| Age | Commit message (Collapse) | Author |
|---|
|
If PF is down, firmware will returns 10 Mbit/s rate and half-duplex mode
when PF queries the port information from firmware.
After imp reset command is executed, PF status changes to down,
and PF will query link status and updates port information
from firmware in a periodic scheduled task.
However, there is a low probability that port information is updated
when PF is down, and then PF link status changes to up.
In this case, PF synchronizes incorrect rate and duplex mode to VF.
This patch fixes it by updating port information before
PF synchronizes the rate and duplex to the VF
when PF changes to up.
Fixes: 18b6e31f8bf4 ("net: hns3: PF add support for pushing link status to VFs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. We think firmware watchdog initialization is completed
before VF clear the interrupt source. However, firmware initialization
may not complete early. So VF will receive multiple reset interrupts
and fail to reset.
So we add delay before VF interrupt source and 5 ms delay
is enough to avoid second reset interrupt.
Fixes: 427900d27d86 ("net: hns3: fix the timing issue of VF clearing interrupt sources")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a VF is calling hns3_init_mac_addr(), get_mac_addr() may
return fail, then the value of mac_addr_temp is not initialized.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
debugfs
The hns3 driver define an array of string to show the coalesce
info, but if the kernel adds a new mode or a new state,
out-of-bounds access may occur when coalesce info is read via
debugfs, this patch fix the problem.
Fixes: c99fead7cb07 ("net: hns3: add debugfs support for interrupt coalesce")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the FEC capability bit is default set for device version V2.
It's incorrect for the copper port. Eventhough it doesn't make the nic
work abnormal, but the capability information display in debugfs may
confuse user. So clear it when driver get the port type inforamtion.
Fixes: 433ccce83504 ("net: hns3: use FEC capability queried from firmware")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In hclgevf_mbx_handler() and hclgevf_get_mbx_resp() functions,
there is a typical store-store and load-load scenario between
received_resp and additional_info. This patch adds barrier
to fix the problem.
Fixes: 4671042f1ef0 ("net: hns3: add match_id to check mailbox response from PF to VF")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hclge_sync_vlan_filter is called in periodic task,
trying to remove VLAN from vlan_del_fail_bmap. It can
be concurrence with VLAN adding operation from user.
So once user failed to delete a VLAN id, and add it
again soon, it may be removed by the periodic task,
which may cause the software configuration being
inconsistent with hardware. So add mutex handling
to avoid this.
user hns3 driver
periodic task
│
add vlan 10 ───── hns3_vlan_rx_add_vid │
│ (suppose success) │
│ │
del vlan 10 ───── hns3_vlan_rx_kill_vid │
│ (suppose fail,add to │
│ vlan_del_fail_bmap) │
│ │
add vlan 10 ───── hns3_vlan_rx_add_vid │
(suppose success) │
foreach vlan_del_fail_bmp
del vlan 10
Fixes: fe4144d47eef ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commands should be sorted inside the group definition.
Fix the ordering so we won't get following warning:
WARN_ON(iwl_cmd_groups_verify_sorted(trans_cfg))
Link: https://lore.kernel.org/regressions/2fa930bb-54dd-4942-a88d-05a47c8e9731@gmail.com/
Link: https://lore.kernel.org/linux-wireless/CAHk-=wix6kqQ5vHZXjOPpZBfM7mMm9bBZxi2Jh7XnaKCqVf94w@mail.gmail.com/
Fixes: b6e3d1ba4fcf ("wifi: iwlwifi: mvm: implement new firmware API for statistics")
Tested-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Tested-by: Damian Tometzki <damian@riscv-rocks.de>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We were just continuing in this case, surely not desired.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Analogously to prueth_remove, just also taking care for NULL'ing the
iep pointers.
Fixes: 186734c15886 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Fixes: 443a2367ba3c ("net: ti: icssg-prueth: am65x SR2.0 add 10M full duplex support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KMSAN reported the following uninit-value access issue:
=====================================================
BUG: KMSAN: uninit-value in ppp_sync_input drivers/net/ppp/ppp_synctty.c:690 [inline]
BUG: KMSAN: uninit-value in ppp_sync_receive+0xdc9/0xe70 drivers/net/ppp/ppp_synctty.c:334
ppp_sync_input drivers/net/ppp/ppp_synctty.c:690 [inline]
ppp_sync_receive+0xdc9/0xe70 drivers/net/ppp/ppp_synctty.c:334
tiocsti+0x328/0x450 drivers/tty/tty_io.c:2295
tty_ioctl+0x808/0x1920 drivers/tty/tty_io.c:2694
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x211/0x400 fs/ioctl.c:857
__x64_sys_ioctl+0x97/0xe0 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Uninit was created at:
__alloc_pages+0x75d/0xe80 mm/page_alloc.c:4591
__alloc_pages_node include/linux/gfp.h:238 [inline]
alloc_pages_node include/linux/gfp.h:261 [inline]
__page_frag_cache_refill+0x9a/0x2c0 mm/page_alloc.c:4691
page_frag_alloc_align+0x91/0x5d0 mm/page_alloc.c:4722
page_frag_alloc include/linux/gfp.h:322 [inline]
__netdev_alloc_skb+0x215/0x6d0 net/core/skbuff.c:728
netdev_alloc_skb include/linux/skbuff.h:3225 [inline]
dev_alloc_skb include/linux/skbuff.h:3238 [inline]
ppp_sync_input drivers/net/ppp/ppp_synctty.c:669 [inline]
ppp_sync_receive+0x237/0xe70 drivers/net/ppp/ppp_synctty.c:334
tiocsti+0x328/0x450 drivers/tty/tty_io.c:2295
tty_ioctl+0x808/0x1920 drivers/tty/tty_io.c:2694
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x211/0x400 fs/ioctl.c:857
__x64_sys_ioctl+0x97/0xe0 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
CPU: 0 PID: 12950 Comm: syz-executor.1 Not tainted 6.6.0-14500-g1c41041124bd #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc38 04/01/2014
=====================================================
ppp_sync_input() checks the first 2 bytes of the data are PPP_ALLSTATIONS
and PPP_UI. However, if the data length is 1 and the first byte is
PPP_ALLSTATIONS, an access to an uninitialized value occurs when checking
PPP_UI. This patch resolves this issue by checking the data length.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inspired by syzbot reports using a stack of multiple ipvlan devices.
Reduce stack size needed in ipvlan_process_v6_outbound() by moving
the flowi6 struct used for the route lookup in an non inlined
helper. ipvlan_route_v6_outbound() needs 120 bytes on the stack,
immediately reclaimed.
Also make sure ipvlan_process_v4_outbound() is not inlined.
We might also have to lower MAX_NEST_DEV, because only syzbot uses
setups with more than four stacked devices.
BUG: TASK stack guard page was hit at ffffc9000e803ff8 (stack is ffffc9000e804000..ffffc9000e808000)
stack guard page: 0000 [#1] SMP KASAN
CPU: 0 PID: 13442 Comm: syz-executor.4 Not tainted 6.1.52-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/09/2023
RIP: 0010:kasan_check_range+0x4/0x2a0 mm/kasan/generic.c:188
Code: 48 01 c6 48 89 c7 e8 db 4e c1 03 31 c0 5d c3 cc 0f 0b eb 02 0f 0b b8 ea ff ff ff 5d c3 cc 00 00 cc cc 00 00 cc cc 55 48 89 e5 <41> 57 41 56 41 55 41 54 53 b0 01 48 85 f6 0f 84 a4 01 00 00 48 89
RSP: 0018:ffffc9000e804000 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff817e5bf2
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffffffff887c6568
RBP: ffffc9000e804000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: dffffc0000000001 R12: 1ffff92001d0080c
R13: dffffc0000000000 R14: ffffffff87e6b100 R15: 0000000000000000
FS: 00007fd0c55826c0(0000) GS:ffff8881f6800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc9000e803ff8 CR3: 0000000170ef7000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<#DF>
</#DF>
<TASK>
[<ffffffff81f281d1>] __kasan_check_read+0x11/0x20 mm/kasan/shadow.c:31
[<ffffffff817e5bf2>] instrument_atomic_read include/linux/instrumented.h:72 [inline]
[<ffffffff817e5bf2>] _test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
[<ffffffff817e5bf2>] cpumask_test_cpu include/linux/cpumask.h:506 [inline]
[<ffffffff817e5bf2>] cpu_online include/linux/cpumask.h:1092 [inline]
[<ffffffff817e5bf2>] trace_lock_acquire include/trace/events/lock.h:24 [inline]
[<ffffffff817e5bf2>] lock_acquire+0xe2/0x590 kernel/locking/lockdep.c:5632
[<ffffffff8563221e>] rcu_lock_acquire+0x2e/0x40 include/linux/rcupdate.h:306
[<ffffffff8561464d>] rcu_read_lock include/linux/rcupdate.h:747 [inline]
[<ffffffff8561464d>] ip6_pol_route+0x15d/0x1440 net/ipv6/route.c:2221
[<ffffffff85618120>] ip6_pol_route_output+0x50/0x80 net/ipv6/route.c:2606
[<ffffffff856f65b5>] pol_lookup_func include/net/ip6_fib.h:584 [inline]
[<ffffffff856f65b5>] fib6_rule_lookup+0x265/0x620 net/ipv6/fib6_rules.c:116
[<ffffffff85618009>] ip6_route_output_flags_noref+0x2d9/0x3a0 net/ipv6/route.c:2638
[<ffffffff8561821a>] ip6_route_output_flags+0xca/0x340 net/ipv6/route.c:2651
[<ffffffff838bd5a3>] ip6_route_output include/net/ip6_route.h:100 [inline]
[<ffffffff838bd5a3>] ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:473 [inline]
[<ffffffff838bd5a3>] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:529 [inline]
[<ffffffff838bd5a3>] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
[<ffffffff838bd5a3>] ipvlan_queue_xmit+0xc33/0x1be0 drivers/net/ipvlan/ipvlan_core.c:677
[<ffffffff838c2909>] ipvlan_start_xmit+0x49/0x100 drivers/net/ipvlan/ipvlan_main.c:229
[<ffffffff84d03900>] netdev_start_xmit include/linux/netdevice.h:4966 [inline]
[<ffffffff84d03900>] xmit_one net/core/dev.c:3644 [inline]
[<ffffffff84d03900>] dev_hard_start_xmit+0x320/0x980 net/core/dev.c:3660
[<ffffffff84d080e2>] __dev_queue_xmit+0x16b2/0x3370 net/core/dev.c:4324
[<ffffffff855ce4cd>] dev_queue_xmit include/linux/netdevice.h:3067 [inline]
[<ffffffff855ce4cd>] neigh_hh_output include/net/neighbour.h:529 [inline]
[<ffffffff855ce4cd>] neigh_output include/net/neighbour.h:543 [inline]
[<ffffffff855ce4cd>] ip6_finish_output2+0x160d/0x1ae0 net/ipv6/ip6_output.c:139
[<ffffffff855b8616>] __ip6_finish_output net/ipv6/ip6_output.c:200 [inline]
[<ffffffff855b8616>] ip6_finish_output+0x6c6/0xb10 net/ipv6/ip6_output.c:211
[<ffffffff855b7e3c>] NF_HOOK_COND include/linux/netfilter.h:298 [inline]
[<ffffffff855b7e3c>] ip6_output+0x2bc/0x3d0 net/ipv6/ip6_output.c:232
[<ffffffff8575d27f>] dst_output include/net/dst.h:444 [inline]
[<ffffffff8575d27f>] ip6_local_out+0x10f/0x140 net/ipv6/output_core.c:161
[<ffffffff838bdae4>] ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:483 [inline]
[<ffffffff838bdae4>] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:529 [inline]
[<ffffffff838bdae4>] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
[<ffffffff838bdae4>] ipvlan_queue_xmit+0x1174/0x1be0 drivers/net/ipvlan/ipvlan_core.c:677
[<ffffffff838c2909>] ipvlan_start_xmit+0x49/0x100 drivers/net/ipvlan/ipvlan_main.c:229
[<ffffffff84d03900>] netdev_start_xmit include/linux/netdevice.h:4966 [inline]
[<ffffffff84d03900>] xmit_one net/core/dev.c:3644 [inline]
[<ffffffff84d03900>] dev_hard_start_xmit+0x320/0x980 net/core/dev.c:3660
[<ffffffff84d080e2>] __dev_queue_xmit+0x16b2/0x3370 net/core/dev.c:4324
[<ffffffff855ce4cd>] dev_queue_xmit include/linux/netdevice.h:3067 [inline]
[<ffffffff855ce4cd>] neigh_hh_output include/net/neighbour.h:529 [inline]
[<ffffffff855ce4cd>] neigh_output include/net/neighbour.h:543 [inline]
[<ffffffff855ce4cd>] ip6_finish_output2+0x160d/0x1ae0 net/ipv6/ip6_output.c:139
[<ffffffff855b8616>] __ip6_finish_output net/ipv6/ip6_output.c:200 [inline]
[<ffffffff855b8616>] ip6_finish_output+0x6c6/0xb10 net/ipv6/ip6_output.c:211
[<ffffffff855b7e3c>] NF_HOOK_COND include/linux/netfilter.h:298 [inline]
[<ffffffff855b7e3c>] ip6_output+0x2bc/0x3d0 net/ipv6/ip6_output.c:232
[<ffffffff8575d27f>] dst_output include/net/dst.h:444 [inline]
[<ffffffff8575d27f>] ip6_local_out+0x10f/0x140 net/ipv6/output_core.c:161
[<ffffffff838bdae4>] ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:483 [inline]
[<ffffffff838bdae4>] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:529 [inline]
[<ffffffff838bdae4>] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
[<ffffffff838bdae4>] ipvlan_queue_xmit+0x1174/0x1be0 drivers/net/ipvlan/ipvlan_core.c:677
[<ffffffff838c2909>] ipvlan_start_xmit+0x49/0x100 drivers/net/ipvlan/ipvlan_main.c:229
[<ffffffff84d03900>] netdev_start_xmit include/linux/netdevice.h:4966 [inline]
[<ffffffff84d03900>] xmit_one net/core/dev.c:3644 [inline]
[<ffffffff84d03900>] dev_hard_start_xmit+0x320/0x980 net/core/dev.c:3660
[<ffffffff84d080e2>] __dev_queue_xmit+0x16b2/0x3370 net/core/dev.c:4324
[<ffffffff855ce4cd>] dev_queue_xmit include/linux/netdevice.h:3067 [inline]
[<ffffffff855ce4cd>] neigh_hh_output include/net/neighbour.h:529 [inline]
[<ffffffff855ce4cd>] neigh_output include/net/neighbour.h:543 [inline]
[<ffffffff855ce4cd>] ip6_finish_output2+0x160d/0x1ae0 net/ipv6/ip6_output.c:139
[<ffffffff855b8616>] __ip6_finish_output net/ipv6/ip6_output.c:200 [inline]
[<ffffffff855b8616>] ip6_finish_output+0x6c6/0xb10 net/ipv6/ip6_output.c:211
[<ffffffff855b7e3c>] NF_HOOK_COND include/linux/netfilter.h:298 [inline]
[<ffffffff855b7e3c>] ip6_output+0x2bc/0x3d0 net/ipv6/ip6_output.c:232
[<ffffffff8575d27f>] dst_output include/net/dst.h:444 [inline]
[<ffffffff8575d27f>] ip6_local_out+0x10f/0x140 net/ipv6/output_core.c:161
[<ffffffff838bdae4>] ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:483 [inline]
[<ffffffff838bdae4>] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:529 [inline]
[<ffffffff838bdae4>] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
[<ffffffff838bdae4>] ipvlan_queue_xmit+0x1174/0x1be0 drivers/net/ipvlan/ipvlan_core.c:677
[<ffffffff838c2909>] ipvlan_start_xmit+0x49/0x100 drivers/net/ipvlan/ipvlan_main.c:229
[<ffffffff84d03900>] netdev_start_xmit include/linux/netdevice.h:4966 [inline]
[<ffffffff84d03900>] xmit_one net/core/dev.c:3644 [inline]
[<ffffffff84d03900>] dev_hard_start_xmit+0x320/0x980 net/core/dev.c:3660
[<ffffffff84d080e2>] __dev_queue_xmit+0x16b2/0x3370 net/core/dev.c:4324
[<ffffffff855ce4cd>] dev_queue_xmit include/linux/netdevice.h:3067 [inline]
[<ffffffff855ce4cd>] neigh_hh_output include/net/neighbour.h:529 [inline]
[<ffffffff855ce4cd>] neigh_output include/net/neighbour.h:543 [inline]
[<ffffffff855ce4cd>] ip6_finish_output2+0x160d/0x1ae0 net/ipv6/ip6_output.c:139
[<ffffffff855b8616>] __ip6_finish_output net/ipv6/ip6_output.c:200 [inline]
[<ffffffff855b8616>] ip6_finish_output+0x6c6/0xb10 net/ipv6/ip6_output.c:211
[<ffffffff855b7e3c>] NF_HOOK_COND include/linux/netfilter.h:298 [inline]
[<ffffffff855b7e3c>] ip6_output+0x2bc/0x3d0 net/ipv6/ip6_output.c:232
[<ffffffff8575d27f>] dst_output include/net/dst.h:444 [inline]
[<ffffffff8575d27f>] ip6_local_out+0x10f/0x140 net/ipv6/output_core.c:161
[<ffffffff838bdae4>] ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:483 [inline]
[<ffffffff838bdae4>] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:529 [inline]
[<ffffffff838bdae4>] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
[<ffffffff838bdae4>] ipvlan_queue_xmit+0x1174/0x1be0 drivers/net/ipvlan/ipvlan_core.c:677
[<ffffffff838c2909>] ipvlan_start_xmit+0x49/0x100 drivers/net/ipvlan/ipvlan_main.c:229
[<ffffffff84d03900>] netdev_start_xmit include/linux/netdevice.h:4966 [inline]
[<ffffffff84d03900>] xmit_one net/core/dev.c:3644 [inline]
[<ffffffff84d03900>] dev_hard_start_xmit+0x320/0x980 net/core/dev.c:3660
[<ffffffff84d080e2>] __dev_queue_xmit+0x16b2/0x3370 net/core/dev.c:4324
[<ffffffff84d4a65e>] dev_queue_xmit include/linux/netdevice.h:3067 [inline]
[<ffffffff84d4a65e>] neigh_resolve_output+0x64e/0x750 net/core/neighbour.c:1560
[<ffffffff855ce503>] neigh_output include/net/neighbour.h:545 [inline]
[<ffffffff855ce503>] ip6_finish_output2+0x1643/0x1ae0 net/ipv6/ip6_output.c:139
[<ffffffff855b8616>] __ip6_finish_output net/ipv6/ip6_output.c:200 [inline]
[<ffffffff855b8616>] ip6_finish_output+0x6c6/0xb10 net/ipv6/ip6_output.c:211
[<ffffffff855b7e3c>] NF_HOOK_COND include/linux/netfilter.h:298 [inline]
[<ffffffff855b7e3c>] ip6_output+0x2bc/0x3d0 net/ipv6/ip6_output.c:232
[<ffffffff855b9ce4>] dst_output include/net/dst.h:444 [inline]
[<ffffffff855b9ce4>] NF_HOOK include/linux/netfilter.h:309 [inline]
[<ffffffff855b9ce4>] ip6_xmit+0x11a4/0x1b20 net/ipv6/ip6_output.c:352
[<ffffffff8597984e>] sctp_v6_xmit+0x9ae/0x1230 net/sctp/ipv6.c:250
[<ffffffff8594623e>] sctp_packet_transmit+0x25de/0x2bc0 net/sctp/output.c:653
[<ffffffff858f5142>] sctp_packet_singleton+0x202/0x310 net/sctp/outqueue.c:783
[<ffffffff858ea411>] sctp_outq_flush_ctrl net/sctp/outqueue.c:914 [inline]
[<ffffffff858ea411>] sctp_outq_flush+0x661/0x3d40 net/sctp/outqueue.c:1212
[<ffffffff858f02f9>] sctp_outq_uncork+0x79/0xb0 net/sctp/outqueue.c:764
[<ffffffff8589f060>] sctp_side_effects net/sctp/sm_sideeffect.c:1199 [inline]
[<ffffffff8589f060>] sctp_do_sm+0x55c0/0x5c30 net/sctp/sm_sideeffect.c:1170
[<ffffffff85941567>] sctp_primitive_ASSOCIATE+0x97/0xc0 net/sctp/primitive.c:73
[<ffffffff859408b2>] sctp_sendmsg_to_asoc+0xf62/0x17b0 net/sctp/socket.c:1839
[<ffffffff85910b5e>] sctp_sendmsg+0x212e/0x33b0 net/sctp/socket.c:2029
[<ffffffff8544d559>] inet_sendmsg+0x149/0x310 net/ipv4/af_inet.c:849
[<ffffffff84c6c4d2>] sock_sendmsg_nosec net/socket.c:716 [inline]
[<ffffffff84c6c4d2>] sock_sendmsg net/socket.c:736 [inline]
[<ffffffff84c6c4d2>] ____sys_sendmsg+0x572/0x8c0 net/socket.c:2504
[<ffffffff84c6ca91>] ___sys_sendmsg net/socket.c:2558 [inline]
[<ffffffff84c6ca91>] __sys_sendmsg+0x271/0x360 net/socket.c:2587
[<ffffffff84c6cbff>] __do_sys_sendmsg net/socket.c:2596 [inline]
[<ffffffff84c6cbff>] __se_sys_sendmsg net/socket.c:2594 [inline]
[<ffffffff84c6cbff>] __x64_sys_sendmsg+0x7f/0x90 net/socket.c:2594
[<ffffffff85b32553>] do_syscall_x64 arch/x86/entry/common.c:51 [inline]
[<ffffffff85b32553>] do_syscall_64+0x53/0x80 arch/x86/entry/common.c:84
[<ffffffff85c00087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and bpf.
Current release - regressions:
- sched: fix SKB_NOT_DROPPED_YET splat under debug config
Current release - new code bugs:
- tcp:
- fix usec timestamps with TCP fastopen
- fix possible out-of-bounds reads in tcp_hash_fail()
- fix SYN option room calculation for TCP-AO
- tcp_sigpool: fix some off by one bugs
- bpf: fix compilation error without CGROUPS
- ptp:
- ptp_read() should not release queue
- fix tsevqs corruption
Previous releases - regressions:
- llc: verify mac len before reading mac header
Previous releases - always broken:
- bpf:
- fix check_stack_write_fixed_off() to correctly spill imm
- fix precision tracking for BPF_ALU | BPF_TO_BE | BPF_END
- check map->usercnt after timer->timer is assigned
- dsa: lan9303: consequently nested-lock physical MDIO
- dccp/tcp: call security_inet_conn_request() after setting IP addr
- tg3: fix the TX ring stall due to incorrect full ring handling
- phylink: initialize carrier state at creation
- ice: fix direction of VF rules in switchdev mode
Misc:
- fill in a bunch of missing MODULE_DESCRIPTION()s, more to come"
* tag 'net-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: ti: icss-iep: fix setting counter value
ptp: fix corrupted list in ptp_open
ptp: ptp_read should not release queue
net_sched: sch_fq: better validate TCA_FQ_WEIGHTS and TCA_FQ_PRIOMAP
net: kcm: fill in MODULE_DESCRIPTION()
net/sched: act_ct: Always fill offloading tuple iifidx
netfilter: nat: fix ipv6 nat redirect with mapped and scoped addresses
netfilter: xt_recent: fix (increase) ipv6 literal buffer length
ipvs: add missing module descriptions
netfilter: nf_tables: remove catchall element in GC sync path
netfilter: add missing module descriptions
drivers/net/ppp: use standard array-copy-function
net: enetc: shorten enetc_setup_xdp_prog() error message to fit NETLINK_MAX_FMTMSG_LEN
virtio/vsock: Fix uninit-value in virtio_transport_recv_pkt()
r8169: respect userspace disabling IFF_MULTICAST
selftests/bpf: get trusted cgrp from bpf_iter__cgroup directly
bpf: Let verifier consider {task,cgroup} is trusted in bpf_iter_reg
net: phylink: initialize carrier state at creation
test/vsock: add dobule bind connect test
test/vsock: refactor vsock_accept
...
|
|
Currently icss_iep_set_counter() writes the upper 32-bits of the
counter value to both the lower and upper counter registers, so
fix this by writing the appropriate value to the lower register.
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Link: https://lore.kernel.org/r/20231107120037.1513546-1-diogo.ivo@siemens.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-11-06 (ice)
This series contains updates to ice driver only.
Dave removes SR-IOV LAG attribute for only the interface being disabled
to allow for proper unwinding of all interfaces.
Michal Schmidt changes some LAG allocations from GFP_KERNEL to GFP_ATOMIC
due to non-allowed sleeping.
Aniruddha and Marcin fix redirection and drop rules for switchdev by
properly setting and marking egress/ingress type.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix VF-VF direction matching in drop rule in switchdev
ice: Fix VF-VF filter rules in switchdev mode
ice: lag: in RCU, use atomic allocation
ice: Fix SRIOV LAG disable on non-compliant aggregate
====================
Link: https://lore.kernel.org/r/20231107004844.655549-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-11-06 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera resolves a couple issues with devlink; removing a call to
devlink_port_type_clear() and ensuring devlink port is unregistered
after the net device.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix devlink port unregistering
i40e: Do not call devlink_port_type_clear()
====================
Link: https://lore.kernel.org/r/20231107003600.653796-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB031530EB6D98DCE4DF20766CBCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
rt2800 has a lot of registers to control the RTS enable/disable
status for different rates. And the driver control them via
rt2800_set_rts_threshold(). When RTS was disabled in user
interface, this function won't be called at all. This means that
the RTS is still 'on' for CCK and OFDM rates. So we'd better to
disable them by default because it should be like this. The RTS
for HT20 and HT40 is already default off so we don't need to
touch them. If we toggle the RTS status, these register bits
will be enable/disable again by rt2800_set_rts_threshold().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB03155DDB953155B7A2DE849ABCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
When I tried to fix the watchdog of rt2800, I found that sometimes
the watchdog can not reset the hung device. This is because the
queue is not completely stuck, it just becomes very slow. The MTK
vendor driver for the new chip MT7603/MT7612 has a DMA busy watchdog
to detect device hangs by checking DMA busy status. This watchdog
implementation is something similar to it. To reduce unnecessary
reset, we can check the INT_SOURCE_CSR register together as I found
that when the radio hung, the RX/TX coherent interrupt will always
stuck at triggered state.
The 'watchdog' module parameter has been extended to control all
watchdogs(0=disabled, 1=hang watchdog, 2=DMA watchdog, 3=both). This
new watchdog function is a slight schedule and it won't affect the
transmission speed. So we can turn on it by default. Due to the
INT_SOURCE_CSR register is invalid on rt2800 USB NICs, the DMA busy
watchdog will be automatically disabled for them.
Tested on MT7620 and RT5350.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315D7462CE08A119A99DE34BCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
The broadcast packets will be filtered in the FIF_ALLMULTI flag in
the original code, which causes beacon packets to be filtered out
and disconnection. Therefore, we fix it.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231103020851.102238-1-pkshih@realtek.com
|
|
Since 'ieee80211_txq_get_depth()' allows NULL for 2nd and
3rd arguments, simplify '__rtw_tx_work()' by dropping unused
'byte_cnt'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231102115606.69838-1-dmantipov@yandex.ru
|
|
content
To notify firmware TDMA timeslot assignment, append TDMA parameters when
sending policy H2C firmware command. However, compiler warns we do memcpy()
data to val[] field of TLV struct. To avoid this, assign the struct value
with simple '=' instead. Compile tested only.
rtw89/coex.c: In function '_append_tdma':
drivers/net/wireless/realtek/rtw89/coex.c:1585:17:
warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
1585 | memcpy(&v3->tdma, &dm->tdma, sizeof(v3->tdma));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/realtek/rtw89/coex.h:8,
from drivers/net/wireless/realtek/rtw89/coex.c:5:
drivers/net/wireless/realtek/rtw89/core.h:2703:37:
note: at offset [5714, 71249] into destination object 'ver' of size 8
2703 | const struct rtw89_btc_ver *ver;
| ^~~
drivers/net/wireless/realtek/rtw89/coex.c:1579:17:
warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
1579 | memcpy(v, &dm->tdma, sizeof(*v));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw89/core.h:2703:37:
note: at offset [5710, 71245] into destination object 'ver' of size 8
2703 | const struct rtw89_btc_ver *ver;
| ^~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310301908.Wrj0diqe-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231102003716.25815-1-pkshih@realtek.com
|
|
For normal use, we do additional settings than mac_pre_init, such as
more TX/RX DMA channels, interrupt mitigation and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-6-pkshih@realtek.com
|
|
PCI LTR (Latency Tolerance Reporting) is a capability to yield expected
power consumption, and we configure the parameters according to design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-5-pkshih@realtek.com
|
|
Call this function when doing MAC initialization at probe stage. It does
partial initial registers only, because we only need basic ability to
download firmware. The function to clear index is the sub-function,
so set its pointer as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-4-pkshih@realtek.com
|
|
clear PCI ring index
Use gen_def pointer to call three WiFi 6 specific functions, and add _ax
suffix to them. Then, we will implement functions for WiFi 7 chips later.
The mac_{pre,post}_init are used to initialize PCI during doing MAC
initialization, and clear PCI ring index to make index consistent between
driver, firmware and hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-3-pkshih@realtek.com
|
|
In order to reuse PCI initial and configuration flows, add struct
rtw89_pci_gen_def to abstract the differences between WiFi 6/7 generations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-2-pkshih@realtek.com
|
|
Simplify 'wilc_scan()' assuming 'struct wilc_priv *' is the only data
passed to '(*scan_result)()' callback and thus avoid typeless 'void *'
pointers in related code, including 'struct wilc_user_scan_req'.
Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231031171330.70399-2-dmantipov@yandex.ru
|
|
Remove set but otherwise unused 'ch' member of 'struct wilc_conn_info'
and avoid typeless 'void *' pointers in '(*conn_result)()' callback.
Likewise for 'wilc_parse_join_bss_param()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231031171330.70399-1-dmantipov@yandex.ru
|
|
Check for if the usb_alloc_urb() failed.
Fixes: 68d57a07bfe5 ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e8d4a19a-f251-4101-a89b-607345e938cb@moroto.mountain
|
|
No matter CLC is enabled or disabled, the driver should initialize
the default value 0xff for channel configuration of CLC. Otherwise,
the zero value would disable channels.
Reported-and-tested-by: Ben Greear <greearb@candelatech.com>
Closes: https://lore.kernel.org/all/2fb78387-d226-3193-8ca7-90040561b9ad@candelatech.com/
Fixes: 09382d8f8641 ("wifi: mt76: mt7921: update the channel usage when the regd domain changed")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/5a976ddf1f636b5cb809373501d3cfdc6d8de3e4.1698648737.git.deren.wu@mediatek.com
|
|
In ppp_generic.c, memdup_user() is utilized to copy a userspace array.
This is done without an overflow-check, which is, however, not critical
because the multiplicands are an unsigned short and struct sock_filter,
which is currently of size 8.
Regardless, string.h now provides memdup_array_user(), a wrapper for
copying userspace arrays in a standardized manner, which has the
advantage of making it more obvious to the reader that an array is being
copied.
The wrapper additionally performs an obligatory overflow check, saving
the reader the effort of analyzing the potential for overflow, and
making the code a bit more robust in case of future changes to the
multiplicands len * size.
Replace memdup_user() with memdup_array_user().
Suggested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NETLINK_MAX_FMTMSG_LEN
NETLINK_MAX_FMTMSG_LEN is currently hardcoded to 80, and we provide an
error printf-formatted string having 96 characters including the
terminating \0. Assuming each %d (representing a queue) gets replaced by
a number having at most 2 digits (a reasonable assumption), the final
string is also 96 characters wide, which is too much.
Reduce the verbiage a bit by removing some (partially) redundant words,
which makes the new printf-formatted string be 73 characters wide with
the trailing newline.
Fixes: 800db2d125c2 ("net: enetc: ensure we always have a minimum number of TXQs for stack")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/lkml/202311061336.4dsWMT1h-lkp@intel.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231106160311.616118-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
So far we ignore the setting of IFF_MULTICAST. Fix this and clear bit
AcceptMulticast if IFF_MULTICAST isn't set.
Note: Based on the implementations I've seen it doesn't seem to be 100% clear
what a driver is supposed to do if IFF_ALLMULTI is set but IFF_MULTICAST
is not. This patch is based on the understanding that IFF_MULTICAST has
precedence.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4a57ba02-d52d-4369-9f14-3565e6c1f7dc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX ring maintained by the tg3 driver can end up in the state, when it
has packets queued for sending but the NIC hardware is not informed, so no
progress is made. This leads to a multi-second interruption in network
traffic followed by dev_watchdog() firing and resetting the queue.
The specific sequence of steps is:
1. tg3_start_xmit() is called at least once and queues packet(s) without
updating tnapi->prodmbox (netdev_xmit_more() returns true)
2. tg3_start_xmit() is called with an SKB which causes tg3_tso_bug() to be
called.
3. tg3_tso_bug() determines that the SKB is too large, ...
if (unlikely(tg3_tx_avail(tnapi) <= frag_cnt_est)) {
... stops the queue, and returns NETDEV_TX_BUSY:
netif_tx_stop_queue(txq);
...
if (tg3_tx_avail(tnapi) <= frag_cnt_est)
return NETDEV_TX_BUSY;
4. Since all tg3_tso_bug() call sites directly return, the code updating
tnapi->prodmbox is skipped.
5. The queue is stuck now. tg3_start_xmit() is not called while the queue
is stopped. The NIC is not processing new packets because
tnapi->prodmbox wasn't updated. tg3_tx() is not called by
tg3_poll_work() because the all TX descriptions that could be freed has
been freed:
/* run TX completion thread */
if (tnapi->hw_status->idx[0].tx_consumer != tnapi->tx_cons) {
tg3_tx(tnapi);
6. Eventually, dev_watchdog() fires triggering a reset of the queue.
This fix makes sure that the tnapi->prodmbox update happens regardless of
the reason tg3_start_xmit() returned.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_cow_head() can change skb->head (and thus skb_shinfo(skb))
We must not cache skb_shinfo(skb) before skb_cow_head().
Fixes: 6818c4d5b3c2 ("idpf: add splitq start_xmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Joshua Hay <joshua.a.hay@intel.com>
Cc: Alan Brady <alan.brady@intel.com>
Cc: Madhu Chittim <madhu.chittim@intel.com>
Cc: Phani Burra <phani.r.burra@intel.com>
Cc: Sridhar Samudrala <sridhar.samudrala@intel.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Bailey Forrest <bcf@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231103200451.514047-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Dell R650xs servers hangs on reboot if tg3 driver calls
tg3_power_down.
This happens only if network adapters (BCM5720 for R650xs) were
initialized using SNP (e.g. by booting ipxe.efi).
The actual problem is on Dell side, but this fix allows servers
to come back alive after reboot.
Signed-off-by: George Shuklin <george.shuklin@gmail.com>
Fixes: 2ca1c94ce0b6 ("tg3: Disable tg3 device on system reboot to avoid triggering AER")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231103115029.83273-1-george.shuklin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When adding a drop rule on a VF, rule direction is not being set, which
results in it always being set to ingress (ICE_ESWITCH_FLTR_INGRESS
equals 0). Because of this, drop rules added on port representors don't
match any packets.
To fix it, set rule direction in drop action to egress when netdev is a
port representor, otherwise set it to ingress.
Fixes: 0960a27bd479 ("ice: Add direction metadata")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Any packet leaving VSI i.e VF's VSI is considered as
egress traffic by HW, thus failing to match the added
rule.
Mark the direction for redirect rules as below:
1. VF-VF - Egress
2. Uplink-VF - Ingress
3. VF-Uplink - Egress
4. Link_Partner-Uplink - Ingress
5. Link_Partner-VF - Ingress
Fixes: 0960a27bd479 ("ice: Add direction metadata")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Aniruddha Paul <aniruddha.paul@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Sleeping is not allowed in RCU read-side critical sections.
Use atomic allocations under rcu_read_lock.
Fixes: 1e0f9881ef79 ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Fixes: 41ccedf5ca8f ("ice: implement lag netdev event handler")
Fixes: 3579aa86fb40 ("ice: update reset path for SRIOV LAG support")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If an attribute of an aggregate interface disqualifies it from supporting
SRIOV, the driver will unwind the SRIOV support. Currently the driver is
clearing the feature bit for all interfaces in the aggregate, but this is
not allowing the other interfaces to unwind successfully on driver unload.
Only clear the feature bit for the interface that is currently unwinding.
Fixes: bf65da2eb279 ("ice: enforce interface eligibility and add messaging for SRIOV LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Ensure that devlink port is unregistered after unregistering
of net device.
Reproducer:
[root@host ~]# rmmod i40e
[ 4742.939386] i40e 0000:02:00.1: i40e_ptp_stop: removed PHC on enp2s0f1np1
[ 4743.059269] ------------[ cut here ]------------
[ 4743.063900] WARNING: CPU: 21 PID: 10766 at net/devlink/port.c:1078 devl_port_unregister+0x69/0x80
...
Fixes: 9e479d64dc58 ("i40e: Add initial devlink support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do not call devlink_port_type_clear() prior devlink port unregister
and let devlink core to take care about it.
Reproducer:
[root@host ~]# rmmod i40e
[ 4539.964699] i40e 0000:02:00.0: devlink port type for port 0 cleared without a software interface reference, device type not supported by the kernel?
[ 4540.319811] i40e 0000:02:00.1: devlink port type for port 1 cleared without a software interface reference, device type not supported by the kernel?
Fixes: 9e479d64dc58 ("i40e: Add initial devlink support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
On interface down, the pending SQEs in the NIX get dropped
or drained out during SMQ flush. But skb's pointed by these
SQEs never get free or updated to the stack as respective CQE
never get added.
This patch fixes the issue by freeing all valid skb's in SQ SG list.
Fixes: b1bc8457e9d0 ("octeontx2-pf: Cleanup all receive buffers in SG descriptor")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx_pause flag says that whether we support receiving Pause frames.
When a Pause frame is received TX is delayed for some time. This is TX
flow control. In the same manner tx_pause is actually RX flow control.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From XGMAC Core 3.20 and later, each Flexible PPS has individual PPSEN bit
to select Fixed mode or Flexible mode. The PPSEN must be set, or it stays
in Fixed PPS mode by default.
XGMAC Core prior 3.20, only PPSEN0(bit 4) is writable. PPSEN{1,2,3} are
read-only reserved, and they are already in Flexible mode by default, our
new code always set PPSEN{1,2,3} do not make things worse ;-)
Fixes: 95eaf3cd0a90 ("net: stmmac: dwxgmac: Add Flexible PPS support")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"As usual, lots of singleton and doubleton patches all over the tree
and there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- 'kdump: use generic functions to simplify crashkernel reservation
in arch', from Baoquan He. This is mainly cleanups and
consolidation of the 'crashkernel=' kernel parameter handling
- After much discussion, David Laight's 'minmax: Relax type checks in
min() and max()' is here. Hopefully reduces some typecasting and
the use of min_t() and max_t()
- A group of patches from Oleg Nesterov which clean up and slightly
fix our handling of reads from /proc/PID/task/... and which remove
task_struct.thread_group"
* tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (64 commits)
scripts/gdb/vmalloc: disable on no-MMU
scripts/gdb: fix usage of MOD_TEXT not defined when CONFIG_MODULES=n
.mailmap: add address mapping for Tomeu Vizoso
mailmap: update email address for Claudiu Beznea
tools/testing/selftests/mm/run_vmtests.sh: lower the ptrace permissions
.mailmap: map Benjamin Poirier's address
scripts/gdb: add lx_current support for riscv
ocfs2: fix a spelling typo in comment
proc: test ProtectionKey in proc-empty-vm test
proc: fix proc-empty-vm test with vsyscall
fs/proc/base.c: remove unneeded semicolon
do_io_accounting: use sig->stats_lock
do_io_accounting: use __for_each_thread()
ocfs2: replace BUG_ON() at ocfs2_num_free_extents() with ocfs2_error()
ocfs2: fix a typo in a comment
scripts/show_delta: add __main__ judgement before main code
treewide: mark stuff as __ro_after_init
fs: ocfs2: check status values
proc: test /proc/${pid}/statm
compiler.h: move __is_constexpr() to compiler.h
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add virtual-address based lskcipher interface
- Optimise ahash/shash performance in light of costly indirect calls
- Remove ahash alignmask attribute
Algorithms:
- Improve AES/XTS performance of 6-way unrolling for ppc
- Remove some uses of obsolete algorithms (md4, md5, sha1)
- Add FIPS 202 SHA-3 support in pkcs1pad
- Add fast path for single-page messages in adiantum
- Remove zlib-deflate
Drivers:
- Add support for S4 in meson RNG driver
- Add STM32MP13x support in stm32
- Add hwrng interface support in qcom-rng
- Add support for deflate algorithm in hisilicon/zip"
* tag 'v6.7-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (283 commits)
crypto: adiantum - flush destination page before unmapping
crypto: testmgr - move pkcs1pad(rsa,sha3-*) to correct place
Documentation/module-signing.txt: bring up to date
module: enable automatic module signing with FIPS 202 SHA-3
crypto: asymmetric_keys - allow FIPS 202 SHA-3 signatures
crypto: rsa-pkcs1pad - Add FIPS 202 SHA-3 support
crypto: FIPS 202 SHA-3 register in hash info for IMA
x509: Add OIDs for FIPS 202 SHA-3 hash and signatures
crypto: ahash - optimize performance when wrapping shash
crypto: ahash - check for shash type instead of not ahash type
crypto: hash - move "ahash wrapping shash" functions to ahash.c
crypto: talitos - stop using crypto_ahash::init
crypto: chelsio - stop using crypto_ahash::init
crypto: ahash - improve file comment
crypto: ahash - remove struct ahash_request_priv
crypto: ahash - remove crypto_ahash_alignmask
crypto: gcm - stop using alignmask of ahash
crypto: chacha20poly1305 - stop using alignmask of ahash
crypto: ccm - stop using alignmask of ahash
net: ipv6: stop checking crypto_ahash_alignmask
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"While the previously announced patch series for converting arch/sh to
device trees is not yet ready for inclusion to mainline and therefore
didn't make it for this pull request, there are still a small number
changes for v6.7 which include one platform (board plus CPU and driver
code) removal plus two fixes.
The removal sent in by Arnd Bergmann concerns the microdev board which
was an early SuperH prototype board that was never used in production.
With the board removed, we were able to drop the now unused code for
the SH4-202 CPU and well as the driver code for the superhyway bus and
a custom implementation for ioport_map() and ioport_unmap() which will
allow us to simplify ioport handling in the future.
Another patch set by Geert Uytterhoeven revives SuperH BIOS
earlyprintk support which got accidentally disabled in
e76fe57447e88916 ("sh: Remove old early serial console code V2"), the
second patch in the series updates the documentation.
Finally, a patch by Masami Hiramatsu fixes a regression reported by
the kernel test robot which uncovered that arch/sh is not implementing
arch_cmpxchg_local() and therefore needs use __generic_cmpxchg_local()
instead"
* tag 'sh-for-v6.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
locking/atomic: sh: Use generic_cmpxchg_local for arch_cmpxchg_local()
Documentation: kernel-parameters: Add earlyprintk=bios on SH
sh: bios: Revive earlyprintk support
sh: machvec: Remove custom ioport_{un,}map()
sh: Remove superhyway bus support
sh: Remove unused SH4-202 support
sh: Remove stale microdev board
|
