| Age | Commit message (Collapse) | Author |
|---|
|
Register P1:0x33 is written twice with the same value in the
'lane_2_mode_1632x1224' sequence. Remove one unnecessary write access.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The current settings for the "image vertical start" register appear to be
incorrect. While this only results in an incorrect start line for native
modes, this faulty setting causes actual problems in binning mode. At least
on an i.MX8MP test system, only corrupted frames could be received.
To correct this, the recommended settings from the reference register sets
are used for all modes. Since this shifts the start by one line, the Bayer
pattern also changes, which has also been corrected.
Fixes: 7be91e02ed57 ("media: i2c: Add ov08d10 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Set the device's runtime PM status and enable runtime PM before registering
the async sub-device. This is needed to avoid the case where the device is
runtime PM resumed while runtime PM has not been enabled yet.
Remove the related, non-driver-specific comment while at it.
Fixes: 7be91e02ed57 ("media: i2c: Add ov08d10 camera sensor driver")
Cc: stable@vger.kernel.org
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Remove cleanup of the register definitions from the TODO file.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The xfile/xmbuf shmem file descriptions are no longer as detailed as
they were when online fsck was first merged, because moving to static
strings in commit 60382993a2e180 ("xfs: get rid of the
xchk_xfile_*_descr calls") removed a memory allocation and hence a
source of failure.
However this makes encoding the description in the tracepoints sort of a
waste of memory. David Laight also points out that file_path doesn't
zero the whole buffer which causes exposure of stale trace bytes, and
Steven Rostedt wonders why we're not using a dynamic array for the file
path.
I don't think this is worth fixing, so let's just rip it out.
Cc: rostedt@goodmis.org
Cc: david.laight.linux@gmail.com
Link: https://lore.kernel.org/linux-xfs/20260323172204.work.979-kees@kernel.org/
Cc: stable@vger.kernel.org # v6.11
Fixes: 19ebc8f84ea12e ("xfs: fix file_path handling in tracepoints")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
xlog_recovery_iget* never set @ip to a valid pointer if they return
an error, so this irele will walk off a dangling pointer. Fix that.
Cc: stable@vger.kernel.org # v6.10
Fixes: ae673f534a3097 ("xfs: record inode generation in xattr update log intent items")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Long Li <leo.lilong@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Fix the duplicate word "kernel" in the comment on line 247.
Signed-off-by: haoyu.lu <hechushiguitu666@gmail.com>
Link: https://patch.msgid.link/20260326055628.10773-1-hechushiguitu666@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The DU driver creates device_link instances between the DU and CMMs, but
never deletes them. Fix it by introducing a rcar_du_cmm structure to
group the CMM device and device_link, and deleting the links at cleanup
time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://patch.msgid.link/20260323164526.2292491-5-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
|
|
Replace manual of_node_put() calls with __free(). This simplifies error
handling code and makes it less bug-prone.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://patch.msgid.link/20260323164526.2292491-4-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
|
|
The DU driver stores the CMM devices as pointers to struct
platform_device, and passes them to the API exposed by the CMM driver.
This is similar to how the VSP is handled, except that the VSP uses
struct device pointers. Replace the CMM platform_device pointers with
device pointers for consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://patch.msgid.link/20260323164526.2292491-3-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
|
|
The VSP serves as an interface to memory and a compositor to the DU. It
therefore needs to be suspended after and resumed before the DU, to be
properly stopped and restarted in a controlled fashion driven by the DU
driver. This currently works by chance. Avoid relying on luck by
enforcing the correct suspend/resume ordering with device links.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260323164526.2292491-2-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
|
|
When displaying pending SQEs for a MIXED ring, each 128-byte SQE
increments sq_head to skip the second slot, but the loop counter is not
adjusted. This can cause the loop to read past sq_tail by one entry for
each 128-byte SQE encountered, displaying SQEs that haven't been made
consumable yet by the application.
Match the kernel's own consumption logic in io_init_req() which
decrements what's left when consuming the extra slot.
Fixes: 1cba30bf9fdd ("io_uring: add support for IORING_SETUP_SQE_MIXED")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
calling drm_dev_unplug"
This reverts commit 6bee098b91417654703e17eb5c1822c6dfd0c01d.
Den 2026-03-25 kl. 22:11, skrev Simona Vetter:
> On Wed, Mar 25, 2026 at 10:26:40AM -0700, Guenter Roeck wrote:
>> Hi,
>>
>> On Fri, Mar 13, 2026 at 04:17:27PM +0100, Maarten Lankhorst wrote:
>>> When trying to do a rather aggressive test of igt's "xe_module_load
>>> --r reload" with a full desktop environment and game running I noticed
>>> a few OOPSes when dereferencing freed pointers, related to
>>> framebuffers and property blobs after the compositor exits.
>>>
>>> Solve this by guarding the freeing in drm_file with drm_dev_enter/exit,
>>> and immediately put the references from struct drm_file objects during
>>> drm_dev_unplug().
>>>
>>
>> With this patch in v6.18.20, I get the warning backtraces below.
>> The backtraces are gone with the patch reverted.
>
> Yeah, this needs to be reverted, reasoning below. Maarten, can you please
> take care of that and feed the revert through the usual channels? I don't
> think it's critical enough that we need to fast-track this into drm.git
> directly.
>
> Quoting the patch here again:
>
>> drivers/gpu/drm/drm_file.c | 5 ++++-
>> drivers/gpu/drm/drm_mode_config.c | 9 ++++++---
>> 2 files changed, 10 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/drm_file.c b/drivers/gpu/drm/drm_file.c
>> index ec820686b3021..f52141f842a1f 100644
>> --- a/drivers/gpu/drm/drm_file.c
>> +++ b/drivers/gpu/drm/drm_file.c
>> @@ -233,6 +233,7 @@ static void drm_events_release(struct drm_file *file_priv)
>> void drm_file_free(struct drm_file *file)
>> {
>> struct drm_device *dev;
>> + int idx;
>>
>> if (!file)
>> return;
>> @@ -249,9 +250,11 @@ void drm_file_free(struct drm_file *file)
>>
>> drm_events_release(file);
>>
>> - if (drm_core_check_feature(dev, DRIVER_MODESET)) {
>> + if (drm_core_check_feature(dev, DRIVER_MODESET) &&
>> + drm_dev_enter(dev, &idx)) {
>
> This is misplaced for two reasons:
>
> - Even if we'd want to guarantee that we hold a drm_dev_enter/exit
> reference during framebuffer teardown, we'd need to do this
> _consistently over all callsites. Not ad-hoc in just one place that a
> testcase hits. This also means kerneldoc updates of the relevant hooks
> and at least a bunch of acks from other driver people to document the
> consensus.
>
> - More importantly, this is driver responsibilities in general unless we
> have extremely good reasons to the contrary. Which means this must be
> placed in xe.
>
>> drm_fb_release(file);
>> drm_property_destroy_user_blobs(dev, file);
>> + drm_dev_exit(idx);
>> }
>>
>> if (drm_core_check_feature(dev, DRIVER_SYNCOBJ))
>> diff --git a/drivers/gpu/drm/drm_mode_config.c b/drivers/gpu/drm/drm_mode_config.c
>> index 84ae8a23a3678..e349418978f79 100644
>> --- a/drivers/gpu/drm/drm_mode_config.c
>> +++ b/drivers/gpu/drm/drm_mode_config.c
>> @@ -583,10 +583,13 @@ void drm_mode_config_cleanup(struct drm_device *dev)
>> */
>> WARN_ON(!list_empty(&dev->mode_config.fb_list));
>> list_for_each_entry_safe(fb, fbt, &dev->mode_config.fb_list, head) {
>> - struct drm_printer p = drm_dbg_printer(dev, DRM_UT_KMS, "[leaked fb]");
>> + if (list_empty(&fb->filp_head) || drm_framebuffer_read_refcount(fb) > 1) {
>> + struct drm_printer p = drm_dbg_printer(dev, DRM_UT_KMS, "[leaked fb]");
>
> This is also wrong:
>
> - Firstly, it's a completely independent bug, we do not smash two bugfixes
> into one patch.
>
> - Secondly, it's again a driver bug: drm_mode_cleanup must be called when
> the last drm_device reference disappears (hence the existence of
> drmm_mode_config_init), not when the driver gets unbound. The fact that
> this shows up in a callchain from a devres cleanup means the intel
> driver gets this wrong (like almost everyone else because historically
> we didn't know better).
>
> If we don't follow this rule, then we get races with this code here
> running concurrently with drm_file fb cleanups, which just does not
> work. Review pointed that out, but then shrugged it off with a confused
> explanation:
>
> https://lore.kernel.org/all/e61e64c796ccfb17ae673331a3df4b877bf42d82.camel@linux.intel.com/
>
> Yes this also means a lot of the other drm_device teardown that drivers
> do happens way too early. There is a massive can of worms here of a
> magnitude that most likely is much, much bigger than what you can
> backport to stable kernels. Hotunplug is _hard_.
Back to the drawing board, and fixing it in the intel display driver
instead.
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Fixes: 6bee098b9141 ("drm: Fix use-after-free on framebuffers and property blobs when calling drm_dev_unplug")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Simona Vetter <simona.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Link: https://patch.msgid.link/20260326082217.39941-2-dev@lankhorst.se
|
|
Much like the patch that dispatched (regular) work items, we also need to
dispatch delayed work items in order not to trigger the orphan rule. This
allows a drm::Device<T> to dispatch the delayed work to T::Data.
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Link: https://lore.kernel.org/r/20260323-aref-workitem-v3-4-f59729b812aa@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
|
|
The preceding patches added support for ARef<T> work items. By the same
token, add support for delayed work items too.
The rationale is the same: it may be convenient or even necessary at times
to implement HasDelayedWork directly on ARef<T>. A follow up patch will
also implement support for drm::Device as the first user.
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Link: https://lore.kernel.org/r/20260323-aref-workitem-v3-3-f59729b812aa@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
|
|
This implementation dispatches any work enqueued on ARef<drm::Device<T>> to
its driver-provided handler. It does so by building upon the newly-added
ARef<T> support in workqueue.rs in order to call into the driver
implementations for work_container_of and raw_get_work.
This is notably important for work items that need access to the drm
device, as it was not possible to enqueue work on a ARef<drm::Device<T>>
previously without failing the orphan rule.
The current implementation needs T::Data to live inline with drm::Device in
order for work_container_of to function. This restriction is already
captured by the trait bounds. Drivers that need to share their ownership of
T::Data may trivially get around this:
// Lives inline in drm::Device
struct DataWrapper {
work: ...,
// Heap-allocated, shared ownership.
data: Arc<DriverData>,
}
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Link: https://lore.kernel.org/r/20260323-aref-workitem-v3-2-f59729b812aa@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
|
|
Add support for the ARef<T> smart pointer. This allows an instance of
ARef<T> to handle deferred work directly, which can be convenient or even
necessary at times, depending on the specifics of the driver or subsystem.
The implementation is similar to that of Arc<T>, and a subsequent patch
will implement support for drm::Device as the first user. This is notably
important for work items that need access to the drm device, as it was not
possible to enqueue work on a ARef<drm::Device<T>> previously without
failing the orphan rule.
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Link: https://lore.kernel.org/r/20260323-aref-workitem-v3-1-f59729b812aa@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
|
|
When using global variables in a .c file only,it is necessary to add
the keyword "static", so here fix the warning.
sparse warnings: (new ones prefixed by >>)
>> sound/soc/renesas/dma-sh7760.c:62:3: sparse: sparse: symbol
'cam_pcm_data' was not declared. Should it be static?
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412171210.7a4vH3Ew-lkp@intel.com/
Link: https://patch.msgid.link/20260325022804.253353-1-songxiebing@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There's a potential mismatch between the memory reserved for statistics
and the amount of memory written.
gem_get_sset_count() correctly computes the number of stats based on the
active queues, whereas gem_get_ethtool_stats() indiscriminately copies
data using the maximum number of queues, and in the case the number of
active queues is less than MACB_MAX_QUEUES, this results in a OOB write
as observed in the KASAN splat.
==================================================================
BUG: KASAN: vmalloc-out-of-bounds in gem_get_ethtool_stats+0x54/0x78
[macb]
Write of size 760 at addr ffff80008080b000 by task ethtool/1027
CPU: [...]
Tainted: [E]=UNSIGNED_MODULE
Hardware name: raspberrypi rpi/rpi, BIOS 2025.10 10/01/2025
Call trace:
show_stack+0x20/0x38 (C)
dump_stack_lvl+0x80/0xf8
print_report+0x384/0x5e0
kasan_report+0xa0/0xf0
kasan_check_range+0xe8/0x190
__asan_memcpy+0x54/0x98
gem_get_ethtool_stats+0x54/0x78 [macb
926c13f3af83b0c6fe64badb21ec87d5e93fcf65]
dev_ethtool+0x1220/0x38c0
dev_ioctl+0x4ac/0xca8
sock_do_ioctl+0x170/0x1d8
sock_ioctl+0x484/0x5d8
__arm64_sys_ioctl+0x12c/0x1b8
invoke_syscall+0xd4/0x258
el0_svc_common.constprop.0+0xb4/0x240
do_el0_svc+0x48/0x68
el0_svc+0x40/0xf8
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1b0/0x1b8
The buggy address belongs to a 1-page vmalloc region starting at
0xffff80008080b000 allocated at dev_ethtool+0x11f0/0x38c0
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000
index:0xffff00000a333000 pfn:0xa333
flags: 0x7fffc000000000(node=0|zone=0|lastcpupid=0x1ffff)
raw: 007fffc000000000 0000000000000000 dead000000000122 0000000000000000
raw: ffff00000a333000 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff80008080b080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff80008080b100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff80008080b180: 00 00 00 00 00 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffff80008080b200: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffff80008080b280: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
==================================================================
Fix it by making sure the copied size only considers the active number of
queues.
Fixes: 512286bbd4b7 ("net: macb: Added some queue statistics")
Signed-off-by: Paolo Valerio <pvalerio@redhat.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260323191634.2185840-1-pvalerio@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- L2CAP: Fix deadlock in l2cap_conn_del()
- L2CAP: Fix ERTM re-init and zero pdu_len infinite loop
- L2CAP: Fix send LE flow credits in ACL link
- btintel: serialize btintel_hw_error() with hci_req_sync_lock
- btusb: clamp SCO altsetting table indices
* tag 'for-net-2026-03-25' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: clamp SCO altsetting table indices
Bluetooth: L2CAP: Fix ERTM re-init and zero pdu_len infinite loop
Bluetooth: L2CAP: Fix deadlock in l2cap_conn_del()
Bluetooth: btintel: serialize btintel_hw_error() with hci_req_sync_lock
Bluetooth: L2CAP: Fix send LE flow credits in ACL link
====================
Link: https://patch.msgid.link/20260325194358.618892-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The error path through vfio_pci_core_feature_dma_buf() ignores its
own advice to only use dma_buf_put() after dma_buf_export(), instead
falling through the entire unwind chain. In the unlikely event that
we encounter file descriptor exhaustion, this can result in an
unbalanced refcount on the vfio device and double free of allocated
objects.
Avoid this by moving the "put" directly into the error path and return
the errno rather than entering the unwind chain.
Reported-by: Renato Marziano <renato@marziano.top>
Fixes: 5d74781ebc86 ("vfio/pci: Add dma-buf export support for MMIO regions")
Cc: stable@vger.kernel.org
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@nvidia.com>
Link: https://lore.kernel.org/r/20260323215659.2108191-3-alex.williamson@nvidia.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
Replace trace_foo() with the new trace_call__foo() at sites already
guarded by trace_foo_enabled(), avoiding a redundant
static_branch_unlikely() re-evaluation inside the tracepoint.
trace_call__foo() calls the tracepoint callbacks directly without
utilizing the static branch again.
Cc: David Vernet <void@manifault.com>
Cc: Andrea Righi <arighi@nvidia.com>
Cc: Changwoo Min <changwoo@igalia.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Ben Segall <bsegall@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Valentin Schneider <vschneid@redhat.com>
Cc: Thomas Gleixner <tglx@kernel.org>
Cc: "Yury Norov [NVIDIA]" <yury.norov@gmail.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Roman Kisel <romank@linux.microsoft.com>
Cc: Joel Fernandes <joelagnelf@nvidia.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20260323160052.17528-3-vineeth@bitbyteword.org
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineeth Pillai (Google) <vineeth@bitbyteword.org>
Assisted-by: Claude:claude-sonnet-4-6
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Replace manual range and mask validations with netlink policy
annotations in ctnetlink code paths, so that the netlink core rejects
invalid values early and can generate extack errors.
- CTA_PROTOINFO_TCP_STATE: reject values > TCP_CONNTRACK_SYN_SENT2 at
policy level, removing the manual >= TCP_CONNTRACK_MAX check.
- CTA_PROTOINFO_TCP_WSCALE_ORIGINAL/REPLY: reject values > TCP_MAX_WSCALE
(14). The normal TCP option parsing path already clamps to this value,
but the ctnetlink path accepted 0-255, causing undefined behavior when
used as a u32 shift count.
- CTA_FILTER_ORIG_FLAGS/REPLY_FLAGS: use NLA_POLICY_MASK with
CTA_FILTER_F_ALL, removing the manual mask checks.
- CTA_EXPECT_FLAGS: use NLA_POLICY_MASK with NF_CT_EXPECT_MASK, adding
a new mask define grouping all valid expect flags.
Extracted from a broader nf-next patch by Florian Westphal, scoped to
ctnetlink for the fixes tree.
Fixes: c8e2078cfe41 ("[NETFILTER]: ctnetlink: add support for internal tcp connection tracking flags handling")
Signed-off-by: David Carlier <devnexen@gmail.com>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
process_sdp() declares union nf_inet_addr rtp_addr on the stack and
passes it to the nf_nat_sip sdp_session hook after walking the SDP
media descriptions. However rtp_addr is only initialized inside the
media loop when a recognized media type with a non-zero port is found.
If the SDP body contains no m= lines, only inactive media sections
(m=audio 0 ...) or only unrecognized media types, rtp_addr is never
assigned. Despite that, the function still calls hooks->sdp_session()
with &rtp_addr, causing nf_nat_sdp_session() to format the stale stack
value as an IP address and rewrite the SDP session owner and connection
lines with it.
With CONFIG_INIT_STACK_ALL_ZERO (default on most distributions) this
results in the session-level o= and c= addresses being rewritten to
0.0.0.0 for inactive SDP sessions. Without stack auto-init the
rewritten address is whatever happened to be on the stack.
Fix this by pre-initializing rtp_addr from the session-level connection
address (caddr) when available, and tracking via a have_rtp_addr flag
whether any valid address was established. Skip the sdp_session hook
entirely when no valid address exists.
Fixes: 4ab9e64e5e3c ("[NETFILTER]: nf_nat_sip: split up SDP mangling")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Skip expectations that do not reside in this netns.
Similar to e77e6ff502ea ("netfilter: conntrack: do not dump other netns's
conntrack entries via proc").
Fixes: 9b03f38d0487 ("netfilter: netns nf_conntrack: per-netns expectations")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
There is a teardown order issue in the driver. The SPI controller is
registered using devm_spi_register_controller(), which delays
unregistration of the SPI controller until after the fsl_lpspi_remove()
function returns.
As the fsl_lpspi_remove() function synchronously tears down the DMA
channels, a running SPI transfer triggers the following NULL pointer
dereference due to use after free:
| fsl_lpspi 42550000.spi: I/O Error in DMA RX
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[...]
| Call trace:
| fsl_lpspi_dma_transfer+0x260/0x340 [spi_fsl_lpspi]
| fsl_lpspi_transfer_one+0x198/0x448 [spi_fsl_lpspi]
| spi_transfer_one_message+0x49c/0x7c8
| __spi_pump_transfer_message+0x120/0x420
| __spi_sync+0x2c4/0x520
| spi_sync+0x34/0x60
| spidev_message+0x20c/0x378 [spidev]
| spidev_ioctl+0x398/0x750 [spidev]
[...]
Switch from devm_spi_register_controller() to spi_register_controller() in
fsl_lpspi_probe() and add the corresponding spi_unregister_controller() in
fsl_lpspi_remove().
Fixes: 5314987de5e5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20260319-spi-fsl-lpspi-fixes-v1-1-b433e435b2d8@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add trace_call__##name() as a companion to trace_##name(). When a
caller already guards a tracepoint with an explicit enabled check:
if (trace_foo_enabled() && cond)
trace_foo(args);
trace_foo() internally repeats the static_branch_unlikely() test, which
the compiler cannot fold since static branches are patched binary
instructions. This results in two static-branch evaluations for every
guarded call site.
trace_call__##name() calls __do_trace_##name() directly, skipping the
redundant static-branch re-check. This avoids leaking the internal
__do_trace_##name() symbol into call sites while still eliminating the
double evaluation:
if (trace_foo_enabled() && cond)
trace_invoke_foo(args); /* calls __do_trace_foo() directly */
Three locations are updated:
- __DECLARE_TRACE: invoke form omits static_branch_unlikely, retains
the LOCKDEP RCU-watching assertion.
- __DECLARE_TRACE_SYSCALL: same, plus retains might_fault().
- !TRACEPOINTS_ENABLED stub: empty no-op so callers compile cleanly
when tracepoints are compiled out.
Cc: Dmitry Ilvokhin <d@ilvokhin.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Aaron Conole <aconole@redhat.com>
Cc: Eelco Chaudron <echaudro@redhat.com>
Cc: Ilya Maximets <i.maximets@ovn.org>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Koby Elbaz <koby.elbaz@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Gautham R. Shenoy" <gautham.shenoy@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Eddie James <eajames@linux.ibm.com>
Cc: Andrew Jeffery <andrew@codeconstruct.com.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: David Airlie <airlied@gmail.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Danilo Krummrich <dakr@kernel.org>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Philipp Stanner <phasta@kernel.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <bentiss@kernel.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Nuno Sá <nuno.sa@analog.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Chris Mason <clm@fb.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: SeongJae Park <sj@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://patch.msgid.link/20260323160052.17528-2-vineeth@bitbyteword.org
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Vineeth Pillai (Google) <vineeth@bitbyteword.org>
Assisted-by: Claude:claude-sonnet-4-6
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
__nf_ct_expect_find() and nf_ct_expect_find_get() are called under
rcu_read_lock() but they dereference the master conntrack via
exp->master.
Since the expectation does not hold a reference on the master conntrack,
this could be dying conntrack or different recycled conntrack than the
real master due to SLAB_TYPESAFE_RCU.
Store the netns, the master_tuple and the zone in struct
nf_conntrack_expect as a safety measure.
This patch is required by the follow up fix not to dump expectations
that do not belong to this netns.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Holding reference on the expectation is not sufficient, the master
conntrack object can just go away, making exp->master invalid.
To access exp->master safely:
- Grab the nf_conntrack_expect_lock, this gets serialized with
clean_from_lists() which also holds this lock when the master
conntrack goes away.
- Hold reference on master conntrack via nf_conntrack_find_get().
Not so easy since the master tuple to look up for the master conntrack
is not available in the existing problematic paths.
This patch goes for extending the nf_conntrack_expect_lock section
to address this issue for simplicity, in the cases that are described
below this is just slightly extending the lock section.
The add expectation command already holds a reference to the master
conntrack from ctnetlink_create_expect().
However, the delete expectation command needs to grab the spinlock
before looking up for the expectation. Expand the existing spinlock
section to address this to cover the expectation lookup. Note that,
the nf_ct_expect_iterate_net() calls already grabs the spinlock while
iterating over the expectation table, which is correct.
The get expectation command needs to grab the spinlock to ensure master
conntrack does not go away. This also expands the existing spinlock
section to cover the expectation lookup too. I needed to move the
netlink skb allocation out of the spinlock to keep it GFP_KERNEL.
For the expectation events, the IPEXP_DESTROY event is already delivered
under the spinlock, just move the delivery of IPEXP_NEW under the
spinlock too because the master conntrack event cache is reached through
exp->master.
While at it, add lockdep notations to help identify what codepaths need
to grab the spinlock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use expect->helper in ctnetlink and /proc to dump the helper name.
Using nfct_help() without holding a reference to the master conntrack
is unsafe.
Use exp->master->helper in ctnetlink path if userspace does not provide
an explicit helper when creating an expectation to retain the existing
behaviour. The ctnetlink expectation path holds the reference on the
master conntrack and nf_conntrack_expect lock and the nfnetlink glue
path refers to the master ct that is attached to the skb.
Reported-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The expectation helper field is mostly unused. As a result, the
netfilter codebase relies on accessing the helper through exp->master.
Always set on the expectation helper field so it can be used to reach
the helper.
nf_ct_expect_init() is called from packet path where the skb owns
the ct object, therefore accessing exp->master for the newly created
expectation is safe. This saves a lot of updates in all callsites
to pass the ct object as parameter to nf_ct_expect_init().
This is a preparation patches for follow up fixes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Chris Arges reports high memory consumption with thousands of
containers, this patch revisits the array allocation logic.
For anonymous sets, start by 16 slots (which takes 256 bytes on x86_64).
Expand it by x2 until threshold of 512 slots is reached, over that
threshold, expand it by x1.5.
For non-anonymous set, start by 1024 slots in the array (which takes 16
Kbytes initially on x86_64). Expand it by x1.5.
Use set->ndeact to subtract deactivated elements when calculating the
number of the slots in the array, otherwise the array size array gets
increased artifically. Add special case shrink logic to deal with flush
set too.
The shrink logic is skipped by anonymous sets.
Use check_add_overflow() to calculate the new array size.
Add a WARN_ON_ONCE check to make sure elements fit into the new array
size.
Reported-by: Chris Arges <carges@cloudflare.com>
Fixes: 7e43e0a1141d ("netfilter: nft_set_rbtree: translate rbtree to array for binary search")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Reject rt match rules whose addrnr exceeds IP6T_RT_HOPS.
rt_mt6() expects addrnr to stay within the bounds of rtinfo->addrs[].
Validate addrnr during rule installation so malformed rules are rejected
before the match logic can use an out-of-range value.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Co-developed-by: Yuan Tan <yuantan098@gmail.com>
Signed-off-by: Yuan Tan <yuantan098@gmail.com>
Suggested-by: Xin Liu <bird@lzu.edu.cn>
Tested-by: Yuhang Zheng <z1652074432@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
__build_packet_message() manually constructs the NFULA_PAYLOAD netlink
attribute using skb_put() and skb_copy_bits(), bypassing the standard
nla_reserve()/nla_put() helpers. While nla_total_size(data_len) bytes
are allocated (including NLA alignment padding), only data_len bytes
of actual packet data are copied. The trailing nla_padlen(data_len)
bytes (1-3 when data_len is not 4-byte aligned) are never initialized,
leaking stale heap contents to userspace via the NFLOG netlink socket.
Replace the manual attribute construction with nla_reserve(), which
handles the tailroom check, header setup, and padding zeroing via
__nla_reserve(). The subsequent skb_copy_bits() fills in the payload
data on top of the properly initialized attribute.
Fixes: df6fb868d611 ("[NETFILTER]: nfnetlink: convert to generic netlink attribute functions")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The sub-device state lock has been already acquired when ccs_init_state()
is called. Do not try to acquire it again.
Reported-by: David Heidelberg <david@ixit.cz>
Fixes: a88883d1209c ("media: ccs: Rely on sub-device state locking")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Recent cleanup introduced a bug in the error path of
uvc_alloc_urb_buffers(). If there is not enough memory for the
allocation the following error will be triggered:
[ 739.196672] UBSAN: shift-out-of-bounds in mm/page_alloc.c:1403:22
[ 739.196710] shift exponent 52 is too large for 32-bit type 'int'
Resulting in:
[ 740.464422] BUG: unable to handle page fault for address: fffffac1c0800000
The reason for the bug is that usb_free_noncoherent is called with an
invalid size (0) instead of the actual size of the urb.
This patch takes care of that.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Closes: https://lore.kernel.org/linux-media/abycbXzYupZpGkvR@hyeyoo/T/#t
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: c824345288d1 ("media: uvcvideo: Pass allocation size directly to uvc_alloc_urb_buffer")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patch.msgid.link/20260320-uvc-urb-free-error-v1-1-b12cc3762a19@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
OF_GPIO is selected automatically on all OF systems. Any symbols it
controls also provide stubs so there's really no reason to select it
explicitly.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260316-gpio-of-kconfig-v2-4-de2f4b00a0e4@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Convert the Monolithic Power Systems MP8859 voltage regulator binding
from legacy text format to DT schema. This patch does not change any
functionality, the bindings remain the same.
Signed-off-by: Bhargav Joshi <rougueprince47@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260325230559.73527-1-rougueprince47@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Ioana Ciornei says:
====================
net: dpaa2-mac: export standard statistics
This patch set adds support for standard ethtool statistics - rmon,
eth-ctrl, eth-mac and pause - to dpaa2-mac and its users dpaa2-eth and
dpaa2-switch.
The first patch extends the firmware APIs related to MAC counters and
adds dpmac_get_statistics() which can be used to retrieve multiple counter
values through a single firmware call.
This new API is put in use in the second patch by gathering all
previously exported ethtool statistics through a single MC firmware
call. In this patch we are also adding the setup and cleanup
infrastructure which will be also used for the standard ethtool
counters.
The third patch adds the actual suppord for rmon, eth-ctrl, eth-mac and
pause statistics in dpaa2-mac and its users.
====================
Link: https://patch.msgid.link/20260323115039.3932600-1-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Take advantage of all the newly added MAC counters available through the
MC API and export them through the standard statistics structures -
rmon, eth-ctrl, eth-mac and pause.
A new version based feature is added into dpaa2-mac -
DPAA2_MAC_FEATURE_STANDARD_STATS - and based on the two memory zones
needed for gathering the MAC counters are setup for each statistics
group.
The dpmac_counter structure is extended with a new field - size_t offset
- which is being used to instruct the dpaa2_mac_transfer_stats()
function where exactly to store a counter value inside the standard
statistics structure.
The newly added support is used both in the dpaa2-eth driver as well as
the dpaa2-switch one.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260323115039.3932600-4-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The latest MC firmware version added a new command to retrieve all DPMAC
counters in a single firmware call. Use this new command, when possible,
in dpaa2-mac as well.
In order to use the dpmac_get_statistics() API, two DMA memory areas are
used: one to transmit what counters the driver is requesting and one to
receive the values of those counters. These memory areas are allocated
and DMA mapped at probe time so that we don't waste time at runtime.
And since we are planning to add rmon, eth-ctrl and other standard
statistics using the same infrastructure, make the setup and cleanup
processes as generic as possibile through the dpaa2_mac_setup_stats()
and dpaa2_mac_clear_stats() functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260323115039.3932600-3-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Extend the dpmac_counter_id enum with the newly added counters which can
be interrogated through the MC firmware. Also add the
dpmac_get_statistics() API which can be used to retrieve multiple MAC
counters through a single firmware command.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260323115039.3932600-2-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The mutex_lock()/mutex_unlock() pattern requires explicitly pairing
lock and unlock calls. Use guard(mutex) instead so the lock is
automatically released when the scope exits.
Convert to guard(mutex) in lm3642_torch_brightness_set(),
lm3642_strobe_brightness_set(), and lm3642_indicator_brightness_set().
Add #include <linux/cleanup.h> to support scoped guards.
Signed-off-by: Richard Lyu <richard.lyu@suse.com>
Link: https://patch.msgid.link/20260320035451.31071-1-richard.lyu@suse.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Detected by Smatch.
namei.c:890 exfat_mkdir() warn:
passing zero to 'ERR_PTR'
Signed-off-by: Yang Wen <anmuxixixi@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
Add the t4ka3 driver from:
https://github.com/kitakar5525/surface3-atomisp-cameras.git
With many cleanups / changes (almost a full rewrite) to make it suitable
for upstream:
* Remove the VCM and VCM-OTP support, the mainline kernel models VCMs and
calibration data eeproms as separate v4l2-subdev-s.
* Remove the integration-factor t4ka3_get_intg_factor() support and IOCTL,
this provided info to userspace through an atomisp private IOCTL.
* Turn atomisp specific exposure/gain IOCTL into standard v4l2 controls.
* Use normal ACPI power-management in combination with runtime-pm support
instead of atomisp specific GMIN power-management code.
* Turn into a standard V4L2 sensor driver using
v4l2_async_register_subdev_sensor().
* Add vblank, hblank, and link-freq controls; drop get_frame_interval().
* Use CCI register helpers.
* Calculate values for modes instead of using fixed register-value lists,
allowing arbritrary modes.
* Add get_selection() and set_selection() support
* Add a CSI2 bus configuration check
This was tested on a Xiaomi Mipad2 tablet which has a T4KA3 sensor with
DW9761 VCM as back sensor.
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add a V4L2 subdevice driver for the Omnivision OV2732 sensor.
The OV2732 is a 1/4" color CMOS 1080p (1920x1080) HD image sensor with
programmable controls like: gain, exposure, frame rate, image and windowing
size, horizontal mirror, vertical flip, cropping.
Signed-off-by: Walter Werner Schneider <contact@schnwalter.eu>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
[Sakari Ailus: Squashed Walter's fixup.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
Add bindings for OmniVision OV2732 image sensor.
Signed-off-by: Walter Werner Schneider <contact@schnwalter.eu>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
It is unexpected, but allowed to have no initial payload for a bytes
control and the code is prepared to handle this case, but the size check
missed this corner case.
Update the check for minimal size to allow the initial size to be 0.
Cc: stable@vger.kernel.org
Fixes: a653820700b8 ("ASoC: SOF: ipc4-topology: Correct the allocation size for bytes controls")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20260326075618.1603-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There's no point letting the driver probe if there is no flash, as
trying to do a firmware upload will fail. Move the code that attempts
to get the flash from firmware upload to probe, and let it emit a
message to users stating why auto-update is not supported.
The code currently could have a problem if there's a flash in
devicetree, but the system controller driver fails to get a pointer to
it from the mtd subsystem, which will cause
mpfs_sys_controller_get_flash() to return an error. Check for errors and
null, instead of just null, in the new clause.
CC: stable@vger.kernel.org
Fixes: ec5b0f1193ad4 ("firmware: microchip: add PolarFire SoC Auto Update support")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The SPI API is asymmetric and the controller is freed as part of
deregistration (unless it has been allocated using
devm_spi_alloc_host/target()).
A recent change converting the managed registration function to use
devm_add_action_or_reset() inadvertently introduced a (mostly
theoretical) regression where a non-devres managed controller could be
freed as part of failed registration. This in turn would lead to
use-after-free in controller driver error paths.
Fix this by taking another reference before calling
devm_add_action_or_reset() and not releasing it on errors for
non-devres allocated controllers.
An alternative would be a partial revert of the offending commit, but
it is better to handle this explicitly until the API has been fixed
(e.g. see 5e844cc37a5c ("spi: Introduce device-managed SPI controller
allocation")).
Fixes: b6376dbed8e1 ("spi: Simplify devm_spi_*_controller()")
Reported-by: Felix Gu <ustc.gu@gmail.com>
Link: https://lore.kernel.org/all/20260324145548.139952-1-ustc.gu@gmail.com/
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260325145319.1132072-1-johan@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
