| Age | Commit message (Collapse) | Author |
|---|
|
Convert the SMU15 table address messages to
smu_cmn_send_smc_msg_with_params() so they use the common SMU
multi-msgs helper instead of open-coding struct smu_msg_args.
No functional change intended.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SMU15 driver messages can carry multiple input parameters and return
values, but callers still have to build struct smu_msg_args directly.
Add common SMU multi-msgs helpers in smu_cmn and reuse them in the
single-parameter wrapper and the shared table transfer path.
Keep smu_cmn_send_smc_msg() semantics unchanged for older callers.
No functional change intended.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The purpose of a GPU reset is to make sure that fence can be signaled
again and the signal and resume workers can make progress again.
So waiting for the resume worker or any fence in the GPU reset path is
just utterly nonsense.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add pinctrl support for the SoC0 instance of the ASPEED AST2700.
AST2700 consists of two interconnected SoC instances, each with its own
pinctrl register block.
The SoC0 pinctrl hardware closely follows the design found in previous
ASPEED BMC generations, allowing the driver to build upon the common
ASPEED pinctrl infrastructure.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
Add a device tree binding for the pin controller found in the
ASPEED AST2700 SoC0.
The controller manages various peripheral functions such as eMMC, USB,
VGA DDC, JTAG, and PCIe root complex signals.
Describe the AST2700 SoC0 pin controller using standard pin multiplexing
and configuration properties.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
pinctrl_gpio_direction_input() / pinctrl_gpio_direction_output() take
the pinctrl mutex. This causes a gpiochip operations to need to sleep.
Worse yet, the .can_sleep field in the gpiochip is not set. This causes
the shared GPIO proxy to trip over, as it uses gpiod_cansleep() to check
whether it can use a spinlock or needs a mutex. In this case, it ends
up taking a spinlock, then calls pinctrl_gpio_direction_output(), which
takes a mutex. This causes a huge warning.
Since the Mediatek hardware has separate clear/set registers, there is
no risk of clobbering other bits like with a read-modify-write pattern.
Also, once the GPIO function is selected / muxed in, further GPIO
operations do not involve pinctrl operations or state. The GPIO direction
and level values do not require toggling the pinmux or any other pin config
options.
Switch to directly calling mtk_pmx_gpio_set_direction() in the GPIO set
direction callbacks to avoid taking the pinctrl mutex. Drop the
.gpio_set_direction field in mtk_pmx_ops to signal we are no longer using
the pinctrl GPIO layer for setting the direction.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
pinctrl_gpio_direction_input() / pinctrl_gpio_direction_output() take
the pinctrl mutex. This causes a gpiochip operations to need to sleep.
Worse yet, the .can_sleep field in the gpiochip is not set. This causes
the shared GPIO proxy to trip over, as it uses gpiod_cansleep() to check
whether it can use a spinlock or needs a mutex. In this case, it ends
up taking a spinlock, then calls pinctrl_gpio_direction_output(), which
takes a mutex. This causes a huge warning.
While this class of Mediatek hardware does not have separate clear/set
registers, the pinctrl context has a spinlock that is taken whenever
a register read-modify-write is done. Also, once the GPIO function is
selected / muxed in, further GPIO operations do not involve pinctrl
operations or state. The GPIO direction and level values do not require
toggling the pinmux or any other pin config options.
Switch to directly calling mtk_pinmux_gpio_set_direction() in the GPIO
set direction callbacks to avoid taking the pinctrl mutex. Drop the
.gpio_set_direction field in mtk_pmxops to signal we are no longer using
the pinctrl GPIO layer for setting the direction.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
Bump `KFD_IOCTL_MINOR_VERSION` from 22 to 23 and document version 1.23
in `kfd_ioctl.h` so userspace can detect profiler ioctl support.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix this by skipping the sysfs disable mapping when the GPU is
currently undergoing a reset or suspend flow.
Additionally, add debug logging in psp_ptl_invoke() to better
trace PTL state and format queries/updates cmd.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
During RAS UE-triggered GPU reset, gfx_v9_4_3_hw_fini() attempts to
send a PTL disable command to PSP. Since PSP is unresponsive at that
point, this produces spurious error logs on all hive nodes:
PTL command 0xa0000001 failed, PSP response status: 0xFFFFFFFF
PTL initialization failed (-5)
Skip the PTL disable command when GPU reset is in progress, as PTL
will be properly re-initialized during post-reset recovery via
gfx_v9_4_3_late_init().
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Only set the bit when PTL is actually being disabled (state=0)
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Downgrade unhalt_cpsch warning to dev_dbg when sched is already stopped
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Create PTL sysfs in xgmi_reset_on_init restore path for MINIMAL_XGMI
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move amdgpu_amdkfd_stop/start_sched calls from kfd_ptl_control()
into amdgpu_ptl_perf_monitor_ctrl() so all PTL callers (KFD ioctl,
sysfs, GFX init) get consistent scheduling management.
Add amdgpu_amdkfd_stop/start_sched_all() wrappers to stop and
restart KFD scheduling on all nodes without assuming node ID ordering.
v3:
* call start/stop for PTL Set Only
v2:
* move the stop/start sched function to
amdgpu_ptl_perf_monitor_ctrl(Lijo)
* add wrapper amdgpu_amdkfd_stop_sched_all and
amdgpu_amdkfd_start_sched_all (Lijo)
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GC 9.4.4 uses SPI busy status for idle detection instead of GRBM GUI_ACTIVE.
Add version check to use SPI_BUSY for 9.4.4 while keeping GRBM_STATUS
GUI_ACTIVE check for other GC versions.
v2: move this check into amdgpu_ptl_perf_monitor_ctrl(Lijo)
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add an explicit check on cmd->resp.status after psp_cmd_submit_buf()
returns to ensure PTL state is only updated on actual success.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Ensure GFX engine is idle before switching PTL state to prevent
register access violations and CP hang. This addresses the race
condition where in-flight GPU commands could conflict with PTL
state changes.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add F8 and VECTOR to amdgpu_ptl_fmt and PSP format mapping.
Update PTL format strings and GFX format enum to keep PSP/KFD in sync.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add a new kernel module parameter 'amdgpu.ptl' to allow
users to enable or disable PTL feature at driver loading time.
Parameter values:
*) 0 or -1: disable PTL (default)
*) 1: enable PTL
*) 2: permanently disable PTL
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use a bitmap to track PTL disable requests from sysfs and profiler.
PTL is only re-enabled once all sources have released their disable
requests, avoiding premature enablement.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Stop the scheduler before releasing the PTL disable request to ensure
the GPU is quiescent during the PTL state transition. This prevents
potential queue preemption failures and GPU resets caused by modifying
PTL state while waves are executing
v1->v2:
only stop/start the scheduler when the PTL state actually needs to transition(Yifan)
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Introduce a new IOCTL option to allow userspace explicit control over
the Peak Tops Limiter (PTL) state for profiling
Link: https://github.com/ROCm/rocm-systems/tree/develop/projects/rocprofiler-sdk
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add per-GPU sysfs files under /sys/class/drm/cardX/device/ptl to
control the Peak Tops Limiter (PTL) feature. Exposes ptl_enable
(enable/disable PTL), ptl_format (set/query preferred formats),
and ptl_supported_formats (list supported formats)
Example usage
-------------
Query PTL status:
`cat /sys/class/drm/card1/device/ptl/ptl_enable`
Enable PTL:
`sudo bash -c "echo 1 > /sys/class/drm/card1/device/ptl/ptl_enable"`
Disable PTL:
`sudo bash -c "echo 0 > /sys/class/drm/card1/device/ptl/ptl_enable"`
Set PTL preferred formats:
`sudo bash -c "echo I8,F32 > /sys/class/drm/card1/device/ptl/ptl_format"`
Query supported formats:
`cat /sys/class/drm/card1/device/ptl/ptl_supported_formats`
v3 changes:
* move N/A to previous format in format show(Alex)
* fix format check for format store(Alex)
* drop the ptl declarations into amdgpu_ptl.h(Alex)
v2 changes:
* add usage commands in commit info (Alex)
* move amdgpu_ptl_fmt into kgd_kfd_interface.h (Alex)
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
interface
The PTL (Peak Tops Limiter) feature exposes per-GPU sysfs files under
/sys/class/drm/cardX/device/ptl/ to allow users to enable or disable PTL,
configure preferred data formats, and query supported formats. The usage
of these sysfs files is not always obvious, so add documentation to
describe their purpose and provide concrete usage examples.
V3 changes:
* format show will display preferred formats instead of N/A (Alex)
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add kgd->ptl_ctrl() callback so KFD can query/enable/disable
PTL state through the PSP performance monitor interface.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Introduce hardware detection, runtime state tracking and a
kgd->ptl_ctrl() callback to enable/disable/query PTL via the
PSP performance-monitor interface (commands 0xA0000000/1).
The driver now exposes PTL capability to KFD and keeps the
software state in sync with the hardware.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Introduce a Peak Tops Limiter (PTL) driver that dynamically caps
engine frequency to ensure delivered TOPS never exceeds a defined
TOPS_limit. This initial implementation provides core data structures
and kernel-space interfaces (set/get, enable/disable) to manage PTL state.
PTL performs a firmware handshake to initialize its state and update
predefined format types. It supports updating these format types at
runtime while user-space tools automatically switch PTL state, and
also allows explicitly switching PTL state via newly added commands.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Introduce new psp interfaces and structures for performance
monitoring hardware control.
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
kfd_ioctl_profiler takes a similar approach to that of
kfd_ioctl_dbg_trap (which contains debugger related IOCTL
services) where kfd_ioctl_profiler will contain all profiler
related IOCTL services. The IOCTL is designed to be expanded
as needed to support additional profiler functionality.
The current functionality of the IOCTL is to allow for profilers
which need PMC counters from GPU devices to both signal to other
profilers that may be on the system that the device has active PMC
profiling taking place on it (multiple PMC profilers on the same
device can result in corrupted counter data) and to setup the device
to allow for the collection of SQ PMC data on all queues on the device.
For PMC data for the SQ block (such as SQ_WAVES) to be available
to a profiler, mmPERFCOUNT_ENABLE must be set on the queues. When
profiling a single process, the profiler can inject PM4 packets into
each queue to turn on PERFCOUNT_ENABLE. When profiling system wide,
the profiler does not have this option and must have a way to turn
on profiling for queues in which it cannot inject packets into directly.
Accomplishing this requires a few steps:
1. Checking if the user has the necessary permissions to profile system
wide on the device. This check uses the same check that linux perf
uses to determine if a user has the necessary permissions to profile
at this scope (primarily if the process has CAP_SYS_PERFMON or is root).
2. Locking the device for profiling. This is done by setting a lock bit
on the device struct and storing the process that locked the device.
3. Iterating all queues on the device and issuing an MQD Update to enable
perfcounting on the queues.
4. Actions to cleanup if the process exits or releases the lock.
The IOCTL also contains a link to the existing PC Sampling IOCTL as well.
This is per a suggestion that we should potentially remove the PC Sampling
IOCTL to have it be a part of the profiler IOCTL. This is a future change.
In addition, we do expect to expand the profiler IOCTL to include
additional profiler functionality in the future (which necessitates the
use of a version number).
v2: sqaush in proper IOCTL number
Proposed userpace support:
https://github.com/ROCm/rocm-systems/commit/40abc95a6463a61bb318a67efd6d9cc3e5ee8839
Signed-off-by: Benjamin Welton <benjamin.welton@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Acked-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
fwnode_init()
If a firmware node is allocated on the stack (for instance: temporary
software node whose life-time we control) or on the heap - but using a
non-zeroing allocation function - and initialized using fwnode_init(),
its secondary pointer will contain uninitialized memory which likely
will be neither NULL nor IS_ERR() and so may end up being dereferenced
(for example: in dev_to_swnode()). Set fwnode->secondary to NULL on
initialization. While at it: initialize the remaining fields of struct
fwnode_handle too just to be sure.
Cc: stable@vger.kernel.org
Fixes: 01bb86b380a3 ("driver core: Add fwnode_init()")
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260511074927.9473-1-bartosz.golaszewski@oss.qualcomm.com
[ Fix typo in commit message. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
The old format to define pinctrl settings for imx in DT has two hierarchy
levels. The first level are function device nodes. The second level are
pingroups which contain a property fsl,pins. The original ntention was to
define all pin functions in a single dtsi file and just reference the
correct ones in the board files.
The commit ("5fcdf6a7ed95e pinctrl: imx: Allow parsing DT without function
nodes") already make moden i.MX chip support flatten layout.
Make legacy chipes (more than 15 years) support this flatten layout also.
Fixes: e948cbdc41d6f ("ARM: dts: imx: remove redundant intermediate node in pinmux hierarchy")
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
The tryget_task_struct() calls in scx_sub_disable(),
scx_root_enable_workfn() and scx_sub_enable_workfn() can never fail at
the points they're invoked:
- scx_root_enable_workfn() iterates over scx_tasks under scx_tasks_lock
and rq lock. sched_ext_dead() removes tasks from scx_tasks under the
same scx_tasks_lock before put_task_struct_rcu_user() runs in
finish_task_switch(). So any task observed in scx_tasks must have
usage > 0; put_task_struct_rcu_user() hasn't been called and the
delayed_put_task_struct() callback that decrements usage cannot have
been queued.
- scx_sub_disable() and scx_sub_enable_workfn() iterate via
css_task_iter, which takes a reference on each task in
css_task_iter_next() and holds it until the next iter_next() call, so
usage > 0 is guaranteed by the iter itself.
The actual filter for dead tasks is the SCX_TASK_DEAD check inside
scx_task_iter_next_locked(), not tryget; tryget only fails on zero
usage, a state that can't be reached for tasks visible to these iters.
Commit b7d4b28db7da ("sched_ext: Use SCX_TASK_READY test instead of
tryget_task_struct() during class switch") removed an analogous tryget
in the class-switch loop. Convert the remaining tryget calls to plain
get_task_struct() and update the comment in scx_root_enable_workfn()
that suggested tasks could be observed with zero @usage waiting for an
RCU grace period.
Link: https://lore.kernel.org/all/agCLBxHEUqWIepx8@google.com
Suggested-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The benchmark drives the workqueue's affinity_scope through sysfs by
filp_open()'ing /sys/bus/workqueue/devices/bench_wq/affinity_scope. When
CONFIG_TEST_WORKQUEUE=y, the module_init runs during kernel init before
userspace has mounted sysfs, so every open returns -ENOENT and the
benchmark loop spins emitting:
test_workqueue: open /sys/bus/workqueue/devices/bench_wq/affinity_scope failed: -2
Mirror the TEST_BPF pattern and add "depends on m" so Kconfig will not
let this be built into the kernel image, and document the reason in the
help text.
Fixes: 24b2e73f9700 ("workqueue: add test_workqueue benchmark module")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The apply_wqattrs_lock()/unlock() helpers were introduced by
commit a0111cf6710b ("workqueue: separate out and refactor the locking
of applying attrs") to encapsulate the get_online_cpus() (later
cpus_read_lock()) + mutex_lock(&wq_pool_mutex) acquire pair that was
duplicated across the apply-attrs paths.
Since commit 19af45757383 ("workqueue: Remove cpus_read_lock() from
apply_wqattrs_lock()") removed the cpus_read_lock() (pwq creation and
installation now operate on wq_online_cpumask, so CPU hotplug no longer
needs to be excluded), the wrappers have been one-line forwarders to
mutex_lock(&wq_pool_mutex)/mutex_unlock(&wq_pool_mutex).
They no longer encode any non-trivial locking rule and obscure the fact
that callers just take the existing wq_pool_mutex. This align with the
"unnecessary" helpers that got discussed in [1]
Inline the eight call sites and remove the wrappers. No functional
change.
Link: https://lore.kernel.org/all/afs_44-6ToJJVZTn@gmail.com/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
When decoding osd_state and osd_weight from an incoming osdmap in
osdmap_decode(), both are decoded for each osd, i.e., map->max_osd
times. The ceph_decode_need() check only accounts for
sizeof(*map->osd_weight) once. This can potentially result in an
out-of-bounds memory access if the incoming message is corrupted such
that the max_osd value exceeds the actual content of the osdmap message.
This patch fixes the issue by changing the corresponding part in the
ceph_decode_need() check to account for
map->max_osd*sizeof(*map->osd_weight).
Cc: stable@vger.kernel.org
Fixes: dcbc919a5dc8 ("libceph: switch osdmap decoding to use ceph_decode_entity_addr")
Signed-off-by: Raphael Zimmer <raphael.zimmer@tu-ilmenau.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
This venerable comment got detached from its context when the code moved
in commit 394158559d4c ("x86: move all the pgd_list handling to one
place"). Put it back next to its context. It was originally on
pgd_list_add() but it actually describes pgd_list so put it there.
While moving it, update it to strip away stale and superfluous info.
pageattr.c doesn't exist any more. pgd_list is now required
for all x86 architectures. Also be slightly more precise about what PGDs
are in this list.
[ dhansen: tweak and trim the updated comment a bit ]
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://patch.msgid.link/20260323-pgd_list-comment-v2-1-77ccf2dc77e8@google.com
|
|
delegate_tool
delegate_tool was missing the delegate overrides for schedstat_cpu
and schedstat_domain. As a result, when allocated with zalloc, these
callbacks defaulted to NULL, causing a segmentation fault crash if
any schedstat events were delivered during event processing.
Fix this by adding delegate_schedstat_cpu and delegate_schedstat_domain
via the CREATE_DELEGATE_OP2 macro, and ensuring delegate_tool__init
correctly registers them.
Additionally, delegate_tool__init completely omitted copying the
dont_split_sample_group property from the delegate. This would cause
wrapper tools to default the flag to false, which corrupts piped event
processing (e.g., in perf inject) by triggering duplicate event
deliveries on split sample values in deliver_sample_group().
Similarly, perf_tool__init() omitted the initialization of this
boolean field. On stack-allocated tools that rely on this initializer
(like intel-tpebs or __cmd_evlist), this could result in uninitialized
stack garbage evaluating to true—silently dropping non-leader event
members in deliver_sample_group().
Fix both issues by properly copying the field in delegate_tool__init
and initializing it to false in perf_tool__init.
Fixes: 6331b266935916bf ("perf tool: Add a delegate_tool that just delegates actions to another tool")
Fixes: 79bcd34e0f3da39f ("perf inject: Fix leader sampling inserting additional samples")
Assisted-by: Gemini-CLI:Google Gemini 3
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Gabriel Marin <gmx@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
perf_sched__timehist() registers event handlers for options using the
sched->tool struct. It registers handlers for MMAP, COMM, EXIT, FORK, etc.
but completely omits registering a handler for MMAP2 events.
Failing to register both MMAP and MMAP2 handlers causes modern systems
(which primarily output MMAP2 records) to silently drop VMA map mappings.
This results in uninitialized machine/thread mapping structures, making it
impossible to resolve shared library instruction pointers (IPs) to dynamic
symbols/DSOs during timehist callchain analysis.
Fix this by correctly registering perf_event__process_mmap2 in
sched->tool inside perf_sched__timehist().
Fixes: 49394a2a24c78ce0 ("perf sched timehist: Introduce timehist command")
Assisted-by: Gemini-CLI:Google Gemini 3
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Gabriel Marin <gmx@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The receiver shutdown timer handler, batadv_tp_receiver_shutdown(), is
responsible for releasing the tp_vars reference it holds. However, the
existing logic for coordinating this release with batadv_tp_stop_all() was
flawed.
timer_shutdown_sync() guarantees the timer will not fire again after it
returns, but it returns non-zero only when the timer was pending at the
time of the call. If the timer had already expired (and
batadv_tp_stop_all() would unsucessfully try to rearm itself),
batadv_tp_stop_all() skips its batadv_tp_vars_put(), and
batadv_tp_receiver_shutdown() fails to put its own reference as well.
Fix this by introducing a new atomic variable receiving that is set to 1
when the receiver is initialized and cleared atomically with atomic_xchg()
by whichever side claims it first. Only the side that observes the
transition from 1 to 0 is responsible for releasing the tp_vars timer
reference, eliminating the uncertainty.
Cc: stable@kernel.org
Fixes: 3d3cf6a7314a ("batman-adv: stop tp_meter sessions during mesh teardown")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
|
batadv_tp_sender_shutdown() unconditionally decrements the "sending"
atomic counter. If multiple paths (e.g. timeout, user cancel, and
normal finish) call this function, the counter can underflow to -1.
Since the sender logic treats any non-zero value as "still sending",
a negative value causes the sender kthread to loop indefinitely.
This leads to a use-after-free when the interface is removed while
the zombie thread is still active.
Fix this by using atomic_xchg() to ensure the counter only transitions
from 1 to 0 once.
Fixes: 33a3bb4a3345 ("batman-adv: throughput meter implementation")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Luxiao Xu <rakukuip@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
[sven: added missing change in batadv_tp_send]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
|
in diff mode
The patch addresses multiple segmentation fault vectors, out-of-bounds
reads, and memory leaks in perf sched stats by adding bounds checks,
NULL checks, proper error propagation, and robust memory cleanup.
1. In get_all_cpu_stats(), added assert(!list_empty(head)) to prevent
unsafe list_first_entry() calls on empty lists, added a missing NULL
check for summary_head->cpu_data allocation, and implemented a cleanup
ladder using a temporary list to prevent memory leaks on error paths.
2. In free_schedstat(), fixed memory leaks by ensuring internal domain_data
and cpu_data pointers are freed.
3. In show_schedstat_data(), fixed a stale pointer issue where ds2 retained
its value from a previous iteration when dptr2 became NULL, and added
proper propagation of errors from get_all_cpu_stats().
4. Propagated show_schedstat_data() errors up to perf_sched__schedstat_diff()
and perf_sched__schedstat_live() to prevent output corruption on failure.
5. In show_schedstat_data(), added NULL checks for cd_map1 and cd_map2
to gracefully handle invalid or empty data files.
6. Added parallel iteration termination checks using list_is_last() in
show_schedstat_data() for both domain and CPU lists to safely terminate
at the end of each list when files contain a different number of CPUs
or domains.
7. Added CPU bounds checks (cs1->cpu >= nr1 and cs2->cpu >= nr2) in
show_schedstat_data() to prevent out-of-bounds reads from cd_map1 and
cd_map2 when comparing files from machines with different CPU counts.
8. Added NULL checks for cd_info1 and cd_info2 to prevent crashes when
a CPU has data samples but no corresponding domain info in the header.
9. Added domain bounds checks (ds1->domain >= cd_info1->nr_domains and
ds2->domain >= cd_info2->nr_domains) to prevent out-of-bounds array
accesses in the domains array.
10. Added NULL checks for dinfo1 and dinfo2 in show_schedstat_data()
to prevent crashes when a domain has no corresponding domain info.
11. Zero-initialized the perf_data array in perf_sched__schedstat_diff()
to prevent stack garbage from causing perf_data_file__fd() to attempt
to use a NULL fptr when use_stdio happened to be non-zero.
Assisted-by: Gemini:gemini-3.1-pro-preview
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Athira Rajeev <atrajeev@linux.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The trace summary test calls /bin/true and filters for open, read and
close events. These events are coming from shared library loads.
On a musl system, the loader and libc may point to the same file. true
needs only libc, no further shared libraries are loaded at startup. The
test fails since no open, read and close events are captured.
root@host:~# ldd /bin/true
/lib/ld-musl-riscv64.so.1 (0x3fb8882000)
libc.so => /lib/ld-musl-riscv64.so.1 (0x3fb8882000)
root@host:~# file /lib/ld-musl-riscv64.so.1
/lib/ld-musl-riscv64.so.1: symbolic link to /usr/lib/libc.so
root@host:~# strace -f /bin/true
execve("/bin/true", ["/bin/true", ...], ... /* 18 vars */) = 1
set_tid_address(0x3fa1f7bf70) = 330
mprotect(0x2ad6b8e000, 12288, PROT_READ) = 0
exit_group(0) = ?
+++ exited with 0 +++
Run "cat /dev/null" instead of "true". This creates the required events
regardless of the C library and it works for cat from busybox or from
coreutils.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The "syscalls:sys_enter_openat event fields" test calls
openat(AT_FDCWD, "/etc/passwd", O_RDONLY | O_DIRECTORY)
and verifies that the flags of the captured event are matching.
This fails for musl, where the openat syscall wrapper always adds
O_LARGEFILE.
Update the check to allow for additional flags, the access mode flags
must be unchanged.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The perf ftrace test case runs:
perf ftrace profile --graph-opts depth=5 sleep 0.1
and checks that the output contains a *clock_nanosleep function with a
count of 1.
This fails on a risc-v system that uses musl as its C library. musl's
nanosleep syscall wrapper uses either the nanosleep or the
clock_nanosleep syscall.
Filter for sys_*nanosleep to allow both syscalls.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
io_uring_try_cancel_requests() dropped ctx->uring_lock before calling
io_kill_timeouts(), which walks each timeout's link chain via
io_match_task() to test REQ_F_INFLIGHT. With chain mutation now
serialized by ctx->uring_lock, that walk needs the lock too.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
io_link_timeout_fn() is the hrtimer callback that fires when a linked
timeout expires. It currently calls io_remove_next_linked(prev) under
ctx->timeout_lock to splice the timeout request out of the link chain.
This is the only chain-mutation site that runs without ctx->uring_lock,
because hrtimer callbacks cannot take a mutex. Defer the splicing until
the task_work callback.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
io_wq_free_work() calls io_req_find_next() from io-wq worker context,
which reads and clears req->link without holding any lock. This can
potentially race with other paths that mutate the same chain under
ctx->uring_lock.
Take ctx->uring_lock around the io_req_find_next() call. Only requests
with IO_REQ_LINK_FLAGS reach this path, which is not the hot path.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When a controller connects, nvme_start_ctrl() emits the
"NVME_EVENT=connected" uevent and sets the NVME_CTRL_STARTED_ONCE flag.
Currently, the uevent is emitted before the flag is set. This creates a
race condition for userspace tools (like udev rules) that might rely on
the "connected" event to configure other attributes.
Swap the order of operations in nvme_start_ctrl() so that the
NVME_CTRL_STARTED_ONCE flag is set before the uevent is sent. This
guarantees that the admin_timeout can already be changed when userspace
is notified.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Use a flexible array member (FAM) to combine hwmods array allocation
with the omap_device structure. This reduces the number of allocations
from two separate calls (one for the device, one for the array) to a
single allocation, improving efficiency and reducing memory fragmentation.
The FAM approach also enables bounds checking through __counted_by(),
which provides runtime verification that array accesses stay within
the allocated size. This improves security and helps catch bugs during
development.
Simplify error handling by removing the unnecessary multi-label goto
pattern. The new code is more straightforward: allocate, verify, copy
data, and either return success or error immediately.
Also removes the now-redundant kfree(od->hwmods) in omap_device_delete()
since the hwmods array is now embedded in the structure rather than
separately allocated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20260330213528.18187-1-rosenp@gmail.com
Signed-off-by: Kevin Hilman (TI) <khilman@baylibre.com>
|
|
Since every platform driver can be forced to match a device that doesn't
match its list of device IDs because of device_match_driver_override(),
platform drivers that rely on the existence of a device's ACPI companion
object should verify its presence.
Accordingly, add requisite ACPI_COMPANION() or ACPI_HANDLE() checks
against NULL to 13 platform drivers handling core ACPI devices.
Also change the value returned by the ACPI thermal zone driver when
the device's ACPI companion is not present to -ENODEV for consistency
with the other drivers.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/4516068.ejJDZkT8p0@rafael.j.wysocki
Cc: 7.0+ <stable@vger.kernel.org> # 7.0+
|
