 826.468873] ? get_random_u16+0x180/0x180
[ 826.469244] ? __radix_tree_lookup+0x2b/0x130
[ 826.469640] ? fl_get+0x7b/0x140 [cls_flower]
[ 826.470042] ? fl_mask_put+0x200/0x200 [cls_flower]
[ 826.470478] ? __mutex_unlock_slowpath.constprop.0+0x210/0x210
[ 826.470973] ? fl_tmplt_create+0x2d0/0x2d0 [cls_flower]
[ 826.471427] tc_new_tfilter+0x644/0x1050
[ 826.471795] ? tc_get_tfilter+0x860/0x860
[ 826.472170] ? __thaw_task+0x130/0x130
[ 826.472525] ? arch_stack_walk+0x98/0xf0
[ 826.472892] ? cap_capable+0x9f/0xd0
[ 826.473235] ? security_capable+0x47/0x60
[ 826.473608] rtnetlink_rcv_msg+0x1d5/0x550
[ 826.473985] ? rtnl_calcit.isra.0+0x1f0/0x1f0
[ 826.474383] ? __stack_depot_save+0x35/0x4c0
[ 826.474779] ? kasan_save_stack+0x2e/0x40
[ 826.475149] ? kasan_save_stack+0x1e/0x40
[ 826.475518] ? __kasan_record_aux_stack+0x9f/0xb0
[ 826.475939] ? task_work_add+0x77/0x1c0
[ 826.476305] netlink_rcv_skb+0xe0/0x210
[ 826.476661] ? rtnl_calcit.isra.0+0x1f0/0x1f0
[ 826.477057] ? netlink_ack+0x7c0/0x7c0
[ 826.477412] ? rhashtable_jhash2+0xef/0x150
[ 826.477796] ? _copy_from_iter+0x105/0x770
[ 826.484386] netlink_unicast+0x346/0x490
[ 826.484755] ? netlink_attachskb+0x400/0x400
[ 826.485145] ? kernel_text_address+0xc2/0xd0
[ 826.485535] netlink_sendmsg+0x3b0/0x6c0
[ 826.485902] ? kernel_text_address+0xc2/0xd0
[ 826.486296] ? netlink_unicast+0x490/0x490
[ 826.486671] ? iovec_from_user.part.0+0x7a/0x1a0
[ 826.487083] ? netlink_unicast+0x490/0x490
[ 826.487461] sock_sendmsg+0x73/0xc0
[ 826.487803] ____sys_sendmsg+0x364/0x380
[ 826.488186] ? import_iovec+0x7/0x10
[ 826.488531] ? kernel_sendmsg+0x30/0x30
[ 826.488893] ? __copy_msghdr+0x180/0x180
[ 826.489258] ? kasan_save_stack+0x2e/0x40
[ 826.489629] ? kasan_save_stack+0x1e/0x40
[ 826.490002] ? __kasan_record_aux_stack+0x9f/0xb0
[ 826.490424] ? __call_rcu_common.constprop.0+0x46/0x580
[ 826.490876] ___sys_sendmsg+0xdf/0x140
[ 826.491231] ? copy_msghdr_from_user+0x110/0x110
[ 826.491649] ? fget_raw+0x120/0x120
[ 826.491988] ? ___sys_recvmsg+0xd9/0x130
[ 826.492355] ? folio_batch_add_and_move+0x80/0xa0
[ 826.492776] ? _raw_spin_lock+0x7a/0xd0
[ 826.493137] ? _raw_spin_lock+0x7a/0xd0
[ 826.493500] ? _raw_read_lock_irq+0x30/0x30
[ 826.493880] ? kasan_set_track+0x21/0x30
[ 826.494249] ? kasan_save_free_info+0x2a/0x40
[ 826.494650] ? do_sys_openat2+0xff/0x270
[ 826.495016] ? __fget_light+0x1b5/0x200
[ 826.495377] ? __virt_addr_valid+0xb1/0x130
[ 826.495763] __sys_sendmsg+0xb2/0x130
[ 826.496118] ? __sys_sendmsg_sock+0x20/0x20
[ 826.496501] ? __x64_sys_rseq+0x2e0/0x2e0
[ 826.496874] ? do_user_addr_fault+0x276/0x820
[ 826.497273] ? fpregs_assert_state_consistent+0x52/0x60
[ 826.497727] ? exit_to_user_mode_prepare+0x30/0x120
[ 826.498158] do_syscall_64+0x3d/0x90
[ 826.498502] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 826.498949] RIP: 0033:0x7f9b67f4f887
[ 826.499294] Code: 0a 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
[ 826.500742] RSP: 002b:00007fff5d1a5498 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[ 826.501395] RAX: ffffffffffffffda RBX: 0000000064413ce6 RCX: 00007f9b67f4f887
[ 826.501975] RDX: 0000000000000000 RSI: 00007fff5d1a5500 RDI: 0000000000000003
[ 826.502556] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000001
[ 826.503135] R10: 00007f9b67e08708 R11: 0000000000000246 R12: 0000000000000001
[ 826.503714] R13: 0000000000000001 R14: 00007fff5d1a9800 R15: 0000000000485400
[ 826.504304] </TASK>
[ 826.504753] Allocated by task 3764:
[ 826.505090] kasan_save_stack+0x1e/0x40
[ 826.505453] kasan_set_track+0x21/0x30
[ 826.505810] __kasan_kmalloc+0x77/0x90
[ 826.506164] __mlx5_create_flow_table+0x16d/0xbb0 [mlx5_core]
[ 826.506742] esw_offloads_enable+0x60d/0xfb0 [mlx5_core]
[ 826.507292] mlx5_eswitch_enable_locked+0x4d3/0x680 [mlx5_core]
[ 826.507885] mlx5_devlink_eswitch_mode_set+0x2a3/0x580 [mlx5_core]
[ 826.508513] devlink_nl_cmd_eswitch_set_doit+0xdf/0x1f0
[ 826.508969] genl_family_rcv_msg_doit.isra.0+0x146/0x1c0
[ 826.509427] genl_rcv_msg+0x28d/0x3e0
[ 826.509772] netlink_rcv_skb+0xe0/0x210
[ 826.510133] genl_rcv+0x24/0x40
[ 826.510448] netlink_unicast+0x346/0x490
[ 826.510810] netlink_sendmsg+0x3b0/0x6c0
[ 826.511179] sock_sendmsg+0x73/0xc0
[ 826.511519] __sys_sendto+0x18d/0x220
[ 826.511867] __x64_sys_sendto+0x72/0x80
[ 826.512232] do_syscall_64+0x3d/0x90
[ 826.512576] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 826.513220] Freed by task 5674:
[ 826.513535] kasan_save_stack+0x1e/0x40
[ 826.513893] kasan_set_track+0x21/0x30
[ 826.514245] kasan_save_free_info+0x2a/0x40
[ 826.514629] ____kasan_slab_free+0x11a/0x1b0
[ 826.515021] __kmem_cache_free+0x14d/0x280
[ 826.515399] tree_put_node+0x109/0x1c0 [mlx5_core]
[ 826.515907] mlx5_destroy_flow_table+0x119/0x630 [mlx5_core]
[ 826.516481] esw_offloads_steering_cleanup+0xe7/0x150 [mlx5_core]
[ 826.517084] esw_offloads_disable+0xe0/0x160 [mlx5_core]
[ 826.517632] mlx5_eswitch_disable_locked+0x26c/0x290 [mlx5_core]
[ 826.518225] mlx5_devlink_eswitch_mode_set+0x128/0x580 [mlx5_core]
[ 826.518834] devlink_nl_cmd_eswitch_set_doit+0xdf/0x1f0
[ 826.519286] genl_family_rcv_msg_doit.isra.0+0x146/0x1c0
[ 826.519748] genl_rcv_msg+0x28d/0x3e0
[ 826.520101] netlink_rcv_skb+0xe0/0x210
[ 826.520458] genl_rcv+0x24/0x40
[ 826.520771] netlink_unicast+0x346/0x490
[ 826.521137] netlink_sendmsg+0x3b0/0x6c0
[ 826.521505] sock_sendmsg+0x73/0xc0
[ 826.521842] __sys_sendto+0x18d/0x220
[ 826.522191] __x64_sys_sendto+0x72/0x80
[ 826.522554] do_syscall_64+0x3d/0x90
[ 826.522894] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 826.523540] Last potentially related work creation:
[ 826.523969] kasan_save_stack+0x1e/0x40
[ 826.524331] __kasan_record_aux_stack+0x9f/0xb0
[ 826.524739] insert_work+0x30/0x130
[ 826.525078] __queue_work+0x34b/0x690
[ 826.525426] queue_work_on+0x48/0x50
[ 826.525766] __rhashtable_remove_fast_one+0x4af/0x4d0 [mlx5_core]
[ 826.526365] del_sw_flow_group+0x1b5/0x270 [mlx5_core]
[ 826.526898] tree_put_node+0x109/0x1c0 [mlx5_core]
[ 826.527407] esw_offloads_steering_cleanup+0xd3/0x150 [mlx5_core]
[ 826.528009] esw_offloads_disable+0xe0/0x160 [mlx5_core]
[ 826.528616] mlx5_eswitch_disable_locked+0x26c/0x290 [mlx5_core]
[ 826.529218] mlx5_devlink_eswitch_mode_set+0x128/0x580 [mlx5_core]
[ 826.529823] devlink_nl_cmd_eswitch_set_doit+0xdf/0x1f0
[ 826.530276] genl_family_rcv_msg_doit.isra.0+0x146/0x1c0
[ 826.530733] genl_rcv_msg+0x28d/0x3e0
[ 826.531079] netlink_rcv_skb+0xe0/0x210
[ 826.531439] genl_rcv+0x24/0x40
[ 826.531755] netlink_unicast+0x346/0x490
[ 826.532123] netlink_sendmsg+0x3b0/0x6c0
[ 826.532487] sock_sendmsg+0x73/0xc0
[ 826.532825] __sys_sendto+0x18d/0x220
[ 826.533175] __x64_sys_sendto+0x72/0x80
[ 826.533533] do_syscall_64+0x3d/0x90
[ 826.533877] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 826.534521] The buggy address belongs to the object at ffff888194485800
which belongs to the cache kmalloc-512 of size 512
[ 826.535506] The buggy address is located 48 bytes inside of
freed 512-byte region [ffff888194485800, ffff888194485a00)
[ 826.536666] The buggy address belongs to the physical page:
[ 826.537138] page:00000000d75841dd refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x194480
[ 826.537915] head:00000000d75841dd order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[ 826.538595] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 826.539089] raw: 0200000000010200 ffff888100042c80 ffffea0004523800 dead000000000002
[ 826.539755] raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000
[ 826.540417] page dumped because: kasan: bad access detected
[ 826.541095] Memory state around the buggy address:
[ 826.541519] ffff888194485700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 826.542149] ffff888194485780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 826.542773] >ffff888194485800: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 826.543400] ^
[ 826.543822] ffff888194485880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 826.544452] ffff888194485900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 826.545079] ==================================================================
Fixes: 6702782845a5 ("net/mlx5e: TC, Set CT miss to the specific ct action instance")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
