| Age | Commit message (Collapse) | Author |
|---|
|
There is a new register used to configure selective update area size
for early transport.
Configure PIPE_SRCSZ_ERLY_TPT using calculated selective update area
carried in crtc_state->su_area.
Bspec: 68927
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218175004.52875-6-jouni.hogander@intel.com
|
|
New register CUR_POS_ERLY_TPT related to early transport is
supposed to be configured when early transport is in use.
This register is used to configure cursor vertical postion
from beginning of selective update area.
Bspec: 68927
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218175004.52875-5-jouni.hogander@intel.com
|
|
Su_area is needed when configuring CUR_POS_ERLY_TPT and
PIPE_SRC_SZ_ERLY_TPT. Store it into intel_crtc_state->psr2_su_area.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218175004.52875-4-jouni.hogander@intel.com
|
|
In case early transport is enabled SU area needs to be extended
to cover cursor area fully when cursor is in SU area.
Bspec: 68927
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218175004.52875-3-jouni.hogander@intel.com
|
|
The initialization commands are taken from the STMicroelectronics driver
found at [1].
To ensure backward compatibility, flags have been added to enable gamma
correction setting and display control. In other cases, registers have
been set to their default values according to the specifications found
in the datasheet.
[1] https://github.com/STMicroelectronics/STM32CubeF7/blob/master/Drivers/BSP/Components/nt35510/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240108201618.2798649-9-dario.binacchi@amarulasolutions.com
|
|
This patch, preparatory for future developments, move the hardwired
parameters to configuration data to allow the addition of new
NT35510-based panels.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240108201618.2798649-8-dario.binacchi@amarulasolutions.com
|
|
Use correct helper for getting max DSC bpc supported by the source.
Fixes: 1c56e9a39833 ("drm/i915/dp: Get optimal link config to have best compressed bpp")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213091632.431557-3-ankit.k.nautiyal@intel.com
|
|
commit 23baf831a32c ("mm, treewide: redefine MAX_ORDER sanely") has
changed the definition of MAX_ORDER to be inclusive. This has caused
issues with code that was not yet upstream and depended on the previous
definition.
To draw attention to the altered meaning of the define, rename MAX_ORDER
to MAX_PAGE_ORDER.
Link: https://lkml.kernel.org/r/20231228144704.14033-2-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
NR_PAGE_ORDERS defines the number of page orders supported by the page
allocator, ranging from 0 to MAX_ORDER, MAX_ORDER + 1 in total.
NR_PAGE_ORDERS assists in defining arrays of page orders and allows for
more natural iteration over them.
[kirill.shutemov@linux.intel.com: fixup for kerneldoc warning]
Link: https://lkml.kernel.org/r/20240101111512.7empzyifq7kxtzk3@box
Link: https://lkml.kernel.org/r/20231228144704.14033-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.8-2024-01-05:
amdgpu:
- VRR fixes
- PSR-SU fixes
- SubVP fixes
- DCN 3.5 fixes
- Documentation updates
- DMCUB fixes
- DML2 fixes
- UMC 12.0 updates
- GPUVM fix
- Misc code cleanups and whitespace cleanups
- DP MST fix
- Let KFD sync with GPUVM fences
- GFX11 reset fix
- SMU 13.0.6 fixes
- VSC fix for DP/eDP
- Navi12 display fix
- RN/CZN system aperture fix
- DCN 2.1 bandwidth validation fix
- DCN INIT cleanup
amdkfd:
- SVM fixes
- Revert TBA/TMA location change
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105220522.4976-1-alexander.deucher@amd.com
|
|
Unlike what is claimed in commit f5aa7d46b0ee ("drm/bridge:
parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux"), if
someone manually tries to do an AUX transfer (like via `i2cdump ${bus}
0x50 i`) while the panel is off we don't just get a simple transfer
error. Instead, the whole ps8640 gets thrown for a loop and goes into
a bad state.
Let's put the function to wait for the HPD (and the magical 50 ms
after first reset) back in when we're doing an AUX transfer. This
shouldn't actually make things much slower (assuming the panel is on)
because we should immediately poll and see the HPD high. Mostly this
is just an extra i2c transfer to the bridge.
Fixes: f5aa7d46b0ee ("drm/bridge: parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux")
Tested-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231221135548.1.I10f326a9305d57ad32cee7f8d9c60518c8be20fb@changeid
|
|
Release all mmap mappings for all vram objects which are associated
with userfault such that, while pcie function in D3hot, any access
to memory mappings will raise a userfault.
Upon userfault, in order to access memory mappings, if graphics
function is in D3 then runtime resume of dgpu will be triggered to
transition to D0.
v2:
- Avoid iomem check before bo migration check as bo can migrate
to system memory (Matthew Auld)
v3:
- Delete bo userfault link during bo destroy
- Upon bo move (vram-smem), do bo userfault link deletion in
xe_bo_move_notify instead of xe_bo_move (Thomas Hellström)
- Grab lock in rpm hook while deleting bo userfault link (Matthew Auld)
v4:
- Add kernel doc and wrap vram_userfault related
stuff in the structure (Matthew Auld)
- Get rpm wakeref before taking dma reserve lock (Matthew Auld)
- In suspend path apply lock for entire list op
including list iteration (Matthew Auld)
v5:
- Use mutex lock instead of spin lock
v6:
- Fix review comments (Matthew Auld)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Badal Nilawar <badal.nilawar@intel.com>
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #For the xe_bo_move_notify() changes
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://lore.kernel.org/r/20240104130702.950078-1-badal.nilawar@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Some edp panel requires T10 (Delay from end of valid video data transmitted
by the Source device to power-off) less than 500ms. Using autosuspend with
delay set as 1000 violates this requirement.
Use put_sync_suspend in unprepare to meet the spec. For other cases (such
as getting EDID), it still uses autosuspend.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Fixes: 3235b0f20a0a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220221418.2610185-1-hsinyi@chromium.org
|
|
Recommendation is to read FUSE4 register to check if WMTP has been
enabled/disabled by HW. If enabled we don't need to do anything special,
however if disabled recommendation is to also disable the WMTP mode in
the FF_SLICE_CS_CHICKEN2 register, falling back to thread-group and
mid-batch preemption only. However on Linux, the per-context CS_CHICKEN1
is how userspace controls pre-emption, so instead use the default lrc to
disable WMTP using CS_CHICKEN1, if disabled by HW. Userspace is still
free to set CS_CHICKEN1 to whatever they want later.
v2: remove redundant version check and also add descriptive name(Matt)
v3: remove usage of REG_FIELD_GET(Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Co-developed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20240104182615.21327-1-nirmoy.das@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
|
|
The function bxt_cdclk_ctl() is responsible for deriving the value for
CDCLK_CTL; use it instead of repeating the same logic.
v2:
- Use a better commit message body by making it more self-contained
and not referring to stuff from the subject line. (Matt)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105140538.183553-5-gustavo.sousa@intel.com
|
|
Make the sequence of steps in bxt_sanitize_cdclk() more logical by
grouping things related to the check on the value of CDCLK_CTL into a
single "block". Also, this will make an upcoming change replacing that
block with a single function call easier to follow.
v2:
- Improve body of commit message to be more self-contained.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105140538.183553-4-gustavo.sousa@intel.com
|
|
Extract logic for deriving the value for CDCLK_CTL into bxt_cdclk_ctl().
This makes the code better readable and will be used later in
bxt_sanitize_cdclk().
v2:
- Improve body of commit message to be more self-contained.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105140538.183553-3-gustavo.sousa@intel.com
|
|
With Xe2_LPD, there were changes to the way CDCLK_CTL must be
programmed. Those were reflected on _bxt_set_cdclk() with commit
3d3696c0fed1 ("drm/i915/lnl: Start using CDCLK through PLL"), but
bxt_sanitize_cdclk() was left out.
This was causing some issues when loading the driver with a pre-existing
active display configuration: the driver would mistakenly take the
current value of CDCLK_CTL as wrong and the sanitization would be
triggered.
In a scenario where the display was already configured with a high
CDCLKC and had plane(s) enabled, FIFO underrun errors were reported,
because the current sanitization code selects the minimum possible
CDCLK.
Fix that by updating bxt_sanitize_cdclk() to match the changes made in
_bxt_set_cdclk(). Ideally, we would have a common function to derive the
value for CDCLK_CTL, but that can be done in a future change.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105140538.183553-2-gustavo.sousa@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull misc vfs updates from Christian Brauner:
"This contains the usual miscellaneous features, cleanups, and fixes
for vfs and individual fses.
Features:
- Add Jan Kara as VFS reviewer
- Show correct device and inode numbers in proc/<pid>/maps for vma
files on stacked filesystems. This is now easily doable thanks to
the backing file work from the last cycles. This comes with
selftests
Cleanups:
- Remove a redundant might_sleep() from wait_on_inode()
- Initialize pointer with NULL, not 0
- Clarify comment on access_override_creds()
- Rework and simplify eventfd_signal() and eventfd_signal_mask()
helpers
- Process aio completions in batches to avoid needless wakeups
- Completely decouple struct mnt_idmap from namespaces. We now only
keep the actual idmapping around and don't stash references to
namespaces
- Reformat maintainer entries to indicate that a given subsystem
belongs to fs/
- Simplify fput() for files that were never opened
- Get rid of various pointless file helpers
- Rename various file helpers
- Rename struct file members after SLAB_TYPESAFE_BY_RCU switch from
last cycle
- Make relatime_need_update() return bool
- Use GFP_KERNEL instead of GFP_USER when allocating superblocks
- Replace deprecated ida_simple_*() calls with their current ida_*()
counterparts
Fixes:
- Fix comments on user namespace id mapping helpers. They aren't
kernel doc comments so they shouldn't be using /**
- s/Retuns/Returns/g in various places
- Add missing parameter documentation on can_move_mount_beneath()
- Rename i_mapping->private_data to i_mapping->i_private_data
- Fix a false-positive lockdep warning in pipe_write() for watch
queues
- Improve __fget_files_rcu() code generation to improve performance
- Only notify writer that pipe resizing has finished after setting
pipe->max_usage otherwise writers are never notified that the pipe
has been resized and hang
- Fix some kernel docs in hfsplus
- s/passs/pass/g in various places
- Fix kernel docs in ntfs
- Fix kcalloc() arguments order reported by gcc 14
- Fix uninitialized value in reiserfs"
* tag 'vfs-6.8.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (36 commits)
reiserfs: fix uninit-value in comp_keys
watch_queue: fix kcalloc() arguments order
ntfs: dir.c: fix kernel-doc function parameter warnings
fs: fix doc comment typo fs tree wide
selftests/overlayfs: verify device and inode numbers in /proc/pid/maps
fs/proc: show correct device and inode numbers in /proc/pid/maps
eventfd: Remove usage of the deprecated ida_simple_xx() API
fs: super: use GFP_KERNEL instead of GFP_USER for super block allocation
fs/hfsplus: wrapper.c: fix kernel-doc warnings
fs: add Jan Kara as reviewer
fs/inode: Make relatime_need_update return bool
pipe: wakeup wr_wait after setting max_usage
file: remove __receive_fd()
file: stop exposing receive_fd_user()
fs: replace f_rcuhead with f_task_work
file: remove pointless wrapper
file: s/close_fd_get_file()/file_close_fd()/g
Improve __fget_files_rcu() code generation (and thus __fget_light())
file: massage cleanup of files that failed to open
fs/pipe: Fix lockdep false-positive in watchqueue pipe_write()
...
|
|
As workarounds for pre-production DG2 were dropped in
commit 707d1b992cfe ("drm/xe/dg2: Drop pre-production workarounds"),
there's no point running the kunit tests for them. Drop
those steppings from kunit.
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20231221163213.3849523-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Change kernel-doc "/**" comments to common "/*" comments to prevent
kernel-doc warnings:
gk20a.c:49: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* cvb_mv = ((c2 * speedo / s_scale + c1) * speedo / s_scale + c0)
gk20a.c:49: warning: missing initial short description on line:
* cvb_mv = ((c2 * speedo / s_scale + c1) * speedo / s_scale + c0)
gk20a.c:62: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* cvb_t_mv =
gk20a.c:62: warning: missing initial short description on line:
* cvb_t_mv =
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231231233633.6596-4-rdunlap@infradead.org
|
|
Change kernel-doc "/**" comments to common "/*" comments to prevent
kernel-doc warnings:
gf100.c:1044: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Wait until GR goes idle. GR is considered idle if it is disabled by the
gf100.c:1044: warning: missing initial short description on line:
* Wait until GR goes idle. GR is considered idle if it is disabled by the
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231231233633.6596-3-rdunlap@infradead.org
|
|
Change kernel-doc "/**" comments to common "/*" comments to prevent
kernel-doc warnings:
nouveau_ioc32.c:2: warning: Cannot understand * \file mga_ioc32.c
on line 2 - I thought it was a doc line
nouveau_ioc32.c:52: warning: Function parameter or member 'filp' not described in 'nouveau_compat_ioctl'
nouveau_ioc32.c:52: warning: Function parameter or member 'cmd' not described in 'nouveau_compat_ioctl'
nouveau_ioc32.c:52: warning: Function parameter or member 'arg' not described in 'nouveau_compat_ioctl'
nouveau_ioc32.c:52: warning: expecting prototype for Called whenever a 32-bit process running under a 64(). Prototype was for nouveau_compat_ioctl() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231231233633.6596-2-rdunlap@infradead.org
|
|
Change kernel-doc "/**" comments to common "/*" comments to prevent
kernel-doc warnings:
crtc.c:453: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Sets up registers for the given mode/adjusted_mode pair.
crtc.c:453: warning: missing initial short description on line:
* Sets up registers for the given mode/adjusted_mode pair.
crtc.c:629: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Sets up registers for the given mode/adjusted_mode pair.
crtc.c:629: warning: missing initial short description on line:
* Sets up registers for the given mode/adjusted_mode pair.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231231233633.6596-1-rdunlap@infradead.org
|
|
The "/**" comments in this file are not kernel-doc comments. They are
used on static functions which can have kernel-doc comments, but that
is not the primary focus of kernel-doc comments.
Since these comments are incomplete for kernel-doc notation, remove
the kernel-doc "/**" markers and make them common comments.
This prevents scripts/kernel-doc from issuing 68 warnings:
init.c:584: warning: Function parameter or member 'init' not described in 'init_reserved'
and 67 warnings like this one:
init.c:611: warning: expecting prototype for INIT_DONE(). Prototype was for init_done() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231216201152.31376-1-rdunlap@infradead.org
|
|
An AUX transfer on any disconnected DP port results in long
timeout/retry delays the same way as this is described for TypeC port in
commit a972cd3f0eb5 ("drm/i915/tc: Abort DP AUX transfer on a disconnected TC port")
Prevent the delay on non-TypeC ports as well by aborting the transfer if
the port is disconnected. For eDP keep the current behavior as the
support for HPD signaling is optional for it.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-13-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
Glitches deasserting the connector HPD line can lead to incorrectly
detecting a disconnect event (a glitch asserting the line will only
cause a redundant connect->disconnect transition). The source of such a
glitch can be noise on the line or a 0.5ms-1ms MST IRQ_HPD pulse. TypeC
ports in the DP-alt or TBT-alt mode filter out these glitches inernally,
but for others the driver has to do this. Make it so by polling the HPD
line on these connectors for 4 ms.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-12-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
Add hooks to intel_digital_port to lock and unlock the port and add a
helper to check the connector's detect status while the port is locked
already. This simplifies checking the connector detect status in
intel_dp_aux_xfer() and intel_digital_port_connected() in the next two
patches aborting AUX transfers on all DP connectors (except eDP) and
filtering HPD glitches.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-11-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
As described in the previous two patches an unexpected connector
detection can happen during the init/shutdown sequences. Prevent these
by returning the connector's current status from the detection handlers.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-10-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
As described in the previous patch, an unexpected connector
detection/modeset started from the intel_hotplug::hotplug_work can
happen during the driver init/shutdown sequence. Prevent these by
disabling the queuing of and flushing all the intel_hotplug work that
can start them at the beginning of the init/shutdown sequence and allow
the queuing only while the display is in the initialized state.
Other work items - like the intel_connector::modeset_retry_work or the
MST probe works - are still enabled and can start a detection/modeset,
but after the previous patch these will be rejected. Disabling these
works as well is for a follow-up patchset.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-9-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
An unexpected modeset or connector detection by a user (user space or FB
console) during the initialization/shutdown sequence is possible either
via a hotplug IRQ handling work or via the connector sysfs
(status/detect) interface. These modesets/detections should be prevented
by disabling/flushing all related hotplug handling work and
unregistering the interfaces that can start them at the beginning of the
shutdown sequence. Some of this - disabling all related intel_hotplug
work - will be done by the next patch, but others - for instance
disabling the MST hotplug works - require a bigger rework.
It makes sense - for diagnostic purpose, even with all the above work and
interface disabled - to detect and reject any such user access. This
patch does that for modeset accesses and a follow-up patch for connector
detection.
During driver loading/unloading/system suspend/shutdown and during
system resume after calling intel_display_driver_disable_user_access()
or intel_display_driver_resume_access() correspondigly, the current
thread is allowed to modeset (as this thread requires to do an
initial/restoring modeset or a disabling modeset), other threads (the
user threads) are not allowed to modeset.
During driver loading/system resume after calling
intel_display_driver_enable_user_access() all threads are allowed to
modeset.
During driver unloading/system suspend/shutdown after calling
intel_display_driver_suspend_access() no threads are allowed to modeset
(as the HW got disabled and should stay in this state).
v2: Call intel_display_driver_suspend_access()/resume_access() only
for HAS_DISPLAY(). (CI)
v3: (Jouni)
- Add commit log comments explaining how the permission of modeset
changes during HW init/deinit wrt. to the current and other user
processes.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104132335.2766434-1-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
Suspend the FB console early during system suspend to prevent new FB
probe/modeset cycles interfering with the HW uninitialization steps in a
similar way as during driver shutdown as described in the previous
patch.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-7-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
Suspend the FB console during driver shutdown the same way this is done
during system resume. This should prevent any HPD event to trigger a new
FB probe/modeset cycle happening in parallel with the display HW
disable/uninitialize steps.
A preceding FB HPD event handling may be still pending, resulting in a
probe/modeset like the above, these will be prevented by a later change
in this patchset.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-6-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
The only purpose of intel_hpd_poll_disable() during driver loading and
system resume - at which point polling should be disabled anyway, except
for connectors in an IRQ storm, for which the polling will stay enabled -
is to force-detect all the connectors. However this detection in
i915_hpd_poll_init_work() depends on drm.mode_config.poll_enabled, which
will get set in drm_kms_helper_poll_init(), possibly after
i915_hpd_poll_init_work() is scheduled. Hence the initial detection of
connectors during driver loading may not happen.
Fix the above by moving intel_hpd_poll_disable() after
i915_hpd_poll_init_work(), the proper place anyway for doing the above
detection after all the HW initialization steps are complete. Change the
order the same way during system resume as well. The above race
condition shouldn't matter here - as drm.mode_config.poll_enabled will
be set - but the detection should happen here as well after the HW init
steps are done.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-5-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
Deinitialize audio during driver unload after disabling polling. This is
in preparation to do all the display HW init/deinit steps at a point
where no HPD IRQ or polling initiated connector detection or modeset can
change the HW state. This may still happen here via an HPD IRQ ->
hotplug detection work or a connector sysfs (state/detect) access, but
these will be prevented by later changes in this patchset.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-4-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
If an HPD IRQ storm is detected on a connector during driver loading or
system suspend/resume - disabling the IRQ and switching to polling - the
polling may get disabled too early - before the intended 2 minute
HPD_STORM_REENABLE_DELAY - with the HPD IRQ staying disabled for this
duration. One such sequence is:
Thread#1 Thread#2
intel_display_driver_probe()->
intel_hpd_init()->
(HPD IRQ gets enabled)
. intel_hpd_irq_handler()->
. intel_hpd_irq_storm_detect()
. intel_hpd_irq_setup()->
. (HPD IRQ gets disabled)
. queue_delayed_work(hotplug.hotplug_work)
. ...
. i915_hotplug_work_func()->
. intel_hpd_irq_storm_switch_to_polling()->
. (polling enabled)
.
intel_hpd_poll_disable()->
queue_work(hotplug.poll_init_work)
...
i915_hpd_poll_init_work()->
(polling gets disabled,
HPD IRQ is still disabled)
...
(Connector is neither polled or
detected via HPD IRQs for 2 minutes)
intel_hpd_irq_storm_reenable_work()->
(HPD IRQ gets enabled)
To avoid the above 2 minute state without either polling or enabled HPD
IRQ, leave the connector's polling mode unchanged in
i915_hpd_poll_init_work() if its HPD IRQ got disabled after an IRQ storm
indicated by the connector's HPD_DISABLED pin state.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-3-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
After an HPD IRQ storm on a connector intel_hpd_irq_storm_detect() will
set the connector's HPD pin state to HPD_MARK_DISABLED and the IRQ gets
disabled. Subsequently intel_hpd_irq_storm_switch_to_polling() will
enable polling for these connectors, setting the pin state to
HPD_DISABLED, but only if the connector's base.polled field is set to
DRM_CONNECTOR_POLL_HPD. intel_hpd_irq_storm_reenable_work() will
reenable the IRQ - after 2 minutes - if the pin state is HPD_DISABLED.
The connectors will be created with their base.polled field set to 0,
which gets initialized only later in i915_hpd_poll_init_work() (using
intel_connector::polled). If a storm is detected on a connector after
it's created and IRQs are enabled on it - by intel_hpd_init() - and
before its bease.polled field is initialized in the above work, the
connector's HPD pin will stay in the HPD_MARK_DISABLED state - leaving
the IRQ disabled indefinitely - and polling will not get enabled on it as
intended.
I can't see a reason for initializing base.polled in a delayed manner,
so do this already when creating the connector, to prevent the above
race condition.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-2-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
|
|
There is a spelling mistake in a drm_info message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20240102092014.3347566-1-colin.i.king@gmail.com
|
|
Remove the unused drm_connector_helper_get_modes_from_ddc()
function. Most drivers should probably have this functionality split to
detect and get modes parts, so the helper is not the best abstraction.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/60eb6b2db16747d3f9c12604b197f33da585c16e.1704473654.git.jani.nikula@intel.com
|
|
Convert mgag200_vga_connector_helper_get_modes() to use struct drm_edid
based functions directly.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/19a453c725fc27bd890f8fc73104f43a376dfce0.1704473654.git.jani.nikula@intel.com
|
|
I/O video memory for the framebuffer supports write-combine caching
mode. Simplify the driver's code that sets up the caching mode.
* Map video memory with ioremap_wc(), which automatically sets up
the PAT entry with write-combine caching.
* Remove the now obsolete call to devm_arch_io_reserve_memtype_wc().
It is only required to mmap the video memory to user space, which the
driver doesn't do.
* According to the PAT documentation, arch_phys_wc_add() is best
called after remapping I/O memory, so move it after ioremap.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105082714.21881-1-tzimmermann@suse.de
|
|
We used to select between MPLLA/B with the following
state->tx[0] & C20_PHY_USE_MPLLB
Since this is used a few places within C20 PLL setting,
let's introduce a helper function to clean up the code
a bit.
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105112243.224199-1-mika.kahola@intel.com
|
|
Return an error code without storing it in an intermediate variable.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/85f8004e-f0c9-42d9-8c59-30f1b4e0b89e@web.de
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
|
|
The kfree() function was called in one case by the
drm_sched_init() function during error handling
even if the passed data structure member contained a null pointer.
This issue was detected by using the Coccinelle software.
Thus adjust a jump target.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/85066512-983d-480c-a44d-32405ab1b80e@web.de
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
|
|
A failure to load the HuC is occasionally observed where the cause is
believed to be a low GT frequency leading to very long load times.
So a) increase the timeout so that the user still gets a working
system even in the case of slow load. And b) report the frequency
during the load to see if that is the cause of the slow down.
Also update the similar code on the GuC load to not use uncore->gt
when there is a local gt available. The two should match, but no need
for unnecessary de-referencing.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240102222202.310495-1-John.C.Harrison@Intel.com
|
|
Copy StutterPeriod from DML2 into DML1 StutterPeriod parameter.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
IGT `amdgpu/amd_color/crtc-lut-accuracy` fails right at the beginning of
the test execution, during atomic check, because DC rejects the
bandwidth state for a fb sizing 64x64. The test was previously working
with the deprecated dc_commit_state(). Now using
dc_validate_with_context() approach, the atomic check needs to perform a
full state validation. Therefore, set fast_validation to false in the
dc_validate_global_state call for atomic check.
Cc: stable@vger.kernel.org
Fixes: b8272241ff9d ("drm/amd/display: Drop dc_commit_state in favor of dc_commit_streams")
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These chips needs the same fix. This was previously not seen
on then since the AGP aperture expanded the system aperture,
but this showed up again when AGP was disabled.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Other environments don't like the unary minus operator on
an unsigned value.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Use tabs, not spaces.
- Brace and parentheses placement
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
