summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2023-08-02net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_indexChristoph Hellwig
enetc_phc_index is only used via symbol_get, which was only ever intended for very internal symbols like this one. Use EXPORT_SYMBOL_GPL for it so that symbol_get can enforce only being used on EXPORT_SYMBOL_GPL symbols. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
2023-08-02wifi: ath12k: change to use dynamic memory for channel list of scanWen Gong
Currently there are about 60 channels for 6 GHz, then the size of chan_list in struct scan_req_params which is 40 is not enough to fill all the channel list of 6 GHz. Use dynamic memory to save the channel list of scan. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230717033431.21983-1-quic_wgong@quicinc.com
2023-08-02wifi: ath12k: trigger station disconnect on hardware restartWen Gong
Currently after the hardware restart triggered from the driver, the station interface connection remains intact, since a disconnect trigger is not sent to userspace. This can lead to a problem in targets where the wifi mac sequence is added by the firmware. After the target restart, its wifi mac sequence number gets reset to zero. Hence AP to which our device is connected will receive frames with a wifi mac sequence number jump to the past, thereby resulting in the AP dropping all these frames, until the frame arrives with a wifi mac sequence number which AP was expecting. To avoid such frame drops, its better to trigger a station disconnect upon target hardware restart which can be done with API ieee80211_reconfig_disconnect exposed to mac80211. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230714092555.2018-1-quic_wgong@quicinc.com
2023-08-02wifi: ath12k: Use pdev_id rather than mac_id to get pdevBaochen Qiang
We are seeing kernel crash in below test scenario: 1. make DUT connect to an WPA3 encrypted 11ax AP in Ch44 HE80 2. use "wpa_cli -i <inf> disconnect" to disconnect 3. wait for DUT to automatically reconnect Kernel crashes while waiting, below shows the crash stack: [ 755.120868] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 755.120871] #PF: supervisor read access in kernel mode [ 755.120872] #PF: error_code(0x0000) - not-present page [ 755.120873] PGD 0 P4D 0 [ 755.120875] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 755.120876] CPU: 7 PID: 0 Comm: swapper/7 Kdump: loaded Not tainted 5.19.0-rc1+ #3 [ 755.120878] Hardware name: Intel(R) Client Systems NUC11PHi7/NUC11PHBi7, BIOS PHTGL579.0063.2021.0707.1057 07/07/2021 [ 755.120879] RIP: 0010:ath12k_dp_process_rx_err+0x2b6/0x14a0 [ath12k] [ 755.120890] Code: 01 c0 48 c1 e0 05 48 8b 9c 07 b8 b2 00 00 48 c7 c0 61 ff 0e c1 48 85 db 53 48 0f 44 c6 48 c7 c6 80 9d 0f c1 50 e8 1a 25 00 00 <4c> 8b 3b 4d 8b 76 14 41 59 41 5a 41 8b 87 78 43 01 00 4d 85 f6 89 [ 755.120891] RSP: 0018:ffff9a93402c8d10 EFLAGS: 00010282 [ 755.120892] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000303 [ 755.120893] RDX: 0000000000000000 RSI: ffffffff93b7cbe9 RDI: 00000000ffffffff [ 755.120894] RBP: ffff9a93402c8e50 R08: ffffffff93e65360 R09: ffffffff942e044d [ 755.120894] R10: 0000000000000000 R11: 0000000000000063 R12: ffff8dbec5420000 [ 755.120895] R13: ffff8dbec5420000 R14: ffff8dbdefe9a0a0 R15: ffff8dbec5420000 [ 755.120896] FS: 0000000000000000(0000) GS:ffff8dc2705c0000(0000) knlGS:0000000000000000 [ 755.120897] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 755.120898] CR2: 0000000000000000 CR3: 0000000107be4005 CR4: 0000000000770ee0 [ 755.120898] PKRU: 55555554 [ 755.120899] Call Trace: [ 755.120900] <IRQ> [ 755.120903] ? ath12k_pci_write32+0x2e/0x80 [ath12k] [ 755.120910] ath12k_dp_service_srng+0x214/0x2e0 [ath12k] [ 755.120917] ath12k_pci_ext_grp_napi_poll+0x26/0x80 [ath12k] [ 755.120923] __napi_poll+0x2b/0x1c0 [ 755.120925] net_rx_action+0x2a1/0x2f0 [ 755.120927] __do_softirq+0xfa/0x2e9 [ 755.120929] irq_exit_rcu+0xb9/0xd0 [ 755.120932] common_interrupt+0xc1/0xe0 [ 755.120934] </IRQ> [ 755.120934] <TASK> [ 755.120935] asm_common_interrupt+0x2c/0x40 [ 755.120936] RIP: 0010:cpuidle_enter_state+0xdd/0x3a0 [ 755.120938] Code: 00 31 ff e8 45 e2 74 ff 80 7d d7 00 74 16 9c 58 0f 1f 40 00 f6 c4 02 0f 85 a0 02 00 00 31 ff e8 69 79 7b ff fb 0f 1f 44 00 00 <45> 85 ff 0f 88 6d 01 00 00 49 63 d7 4c 2b 6d c8 48 8d 04 52 48 8d [ 755.120939] RSP: 0018:ffff9a934018be50 EFLAGS: 00000246 [ 755.120940] RAX: ffff8dc2705c0000 RBX: 0000000000000002 RCX: 000000000000001f [ 755.120941] RDX: 000000afd0b532d3 RSI: ffffffff93b7cbe9 RDI: ffffffff93b8b66e [ 755.120942] RBP: ffff9a934018be88 R08: 0000000000000002 R09: 0000000000030500 [ 755.120942] R10: ffff9a934018be18 R11: 0000000000000741 R12: ffffba933fdc0600 [ 755.120943] R13: 000000afd0b532d3 R14: ffffffff93fcbc60 R15: 0000000000000002 [ 755.120945] cpuidle_enter+0x2e/0x40 [ 755.120946] call_cpuidle+0x23/0x40 [ 755.120948] do_idle+0x1ff/0x260 [ 755.120950] cpu_startup_entry+0x1d/0x20 [ 755.120951] start_secondary+0x10d/0x130 [ 755.120953] secondary_startup_64_no_verify+0xd3/0xdb [ 755.120956] </TASK> [ 755.120956] Modules linked in: michael_mic rfcomm cmac algif_hash algif_skcipher af_alg bnep qrtr_mhi intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio kvm_intel qrtr snd_hda_codec_hdmi kvm irqbypass ath12k snd_hda_intel snd_seq_midi crct10dif_pclmul mhi ghash_clmulni_intel snd_intel_dspcfg snd_seq_midi_event aesni_intel qmi_helpers i915 snd_rawmidi crypto_simd snd_hda_codec cryptd cec intel_cstate snd_hda_core mac80211 rc_core nouveau snd_seq snd_hwdep btusb drm_buddy drm_ttm_helper nls_iso8859_1 snd_pcm ttm btrtl snd_seq_device wmi_bmof mxm_wmi input_leds cfg80211 joydev btbcm drm_display_helper snd_timer btintel mei_me libarc4 drm_kms_helper bluetooth i2c_algo_bit snd fb_sys_fops syscopyarea mei sysfillrect ecdh_generic soundcore sysimgblt ecc acpi_pad mac_hid sch_fq_codel ipmi_devintf ipmi_msghandler msr parport_pc ppdev lp ramoops parport reed_solomon drm efi_pstore ip_tables x_tables autofs4 [ 755.120992] hid_generic usbhid hid ax88179_178a usbnet mii nvme nvme_core rtsx_pci_sdmmc crc32_pclmul i2c_i801 intel_lpss_pci i2c_smbus intel_lpss rtsx_pci idma64 virt_dma vmd wmi video [ 755.121002] CR2: 0000000000000000 The crash is because, for WCN7850, only ab->pdev[0] is initialized, while mac_id here is misused to retrieve pdev and it is not zero, leading to a NULL pointer access. Fix this issue by getting pdev_id first and then use it to retrieve pdev. Also fix some other code snippets which have the same issue. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230714080658.3140-1-quic_bqiang@quicinc.com
2023-08-02wifi: ath12k: avoid array overflow of hw mode for preferred_hw_modeWen Gong
Currently ath12k define WMI_HOST_HW_MODE_DBS_OR_SBS=5 as max hw mode for enum wmi_host_hw_mode_config_type, it is also same for the array ath12k_hw_mode_pri_map. When tested with new version firmware/board data which support new hw mode eMLSR mode with hw mode value 8, it leads overflow usage for array ath12k_hw_mode_pri_map in function ath12k_wmi_hw_mode_caps(), and then lead preferred_hw_mode changed to 8, and finally function ath12k_pull_mac_phy_cap_svc_ready_ext() select the capability of hw mode 8, but the capability of eMLSR mode report from firmware does not support 2.4 GHz band for WCN7850, so finally 2.4 GHz band is disabled. Skip the hw mode which exceeds WMI_HOST_HW_MODE_MAX in function ath12k_wmi_hw_mode_caps() helps to avoid array overflow, then the 2.4 GHz band will not be disabled. This is to keep compatibility with newer version firmware/board data files, this change is still needed after ath12k add eMLSR hw mode 8 in array ath12k_hw_mode_pri_map and enum wmi_host_hw_mode_config_type, because more hw mode maybe added in next firmware/board data version e.g hw mode 9, then it will also lead new array overflow without this change. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230714072405.28705-1-quic_wgong@quicinc.com
2023-08-02wifi: ath12k: fix memcpy array overflow in ath12k_peer_assoc_h_he()Arnd Bergmann
Two memory copies in this function copy from a short array into a longer one, using the wrong size, which leads to an out-of-bounds access: include/linux/fortify-string.h:592:4: error: call to '__read_overflow2_field' declared with 'warning' attribute: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror,-Wattribute-warning] __read_overflow2_field(q_size_field, size); ^ include/linux/fortify-string.h:592:4: error: call to '__read_overflow2_field' declared with 'warning' attribute: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror,-Wattribute-warning] 2 errors generated. Fixes: d889913205cf7 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230703123737.3420464-1-arnd@kernel.org
2023-08-02wifi: ath12k: correct the data_type from QMI_OPT_FLAG to QMI_UNSIGNED_1_BYTE ↵Wen Gong
for mlo_capable Currently, the encoding rule for field mlo_capable in struct qmi_wlanfw_host_cap_req_msg_v01 defined in array qmi_wlanfw_host_cap_req_msg_v01_ei uses type QMI_OPT_FLAG. Unfortunately, all ath12k firmware actually expects this field to be of type NON QMI_OPT_FLAG such as QMI_UNSIGNED_1_BYTE/QMI_UNSIGNED_8_BYTE... And as a result, firmware is unable to correctly decode the mlo_capable field. Change the ath12k definition as QMI_UNSIGNED_1_BYTE to match the firmware definition so that firmware can correctly parse the mlo_capable info from message QMI_WLANFW_HOST_CAP_REQ_V01 at wlan load time. This is just an accidental typo and that both WCN7850 and QCN9274 firmwares use QMI_UNSIGNED_1_BYTE. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726093857.3610-1-quic_wgong@quicinc.com
2023-08-02wifi: ath12k: Fix a NULL pointer dereference in ath12k_mac_op_hw_scan()Wen Gong
In ath12k_mac_op_hw_scan(), the return value of kzalloc() is directly used in memcpy(), which may lead to a NULL pointer dereference on failure of kzalloc(). Fix this bug by adding a check of arg.extraie.ptr. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726092625.3350-1-quic_wgong@quicinc.com
2023-08-02wifi: ath11k: Remove cal_done check during probeSeevalamuthu Mariappan
In some race conditions, calibration done QMI message is received even before host wait starts for calibration to be done. Due to this, resetting firmware was not performed after calibration. Hence, remove cal_done check in ath11k_qmi_fwreset_from_cold_boot() as this is called only from probe. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726141032.3061-4-quic_rajkbhag@quicinc.com
2023-08-02wifi: ath11k: Add coldboot calibration support for QCN9074Anilkumar Kolli
QCN9074 supports 6 GHz, which has increased number of channels compared to 5 GHz/2 GHz. So, to support coldboot calibration in QCN9074 ATH11K_COLD_BOOT_FW_RESET_DELAY extended to 60 seconds. To avoid code redundancy, fwreset_from_cold_boot moved to QMI and made common for both ahb and pci. Coldboot calibration is enabled only in FTM mode for QCN9074. QCN9074 requires firmware restart after coldboot, hence enable cbcal_restart_fw in hw_params. This support can be enabled/disabled using hw params for different hardware. Currently it is not enabled for QCA6390. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com> Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726141032.3061-3-quic_rajkbhag@quicinc.com
2023-08-02wifi: ath11k: Split coldboot calibration hw_paramSeevalamuthu Mariappan
QCN9074 enables coldboot calibration only in Factory Test Mode (FTM). Hence, split cold_boot_calib to two hw_params for mission and FTM mode. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726141032.3061-2-quic_rajkbhag@quicinc.com
2023-08-02wifi: ath11k: simplify ath11k_mac_validate_vht_he_fixed_rate_settings()Dmitry Antipov
In ath11k_mac_validate_vht_he_fixed_rate_settings() ar->ab->peers list is not altered so list_for_each_entry() should be safe. Compile tested only. Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726092113.78794-1-dmantipov@yandex.ru
2023-08-02wifi: ath11k: fix band selection for ppdu received in channel 177 of 5 GHzAditya Kumar Singh
5 GHz band channel 177 support was added with the commit e5e94d10c856 ("wifi: ath11k: add channel 177 into 5 GHz channel list"). However, during processing for the received ppdu in ath11k_dp_rx_h_ppdu(), channel number is checked only till 173. This leads to driver code checking for channel and then fetching the band from it which is extra effort since firmware has already given the channel number in the metadata. Fix this issue by checking the channel number till 177 since we support it now. Found via code review. Compile tested only. Fixes: e5e94d10c856 ("wifi: ath11k: add channel 177 into 5 GHz channel list") Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726044624.20507-1-quic_adisi@quicinc.com
2023-08-02net: Remove duplicated include in mac.cYang Li
./drivers/net/ethernet/freescale/fman/mac.c: linux/of_platform.h is included more than once. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6039 Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()Hans de Goede
Using brcmfmac with 6.5-rc3 on a brcmfmac43241b4-sdio triggers a backtrace caused by the following field-spanning warning: memcpy: detected field-spanning write (size 120) of single field "&params_le->channel_list[0]" at drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:1072 (size 2) The driver still works after this warning. The warning was introduced by the new field-spanning write checks which were enabled recently. Fix this by replacing the channel_list[1] declaration at the end of the struct with a flexible array declaration. Most users of struct brcmf_scan_params_le calculate the size to alloc using the size of the non flex-array part of the struct + needed extra space, so they do not care about sizeof(struct brcmf_scan_params_le). brcmf_notify_escan_complete() however uses the struct on the stack, expecting there to be room for at least 1 entry in the channel-list to store the special -1 abort channel-id. To make this work use an anonymous union with a padding member added + the actual channel_list flexible array. Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230729140500.27892-1-hdegoede@redhat.com
2023-08-02wifi: mwifiex: fix error recovery in PCIE buffer descriptor managementDmitry Antipov
Add missing 'kfree_skb()' in 'mwifiex_init_rxq_ring()' and never do 'kfree(card->rxbd_ring_vbase)' because this area is DMAed and should be released with 'dma_free_coherent()'. The latter is performed in 'mwifiex_pcie_delete_rxbd_ring()', which is now called to recover from possible errors in 'mwifiex_pcie_create_rxbd_ring()'. Likewise for 'mwifiex_pcie_init_evt_ring()', 'kfree(card->evtbd_ring_vbase)' 'mwifiex_pcie_delete_evtbd_ring()' and 'mwifiex_pcie_create_rxbd_ring()'. Fixes: d930faee141b ("mwifiex: add support for Marvell pcie8766 chipset") Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230731074334.56463-1-dmantipov@yandex.ru
2023-08-02wifi: brcmsmac: cleanup SCB-related data typesDmitry Antipov
Drop unused and set-but-unused fields of 'struct scb_ampdu_tid_ini', 'struct scb_ampdu' and 'struct scb', as well as now unused argument of 'brcms_c_ampdu_tx_operational()', adjust related code. Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230725162400.192357-2-dmantipov@yandex.ru
2023-08-02wifi: brcmsmac: remove more unused data typesDmitry Antipov
Remove unused 'struct brcmu_iovar' and 'struct tx_inst_power'. This follows commit b2090d93d4b6 ("wifi: brcmsmac: remove unused data type"). Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230725162400.192357-1-dmantipov@yandex.ru
2023-08-02wifi: mt76: Replace strlcpy() with strscpy()Azeem Shaikh
strlcpy() reads the entire source buffer first. This read may exceed the destination size limit. This is both inefficient and can lead to linear read overflows if a source string is not NUL-terminated [1]. In an effort to remove strlcpy() completely [2], replace strlcpy() here with strscpy(). Direct replacement is safe here since DEV_ASSIGN is only used by TRACE macros and the return values are ignored. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy [2] https://github.com/KSPP/linux/issues/89 Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230703181256.3712079-1-azeemshaikh38@gmail.com
2023-08-02net: ti: icssg-prueth: Add Power management supportMD Danish Anwar
Add suspend / resume APIs to support power management in ICSSG ethernet driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add ethtool ops for ICSSG Ethernet driverMD Danish Anwar
Add icssg_ethtool.c file. This file will be used for dumping statistics via ethtool for ICSSG ethernet driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add Standard network staticsticsMD Danish Anwar
Implement .ndo_get_stats64 to dump standard network interface statistics for ICSSG ethernet driver. Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add ICSSG StatsMD Danish Anwar
Add icssg_stats.c to help dump, icssg related driver statistics. ICSSG has hardware registers for providing statistics like total rx bytes, total tx bytes, etc. These registers are of 32 bits and hence in case of 1G link, they overflows in around 32 seconds. The behaviour of these registers is such that they don't roll back to 0 after overflow but rather stay at UINT_MAX. These registers support a feature where the value written to them is subtracted from the register. This feature can be utilized to fix the overflowing of stats. This solution uses a Workqueues based solution where a function gets called before the registers overflow (every 25 seconds in 1G link, 25000 seconds in 100M link), this function saves the register values in local variables and writes the last read value to the register. So any update during the read will be taken care of. Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add ICSSG ethernet driverRoger Quadros
This is the Ethernet driver for TI AM654 Silicon rev. 2 with the ICSSG PRU Sub-system running dual-EMAC firmware. The Programmable Real-time Unit and Industrial Communication Subsystem Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI SoCs. This subsystem is provided for the use cases like implementation of custom peripheral interfaces, offloading of tasks from the other processor cores of the SoC, etc. Every ICSSG core has two Programmable Real-Time Unit(PRUs), two auxiliary Real-Time Transfer Unit (RT_PRUs), and two Transmit Real-Time Transfer Units (TX_PRUs). Each one of these runs its own firmware. Every ICSSG core has two MII ports connect to these PRUs and also a MDIO port. The cores can run different firmwares to support different protocols and features like switch-dev, timestamping, etc. It uses System DMA to transfer and receive packets and shared memory register emulation between the firmware and driver for control and configuration. This patch adds support for basic EMAC functionality with 1Gbps and 100Mbps link speed. 10M and half duplex mode are not supported currently as they require IEP, the support for which will be added later. Support for switch-dev, timestamp, etc. will be added later by subsequent patch series. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add icssg queues APIs and macrosMD Danish Anwar
Add icssg_queue.c file. This file introduces macros and APIs related to ICSSG queues. These will be used by ICSSG Ethernet driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add Firmware config and classification APIs.MD Danish Anwar
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware configuration and classification related files. These will be used by ICSSG ethernet driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add mii helper apis and macrosMD Danish Anwar
Add MII helper APIs and MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has definition of prueth related structures. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: ti: icssg-prueth: Add Firmware Interface for ICSSG Ethernet driver.MD Danish Anwar
Add firmware interface related headers and macros for ICSSG Ethernet driver. These macros will be later used by the ICSSG ethernet driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02Merge tag 'mt76-for-kvalo-2023-07-31' of https://github.com/nbd168/wirelessKalle Valo
mt76 patches for 6.6 * fixes * preparation for mt7925 support * mt7981 support
2023-08-02net: dsa: mv88e6xxx: Add erratum 3.14 for 88E6390X and 88E6190XAnte Knezic
Fixes XAUI/RXAUI lane alignment errors. Issue causes dropped packets when trying to communicate over fiber via SERDES lanes of port 9 and 10. Errata document applies only to 88E6190X and 88E6390X devices. Requires poking in undocumented registers. Signed-off-by: Ante Knezic <ante.knezic@helmholz.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02octeontx2-pf: TC flower offload support for SPI fieldRatheesh Kannoth
Driver support to offload TC flower rules which matches against SPI field of IPSEC packets (AH/ESP). Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: tap_open(): set sk_uid from current_fsuid()Laszlo Ersek
Commit 66b2c338adce initializes the "sk_uid" field in the protocol socket (struct sock) from the "/dev/tapX" device node's owner UID. Per original commit 86741ec25462 ("net: core: Add a UID field to struct sock.", 2016-11-04), that's wrong: the idea is to cache the UID of the userspace process that creates the socket. Commit 86741ec25462 mentions socket() and accept(); with "tap", the action that creates the socket is open("/dev/tapX"). Therefore the device node's owner UID is irrelevant. In most cases, "/dev/tapX" will be owned by root, so in practice, commit 66b2c338adce has no observable effect: - before, "sk_uid" would be zero, due to undefined behavior (CVE-2023-1076), - after, "sk_uid" would be zero, due to "/dev/tapX" being owned by root. What matters is the (fs)UID of the process performing the open(), so cache that in "sk_uid". Cc: Eric Dumazet <edumazet@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Pietro Borrello <borrello@diag.uniroma1.it> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Fixes: 66b2c338adce ("tap: tap_open(): correctly initialize socket uid") Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435 Signed-off-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: tun_chr_open(): set sk_uid from current_fsuid()Laszlo Ersek
Commit a096ccca6e50 initializes the "sk_uid" field in the protocol socket (struct sock) from the "/dev/net/tun" device node's owner UID. Per original commit 86741ec25462 ("net: core: Add a UID field to struct sock.", 2016-11-04), that's wrong: the idea is to cache the UID of the userspace process that creates the socket. Commit 86741ec25462 mentions socket() and accept(); with "tun", the action that creates the socket is open("/dev/net/tun"). Therefore the device node's owner UID is irrelevant. In most cases, "/dev/net/tun" will be owned by root, so in practice, commit a096ccca6e50 has no observable effect: - before, "sk_uid" would be zero, due to undefined behavior (CVE-2023-1076), - after, "sk_uid" would be zero, due to "/dev/net/tun" being owned by root. What matters is the (fs)UID of the process performing the open(), so cache that in "sk_uid". Cc: Eric Dumazet <edumazet@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Pietro Borrello <borrello@diag.uniroma1.it> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Fixes: a096ccca6e50 ("tun: tun_chr_open(): correctly initialize socket uid") Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435 Signed-off-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: stmmac: dwmac-oxnas: remove obsolete dwmac glue driverNeil Armstrong
Due to lack of maintenance and stall of development for a few years now, and since no new features will ever be added upstream, remove support for OX810 and OX820 ethernet. Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Daniel Golle <daniel@makrotopia.org> Acked-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02net: stmmac: XGMAC support for mdio C22 addr > 3Rohan G Thomas
For XGMAC versions < 2.2 number of supported mdio C22 addresses is restricted to 3. From XGMAC version 2.2 there are no restrictions on the C22 addresses, it supports all valid mdio addresses(0 to 31). Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com> Acked-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-02can: c_can: Do not check for 0 return after calling platform_get_irq()Ruan Jinjie
It is not possible for platform_get_irq() to return 0. Use the return value from platform_get_irq(). Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com> Link: https://lore.kernel.org/all/20230802030900.2271322-1-ruanjinjie@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-08-01net: phy: nxp-c45-tja11xx: reset PCS if the link goes downRadu Pirea (NXP OSS)
During PTP testing on early TJA1120 engineering samples I observed that if the link is lost and recovered, the tx timestamps will be randomly lost. To avoid this HW issue, the PCS should be reset. Resetting the PCS will break the link and we should reset the PCS on LINK UP -> LINK DOWN transition, otherwise we will trigger and infinite loop of LINK UP -> LINK DOWN events. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-12-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: read ext trig ts on TJA1120Radu Pirea (NXP OSS)
On TJA1120, the external trigger timestamp now has a VALID bit. This changes the logic and we can't use the TJA1103 procedure. For TJA1103, we can always read a valid timestamp from the registers, compare the new timestamp with the old timestamp and, if they are not the same, an event occurred. This logic cannot be applied for TJA1120 because the timestamp is 0 if the VALID bit is not set. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Link: https://lore.kernel.org/r/20230731091619.77961-11-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: run cable test with the PHY in test modeRadu Pirea (NXP OSS)
For TJA1120, the enable bit for cable test is not writable if the PHY is not in test mode. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-10-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: handle FUSA irqRadu Pirea (NXP OSS)
TJA1120 and TJA1103 have a set of functional safety hardware tests executed after every reset, and when the tests are done, the IRQ line is asserted. For the moment, the purpose of these handlers is to acknowledge the IRQ and not to check the FUSA tests status. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-9-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: read egress ts on TJA1120Radu Pirea (NXP OSS)
The egress timestamp FIFO/circular buffer work different on TJA1120 than TJA1103. For TJA1103 the new timestamp should be manually moved from the FIFO to the hardware buffer before checking if the timestamp is valid. For TJA1120 the hardware will move automatically the new timestamp from the FIFO to the buffer and the user should check the valid bit, read the timestamp and unlock the buffer by writing any of the buffer registers(which are read only). Another change for the TJA1120 is the behaviour of the EGR TS IRQ bit. This bit was a self-clear bit for TJA1103, but now should be cleared before reading the timestamp. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Link: https://lore.kernel.org/r/20230731091619.77961-8-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: enable LTC sampling on both ext_ts edgesRadu Pirea (NXP OSS)
The external trigger configuration for TJA1120 has changed. The PHY supports sampling of the LTC on rising and on falling edge. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-7-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: add TJA1120 supportRadu Pirea (NXP OSS)
Add TJA1120 driver entry and its driver_data. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-6-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: use get_featuresRadu Pirea (NXP OSS)
PHY_BASIC_T1_FEATURES are not the right features supported by TJA1103 anymore. For example ethtool reports: [root@alarm ~]# ethtool end0 Settings for end0: Supported ports: [ TP ] Supported link modes: 100baseT1/Full 10baseT1L/Full 10baseT1L/Full is not supported by TJA1103 and supported ports list is not completed. The PHY also have a MII port. genphy_c45_pma_read_abilities implementation can detect the PHY features and they look like this. [root@alarm ~]# ethtool end0 Settings for end0: Supported ports: [ TP MII ] Supported link modes: 100baseT1/Full Supported pause frame use: Symmetric Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: 100baseT1/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: off master-slave cfg: forced master master-slave status: master Port: Twisted Pair PHYAD: 1 Transceiver: external MDI-X: Unknown Supports Wake-on: g Wake-on: d Link detected: yes SQI: 7/7 Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-5-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: prepare the ground for TJA1120Radu Pirea (NXP OSS)
Between TJA1120 and TJA1103 the hardware was improved, but some register addresses were changed and some bit fields were moved from one register to another. Introduce the nxp_c45_reg_field structure and its associated functions to abstract the differences between the PHYs. Remove the defined bits and register addresses that are not common between TJA1103 and TJA1120 and replace them with reg_fields and register addresses from phydev->drv->driver_data. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Link: https://lore.kernel.org/r/20230731091619.77961-4-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: remove RX BIST frame countersRadu Pirea (NXP OSS)
Remove RX BIST frame counters from the PHY statistics. In production mode, these counters are always read as 0. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-3-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01net: phy: nxp-c45-tja11xx: use phylib master/slave implementationRadu Pirea (NXP OSS)
Remove the custom implementation of master/save setup and read status and use genphy_c45_config_aneg and genphy_c45_read_status since phylib has support for master/slave setup and master/slave status. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731091619.77961-2-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01virtio_net: enable per queue interrupt coalesce featureGavin Li
Enable per queue interrupt coalesce feature bit in driver and validate its dependency with control queue. Signed-off-by: Gavin Li <gavinl@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Heng Qi <hengqi@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20230731070656.96411-4-gavinl@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01virtio_net: support per queue interrupt coalesce commandGavin Li
Add interrupt_coalesce config in send_queue and receive_queue to cache user config. Send per virtqueue interrupt moderation config to underlying device in order to have more efficient interrupt moderation and cpu utilization of guest VM. Additionally, address all the VQs when updating the global configuration, as now the individual VQs configuration can diverge from the global configuration. Signed-off-by: Gavin Li <gavinl@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Heng Qi <hengqi@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20230731070656.96411-3-gavinl@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-01virtio_net: extract interrupt coalescing settings to a structureGavin Li
Extract interrupt coalescing settings to a structure so that it could be reused in other data structures. Signed-off-by: Gavin Li <gavinl@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Heng Qi <hengqi@linux.alibaba.com> Link: https://lore.kernel.org/r/20230731070656.96411-2-gavinl@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2026-09-08 17:38:02 +0000