| Age | Commit message (Collapse) | Author |
|---|
|
When oops_panic_write is set, the driver disables interrupts and
switches to PIO polling mode but still falls through into the DMA
path. DMA cannot be used reliably in panic context, so make the
DMA path an else branch to ensure only PIO is used during panic
writes.
Fixes: c1ac2dc34b51 ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
nand_lock() and nand_unlock() call into chip->ops.lock_area/unlock_area
without holding the NAND device lock. On controllers that implement
SET_FEATURES via multiple low-level PIO commands, these can race with
concurrent UBI/UBIFS background erase/write operations that hold the
device lock, resulting in cmd_pending conflicts on the NAND controller.
Add nand_get_device()/nand_release_device() around the lock/unlock
operations to serialize them against all other NAND controller access.
Fixes: 92270086b7e5 ("mtd: rawnand: Add support for manufacturer specific lock/unlock operation")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some bootloaders like recent versions of U-Boot may install some DMI
properties with empty values rather than not populate them. This manages
to make its way through the validator and cleanup resulting in a rogue
hyphen being appended to the card longname.
Fixes: 4e01e5dbba96 ("ASoC: improve the DMI long card code in asoc-core")
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20260306174707.283071-2-casey.connolly@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Example is wrong, the reg property of the flash is always matching the
node name.
Fixes: 68cd8ef48452 ("dt-bindings: mtd: st,spear600-smi: convert to DT schema")
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
These properties must be set because they overwrite the default values,
especially #size-cells which is 0 for most controllers and is 'const: 1'
here.
Fixes: 68cd8ef48452 ("dt-bindings: mtd: st,spear600-smi: convert to DT schema")
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The description mixes two nodes. There is the controller, and there is
the flash. Describe the flash (which itself can be considered an mtd
device, unlike the top level controller), and move the st,smi-fast-mode
property inside, as this property is flash specific and should not live
in the parent controller node.
Fixes: 68cd8ef48452 ("dt-bindings: mtd: st,spear600-smi: convert to DT schema")
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Enable the Qualcomm WCD937x headphone audio codec as a loadable module,
as it is now required on the QCM6490 IDP platform.
Signed-off-by: Ajay Kumar Nandam <ajay.nandam@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260121102606.1753970-1-ajay.nandam@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The DmaGspMem pointer accessor methods (gsp_write_ptr, gsp_read_ptr,
cpu_read_ptr, cpu_write_ptr, advance_cpu_read_ptr,
advance_cpu_write_ptr) dereference a raw pointer to DMA memory, creating
an intermediate reference before calling volatile read/write methods.
This is undefined behavior since DMA memory can be concurrently modified
by the device.
Fix this by moving the implementations into a gsp_mem module in fw.rs
that uses the dma_read!() / dma_write!() macros, making the original
methods on DmaGspMem thin forwarding wrappers.
An alternative approach would have been to wrap the shared memory in
Opaque, but that would have required even more unsafe code.
Since the gsp_mem module lives in fw.rs (to access firmware-specific
binding field names), GspMem, Msgq and their relevant fields are
temporarily widened to pub(super). This will be reverted once IoView
projections are available.
Cc: Gary Guo <gary@garyguo.net>
Closes: https://lore.kernel.org/nouveau/DGUT14ILG35P.1UMNRKU93JUM1@kernel.org/
Fixes: 75f6b1de8133 ("gpu: nova-core: gsp: Add GSP command queue bindings and handling")
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Link: https://patch.msgid.link/20260309225408.27714-1-dakr@kernel.org
[ Use pub(super) where possible; replace bitwise-and with modulo
operator analogous to [1]. - Danilo ]
Link: https://lore.kernel.org/all/20260129-nova-core-cmdq1-v3-1-2ede85493a27@nvidia.com/ [1]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
All Qualcomm SoCs starting from SM8650 provide access to the Qualcomm
Trusted Execution Environment (QTEE) through the SMCInvoke interface,
implemented by the QCOMTEE driver. QTEE runs in the Secure World domain
on ARM64 CPUs and exposes secure services to Linux running in the Normal
World domain.
This change enables the QCOMTEE driver as a module to support
communication with QTEE.
QCOMTEE has been tested on a Qualcomm RB3Gen2 board by loading and
executing a Trusted Application via tests hosted at
github.com/qualcomm/minkipc.
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Tested-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260114-qcom_qcomtee_defconfig-v4-1-ec676311171f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
In docg3_release(), the docg3 pointer is obtained from
cascade->floors[0]->priv before the loop that calls
doc_release_device() on each floor. doc_release_device() frees the
docg3 struct via kfree(docg3) at line 1881. After the loop,
docg3->cascade->bch dereferences the already-freed pointer.
Fix this by accessing cascade->bch directly, which is equivalent
since docg3->cascade points back to the same cascade struct, and
is already available as a local variable. This also removes the
now-unused docg3 local variable.
Fixes: c8ae3f744ddc ("lib/bch: Rework a little bit the exported function names")
Cc: stable@vger.kernel.org
Signed-off-by: James Kim <james010kim@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
A flex array can be used to reduce the allocation to 1.
And actually mtdconcat was using the pointer + 1 trick to point to the
overallocated area. Better alternatives exist.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Simpler to reason about and avoids having to free nodes separately.
Also add __counted_by attribute for extra runtime analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The function name in the kdoc comment is different from the name of the
function being documented, fix it.
Fixes: 43db6366fc2d ("mtd: Add driver for concatenating devices")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202603041232.fNDHNtUa-lkp@intel.com/
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The LPVO USB GPIB adapter apparently uses an FTDI 8U232AM with the
default PID, but this device id is already handled by the ftdi_sio
serial driver.
Stop binding to the default PID to avoid breaking existing setups with
FTDI 8U232AM.
Anyone using this driver should blacklist the ftdi_sio driver and add
the device id manually through sysfs (e.g. using udev rules).
Fixes: fce79512a96a ("staging: gpib: Add LPVO DIY USB GPIB driver")
Fixes: e6ab504633e4 ("staging: gpib: Destage gpib")
Cc: Dave Penkler <dpenkler@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260305151729.10501-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_role_switch_is_parent() was walking up to the parent node and checking
for the "usb-role-switch" property regardless of the type of the passed
fwnode. This could cause unrelated device nodes to be probed as potential
role switch parent, leading to spurious matches and "-EPROBE_DEFER" being
returned infinitely.
Till now only Type-B connector node will have a parent node which may
present "usb-role-switch" property and register the role switch device.
For Type-C connector node, its parent node will always be a Type-C chip
device which will never register the role switch device. However, it may
still present a non-boolean "usb-role-switch = <&usb_controller>" property
for historical compatibility.
So restrict the helper to only operate on Type-B connector when attempting
to get the role switch from parent node.
Fixes: 6fadd72943b8 ("usb: roles: get usb-role-switch from parent")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Tested-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260309074313.2809867-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1366cd228b0c67b60a2c0c26ef37fe9f7cfedb7f.
The fwnode_usb_role_switch_get() returns NULL only if no connection is
found, returns ERR_PTR(-EPROBE_DEFER) if connection is found but deferred
probe is needed, or a valid pointer of usb_role_switch.
When switching from a NULL check to IS_ERR_OR_NULL(), usb_role_switch_get()
returns NULL and overwrites the ERR_PTR(-EPROBE_DEFER) returned by
fwnode_usb_role_switch_get(). This causes the deferred probe indication to
be lost, preventing the USB role switch from ever being retrieved.
Fixes: 1366cd228b0c ("tcpm: allow looking for role_sw device in the main node")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Tested-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260309074313.2809867-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The network device outlived its parent gadget device during
disconnection, resulting in dangling sysfs links and null pointer
dereference problems.
A prior attempt to solve this by removing SET_NETDEV_DEV entirely [1]
was reverted due to power management ordering concerns and a NO-CARRIER
regression.
A subsequent attempt to defer net_device allocation to bind [2] broke
1:1 mapping between function instance and network device, making it
impossible for configfs to report the resolved interface name. This
results in a regression where the DHCP server fails on pmOS.
Use device_move to reparent the net_device between the gadget device and
/sys/devices/virtual/ across bind/unbind cycles. This preserves the
network interface across USB reconnection, allowing the DHCP server to
retain their binding.
Introduce gether_attach_gadget()/gether_detach_gadget() helpers and use
__free(detach_gadget) macro to undo attachment on bind failure. The
bind_count ensures device_move executes only on the first bind.
[1] https://lore.kernel.org/lkml/f2a4f9847617a0929d62025748384092e5f35cce.camel@crapouillou.net/
[2] https://lore.kernel.org/linux-usb/795ea759-7eaf-4f78-81f4-01ffbf2d7961@ixit.cz/
Fixes: 40d133d7f542 ("usb: gadget: f_ncm: convert to new function interface with backward compatibility")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-7-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit e065c6a7e46c2ee9c677fdbf50035323d2de1215.
This commit is being reverted as part of a series-wide revert.
By deferring the net_device allocation to the bind() phase, a single
function instance will spawn multiple network devices if it is symlinked
to multiple USB configurations.
This causes regressions for userspace tools (like the postmarketOS DHCP
daemon) that rely on reading the interface name (e.g., "usb0") from
configfs. Currently, configfs returns the template "usb%d", causing the
userspace network setup to fail.
Crucially, because this patch breaks the 1:1 mapping between the
function instance and the network device, this naming issue cannot
simply be patched. Configfs only exposes a single 'ifname' attribute per
instance, making it impossible to accurately report the actual interface
name when multiple underlying network devices can exist for that single
instance.
All configurations tied to the same function instance are meant to share
a single network device. Revert this change to restore the 1:1 mapping
by allocating the network device at the instance level (alloc_inst).
Reported-by: David Heidelberg <david@ixit.cz>
Closes: https://lore.kernel.org/linux-usb/70b558ea-a12e-4170-9b8e-c951131249af@ixit.cz/
Fixes: 56a512a9b410 ("usb: gadget: f_ncm: align net_device lifecycle with bind/unbind")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-6-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 7a7930c0f934fb0c46de6e7ca08e14e11df35dd6.
This commit is being reverted as part of a series-wide revert.
By deferring the net_device allocation to the bind() phase, a single
function instance will spawn multiple network devices if it is symlinked
to multiple USB configurations.
This causes regressions for userspace tools (like the postmarketOS DHCP
daemon) that rely on reading the interface name (e.g., "usb0") from
configfs. Currently, configfs returns the template "usb%d", causing the
userspace network setup to fail.
Crucially, because this patch breaks the 1:1 mapping between the
function instance and the network device, this naming issue cannot
simply be patched. Configfs only exposes a single 'ifname' attribute per
instance, making it impossible to accurately report the actual interface
name when multiple underlying network devices can exist for that single
instance.
All configurations tied to the same function instance are meant to share
a single network device. Revert this change to restore the 1:1 mapping
by allocating the network device at the instance level (alloc_inst).
Reported-by: David Heidelberg <david@ixit.cz>
Closes: https://lore.kernel.org/linux-usb/70b558ea-a12e-4170-9b8e-c951131249af@ixit.cz/
Fixes: 56a512a9b410 ("usb: gadget: f_ncm: align net_device lifecycle with bind/unbind")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-5-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 0c0981126b99288ed354d3d414c8a5fd42ac9e25.
This commit is being reverted as part of a series-wide revert.
By deferring the net_device allocation to the bind() phase, a single
function instance will spawn multiple network devices if it is symlinked
to multiple USB configurations.
This causes regressions for userspace tools (like the postmarketOS DHCP
daemon) that rely on reading the interface name (e.g., "usb0") from
configfs. Currently, configfs returns the template "usb%d", causing the
userspace network setup to fail.
Crucially, because this patch breaks the 1:1 mapping between the
function instance and the network device, this naming issue cannot
simply be patched. Configfs only exposes a single 'ifname' attribute per
instance, making it impossible to accurately report the actual interface
name when multiple underlying network devices can exist for that single
instance.
All configurations tied to the same function instance are meant to share
a single network device. Revert this change to restore the 1:1 mapping
by allocating the network device at the instance level (alloc_inst).
Reported-by: David Heidelberg <david@ixit.cz>
Closes: https://lore.kernel.org/linux-usb/70b558ea-a12e-4170-9b8e-c951131249af@ixit.cz/
Fixes: 56a512a9b410 ("usb: gadget: f_ncm: align net_device lifecycle with bind/unbind")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-4-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 56a512a9b4107079f68701e7d55da8507eb963d9.
This commit is being reverted as part of a series-wide revert.
By deferring the net_device allocation to the bind() phase, a single
function instance will spawn multiple network devices if it is symlinked
to multiple USB configurations.
This causes regressions for userspace tools (like the postmarketOS DHCP
daemon) that rely on reading the interface name (e.g., "usb0") from
configfs. Currently, configfs returns the template "usb%d", causing the
userspace network setup to fail.
Crucially, because this patch breaks the 1:1 mapping between the
function instance and the network device, this naming issue cannot
simply be patched. Configfs only exposes a single 'ifname' attribute per
instance, making it impossible to accurately report the actual interface
name when multiple underlying network devices can exist for that single
instance.
All configurations tied to the same function instance are meant to share
a single network device. Revert this change to restore the 1:1 mapping
by allocating the network device at the instance level (alloc_inst).
Reported-by: David Heidelberg <david@ixit.cz>
Closes: https://lore.kernel.org/linux-usb/70b558ea-a12e-4170-9b8e-c951131249af@ixit.cz/
Fixes: 56a512a9b410 ("usb: gadget: f_ncm: align net_device lifecycle with bind/unbind")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-3-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit fde0634ad9856b3943a2d1a8cc8de174a63ac840.
This commit is being reverted as part of a series-wide revert.
By deferring the net_device allocation to the bind() phase, a single
function instance will spawn multiple network devices if it is symlinked
to multiple USB configurations.
This causes regressions for userspace tools (like the postmarketOS DHCP
daemon) that rely on reading the interface name (e.g., "usb0") from
configfs. Currently, configfs returns the template "usb%d", causing the
userspace network setup to fail.
Crucially, because this patch breaks the 1:1 mapping between the
function instance and the network device, this naming issue cannot
simply be patched. Configfs only exposes a single 'ifname' attribute per
instance, making it impossible to accurately report the actual interface
name when multiple underlying network devices can exist for that single
instance.
All configurations tied to the same function instance are meant to share
a single network device. Revert this change to restore the 1:1 mapping
by allocating the network device at the instance level (alloc_inst).
Reported-by: David Heidelberg <david@ixit.cz>
Closes: https://lore.kernel.org/linux-usb/70b558ea-a12e-4170-9b8e-c951131249af@ixit.cz/
Fixes: 56a512a9b410 ("usb: gadget: f_ncm: align net_device lifecycle with bind/unbind")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-2-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 0d6c8144ca4d93253de952a5ea0028c19ed7ab68.
This commit is being reverted as part of a series-wide revert.
By deferring the net_device allocation to the bind() phase, a single
function instance will spawn multiple network devices if it is symlinked
to multiple USB configurations.
This causes regressions for userspace tools (like the postmarketOS DHCP
daemon) that rely on reading the interface name (e.g., "usb0") from
configfs. Currently, configfs returns the template "usb%d", causing the
userspace network setup to fail.
Crucially, because this patch breaks the 1:1 mapping between the
function instance and the network device, this naming issue cannot
simply be patched. Configfs only exposes a single 'ifname' attribute per
instance, making it impossible to accurately report the actual interface
name when multiple underlying network devices can exist for that single
instance.
All configurations tied to the same function instance are meant to share
a single network device. Revert this change to restore the 1:1 mapping
by allocating the network device at the instance level (alloc_inst).
Reported-by: David Heidelberg <david@ixit.cz>
Closes: https://lore.kernel.org/linux-usb/70b558ea-a12e-4170-9b8e-c951131249af@ixit.cz/
Fixes: 56a512a9b410 ("usb: gadget: f_ncm: align net_device lifecycle with bind/unbind")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260309-f-ncm-revert-v2-1-ea2afbc7d9b2@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
message
dp_altmode_configure sets the signaling rate to the current
configuration's rate and then shifts the value to the Select
Configuration bitfield. On the initial configuration, dp->data.conf
is 0 to begin with, so the signaling rate field is never set, which
leads to some DisplayPort Alt Mode partners sending NAK to the
Configure message.
Set the signaling rate to the capabilities supported by both the
port and the port partner. If the cable supports DisplayPort Alt Mode,
then include its capabilities as well.
Fixes: a17fae8fc38e ("usb: typec: Add Displayport Alternate Mode 2.1 Support")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260310204106.3939862-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The condition for checking the disabled pinctrl state incorrectly checks
gf->enabled_state instead of gf->disabled_state. This causes misleading
error messages and could lead to incorrect behavior when only one of the
pinctrl states is defined.
Fix the condition to properly check gf->disabled_state.
Fixes: 9d3b5086f6d4 ("mtd: physmap_of_gemini: Handle pin control")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This patch adds the necessary PCI ID for Intel Nova Lake -H
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260309130204.208661-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Similar to other Huawei LTE modules using this quirk, this version with
another vid/pid suffers from spurious wakeups.
Setting the quirk fixes the issue for this device as well.
Cc: stable <stable@kernel.org>
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20260306172817.2098898-1-wse@tuxedocomputers.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To correctly convert bInterval as interval_duration:
interval_duration = 2^(bInterval-1) * frame_interval
Current code uses a wrong left shift operand, computing 2^bInterval
instead of 2^(bInterval-1).
Fixes: 010dc57cb516 ("usb: gadget: uvc: fix interval_duration calculation")
Cc: stable <stable@kernel.org>
Signed-off-by: Junzhong Pan <panjunzhong@linux.spacemit.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260306-fix-uvc-interval-v1-1-9a2df6859859@linux.spacemit.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Baikal SoC
As noticed in the discussion [1] the Baikal SoC and platforms
are not going to be finalized, hence remove stale code.
Link: https://lore.kernel.org/lkml/22b92ddf-6321-41b5-8073-f9c7064d3432@infradead.org/ [1]
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Michal reported and debgged a NULL pointer dereference bug in the
recently added portli debugfs files
Oops is caused when there are more port registers counted in
xhci->max_ports than ports reported by Supported Protocol capabilities.
This is possible if max_ports is more than maximum port number, or
if there are gaps between ports of different speeds the 'Supported
Protocol' capabilities.
In such cases port->rhub will be NULL so we can't reach xhci behind it.
Add an explicit NULL check for this case, and print portli in hex
without dereferencing port->rhub.
Reported-by: Michal Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20260304103856.48b785fd.michal.pecio@gmail.com
Fixes: 384c57ec7205 ("usb: xhci: Add debugfs support for xHCI Port Link Info (PORTLI) register.")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260304223639.3882398-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHCI controller reports a Host Controller Error (HCE) in UAS Storage
Device plug/unplug scenarios on Android devices. HCE is checked in
xhci_irq() function and causes an interrupt storm (since the interrupt
isn’t cleared), leading to severe system-level faults.
When the xHC controller reports HCE in the interrupt handler, the driver
only logs a warning and assumes xHC activity will stop as stated in xHCI
specification. An interrupt storm does however continue on some hosts
even after HCE, and only ceases after manually disabling xHC interrupt
and stopping the controller by calling xhci_halt().
Add xhci_halt() to xhci_irq() function where STS_HCE status is checked,
mirroring the existing error handling pattern used for STS_FATAL errors.
This only fixes the interrupt storm. Proper HCE recovery requires resetting
and re-initializing the xHC.
CC: stable@vger.kernel.org
Signed-off-by: Dayu Jiang <jiangdayu@xiaomi.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260304223639.3882398-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_alloc_command() allocates a command structure and, when the
second argument is true, also allocates a completion structure.
Currently, the error handling path in xhci_disable_slot() only frees
the command structure using kfree(), causing the completion structure
to leak.
Use xhci_free_command() instead of kfree(). xhci_free_command() correctly
frees both the command structure and the associated completion structure.
Since the command structure is allocated with zero-initialization,
command->in_ctx is NULL and will not be erroneously freed by
xhci_free_command().
This bug was found using an experimental static analysis tool we are
developing. The tool is based on the LLVM framework and is specifically
designed to detect memory management issues. It is currently under
active development and not yet publicly available, but we plan to
open-source it after our research is published.
The bug was originally detected on v6.13-rc1 using our static analysis
tool, and we have verified that the issue persists in the latest mainline
kernel.
We performed build testing on x86_64 with allyesconfig using GCC=11.4.0.
Since triggering these error paths in xhci_disable_slot() requires specific
hardware conditions or abnormal state, we were unable to construct a test
case to reliably trigger these specific error paths at runtime.
Fixes: 7faac1953ed1 ("xhci: avoid race between disable slot command and host runtime suspend")
CC: stable@vger.kernel.org
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260304223639.3882398-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Quoting the bug report:
Due to compiler optimization or CPU out-of-order execution, the
desc->length update can be reordered before the memmove. If this
happens, wdm_read() can see the new length and call copy_to_user() on
uninitialized memory. This also violates LKMM data race rules [1].
Fix it by using WRITE_ONCE and memory barriers.
Fixes: afba937e540c9 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Closes: https://lore.kernel.org/linux-usb/CALbr=LbrUZn_cfp7CfR-7Z5wDTHF96qeuM=3fO2m-q4cDrnC4A@mail.gmail.com/
Reported-by: Gui-Dong Han <hanguidong02@gmail.com>
Reviewed-by: Gui-Dong Han <hanguidong02@gmail.com>
Link: https://patch.msgid.link/20260304130116.1721682-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In usbhs_remove(), the driver frees resources (including the pipe array)
while the interrupt handler (usbhs_interrupt) is still registered. If an
interrupt fires after usbhs_pipe_remove() but before the driver is fully
unbound, the ISR may access freed memory, causing a use-after-free.
Fix this by calling devm_free_irq() before freeing resources. This ensures
the interrupt handler is both disabled and synchronized (waits for any
running ISR to complete) before usbhs_pipe_remove() is called.
Fixes: f1407d5c6624 ("usb: renesas_usbhs: Add Renesas USBHS common code")
Cc: stable <stable@kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260303073344.34577-1-fanwu01@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CH343 USB/serial adapter is as buggy as it is popular (very).
One of its quirks is that despite being capable of signalling a
BREAK condition, it doesn't advertise it.
This used to work nonetheless until 66aad7d8d3ec5 ("usb: cdc-acm:
return correct error code on unsupported break") applied some
reasonable restrictions, preventing breaks from being emitted on
devices that do not advertise CAP_BRK.
Add a quirk for this particular device, so that breaks can still
be produced on some of my machines attached to my console server.
Fixes: 66aad7d8d3ec5 ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260301124440.1192752-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
check_command_size_in_blocks()
The `check_command_size_in_blocks()` function calculates the data size
in bytes by left shifting `common->data_size_from_cmnd` by the block
size (`common->curlun->blkbits`). However, it does not validate whether
this shift operation will cause an integer overflow.
Initially, the block size is set up in `fsg_lun_open()` , and the
`common->data_size_from_cmnd` is set up in `do_scsi_command()`. During
initialization, there is no integer overflow check for the interaction
between two variables.
So if a malicious USB host sends a SCSI READ or WRITE command
requesting a large amount of data (`common->data_size_from_cmnd`), the
left shift operation can wrap around. This results in a truncated data
size, which can bypass boundary checks and potentially lead to memory
corruption or out-of-bounds accesses.
Fix this by using the check_shl_overflow() macro to safely perform the
shift and catch any overflows.
Fixes: 144974e7f9e3 ("usb: gadget: mass_storage: support multi-luns with different logic block size")
Signed-off-by: Seungjin Bae <eeodqql09@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260228104324.1696455-2-eeodqql09@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When adding dynamic configuration for bInterval, the value was removed
from the static SuperSpeed endpoint descriptors but was not set from the
configured value in hidg_bind(). Thus at SuperSpeed the interrupt
endpoints have bInterval as zero which is not valid per the USB
specification.
Add the missing setting for SuperSpeed endpoints.
Fixes: ea34925f5b2ee ("usb: gadget: hid: allow dynamic interval configuration via configfs")
Cc: stable <stable@kernel.org>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://patch.msgid.link/20260227111540.431521-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some USB devices incorrectly report bNumConfigurations as 0 in their
device descriptor, which causes the USB core to reject them during
enumeration.
logs:
usb 1-2: device descriptor read/64, error -71
usb 1-2: no configurations
usb 1-2: can't read configurations, error -22
However, these devices actually work correctly when
treated as having a single configuration.
Add a new quirk USB_QUIRK_FORCE_ONE_CONFIG to handle such devices.
When this quirk is set, assume the device has 1 configuration instead
of failing with -EINVAL.
This quirk is applied to the device with VID:PID 5131:2007 which
exhibits this behavior.
Signed-off-by: Jie Deng <dengjie03@kylinos.cn>
Link: https://patch.msgid.link/20260227084931.1527461-1-dengjie03@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If get_1284_register() fails, the usb device reference count is
incorrect and needs to be properly dropped before returning. That will
happen when the kref is dropped in the call to destroy_priv(), so jump
to that error path instead of returning directly.
Cc: stable <stable@kernel.org>
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022342-smokiness-stove-d792@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb_control_msg(), usb_bulk_msg(), and usb_interrupt_msg() APIs in
usbcore allow unlimited timeout durations. And since they use
uninterruptible waits, this leaves open the possibility of hanging a
task for an indefinitely long time, with no way to kill it short of
unplugging the target device.
To prevent this sort of problem, enforce a maximum limit on the length
of these unkillable timeouts. The limit chosen here, somewhat
arbitrarily, is 60 seconds. On many systems (although not all) this
is short enough to avoid triggering the kernel's hung-task detector.
In addition, clear up the ambiguity of negative timeout values by
treating them the same as 0, i.e., using the maximum allowed timeout.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/3acfe838-6334-4f6d-be7c-4bb01704b33d@rowland.harvard.edu/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/15fc9773-a007-47b0-a703-df89a8cf83dd@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usbtmc driver accepts timeout values specified by the user in an
ioctl command, and uses these timeouts for some usb_bulk_msg() calls.
Since the user can specify arbitrarily long timeouts and
usb_bulk_msg() uses unkillable waits, call usb_bulk_msg_killable()
instead to avoid the possibility of the user hanging a kernel thread
indefinitely.
Reported-by: syzbot+25ba18e2c5040447585d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/8e1c7ac5-e076-44b0-84b8-1b34b20f0ae1@suse.com/T/#t
Tested-by: syzbot+25ba18e2c5040447585d@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 048c6d88a021 ("usb: usbtmc: Add ioctls to set/get usb timeout")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/81c6fc24-0607-40f1-8c20-5270dab2fad5@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The synchronous message API in usbcore (usb_control_msg(),
usb_bulk_msg(), and so on) uses uninterruptible waits. However,
drivers may call these routines in the context of a user thread, which
means it ought to be possible to at least kill them.
For this reason, introduce a new usb_bulk_msg_killable() function
which behaves the same as usb_bulk_msg() except for using
wait_for_completion_killable_timeout() instead of
wait_for_completion_timeout(). The same can be done later for
usb_control_msg() later on, if it turns out to be needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/linux-usb/3acfe838-6334-4f6d-be7c-4bb01704b33d@rowland.harvard.edu/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/248628b4-cc83-4e81-a620-3ce4e0376d41@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the error path from the usb_phy_roothub_set_mode() function.
The code is clearly wrong, because phy_set_mode() calls can't be
balanced with phy_power_off() calls.
Additionally, the usb_phy_roothub_set_mode() function is called only
from usb_add_hcd() before it powers on the PHYs, so powering off those
makes no sense anyway.
Presumably, the code is copy-pasted from the phy_power_on() function
without adjusting the error handling.
Cc: stable@vger.kernel.org # v5.1+
Fixes: b97a31348379 ("usb: core: comply to PHY framework")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20260218-usb-phy-poweroff-fix-v1-1-66e6831e860e@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To document how the helpers should be used before a subsequent change
adds new locations that these helpers will be used.
Reviewed-by: Ovidiu (Ovi) Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHAT]
Add FRAME_SKIPPING_ERROR_STATUS to dpcd_replay_configuration.
Add received_frame_skipping_error_hpd to replay_config.
Add REPLAY_GENERAL_CMD_SET_COASTING_VTOTAL_WITHOUT_FRAME_UPDATE to
dmub_cmd_replay_general_subtype.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
We're checking surface and stream updates after they've been applied to
their respective states within `update_planes_and_stream_state`.
Medium updates under the HWSS V3 fast path that are not supported or
tested are getting implicitly if they don't trigger a DML validation
and getting updated in place on the dc->current_state context.
[HOW]
Fix this issue by moving up the fast path determination check prior
to `update_planes_and_stream_state`. This is how the V2 path works
and how the V3 path used to work prior to the refactors in this area.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Commit 4c595e75110e ("drm/amd/display: Migrate DCCG registers access
from hwseq to dccg component.") moved register writes from hwseq to
dccg2_*() functions but did not add the registers to the DCCG register
list macros. The struct fields default to 0, so REG_WRITE() targets
MMIO offset 0, causing a GPU hang on resume (seen on DCN21/DCN30
during IGT kms_cursor_crc@cursor-suspend).
Add
- MICROSECOND_TIME_BASE_DIV
- MILLISECOND_TIME_BASE_DIV
- DCCG_GATE_DISABLE_CNTL
- DCCG_GATE_DISABLE_CNTL2
- DC_MEM_GLOBAL_PWR_REQ_CNTL
to macros in dcn20_dccg.h, dcn301_dccg.h, dcn31_dccg.h, and dcn314_dccg.h.
Fixes: 4c595e75110e ("drm/amd/display: Migrate DCCG registers access from hwseq to dccg component.")
Reported-by: Rafael Passos <rafael@rcpassos.me>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[HOW]
Add Replay recovery flow so that when HPD occurs and ESD is detected,
Replay can restore the system back to normal.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Weiguang Li <wei-guang.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Add underflow detection for later ASICs.
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Extend COLOR_ENCODING and COLOR_RANGE property creation to overlay
planes in addition to primary planes. This allows overlay planes to
use YUV formats with proper color space configuration when the
hardware supports NV12/P010 formats.
These properties control the YUV-to-RGB conversion matrix selection
(BT.601/BT.709/BT.2020) and range handling (limited/full range).
Assisted-by: Claude: claude-sonnet-4.5
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
