| Age | Commit message (Collapse) | Author |
|---|
|
Correct the struct member names to avoid kernel-doc warnings:
Warning: include/linux/mfd/cgbc.h:38 struct member 'version' not
described in 'cgbc_device_data'
Warning: ../include/linux/mfd/cgbc.h:38 struct member 'lock' not
described in 'cgbc_device_data'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260309214223.749088-2-rdunlap@infradead.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Convert fsl-imx25-tsadc.txt to yaml format.
Additional changes:
- Add ranges.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260211-yaml_mfd-v1-2-05cb48bc6f09@nxp.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260305104051.15727-1-johan@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Convert dln2_probe and dln2_setup_rx_urbs to use devm_kzalloc() and
devm_kmalloc() respectively. This simplifies resource management by
allowing the removal of manual kfree() calls in dln2_free() and
dln2_free_rx_urbs().
Additionally, update bare 'unsigned' types to 'unsigned int' to satisfy
checkpatch.pl warnings and comply with the Linux kernel coding style.
Signed-off-by: Subhash Rawat <rawatsubhash02@gmail.com>
Link: https://patch.msgid.link/20260303183236.574940-1-rawatsubhash02@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add the cell for the macsmc-power driver so it is probed by the
MFD core.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Sven Peter <sven@kernel.org>
Signed-off-by: Michael Reeves <michael.reeves077@gmail.com>
Link: https://patch.msgid.link/20260217-b4-macsmc-power-v7-2-4a4d63664362@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
CIDs set for MT6328, MT6331 and MT6332 are not appropriate.
Many Android downstream kernels define CID as below,
MT6328:
#define PMIC6328_E1_CID_CODE 0x2810
#define PMIC6328_E2_CID_CODE 0x2820
#define PMIC6328_E3_CID_CODE 0x2830
MT6331/MT6332:
#define PMIC6331_E1_CID_CODE 0x3110
#define PMIC6331_E2_CID_CODE 0x3120
#define PMIC6331_E3_CID_CODE 0x3130
#define PMIC6332_E1_CID_CODE 0x3210
#define PMIC6332_E2_CID_CODE 0x3220
#define PMIC6332_E3_CID_CODE 0x3230
The current configuration incorrectly uses the revision code as the CID.
Therefore, the driver cannot detect the same PMIC of different revisions.
(E1/E2 for MT6328, E1/E3 for MT6331/MT6332)
Based on these, the CID of MT6328, MT6331 and MT6332 should be corrected.
Additionally, the incorrect MT6331/MT6332 CID overlaps with the MT6320's
actual CID:
#define PMIC6320_E1_CID_CODE 0x1020
#define PMIC6320_E2_CID_CODE 0x2020
This causes a conflict in the switch-case statement of mt6397-irq.c,
this prevents adding support for MT6320.
Signed-off-by: Akari Tsuyukusa <akkun11.open@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20260302140045.651727-1-akkun11.open@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add supply properties that match the P1 PMIC's actual hardware topology
where each buck converter has its own VIN pin and LDO groups share
common input pins. Supply names are defined according to the pinout
names in the P1 datasheet.
The existing "vin-supply" is dropped from the binding document as the
updated spacemit P1 driver no longer parses it. Only the per-rail names
("vin1-supply", "vin2-supply", ...) are supported.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20260206-spacemit-p1-v4-1-8f695d93811e@riscstar.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
One of the users of this driver - meraki-mx100 - abuses the software
node API by setting up a dummy software node without any logical link to
this GPIO controller and uses the fact that the GPIO core matches the
controller's label against the swnode's name to make the lookup work.
We want to remove this behavior from GPIOLIB in favor of actual matching
of firmware nodes but that would break this user. To facilitate that:
create a software node for the GPIO controller cell and expose its
address in the provided MFD header.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260218-meraki-swnodes-v2-1-92c521da241c@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The XLCDC IP supports parallel RGB, MIPI DSI and LVDS Display.
The LCD Generic clock (sys_clk) is used for Parallel RGB and MIPI
displays, while the LVDS PLL clock (lvds_pll_clk) is used for LVDS
displays.Since both the clocks cannot co-exist together in the DT
for a given display, this patch tries sys_clk first (RGB/MIPI),
fallback to lvds_pll_clk (LVDS).
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
Link: https://patch.msgid.link/20260223101920.284697-2-manikandan.m@microchip.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260305130358.24681-1-johan@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
File-scope 'max77705_pm_ops' is not used outside of this unit, so make
it static to silence sparse warning:
max77705.c:160:1: warning: symbol 'max77705_pm_ops' was not declared. Should it be static?
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260216110432.160084-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
It is normally expected to get out of deeper power saving states by
pressing the power button, so enable wakeup for it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20260206093757.573377-1-andreas@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Attempt to shut down again, in case the first attempt failed.
The STPMIC1 might get confused and the first regmap_update_bits()
returns with -ETIMEDOUT / -110 . If that or similar transient
failure occurs, try to shut down again. If the second attempt
fails, there is some bigger problem, report it to user.
Cc: stable@vger.kernel.org
Fixes: 6e9df38f359a ("mfd: stpmic1: Add PMIC poweroff via sys-off handler")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Link: https://patch.msgid.link/20260122111423.62591-1-marex@nabladev.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The memory allocated for cell.name using kmemdup() is not freed when
mfd_add_devices() fails. Fix that by using devm_kmemdup().
Fixes: 8e00593557c3 ("mfd: Add mc13892 support to mc13xxx")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20260120102622.66921-1-nihaal@cse.iitm.ac.in
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The function iommufd_hw_pagetable_alloc() was renamed to
iommufd_hwpt_paging_alloc() by commit 89db31635c87
("iommufd: Derive iommufd_hwpt_paging from
iommufd_hw_pagetable"). Update the stale reference in
iommufd_device_auto_get_domain().
Link: https://patch.msgid.link/r/20260321105759.6832-1-kexinsun@smail.nju.edu.cn
Assisted-by: unnamed:deepseek-v3.2 coccinelle
Signed-off-by: Kexin Sun <kexinsun@smail.nju.edu.cn>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Convention expressed in example-schema.yaml is to place
"unevaluatedProperties" part just before example. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260325110849.127051-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The binding does not reference any other schema, thus should use
"additionalProperties: false" to disallow any undocumented properties.
Correct the code and place this after "required:" block to match
convention expressed in example-schema.yaml.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260325110849.127051-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
C++ language requirements differ from those of C.
Also test the headers against C++ compilers to make sure no errors
creep in accidentally.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20260316-kbuild-uapi-c-v2-5-35d6d0ed863f@weissschuh.net
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
NULL works differently in C++ compared to C.
To allow testing the UAPI headers against C++ compilers, provide
a variant of NULL which works with those.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20260316-kbuild-uapi-c-v2-4-35d6d0ed863f@weissschuh.net
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
When building User Mode Linux SRCARCH is set to 'um', while the actual
underlying architecture is provided in HEADER_ARCH.
Allow the exclusion lists to work on UML by comparing against
HEADER_ARCH when that is available.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20260316-kbuild-uapi-c-v2-3-35d6d0ed863f@weissschuh.net
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
The argument to add the root of the UAPI header tree to the include path
is separated from the other arguments concerning the include path.
Move all include path arguments together for more consistency and
balanced line lengths.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20260316-kbuild-uapi-c-v2-2-35d6d0ed863f@weissschuh.net
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
Simplify the definition of cmd_hdrtest by moving some of it to a new
variable. This will both enable the upcoming reuse of those flags
and also the extension of cmd_hdrtest.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20260316-kbuild-uapi-c-v2-1-35d6d0ed863f@weissschuh.net
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
The number of the initialization table may exceed 2048.
Therefore, this patch removes the limitation and allows the driver to
allocate memory dynamically based on the size of the initialization table.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260325092017.3221640-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dquot_scan_active() can race with quota deactivation in
quota_release_workfn() like:
CPU0 (quota_release_workfn) CPU1 (dquot_scan_active)
============================== ==============================
spin_lock(&dq_list_lock);
list_replace_init(
&releasing_dquots, &rls_head);
/* dquot X on rls_head,
dq_count == 0,
DQ_ACTIVE_B still set */
spin_unlock(&dq_list_lock);
synchronize_srcu(&dquot_srcu);
spin_lock(&dq_list_lock);
list_for_each_entry(dquot,
&inuse_list, dq_inuse) {
/* finds dquot X */
dquot_active(X) -> true
atomic_inc(&X->dq_count);
}
spin_unlock(&dq_list_lock);
spin_lock(&dq_list_lock);
dquot = list_first_entry(&rls_head);
WARN_ON_ONCE(atomic_read(&dquot->dq_count));
The problem is not only a cosmetic one as under memory pressure the
caller of dquot_scan_active() can end up working on freed dquot.
Fix the problem by making sure the dquot is removed from releasing list
when we acquire a reference to it.
Fixes: 869b6ea1609f ("quota: Fix slow quotaoff")
Reported-by: Sam Sun <samsun1006219@gmail.com>
Link: https://lore.kernel.org/all/CAEkJfYPTt3uP1vAYnQ5V2ZWn5O9PLhhGi5HbOcAzyP9vbXyjeg@mail.gmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Add video and command mode destination format mappings for RGB101010,
and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
the new format value.
Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
older does not support this.
Required for 10 bit panels such as the BOE BF068MWM-TD0 found on the
Nothing Phone (3a).
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713721/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-5-ff6afc904115@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Add a helper for checking if the DSI hardware version is greater
than or equal to a given version, for use in a future change.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713719/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-4-ff6afc904115@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The MSM8998 DSI controller is v2.0.0 as stated in commit 7b8c9e203039
("drm/msm/dsi: Add support for MSM8998 DSI controller"). The value was
always correct just the name was wrong.
Rename and reorder to maintain version sorting.
Fixes: 7b8c9e203039 ("drm/msm/dsi: Add support for MSM8998 DSI controller")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713717/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-3-ff6afc904115@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Use default instead of listing unsupported formats explicitly, so the
switch statements don't need updating each time a new pixel format is
added.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713715/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-2-ff6afc904115@pm.me
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
During 3D workload, user is reporting hitting:
[ 413.361679] WARNING: drivers/gpu/drm/xe/xe_vm.c:1217 at vm_bind_ioctl_ops_unwind+0x1e2/0x2e0 [xe], CPU#7: vkd3d_queue/9925
[ 413.361944] CPU: 7 UID: 1000 PID: 9925 Comm: vkd3d_queue Kdump: loaded Not tainted 7.0.0-070000rc3-generic #202603090038 PREEMPT(lazy)
[ 413.361949] RIP: 0010:vm_bind_ioctl_ops_unwind+0x1e2/0x2e0 [xe]
[ 413.362074] RSP: 0018:ffffd4c25c3df930 EFLAGS: 00010282
[ 413.362077] RAX: 0000000000000000 RBX: ffff8f3ee817ed10 RCX: 0000000000000000
[ 413.362078] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 413.362079] RBP: ffffd4c25c3df980 R08: 0000000000000000 R09: 0000000000000000
[ 413.362081] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8f41fbf99380
[ 413.362082] R13: ffff8f3ee817e968 R14: 00000000ffffffef R15: ffff8f43d00bd380
[ 413.362083] FS: 00000001040ff6c0(0000) GS:ffff8f4696d89000(0000) knlGS:00000000330b0000
[ 413.362085] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
[ 413.362086] CR2: 00007ddfc4747000 CR3: 00000002e6262005 CR4: 0000000000f72ef0
[ 413.362088] PKRU: 55555554
[ 413.362089] Call Trace:
[ 413.362092] <TASK>
[ 413.362096] xe_vm_bind_ioctl+0xa9a/0xc60 [xe]
Which seems to hint that the vma we are re-inserting for the ops unwind
is either invalid or overlapping with something already inserted in the
vm. It shouldn't be invalid since this is a re-insertion, so must have
worked before. Leaving the likely culprit as something already placed
where we want to insert the vma.
Following from that, for the case where we do something like a rebind in
the middle of a vma, and one or both mapped ends are already compatible,
we skip doing the rebind of those vma and set next/prev to NULL. As well
as then adjust the original unmap va range, to avoid unmapping the ends.
However, if we trigger the unwind path, we end up with three va, with
the two ends never being removed and the original va range in the middle
still being the shrunken size.
If this occurs, one failure mode is when another unwind op needs to
interact with that range, which can happen with a vector of binds. For
example, if we need to re-insert something in place of the original va.
In this case the va is still the shrunken version, so when removing it
and then doing a re-insert it can overlap with the ends, which were
never removed, triggering a warning like above, plus leaving the vm in a
bad state.
With that, we need two things here:
1) Stop nuking the prev/next tracking for the skip cases. Instead
relying on checking for skip prev/next, where needed. That way on the
unwind path, we now correctly remove both ends.
2) Undo the unmap va shrinkage, on the unwind path. With the two ends
now removed the unmap va should expand back to the original size again,
before re-insertion.
v2:
- Update the explanation in the commit message, based on an actual IGT of
triggering this issue, rather than conjecture.
- Also undo the unmap shrinkage, for the skip case. With the two ends
now removed, the original unmap va range should expand back to the
original range.
v3:
- Track the old start/range separately. vma_size/start() uses the va
info directly.
Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/7602
Fixes: 8f33b4f054fc ("drm/xe: Avoid doing rebinds")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260318100208.78097-2-matthew.auld@intel.com
(cherry picked from commit aec6969f75afbf4e01fd5fb5850ed3e9c27043ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add MIPI_DSI_FMT_RGB101010 for 30 bit (10,10,10 RGB) pixel format,
corresponding to the packed 30 bit pixel stream defined in MIPI DSI
v1.3 Section 8.8.17.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713714/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-1-ff6afc904115@pm.me
[Acked by Maxime to be merged through msm-next on IRC on dri-devel]
[DB: moved RGB101010 to the end of enum mipi_dsi_pixel_format]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
DP_TRAINING_LANEx_SET
In analogix_dp_link_start(), &link_train.training_lane[] is used to
set phy PE/VS configurations, and buf[] is initialized with the same
values to set DPCD DP_TRAINING_LANEx_SET.
It makes sense to reuse &link_train.training_lane[] to set DPCD
DP_TRAINING_LANEx_SET, which can remove the redundant assignments
and make codes more concise.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20251111022103.1350183-1-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
|
|
During 3D workload, user is reporting hitting:
[ 413.361679] WARNING: drivers/gpu/drm/xe/xe_vm.c:1217 at vm_bind_ioctl_ops_unwind+0x1e2/0x2e0 [xe], CPU#7: vkd3d_queue/9925
[ 413.361944] CPU: 7 UID: 1000 PID: 9925 Comm: vkd3d_queue Kdump: loaded Not tainted 7.0.0-070000rc3-generic #202603090038 PREEMPT(lazy)
[ 413.361949] RIP: 0010:vm_bind_ioctl_ops_unwind+0x1e2/0x2e0 [xe]
[ 413.362074] RSP: 0018:ffffd4c25c3df930 EFLAGS: 00010282
[ 413.362077] RAX: 0000000000000000 RBX: ffff8f3ee817ed10 RCX: 0000000000000000
[ 413.362078] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 413.362079] RBP: ffffd4c25c3df980 R08: 0000000000000000 R09: 0000000000000000
[ 413.362081] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8f41fbf99380
[ 413.362082] R13: ffff8f3ee817e968 R14: 00000000ffffffef R15: ffff8f43d00bd380
[ 413.362083] FS: 00000001040ff6c0(0000) GS:ffff8f4696d89000(0000) knlGS:00000000330b0000
[ 413.362085] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
[ 413.362086] CR2: 00007ddfc4747000 CR3: 00000002e6262005 CR4: 0000000000f72ef0
[ 413.362088] PKRU: 55555554
[ 413.362089] Call Trace:
[ 413.362092] <TASK>
[ 413.362096] xe_vm_bind_ioctl+0xa9a/0xc60 [xe]
Which seems to hint that the vma we are re-inserting for the ops unwind
is either invalid or overlapping with something already inserted in the
vm. It shouldn't be invalid since this is a re-insertion, so must have
worked before. Leaving the likely culprit as something already placed
where we want to insert the vma.
Following from that, for the case where we do something like a rebind in
the middle of a vma, and one or both mapped ends are already compatible,
we skip doing the rebind of those vma and set next/prev to NULL. As well
as then adjust the original unmap va range, to avoid unmapping the ends.
However, if we trigger the unwind path, we end up with three va, with
the two ends never being removed and the original va range in the middle
still being the shrunken size.
If this occurs, one failure mode is when another unwind op needs to
interact with that range, which can happen with a vector of binds. For
example, if we need to re-insert something in place of the original va.
In this case the va is still the shrunken version, so when removing it
and then doing a re-insert it can overlap with the ends, which were
never removed, triggering a warning like above, plus leaving the vm in a
bad state.
With that, we need two things here:
1) Stop nuking the prev/next tracking for the skip cases. Instead
relying on checking for skip prev/next, where needed. That way on the
unwind path, we now correctly remove both ends.
2) Undo the unmap va shrinkage, on the unwind path. With the two ends
now removed the unmap va should expand back to the original size again,
before re-insertion.
v2:
- Update the explanation in the commit message, based on an actual IGT of
triggering this issue, rather than conjecture.
- Also undo the unmap shrinkage, for the skip case. With the two ends
now removed, the original unmap va range should expand back to the
original range.
v3:
- Track the old start/range separately. vma_size/start() uses the va
info directly.
Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/7602
Fixes: 8f33b4f054fc ("drm/xe: Avoid doing rebinds")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260318100208.78097-2-matthew.auld@intel.com
|
|
irq_domain_add_linear() is about to be removed, replace by the
more generic irq_domain_create_linear(),
see commit 42b8b16fe56c ("irqdomain: Drop irq_domain_add_*()
functions") for details.
Link: https://lore.kernel.org/r/a9de2f351ea71e4b794baaea8d9d790fbfac8d26.1774391374.git.chleroy@kernel.org
Signed-off-by: Christophe Leroy (CS GROUP) <chleroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into gpio/for-next
Pull in the SCMI GPIO driver along with its pinctrl dependencies.
|
|
`feature(raw_ref_op)` became stable in Rust 1.82.0 which is the current
MSRV of pin-init with no default features. Earlier Rust versions will
now need to enable `raw_ref_op` to continue to work with pin-init.
This reduces visual complexity and improves consistency with existing
reference syntax.
Suggested-by: Benno Lossin <lossin@kernel.org>
Link: https://github.com/Rust-for-Linux/linux/issues/1148
Closes: https://github.com/Rust-for-Linux/pin-init/issues/99
Signed-off-by: Antonio Hickey <contact@antoniohickey.com>
Link: https://github.com/Rust-for-Linux/pin-init/commit/e27763004e2f6616b089437fbe9b3719cd72bd5c
[ Reworded commit message. - Benno ]
Reviewed-by: Gary Guo <gary@garyguo.net>
Link: https://patch.msgid.link/20260319093542.3756606-6-lossin@kernel.org
Signed-off-by: Benno Lossin <lossin@kernel.org>
|
|
Add a macro for implementing `ZeroableOption` for `NonZero*` types.
`Option<NonZero*>` now automatically implements `Zeroable` trait by
implementing `ZeroableOption` for `NonZero*` types, which serves as a
blanket impl.
Closes: https://github.com/Rust-for-Linux/pin-init/issues/95
Signed-off-by: Hamdan-Khan <hamdankhan212@gmail.com>
Link: https://github.com/Rust-for-Linux/pin-init/commit/74f772641cd9670848fa360f4ebfd20fdb40bf78
[ Fixed a typo in the commit message. - Benno ]
Link: https://patch.msgid.link/20260319093542.3756606-5-lossin@kernel.org
Signed-off-by: Benno Lossin <lossin@kernel.org>
|
|
Currently the doc for `Zeroable` and `ZeroableOption` are filled with the
generated impl of tuples and fn pointers. Use the internal
"fake_variadics" feature to improve the rendered quality.
This makes use of an internal feature, however this is of minimal risk as
it's for documentation only, not activated during normal build, gated
behind `USE_RUSTC_FEATURES`, and can be removed at any time. This feature
is already used by serde and bevy to improve documentation quality.
For compilers that cannot use this feature, we still hide most generated
impls, and the existence of them are hinted by doc comments on the single
non-hidden impl.
Signed-off-by: Gary Guo <gary@garyguo.net>
Link: https://github.com/Rust-for-Linux/pin-init/commit/530c4eb79a449599e219821f9397f03250cc2aa4
[ Reordered `#[doc]` attributes and safety comments to avoid errors in
older versions of clippy. - Benno ]
Link: https://patch.msgid.link/20260319093542.3756606-4-lossin@kernel.org
Signed-off-by: Benno Lossin <lossin@kernel.org>
|
|
The three let bindings (in the bodies of `cast_init`, `cast_pin_init`
and the `init!` macro) are used to avoid the following compiler error in
Rust 1.78.0, 1.79.0, 1.80.0, 1.80.1, and 1.81.0 (just showing the one
for `cast_init`, the others are similar):
error[E0391]: cycle detected when computing type of opaque `cast_init::{opaque#0}`
--> src/lib.rs:1160:66
|
1160 | pub const unsafe fn cast_init<T, U, E>(init: impl Init<T, E>) -> impl Init<U, E> {
| ^^^^^^^^^^^^^^^
|
note: ...which requires borrow-checking `cast_init`...
--> src/lib.rs:1160:1
|
1160 | pub const unsafe fn cast_init<T, U, E>(init: impl Init<T, E>) -> impl Init<U, E> {
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
note: ...which requires const checking `cast_init`...
--> src/lib.rs:1160:1
|
1160 | pub const unsafe fn cast_init<T, U, E>(init: impl Init<T, E>) -> impl Init<U, E> {
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
= note: ...which requires computing whether `cast_init::{opaque#0}` is freeze...
= note: ...which requires evaluating trait selection obligation `cast_init::{opaque#0}: core::marker::Freeze`...
= note: ...which again requires computing type of opaque `cast_init::{opaque#0}`, completing the cycle
note: cycle used when computing type of `cast_init::{opaque#0}`
--> src/lib.rs:1160:66
|
1160 | pub const unsafe fn cast_init<T, U, E>(init: impl Init<T, E>) -> impl Init<U, E> {
| ^^^^^^^^^^^^^^^
= note: see https://rustc-dev-guide.rust-lang.org/overview.html#queries and https://rustc-dev-guide.rust-lang.org/query.html for more information
Once we raise the nightly-MSRV above 1.81, we can remove this
workaround.
Link: https://github.com/Rust-for-Linux/pin-init/commit/bb3e96f3e9a4f5fca80a22af883c7e5aa90f0893
[ Moved this commit after the previous one to avoid a build failure due
to unstable features. Changed the cfg to use `USE_RUSTC_FEAUTURES`.
- Benno ]
Reviewed-by: Gary Guo <gary@garyguo.net>
Link: https://patch.msgid.link/20260319093542.3756606-3-lossin@kernel.org
Signed-off-by: Benno Lossin <lossin@kernel.org>
|
|
We use some features that are already stable in later versions of Rust,
but only available as unstable features in older Rust versions that the
kernel needs to support.
Instead of checking if a feature is already stable, simply enable them
and allow the warning if the feature is already stable. This avoids the
need of hardcoding whether a feature has been stabilized at a given
version.
`#[feature(...)]` is used when cfg `USE_RUSTC_FEATURES` is enabled. The
build script automatically does this when a nightly compiler is detected
or `RUSTC_BOOTSTRAP` is set.
Signed-off-by: Gary Guo <gary@garyguo.net>
Link: https://github.com/Rust-for-Linux/pin-init/commit/885c5d83d7eb778a796d4a17380a0898b0d0a571
[ Added kernel build system changes to always enable USE_RUSTC_FEATURES.
Moved this commit earlier (swapped with the next one) to avoid a build
error. - Benno ]
Link: https://patch.msgid.link/20260319093542.3756606-2-lossin@kernel.org
Signed-off-by: Benno Lossin <lossin@kernel.org>
|
|
All CONFIG_ARCH_TEGRA_132_SOC-like symbols are now default for
ARCH_TEGRA, so drop redundant lines from defconfig. Tested with
comparing include/generated/autoconf.h.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
All CONFIG_ARCH_TEGRA_2x_SOC-like symbols are now default for
ARCH_TEGRA, so drop redundant lines from defconfigs. Tested with
comparing include/generated/autoconf.h.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
The NVIDIA Tegra238 SoC is an upcoming new chip. Add a Kconfig symbol to
allow fine-grained selection of support code for this chip.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
By convention, only one globally selectable ARCH_PLATFORM is expected
for given SoC platform, defined in arch/arm64/Kconfig.platforms or
arch/arm/mach-*/Kconfig, because we target a single multi-platform
kernel image.
Platforms wanting different granularity, e.g. due to size constraints on
their devices, should be sure that globally only one ARCH_PLATFORM is
selected in defconfig. Change Tegra per-SoC Kconfig entries to default
to ARCH_TEGRA allowing removal of these per-SoC parts from defconfigs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
[treding@nvidia.com: Fix ARCH_PLATFORM typo, correct spelling]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Instead of setting this flag in the iwl_mld_radiotap_put_tlv()
users, and not even all of them, set it inside the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260321192637.31eff369ccf2.If5cee8f7c767b937891abb6cccf2692068ba7758@changeid
|
|
When the firmware crashes, we print data to be able to know what
happened. The problem is that those prints became excessive as during
the course of the years, we added more data without ever removing the
prints that were no longer useful.
Instead of spamming the log with data that will not help anyone, limit
the prints to what is really needed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Eilon Rinat <eilon.rinat@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260321192637.3bb8b142ff48.Ieacb12bf3bc930a4c28824e31d8e06eda177ba78@changeid
|
|
The struct has been renamed to iwl_session_prot_cmd.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260321192637.56545b097d13.If468c6a666dcf3a52601604bfc8a1c4faa9d320c@changeid
|
|
Introduce a helper function that checks if a vif fw id is valid, and warns
if it isn't.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260321192637.b68d43db2ddc.I11b2b98e115da9eec8f603c5a01a0a9bcd040884@changeid
|
|
TDLS (Tunneled Direct Link Setup) requires single-link operation
for direct peer-to-peer communication, which is incompatible with
EMLSR (Enhanced Multi-Link Single Radio) mode where the radio
switches between multiple links.
Block EMLSR when the first TDLS peer is added and unblock when
the last TDLS peer is removed. The block/unblock APIs handle
exiting EMLSR and triggering link selection automatically.
Signed-off-by: Avinash Bhatt <avinash.bhatt@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260321192637.c1376b0259dd.I016587eb1570f7a7a64c0c95e0636e955a640350@changeid
|
