summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2024-03-28bnxt_en: Retry PTP TX timestamp from FW for 1 secondPavan Chebbi
Use a new default 1 second timeout value instead of the existing 1 msec value. The driver will keep track of the remaining time before timeout and will pass this value to bnxt_hwrm_port_ts_query(). The firmware supports timeout values up to 65535 usecs. If the timeout value passed to bnxt_hwrm_port_ts_query() is less than the FW max value, we will use that value to precisely control the specified timeout. If it is larger than the FW max value, we will use the FW max value and any additional retry to reach the desired timeout will be done in the context of bnxt_ptp_ts_aux_eork(). Link: https://lore.kernel.org/netdev/20240229070202.107488-2-michael.chan@broadcom.com/ Cc: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://lore.kernel.org/r/20240325222902.220712-3-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28bnxt_en: Add a timeout parameter to bnxt_hwrm_port_ts_query()Michael Chan
The caller can pass this new timeout parameter to the function to specify the firmware timeout value when requesting the TX timestamp from the firmware. This will allow the caller to precisely control the timeout and will be used in the next patch. In this patch, the parameter is 0 which means to use the current default value. Cc: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://lore.kernel.org/r/20240325222902.220712-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: pcs: rzn1-miic: Init RX clock early if MAC requires itRomain Gantois
The GMAC1 controller in the RZN1 IP requires the RX MII clock signal to be started before it initializes its own hardware, thus before it calls phylink_start. Implement the pcs_pre_init() callback so that the RX clock signal can be enabled early if necessary. Reported-by: Clément Léger <clement.leger@bootlin.com> Link: https://lore.kernel.org/linux-arm-kernel/20230116103926.276869-4-clement.leger@bootlin.com/ Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-7-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: phy: qcom: at803x: Avoid hibernating if MAC requires RX clockRussell King (Oracle)
Stmmac controllers connected to an at803x PHY cannot resume properly after suspend when WoL is enabled. This happens because the MAC requires an RX clock generated by the PHY to initialize its hardware properly. But the RX clock is cut when the PHY suspends and isn't brought up until the MAC driver resumes the phylink. Prevent the at803x PHY driver from going into suspend if the attached MAC driver always requires an RX clock signal. Reported-by: Clark Wang <xiaoning.wang@nxp.com> Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@nxp.com/ Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> [rgantois: commit log] Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-6-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: stmmac: Signal to PHY/PCS drivers to keep RX clock onRomain Gantois
There is a reocurring issue with stmmac controllers where the MAC fails to initialize its hardware if an RX clock signal isn't provided on the MAC/PHY link. This causes issues when PHY or PCS devices either go into suspend while cutting the RX clock or do not bring the clock signal up early enough for the MAC to initialize successfully. Set the mac_requires_rxc flag in the stmmac phylink config so that PHY/PCS drivers know to keep the RX clock up at all times. Reported-by: Clark Wang <xiaoning.wang@nxp.com> Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@nxp.com/ Reported-by: Clément Léger <clement.leger@bootlin.com> Link: https://lore.kernel.org/linux-arm-kernel/20230116103926.276869-4-clement.leger@bootlin.com/ Co-developed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-5-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: stmmac: Support a generic PCS field in mac_device_infoRomain Gantois
Global stmmac support for early initialization of PCS devices requires a generic PCS reference that can be passed to phylink_pcs_pre_init(). Currently, the mac_device_info struct contains only one PCS field, which is specific to the Lynx model. As PCS models are hardware-specific, it is more appropriate to have a generic PCS field in the mac_device_info struct. Refactor the lynx_pcs field into a generic phylink_pcs field. Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-4-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: stmmac: don't rely on lynx_pcs presence to check for a PHYMaxime Chevallier
When initializing attached PHYs, there are some cases where we don't expect any PHY to be connected. The logic uses conditions based on various local PCS configuration, but also calls-in phylink_expects_phy() via stmmac_init_phy(), which is enough to ensure we don't try to initialize a PHY when using a Lynx PCS, as long as we have the phy_interface set to a 802.3z mode and are using inband negociation. Drop the lynx check, making the stmmac generic code more pcs_lynx-agnostic. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> [rgantois: commit log] Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-3-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: phylink: add rxc_always_on flag to phylink_pcsRomain Gantois
Some MAC drivers (e.g. stmmac) require a continuous receive clock signal to be generated by a PCS that is handled by a standalone PCS driver. Such a PCS driver does not have access to a PHY device, thus cannot check the PHY_F_RXC_ALWAYS_ON flag. They cannot check max_requires_rxc in the phylink config either, since it is a private member. Therefore, a new flag is needed to signal to the PCS that it should keep the RX clock signal up at all times. Co-developed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-2-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: phylink: add PHY_F_RXC_ALWAYS_ON to PHY dev flagsRussell King (Oracle)
Some MAC controllers (e.g. stmmac) require their connected PHY to continuously provide a receive clock signal. This can cause issues in two cases: 1. The clock signal hasn't been started yet by the time the MAC driver initializes its hardware. This can make the initialization fail, as in the case of the rzn1 GMAC1 driver. 2. The clock signal is cut during a power saving event. By the time the MAC is brought back up, the clock signal is still not active since phylink_start hasn't been called yet. This brings us back to case 1. If a PHY driver reads this flag, it should ensure that the receive clock signal is started as soon as possible, and that it isn't brought down when the PHY goes into suspend. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> [rgantois: commit log] Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-1-24a74e5c761f@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28Merge branch '1GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-03-27 (e1000e) This series contains updates to e1000e driver only. Vitaly adds retry mechanism for some PHY operations to workaround MDI error and moves SMBus configuration to avoid possible PHY loss. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue e1000e: Workaround for sporadic MDI error on Meteor Lake systems ==================== Link: https://lore.kernel.org/r/20240327185517.2587564-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28idpf: sprinkle __counted_by{,_le}() in the virtchnl2 headerAlexander Lobakin
Both virtchnl2.h and its consumer idpf_virtchnl.c are very error-prone. There are 10 structures with flexible arrays at the end, but 9 of them has flex member counter in Little Endian. Make the code a bit more robust by applying __counted_by_le() to those 9. LE platforms is the main target for this driver, so they would receive additional protection. While we're here, add __counted_by() to virtchnl2_ptype::proto_id, as its counter is `u8` regardless of the Endianness. Compile test on x86_64 (LE) didn't reveal any new issues after applying the attributes. Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://lore.kernel.org/r/20240327142241.1745989-4-aleksander.lobakin@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28idpf: make virtchnl2.h self-containedAlexander Lobakin
To ease maintaining of virtchnl2.h, which already is messy enough, make it self-contained by adding missing if_ether.h include due to %ETH_ALEN usage. At the same time, virtchnl2_lan_desc.h is not used anywhere in the file, so move this include to idpf_txrx.h to speed up C preprocessing. Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://lore.kernel.org/r/20240327142241.1745989-3-aleksander.lobakin@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28net: remove gfp_mask from napi_alloc_skb()Jakub Kicinski
__napi_alloc_skb() is napi_alloc_skb() with the added flexibility of choosing gfp_mask. This is a NAPI function, so GFP_ATOMIC is implied. The only practical choice the caller has is whether to set __GFP_NOWARN. But that's a false choice, too, allocation failures in atomic context will happen, and printing warnings in logs, effectively for a packet drop, is both too much and very likely non-actionable. This leads me to a conclusion that most uses of napi_alloc_skb() are simply misguided, and should use __GFP_NOWARN in the first place. We also have a "standard" way of reporting allocation failures via the queue stat API (qstats::rx-alloc-fail). The direct motivation for this patch is that one of the drivers used at Meta calls napi_alloc_skb() (so prior to this patch without __GFP_NOWARN), and the resulting OOM warning is the top networking warning in our fleet. Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240327040213.3153864-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28xen-netfront: Add missing skb_mark_for_recycleJesper Dangaard Brouer
Notice that skb_mark_for_recycle() is introduced later than fixes tag in commit 6a5bcd84e886 ("page_pool: Allow drivers to hint on SKB recycling"). It is believed that fixes tag were missing a call to page_pool_release_page() between v5.9 to v5.14, after which is should have used skb_mark_for_recycle(). Since v6.6 the call page_pool_release_page() were removed (in commit 535b9c61bdef ("net: page_pool: hide page_pool_release_page()") and remaining callers converted (in commit 6bfef2ec0172 ("Merge branch 'net-page_pool-remove-page_pool_release_page'")). This leak became visible in v6.8 via commit dba1b8a7ab68 ("mm/page_pool: catch page_pool memory leaks"). Cc: stable@vger.kernel.org Fixes: 6c5aa6fc4def ("xen networking: add basic XDP support for xen-netfront") Reported-by: Leonidas Spyropoulos <artafinde@archlinux.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=218654 Reported-by: Arthur Borsboom <arthurborsboom@gmail.com> Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/171154167446.2671062.9127105384591237363.stgit@firesoul Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28qed: Drop useless pci_params.pm_capBjorn Helgaas
qed_init_pci() used pci_params.pm_cap only to cache the pci_dev.pm_cap. Drop the cache and use pci_dev.pm_cap directly. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240325224931.1462051-1-helgaas@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28gve: Add counter adminq_get_ptype_map_cnt to stats reportJohn Fraker
This counter counts the number of times get_ptype_map is executed on the admin queue, and was previously missing from the stats report. Signed-off-by: John Fraker <jfraker@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240325223308.618671-1-jfraker@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28ravb: Add support for an optional MDIO modeNiklas Söderlund
The driver used the DT node of the device itself when registering the MDIO bus. While this works, it creates a problem: it forces any MDIO bus properties to also be set on the devices DT node. This mixes the properties of two distinctly different things and is confusing. This change adds support for an optional mdio node to be defined as a child to the device DT node. The child node can then be used to describe MDIO bus properties that the MDIO core can act on when registering the bus. If no mdio child node is found the driver fallback to the old behavior and register the MDIO bus using the device DT node. This change is backward compatible with old bindings in use. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240325153451.2366083-3-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-29wifi: rtw88: station mode only for SDIO chipsPing-Ke Shih
Since only station mode has been tested on SDIO chips, only keep it support for SDIO chips to reflect correct supported features. Link: https://lore.kernel.org/linux-wireless/87wmpu1do6.fsf@kernel.org/T/#t Link: https://lore.kernel.org/linux-wireless/36972ff5-0c48-4bd2-8f9a-9649bfa24225@lexina.in/ Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://msgid.link/20240327004155.7172-1-pkshih@realtek.com
2024-03-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR. No conflicts, or adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-28Merge tag 'net-6.9-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from bpf, WiFi and netfilter. Current release - regressions: - ipv6: fix address dump when IPv6 is disabled on an interface Current release - new code bugs: - bpf: temporarily disable atomic operations in BPF arena - nexthop: fix uninitialized variable in nla_put_nh_group_stats() Previous releases - regressions: - bpf: protect against int overflow for stack access size - hsr: fix the promiscuous mode in offload mode - wifi: don't always use FW dump trig - tls: adjust recv return with async crypto and failed copy to userspace - tcp: properly terminate timers for kernel sockets - ice: fix memory corruption bug with suspend and rebuild - at803x: fix kernel panic with at8031_probe - qeth: handle deferred cc1 Previous releases - always broken: - bpf: fix bug in BPF_LDX_MEMSX - netfilter: reject table flag and netdev basechain updates - inet_defrag: prevent sk release while still in use - wifi: pick the version of SESSION_PROTECTION_NOTIF - wwan: t7xx: split 64bit accesses to fix alignment issues - mlxbf_gige: call request_irq() after NAPI initialized - hns3: fix kernel crash when devlink reload during pf initialization" * tag 'net-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits) inet: inet_defrag: prevent sk release while still in use Octeontx2-af: fix pause frame configuration in GMP mode net: lan743x: Add set RFE read fifo threshold for PCI1x1x chips net: bcmasp: Remove phy_{suspend/resume} net: bcmasp: Bring up unimac after PHY link up net: phy: qcom: at803x: fix kernel panic with at8031_probe netfilter: arptables: Select NETFILTER_FAMILY_ARP when building arp_tables.c netfilter: nf_tables: skip netdev hook unregistration if table is dormant netfilter: nf_tables: reject table flag and netdev basechain updates netfilter: nf_tables: reject destroy command to remove basechain hooks bpf: update BPF LSM designated reviewer list bpf: Protect against int overflow for stack access size bpf: Check bloom filter map value size bpf: fix warning for crash_kexec selftests: netdevsim: set test timeout to 10 minutes net: wan: framer: Add missing static inline qualifiers mlxbf_gige: call request_irq() after NAPI initialized tls: get psock ref after taking rxlock to avoid leak selftests: tls: add test with a partially invalid iov tls: adjust recv return with async crypto and failed copy to userspace ...
2024-03-28wifi: mt76: mt7915: workaround dubious x | !y warningKalle Valo
Sparse warns: drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c:526:9: warning: dubious: x | !y Workaround it by using the '?' operator. Compile tested only. Signed-off-by: Kalle Valo <kvalo@kernel.org> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240325155838.1558680-1-kvalo@kernel.org
2024-03-28wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warningsGustavo A. R. Silva
-Wflex-array-member-not-at-end is coming in GCC-14, and we are getting ready to enable it globally. There is currently an object (`header`), at the beginning of multiple structures, that contains a flexible structure (`struct mwl8k_cmd_pkt`), for example: struct mwl8k_cmd_get_hw_spec_sta { struct mwl8k_cmd_pkt header; ... __le32 num_tx_desc_per_queue; __le32 total_rxd; } __packed; So, in order to avoid ending up with flexible-array members in the middle of multiple other structs, we use the `__struct_group()` helper to separate the flexible array from the rest of the members in the flexible structure: struct mwl8k_cmd_pkt { __struct_group(mwl8k_cmd_pkt_hdr, hdr, __packed, ... the rest of the members ); char payload[]; } __packed; With the change described above, we now declare objects of the type of the tagged struct, in this case `struct mwl8k_cmd_pkt_hdr`, without embedding flexible arrays in the middle of another struct: struct mwl8k_cmd_get_hw_spec_sta { struct mwl8k_cmd_pkt_hdr header; ... __le32 num_tx_desc_per_queue; __le32 total_rxd; } __packed; Also, update the type of a couple of variables and function parameters from `struct mwl8k_cmd_pkt` to `struct mwl8k_cmd_pkt_hdr`. So, with these changes, fix 33 of the following warnings[1]: drivers/net/wireless/marvell/mwl8k.c:2353:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] Link: https://gist.github.com/GustavoARSilva/7a841a92c0f24e5efdb30ce02b601eb8 [1] Link: https://github.com/KSPP/linux/issues/202 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/ZgDrhe5pbV/WvDiZ@neat
2024-03-28wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warningsGustavo A. R. Silva
-Wflex-array-member-not-at-end is coming in GCC-14, and we are getting ready to enable it globally. Remove unused flexible-array members in multiple structures, and fix a hundred -Wflex-array-member-not-at-end warnings[1] in drivers/wireless/ti/ Link: https://gist.github.com/GustavoARSilva/fbf63c114d01319bbd19baf95b4d704b [1] Link: https://github.com/KSPP/linux/issues/202 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/ZgDcwIgxkhs6ZVdY@neat
2024-03-28Octeontx2-af: fix pause frame configuration in GMP modeHariprasad Kelam
The Octeontx2 MAC block (CGX) has separate data paths (SMU and GMP) for different speeds, allowing for efficient data transfer. The previous patch which added pause frame configuration has a bug due to which pause frame feature is not working in GMP mode. This patch fixes the issue by configurating appropriate registers. Fixes: f7e086e754fe ("octeontx2-af: Pause frame configuration at cgx") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240326052720.4441-1-hkelam@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-28net: lan743x: Add set RFE read fifo threshold for PCI1x1x chipsRaju Lakkaraju
PCI11x1x Rev B0 devices might drop packets when receiving back to back frames at 2.5G link speed. Change the B0 Rev device's Receive filtering Engine FIFO threshold parameter from its hardware default of 4 to 3 dwords to prevent the problem. Rev C0 and later hardware already defaults to 3 dwords. Fixes: bb4f6bffe33c ("net: lan743x: Add PCI11010 / PCI11414 device IDs") Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240326065805.686128-1-Raju.Lakkaraju@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-28net: bcmasp: Remove phy_{suspend/resume}Justin Chen
phy_{suspend/resume} is redundant. It gets called from phy_{stop/start}. Fixes: 490cb412007d ("net: bcmasp: Add support for ASP2.0 Ethernet controller") Signed-off-by: Justin Chen <justin.chen@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-28net: bcmasp: Bring up unimac after PHY link upJustin Chen
The unimac requires the PHY RX clk during reset or it may be put into a bad state. Bring up the unimac after link up to ensure the PHY RX clk exists. Fixes: 490cb412007d ("net: bcmasp: Add support for ASP2.0 Ethernet controller") Signed-off-by: Justin Chen <justin.chen@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-28net: phy: qcom: at803x: fix kernel panic with at8031_probeChristian Marangi
On reworking and splitting the at803x driver, in splitting function of at803x PHYs it was added a NULL dereference bug where priv is referenced before it's actually allocated and then is tried to write to for the is_1000basex and is_fiber variables in the case of at8031, writing on the wrong address. Fix this by correctly setting priv local variable only after at803x_probe is called and actually allocates priv in the phydev struct. Reported-by: William Wortel <wwortel@dorpstraat.com> Cc: <stable@vger.kernel.org> Fixes: 25d2ba94005f ("net: phy: at803x: move specific at8031 probe mode check to dedicated probe") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240325190621.2665-1-ansuelsmth@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-27Merge tag 'wireless-2024-03-27' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless Kalle Valo says: ==================== wireless fixes for v6.9-rc2 The first fixes for v6.9. Ping-Ke Shih now maintains a separate tree for Realtek drivers, document that in the MAINTAINERS. Plenty of fixes for both to stack and iwlwifi. Our kunit tests were working only on um architecture but that's fixed now. * tag 'wireless-2024-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (21 commits) MAINTAINERS: wifi: mwifiex: add Francesco as reviewer kunit: fix wireless test dependencies wifi: iwlwifi: mvm: include link ID when releasing frames wifi: iwlwifi: mvm: handle debugfs names more carefully wifi: iwlwifi: mvm: guard against invalid STA ID on removal wifi: iwlwifi: read txq->read_ptr under lock wifi: iwlwifi: fw: don't always use FW dump trig wifi: iwlwifi: mvm: rfi: fix potential response leaks wifi: mac80211: correctly set active links upon TTLM wifi: iwlwifi: mvm: Configure the link mapping for non-MLD FW wifi: iwlwifi: mvm: consider having one active link wifi: iwlwifi: mvm: pick the version of SESSION_PROTECTION_NOTIF wifi: mac80211: fix prep_connection error path wifi: cfg80211: fix rdev_dump_mpp() arguments order wifi: iwlwifi: mvm: disable MLO for the time being wifi: cfg80211: add a flag to disable wireless extensions wifi: mac80211: fix ieee80211_bss_*_flags kernel-doc wifi: mac80211: check/clear fast rx for non-4addr sta VLAN changes wifi: mac80211: fix mlme_link_id_dbg() MAINTAINERS: wifi: add git tree for Realtek WiFi drivers ... ==================== Link: https://lore.kernel.org/r/20240327191346.1A1EAC433C7@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-27e1000e: move force SMBUS from enable ulp function to avoid PHY loss issueVitaly Lifshits
Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on some systems. It is suspected to be caused by initiating PHY transactions before the interface settles. Separating this configuration from the ULP enabling flow and moving it to the shutdown function allows enough time for the interface to settle and avoids adding a delay. Fixes: 6607c99e7034 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state") Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-27e1000e: Workaround for sporadic MDI error on Meteor Lake systemsVitaly Lifshits
On some Meteor Lake systems accessing the PHY via the MDIO interface may result in an MDI error. This issue happens sporadically and in most cases a second access to the PHY via the MDIO interface results in success. As a workaround, introduce a retry counter which is set to 3 on Meteor Lake systems. The driver will only return an error if 3 consecutive PHY access attempts fail. The retry mechanism is disabled in specific flows, where MDI errors are expected. Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake") Suggested-by: Nikolay Mushayev <nikolay.mushayev@intel.com> Co-developed-by: Nir Efrati <nir.efrati@intel.com> Signed-off-by: Nir Efrati <nir.efrati@intel.com> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-03-25 (ice, ixgbe, igc) This series contains updates to ice, ixgbe, and igc drivers. Steven fixes incorrect casting of bitmap type for ice driver. Jesse fixes memory corruption issue with suspend flow on ice. Przemek adds GFP_ATOMIC flag to avoid sleeping in IRQ context for ixgbe. Kurt Kanzenbach removes no longer valid comment on igc. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: igc: Remove stale comment about Tx timestamping ixgbe: avoid sleeping allocation in ixgbe_ipsec_vf_add_sa() ice: fix memory corruption bug with suspend and rebuild ice: Refactor FW data type and fix bitmap casting issue ==================== Link: https://lore.kernel.org/r/20240325200659.993749-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-26mlxbf_gige: call request_irq() after NAPI initializedDavid Thompson
The mlxbf_gige driver encounters a NULL pointer exception in mlxbf_gige_open() when kdump is enabled. The sequence to reproduce the exception is as follows: a) enable kdump b) trigger kdump via "echo c > /proc/sysrq-trigger" c) kdump kernel executes d) kdump kernel loads mlxbf_gige module e) the mlxbf_gige module runs its open() as the the "oob_net0" interface is brought up f) mlxbf_gige module will experience an exception during its open(), something like: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000086000004 EC = 0x21: IABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e29a4000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000086000004 [#1] SMP CPU: 0 PID: 812 Comm: NetworkManager Tainted: G OE 5.15.0-1035-bluefield #37-Ubuntu Hardware name: https://www.mellanox.com BlueField-3 SmartNIC Main Card/BlueField-3 SmartNIC Main Card, BIOS 4.6.0.13024 Jan 19 2024 pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : 0x0 lr : __napi_poll+0x40/0x230 sp : ffff800008003e00 x29: ffff800008003e00 x28: 0000000000000000 x27: 00000000ffffffff x26: ffff000066027238 x25: ffff00007cedec00 x24: ffff800008003ec8 x23: 000000000000012c x22: ffff800008003eb7 x21: 0000000000000000 x20: 0000000000000001 x19: ffff000066027238 x18: 0000000000000000 x17: ffff578fcb450000 x16: ffffa870b083c7c0 x15: 0000aaab010441d0 x14: 0000000000000001 x13: 00726f7272655f65 x12: 6769675f6662786c x11: 0000000000000000 x10: 0000000000000000 x9 : ffffa870b0842398 x8 : 0000000000000004 x7 : fe5a48b9069706ea x6 : 17fdb11fc84ae0d2 x5 : d94a82549d594f35 x4 : 0000000000000000 x3 : 0000000000400100 x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000066027238 Call trace: 0x0 net_rx_action+0x178/0x360 __do_softirq+0x15c/0x428 __irq_exit_rcu+0xac/0xec irq_exit+0x18/0x2c handle_domain_irq+0x6c/0xa0 gic_handle_irq+0xec/0x1b0 call_on_irq_stack+0x20/0x2c do_interrupt_handler+0x5c/0x70 el1_interrupt+0x30/0x50 el1h_64_irq_handler+0x18/0x2c el1h_64_irq+0x7c/0x80 __setup_irq+0x4c0/0x950 request_threaded_irq+0xf4/0x1bc mlxbf_gige_request_irqs+0x68/0x110 [mlxbf_gige] mlxbf_gige_open+0x5c/0x170 [mlxbf_gige] __dev_open+0x100/0x220 __dev_change_flags+0x16c/0x1f0 dev_change_flags+0x2c/0x70 do_setlink+0x220/0xa40 __rtnl_newlink+0x56c/0x8a0 rtnl_newlink+0x58/0x84 rtnetlink_rcv_msg+0x138/0x3c4 netlink_rcv_skb+0x64/0x130 rtnetlink_rcv+0x20/0x30 netlink_unicast+0x2ec/0x360 netlink_sendmsg+0x278/0x490 __sock_sendmsg+0x5c/0x6c ____sys_sendmsg+0x290/0x2d4 ___sys_sendmsg+0x84/0xd0 __sys_sendmsg+0x70/0xd0 __arm64_sys_sendmsg+0x2c/0x40 invoke_syscall+0x78/0x100 el0_svc_common.constprop.0+0x54/0x184 do_el0_svc+0x30/0xac el0_svc+0x48/0x160 el0t_64_sync_handler+0xa4/0x12c el0t_64_sync+0x1a4/0x1a8 Code: bad PC value ---[ end trace 7d1c3f3bf9d81885 ]--- Kernel panic - not syncing: Oops: Fatal exception in interrupt Kernel Offset: 0x2870a7a00000 from 0xffff800008000000 PHYS_OFFSET: 0x80000000 CPU features: 0x0,000005c1,a3332a5a Memory Limit: none ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]--- The exception happens because there is a pending RX interrupt before the call to request_irq(RX IRQ) executes. Then, the RX IRQ handler fires immediately after this request_irq() completes. The RX IRQ handler runs "napi_schedule()" before NAPI is fully initialized via "netif_napi_add()" and "napi_enable()", both which happen later in the open() logic. The logic in mlxbf_gige_open() must fully initialize NAPI before any calls to request_irq() execute. Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver") Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Link: https://lore.kernel.org/r/20240325183627.7641-1-davthompson@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-26net: amd8111e: Drop unused copy of pm_capBjorn Helgaas
The copy of pdev->pm_cap in struct amd8111e_priv is never used. Drop it. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240325220633.1453180-1-helgaas@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-26i40e: fix vf may be used uninitialized in this function warningAleksandr Loktionov
To fix the regression introduced by commit 52424f974bc5, which causes servers hang in very hard to reproduce conditions with resets races. Using two sources for the information is the root cause. In this function before the fix bumping v didn't mean bumping vf pointer. But the code used this variables interchangeably, so stale vf could point to different/not intended vf. Remove redundant "v" variable and iterate via single VF pointer across whole function instead to guarantee VF pointer validity. Fixes: 52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26i40e: fix i40e_count_filters() to count only active/new filtersAleksandr Loktionov
The bug usually affects untrusted VFs, because they are limited to 18 MACs, it affects them badly, not letting to create MAC all filters. Not stable to reproduce, it happens when VF user creates MAC filters when other MACVLAN operations are happened in parallel. But consequence is that VF can't receive desired traffic. Fix counter to be bumped only for new or active filters. Fixes: 621650cabee5 ("i40e: Refactoring VF MAC filters counting to make more reliable") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26i40e: Enforce software interrupt during busy-poll exitIvan Vecera
As for ice bug fixed by commit b7306b42beaf ("ice: manage interrupts during poll exit") followed by commit 23be7075b318 ("ice: fix software generating extra interrupts") I'm seeing the similar issue also with i40e driver. In certain situation when busy-loop is enabled together with adaptive coalescing, the driver occasionally misses that there are outstanding descriptors to clean when exiting busy poll. Try to catch the remaining work by triggering a software interrupt when exiting busy poll. No extra interrupts will be generated when busy polling is not used. The issue was found when running sockperf ping-pong tcp test with adaptive coalescing and busy poll enabled (50 as value busy_pool and busy_read sysctl knobs) and results in huge latency spikes with more than 100000us. The fix is inspired from the ice driver and do the following: 1) During napi poll exit in case of busy-poll (napo_complete_done() returns false) this is recorded to q_vector that we were in busy loop. 2) Extends i40e_buildreg_itr() to be able to add an enforced software interrupt into built value 2) In i40e_update_enable_itr() enforces a software interrupt trigger if we are exiting busy poll to catch any pending clean-ups 3) Reuses unused 3rd ITR (interrupt throttle) index and set it to 20K interrupts per second to limit the number of these sw interrupts. Test results ============ Prior: [root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120 sockperf: == version #3.10-no.git == sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s) [ 0] IP = 10.9.9.1 PORT = 11111 # TCP sockperf: Warmup stage (sending a few dummy messages)... sockperf: Starting test... sockperf: Test end (interrupted by timer) sockperf: Test ended sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2438563; ReceivedMessages=2438562 sockperf: ========= Printing statistics for Server No: 0 sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2429473; ReceivedMessages=2429473 sockperf: ====> avg-latency=24.571 (std-dev=93.297, mean-ad=4.904, median-ad=1.510, siqr=1.063, cv=3.797, std-error=0.060, 99.0% ci=[24.417, 24.725]) sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0 sockperf: Summary: Latency is 24.571 usec sockperf: Total 2429473 observations; each percentile contains 24294.73 observations sockperf: ---> <MAX> observation = 103294.331 sockperf: ---> percentile 99.999 = 45.633 sockperf: ---> percentile 99.990 = 37.013 sockperf: ---> percentile 99.900 = 35.910 sockperf: ---> percentile 99.000 = 33.390 sockperf: ---> percentile 90.000 = 28.626 sockperf: ---> percentile 75.000 = 27.741 sockperf: ---> percentile 50.000 = 26.743 sockperf: ---> percentile 25.000 = 25.614 sockperf: ---> <MIN> observation = 12.220 After: [root@dell-per640-07 net]# sockperf ping-pong -i 10.9.9.1 --tcp -m 1000 --mps=max -t 120 sockperf: == version #3.10-no.git == sockperf[CLIENT] send on:sockperf: using recvfrom() to block on socket(s) [ 0] IP = 10.9.9.1 PORT = 11111 # TCP sockperf: Warmup stage (sending a few dummy messages)... sockperf: Starting test... sockperf: Test end (interrupted by timer) sockperf: Test ended sockperf: [Total Run] RunTime=119.999 sec; Warm up time=400 msec; SentMessages=2400055; ReceivedMessages=2400054 sockperf: ========= Printing statistics for Server No: 0 sockperf: [Valid Duration] RunTime=119.549 sec; SentMessages=2391186; ReceivedMessages=2391186 sockperf: ====> avg-latency=24.965 (std-dev=5.934, mean-ad=4.642, median-ad=1.485, siqr=1.067, cv=0.238, std-error=0.004, 99.0% ci=[24.955, 24.975]) sockperf: # dropped messages = 0; # duplicated messages = 0; # out-of-order messages = 0 sockperf: Summary: Latency is 24.965 usec sockperf: Total 2391186 observations; each percentile contains 23911.86 observations sockperf: ---> <MAX> observation = 195.841 sockperf: ---> percentile 99.999 = 45.026 sockperf: ---> percentile 99.990 = 39.009 sockperf: ---> percentile 99.900 = 35.922 sockperf: ---> percentile 99.000 = 33.482 sockperf: ---> percentile 90.000 = 28.902 sockperf: ---> percentile 75.000 = 27.821 sockperf: ---> percentile 50.000 = 26.860 sockperf: ---> percentile 25.000 = 25.685 sockperf: ---> <MIN> observation = 12.277 Fixes: 0bcd952feec7 ("ethernet/intel: consolidate NAPI and NAPI exit") Reported-by: Hugo Ferreira <hferreir@redhat.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-26net: hns3: mark unexcuted loopback test result as UNEXECUTEDJian Shen
Currently, loopback test may be skipped when resetting, but the test result will still show as 'PASS', because the driver doesn't set ETH_TEST_FL_FAILED flag. Fix it by setting the flag and initializating the value to UNEXECUTED. Fixes: 4c8dab1c709c ("net: hns3: reconstruct function hns3_self_test") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-26net: hns3: fix kernel crash when devlink reload during pf initializationYonglong Liu
The devlink reload process will access the hardware resources, but the register operation is done before the hardware is initialized. So, processing the devlink reload during initialization may lead to kernel crash. This patch fixes this by taking devl_lock during initialization. Fixes: b741269b2759 ("net: hns3: add support for registering devlink for PF") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-26net: hns3: fix index limit to support all queue statsJie Wang
Currently, hns hardware supports more than 512 queues and the index limit in hclge_comm_tqps_update_stats is wrong. So this patch removes it. Fixes: 287db5c40d15 ("net: hns3: create new set of common tqp stats APIs for PF and VF reuse") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-26net: dsa: mt7530: fix improper frames on all 25MHz and 40MHz XTAL MT7530Arınç ÜNAL
The MT7530 switch after reset initialises with a core clock frequency that works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock frequency must be set to 500MHz. The mt7530_pll_setup() function is responsible of setting the core clock frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This causes MT7530 switch with 25MHz XTAL to egress and ingress frames improperly. Introduce a check to run it only on MT7530 with 40MHz XTAL. The core clock frequency is set by writing to a switch PHY's register. Access to the PHY's register is done via the MDIO bus the switch is also on. Therefore, it works only when the switch makes switch PHYs listen on the MDIO bus the switch is on. This is controlled either by the state of the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the modifiable trap register. When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means accessing PHY registers via the PHY indirect access control register of the switch. When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means accessing PHY registers via the MDIO bus the switch is on. For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high, the core clock frequency won't be set to 500MHz, causing the switch to egress and ingress frames improperly. Run mt7530_pll_setup() after PHY direct access is set on the modifiable trap register. With these two changes, all MT7530 switches with 25MHz and 40MHz, and P1_LED_1 pulled high or low, will egress and ingress frames properly. Link: https://github.com/BPI-SINOVOIP/BPI-R2-bsp/blob/4a5dd143f2172ec97a2872fa29c7c4cd520f45b5/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c#L1039 Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-03-25net: wwan: t7xx: Split 64bit accesses to fix alignment issuesBjørn Mork
Some of the registers are aligned on a 32bit boundary, causing alignment faults on 64bit platforms. Unable to handle kernel paging request at virtual address ffffffc084a1d004 Mem abort info: ESR = 0x0000000096000061 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x21: alignment fault Data abort info: ISV = 0, ISS = 0x00000061, ISS2 = 0x00000000 CM = 0, WnR = 1, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000046ad6000 [ffffffc084a1d004] pgd=100000013ffff003, p4d=100000013ffff003, pud=100000013ffff003, pmd=0068000020a00711 Internal error: Oops: 0000000096000061 [#1] SMP Modules linked in: mtk_t7xx(+) qcserial pppoe ppp_async option nft_fib_inet nf_flow_table_inet mt7921u(O) mt7921s(O) mt7921e(O) mt7921_common(O) iwlmvm(O) iwldvm(O) usb_wwan rndis_host qmi_wwan pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mt7996e(O) mt792x_usb(O) mt792x_lib(O) mt7915e(O) mt76_usb(O) mt76_sdio(O) mt76_connac_lib(O) mt76(O) mac80211(O) iwlwifi(O) huawei_cdc_ncm cfg80211(O) cdc_ncm cdc_ether wwan usbserial usbnet slhc sfp rtc_pcf8563 nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 mt6577_auxadc mdio_i2c libcrc32c compat(O) cdc_wdm cdc_acm at24 crypto_safexcel pwm_fan i2c_gpio i2c_smbus industrialio i2c_algo_bit i2c_mux_reg i2c_mux_pca954x i2c_mux_pca9541 i2c_mux_gpio i2c_mux dummy oid_registry tun sha512_arm64 sha1_ce sha1_generic seqiv md5 geniv des_generic libdes cbc authencesn authenc leds_gpio xhci_plat_hcd xhci_pci xhci_mtk_hcd xhci_hcd nvme nvme_core gpio_button_hotplug(O) dm_mirror dm_region_hash dm_log dm_crypt dm_mod dax usbcore usb_common ptp aquantia pps_core mii tpm encrypted_keys trusted CPU: 3 PID: 5266 Comm: kworker/u9:1 Tainted: G O 6.6.22 #0 Hardware name: Bananapi BPI-R4 (DT) Workqueue: md_hk_wq t7xx_fsm_uninit [mtk_t7xx] pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : t7xx_cldma_hw_set_start_addr+0x1c/0x3c [mtk_t7xx] lr : t7xx_cldma_start+0xac/0x13c [mtk_t7xx] sp : ffffffc085d63d30 x29: ffffffc085d63d30 x28: 0000000000000000 x27: 0000000000000000 x26: 0000000000000000 x25: ffffff80c804f2c0 x24: ffffff80ca196c05 x23: 0000000000000000 x22: ffffff80c814b9b8 x21: ffffff80c814b128 x20: 0000000000000001 x19: ffffff80c814b080 x18: 0000000000000014 x17: 0000000055c9806b x16: 000000007c5296d0 x15: 000000000f6bca68 x14: 00000000dbdbdce4 x13: 000000001aeaf72a x12: 0000000000000001 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : ffffff80ca1ef6b4 x7 : ffffff80c814b818 x6 : 0000000000000018 x5 : 0000000000000870 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 000000010a947000 x1 : ffffffc084a1d004 x0 : ffffffc084a1d004 Call trace: t7xx_cldma_hw_set_start_addr+0x1c/0x3c [mtk_t7xx] t7xx_fsm_uninit+0x578/0x5ec [mtk_t7xx] process_one_work+0x154/0x2a0 worker_thread+0x2ac/0x488 kthread+0xe0/0xec ret_from_fork+0x10/0x20 Code: f9400800 91001000 8b214001 d50332bf (f9000022) ---[ end trace 0000000000000000 ]--- The inclusion of io-64-nonatomic-lo-hi.h indicates that all 64bit accesses can be replaced by pairs of nonatomic 32bit access. Fix alignment by forcing all accesses to be 32bit on 64bit platforms. Link: https://forum.openwrt.org/t/fibocom-fm350-gl-support/142682/72 Fixes: 39d439047f1d ("net: wwan: t7xx: Add control DMA interface") Signed-off-by: Bjørn Mork <bjorn@mork.no> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Tested-by: Liviu Dudau <liviu@dudau.co.uk> Link: https://lore.kernel.org/r/20240322144000.1683822-1-bjorn@mork.no Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-25net: ll_temac: platform_get_resource replaced by wrong functionClaus Hansen Ries
The function platform_get_resource was replaced with devm_platform_ioremap_resource_byname and is called using 0 as name. This eventually ends up in platform_get_resource_byname in the call stack, where it causes a null pointer in strcmp. if (type == resource_type(r) && !strcmp(r->name, name)) It should have been replaced with devm_platform_ioremap_resource. Fixes: bd69058f50d5 ("net: ll_temac: Use devm_platform_ioremap_resource_byname()") Signed-off-by: Claus Hansen Ries <chr@terma.com> Cc: stable@vger.kernel.org Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/cca18f9c630a41c18487729770b492bb@terma.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-26wifi: rtw89: disable txptctrl IMR to avoid flase alarmChia-Yuan Li
The hardware command parser of txptctrl (TX protocol control) has overly stringent timeout conditions, which results in false alarm. So disable it. Signed-off-by: Chia-Yuan Li <leo.li@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://msgid.link/20240321025603.20614-1-pkshih@realtek.com
2024-03-26wifi: rtw88: coex: Prevent doing I/O during Wi-Fi power savingChing-Te Ku
Fix Wi-Fi 2.4Ghz throughput drop over than 40% when Bluetooh is idle. The code flow will read registers during Wi-Fi power saving, and be returned, which results in incorrect counters to do mechanism judgment. Adjust the code flow. Will leave Wi-Fi power save mode first then update counters. Signed-off-by: Ching-Te Ku <ku920601@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://msgid.link/20240320075047.31810-1-pkshih@realtek.com
2024-03-25ice: count representor statsMichal Swiatkowski
Removing control plane VSI result in no information about slow-path statistic. In current solution statistics need to be counted in driver. Patch is based on similar implementation done by Simon Horman in nfp: commit eadfa4c3be99 ("nfp: add stats and xmit helpers for representors") Add const modifier to netdev parameter in ice_netdev_to_repr(). It isn't (and shouldn't be) modified in the function. Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: do switchdev slow-path Rx using PF VSIMichal Swiatkowski
Add an ICE_RX_FLAG_MULTIDEV flag to Rx ring. If it is set try to find correct port representor. Do it based on src_vsi value stored in flex descriptor. Ids of representor pointers stored in xarray are equal to corresponding src_vsi value. Thanks to that we can directly get correct representor if we have src_vsi value. Set multidev flag during ring configuration. If the mode is switchdev, change the ring descriptor to the one that contains src_vsi value. PF netdev should be reconfigured, do it by calling ice_down() and ice_up() if the netdev was up before configuring switchdev. Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: change repr::id valuesMichal Swiatkowski
Instead of getting repr::id from xa_alloc() value, set it to the src_vsi::num_vsi value. It is unique for each PR. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: remove switchdev control plane VSIMichal Swiatkowski
For slow-path Rx and Tx PF VSI is used. There is no need to have control plane VSI. Remove all code related to it. Eswitch rebuild can't fail without rebuilding control plane VSI. Return void from ice_eswitch_rebuild(). Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-03-25ice: control default Tx rule in lagMichal Swiatkowski
Tx rule in switchdev was changed to use PF instead of additional control plane VSI. Because of that during lag we should control it. Control means to add and remove the default Tx rule during lag active/inactive switching. It can be done the same way as default Rx rule. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2026-09-01 11:22:47 +0000