| Age | Commit message (Collapse) | Author |
|---|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add two mainboards for the TQ-Systems TQMLS1028A SoM, based on the NXP
Layerscape LS1028A.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device trees for the MBLS1028A and the MBLS1028A-IND and the SoM
TQMLS1028A.
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When DSC is enabled on a pipe, the pipe pixel rate input to the
CDCLK frequency and pipe joining calculation needs an adjustment to
account for compression overhead "bubbles" added at each horizontal
slice boundary.
Account for this overhead while computing min cdclk required for DSC.
v2:
- Get rid of the scaling factor and return unchanged pixel-rate
instead of 0.
v3:
- Use mul_u32_u32() for the bubble-adjusted pixel rate to avoid 64x64
multiplication and drop redundant casts in DIV_ROUND_UP_ULL(). (Imre)
Bspec:68912
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20251223150826.2591182-1-ankit.k.nautiyal@intel.com
|
|
Add an overlay of expansion board (PEB-AV-10) that supports multimedia
interfaces, 3.5mm headphone jack, a USB-A port and LVDS, backlight
connectors can be connected to the imx8mp libra. Audio works when no
display is connected to expansion board.
A separate overlay for Powertip display, based on peb-av-10.dtsi and
intended for use with PEB-AV-10 expansion board, will be added
later as display support is not yet available.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add imx8mp-libra-rdk-fpsc-lvds-ph128800t006-zhc01.dtso
devicetree display overlay for the i.MX8MP Libra RDK platform.
The overlay enable LVDS display configuration.
To keep the consistent style of panel and backlight nodes and labels.
They are updated in imx8mp-libra base board devicetree and
etml1010g3dra display overlay.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ENETC instance 1~3, EMDIO and PTP Timer 0~1 support.
The EMDIO provides MDIO bus for ENETCs to access their external PHYs.
The PTP Timer provides current time with nanosecond resolution, precise
periodic pulse, pulse on timeout, and time capture on external pulse
support. It also provides PTP clock for ENETCs to implement time
synchronization as required for IEEE 1588 and IEEE 802.1AS-2020.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The NETC related nodes for i.MX94, this NETC has two PCIe buses, the bus
0 has 1 ENETC instance, one PTP timer, one RCEC and a switch, currently,
the switch is not added due to the DT binding and the driver is not
ready at the moment. The bus 1 has three ENETC instances, 2 PTP timers,
1 RCEC and one EMDIO.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8DXL
Add DB pmu related nodes. This pmu is in DB (system interconnects).
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ddr perf monitor device node for i.MX8QM. Change imx8-ss-ddr.dtsi's
compatible string to fsl,imx8qxp-ddr-pmu. i.MX8QM overwrite to
fsl,imx8qm-ddr-pmu. All fallback to fsl,imx8-ddr-pmu.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- Fix uninitialized @ret on alloc_percpu() failure leading to
ERR_PTR(0)
- Fix PREEMPT_RT warning when bypass load balancer sends IPI to offline
CPU by using resched_cpu() instead of resched_curr()
- Fix comment referring to renamed function
- Update scx_show_state.py for scx_root and scx_aborting changes
* tag 'sched_ext-for-6.19-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
tools/sched_ext: update scx_show_state.py for scx_aborting change
tools/sched_ext: fix scx_show_state.py for scx_root change
sched_ext: Use the resched_cpu() to replace resched_curr() in the bypass_lb_node()
sched_ext: Fix some comments in ext.c
sched_ext: fix uninitialized ret on alloc_percpu() failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
- Fix a spurious cpuset warning when disabling remote partition after
CPU hotplug leaves subpartitions_cpus empty. Guard the warning and
invalidate affected partitions.
* tag 'cgroup-for-6.19-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: fix warning when disabling remote partition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix UAF in seqiv
- Fix regression in hisilicon
* tag 'v6.19-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon/qm - fix incorrect judgment in qm_get_complete_eqe_num()
crypto: seqiv - Do not use req->iv after crypto_aead_encrypt
|
|
Now that drbg_get_random_bytes() always returns 0, checking its result at
the call sites stopped to make sense -- make this function return *void*
instead of *int*...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently, drbg_fips_continuous_test() only returns 0 and -EAGAIN, so an
early return from the *do*/*while* loop in drbg_get_random_bytes() just
isn't possible. Make drbg_fips_continuous_test() return bool instead of
*int* (using true instead of 0 and false instead of -EAGAIN). This way,
we can further simplify drbg_get_random_bytes()...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In drbg_fips_continuous_test(), not only the initializer of the ret local
variable is useless, the variable itself does not seem needed as it only
stores the result of memcmp() until it's checked on the next line -- get
rid of the variable...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Return the result of calling crypto_register_alg() directly and remove
the local return variable.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Replace sprintf() with sysfs_emit() in sso_pf_func_ovrd_show() and
kvf_limits_show(). sysfs_emit() is preferred for formatting sysfs output
as it performs proper bounds checking. No functional changes.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Replace sprintf() with sysfs_emit() in verify_compress_show() and
sync_mode_show(). sysfs_emit() is preferred to format sysfs output as it
provides better bounds checking. No functional changes.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Kanchana P Sridhar <kanchana.p.sridhar@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The restarting message from PF to VF is sent twice during AER error
handling: once from adf_error_detected() and again from
adf_disable_sriov().
This causes userspace subservices to shutdown unexpectedly when they
receive a duplicate restarting message after already being restarted.
Avoid calling adf_pf2vf_notify_restarting() and
adf_pf2vf_wait_for_restarting_complete() from adf_error_detected() so
that the restarting msg is sent only once from PF to VF.
Fixes: 9567d3dc760931 ("crypto: qat - improve aer error reset handling")
Signed-off-by: Harshita Bhilwaria <harshita.bhilwaria@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Ravikumar PM <ravikumar.pm@intel.com>
Reviewed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
io_uring manages issued and pending IOPOLL read/write requests in a
singly linked list. One downside of that is that individual items
cannot easily be removed from that list, and as a result, io_uring
will only complete a completed request N in that list if 0..N-1 are
also complete. For homogenous IO this isn't necessarily an issue,
but if different devices are involved in polling in the same ring, or
if disparate IO from the same device is being polled for, this can
defer completion of some requests unnecessarily.
Move to a doubly linked list for iopoll completions instead, making it
possible to easily complete whatever requests that were polled done
successfully.
Co-developed-by: Fengnan Chang <fengnanchang@gmail.com>
Link: https://lore.kernel.org/io-uring/20251210085501.84261-1-changfengnan@bytedance.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Replace simple_strtol() with the recommended kstrtoul() for parsing the
'ramdisk_size=' boot parameter. Unlike simple_strtol(), which returns a
long, kstrtoul() converts the string directly to an unsigned long and
avoids implicit casting.
Check the return value of kstrtoul() and reject invalid values. This
adds error handling while preserving behavior for existing values, and
removes use of the deprecated simple_strtol() helper. The current code
silently sets 'rd_size = 0' if parsing fails, instead of leaving the
default value (CONFIG_BLK_DEV_RAM_SIZE) unchanged.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
C-String literals were added in Rust 1.77. Replace instances of
`kernel::c_str!` with C-String literals where possible.
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
|
|
Initialize the eb.vma array with values of 0 when the eb structure is
first set up. In particular, this sets the eb->vma[i].vma pointers to
NULL, simplifying cleanup and getting rid of the bug described below.
During the execution of eb_lookup_vmas(), the eb->vma array is
successively filled up with struct eb_vma objects. This process includes
calling eb_add_vma(), which might fail; however, even in the event of
failure, eb->vma[i].vma is set for the currently processed buffer.
If eb_add_vma() fails, eb_lookup_vmas() returns with an error, which
prompts a call to eb_release_vmas() to clean up the mess. Since
eb_lookup_vmas() might fail during processing any (possibly not first)
buffer, eb_release_vmas() checks whether a buffer's vma is NULL to know
at what point did the lookup function fail.
In eb_lookup_vmas(), eb->vma[i].vma is set to NULL if either the helper
function eb_lookup_vma() or eb_validate_vma() fails. eb->vma[i+1].vma is
set to NULL in case i915_gem_object_userptr_submit_init() fails; the
current one needs to be cleaned up by eb_release_vmas() at this point,
so the next one is set. If eb_add_vma() fails, neither the current nor
the next vma is set to NULL, which is a source of a NULL deref bug
described in the issue linked in the Closes tag.
When entering eb_lookup_vmas(), the vma pointers are set to the slab
poison value, instead of NULL. This doesn't matter for the actual
lookup, since it gets overwritten anyway, however the eb_release_vmas()
function only recognizes NULL as the stopping value, hence the pointers
are being set to NULL as they go in case of intermediate failure. This
patch changes the approach to filling them all with NULL at the start
instead, rather than handling that manually during failure.
Reported-by: Gangmin Kim <km.kim1503@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/15062
Fixes: 544460c33821 ("drm/i915: Multi-BB execbuf")
Cc: stable@vger.kernel.org # 5.16.x
Signed-off-by: Krzysztof Niemiec <krzysztof.niemiec@intel.com>
Reviewed-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20251216180900.54294-2-krzysztof.niemiec@intel.com
|
|
migf->filp is accessed after migf has been freed. Save the error
value before calling kfree() to prevent use-after-free.
Fixes: 1f5556ec8b9e ("vfio/xe: Add device specific vfio_pci driver variant for Intel graphics")
Signed-off-by: Alper Ak <alperyasinak1@gmail.com>
Link: https://lore.kernel.org/r/20251225151349.360870-1-alperyasinak1@gmail.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
pds_vfio_dirty_enable() allocates memory for region_info. If
interval_tree_iter_first() returns NULL, the function returns -EINVAL
immediately without freeing the allocated memory, causing a memory leak.
Fix this by jumping to the out_free_region_info label to ensure
region_info is freed.
Fixes: 2e7c6feb4ef52 ("vfio/pds: Add multi-region support")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Link: https://lore.kernel.org/r/20251225143150.1117366-1-zilin@seu.edu.cn
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes, and bunch of reverts for 6.19-rc3.
Included in here are:
- reverts of some typec ucsi driver changes that had a lot of
regression reports after -rc1. Let's just revert it all for now and
it will come back in a way that is better tested.
- other typec bugfixes
- usb-storage quirk fixups
- dwc3 driver fix
- other minor USB fixes for reported problems.
All of these have passed 0-day testing and individual testing"
* tag 'usb-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
Revert "usb: typec: ucsi: Update UCSI structure to have message in and message out fields"
Revert "usb: typec: ucsi: Add support for message out data structure"
Revert "usb: typec: ucsi: Enable debugfs for message_out data structure"
Revert "usb: typec: ucsi: Add support for SET_PDOS command"
Revert "usb: typec: ucsi: Fix null pointer dereference in ucsi_sync_control_common"
Revert "usb: typec: ucsi: Get connector status after enable notifications"
usb: ohci-nxp: clean up probe error labels
usb: gadget: lpc32xx_udc: clean up probe error labels
usb: ohci-nxp: fix device leak on probe failure
usb: phy: isp1301: fix non-OF device reference imbalance
usb: gadget: lpc32xx_udc: fix clock imbalance in error path
usb: typec: ucsi: Get connector status after enable notifications
usb: usb-storage: Maintain minimal modifications to the bcdDevice range.
usb: dwc3: of-simple: fix clock resource leak in dwc3_of_simple_probe
usb: typec: ucsi: Fix null pointer dereference in ucsi_sync_control_common
USB: lpc32xx_udc: Fix error handling in probe
usb: typec: altmodes/displayport: Drop the device reference in dp_altmode_probe()
usb: phy: fsl-usb: Fix use-after-free in delayed work during device removal
usb: renesas_usbhs: Fix a resource leak in usbhs_pipe_malloc()
usb: typec: ucsi: huawei-gaokin: add DRM dependency
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are some small serial driver fixes for some reported issues.
Included in here are:
- serial sysfs fwnode fix that was much reported
- sh-sci driver fix
- serial device init bugfix
- 8250 bugfix
- xilinx_uartps bugfix
All of these have passed 0-day testing and individual testing"
* tag 'tty-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: xilinx_uartps: fix rs485 delay_rts_after_send
serial: sh-sci: Check that the DMA cookie is valid
serial: core: Fix serial device initialization
serial: 8250: longson: Fix NULL vs IS_ERR() bug in probe
serial: core: Restore sysfs fwnode information
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Takashi Sakamoto:
"A fix for PCI driver for Texas Instruments PCILyx series.
The driver had a bug where it allocated a DMA-coherent buffer of 16 KB
but released it using PAGE_SIZE. This disproportion was reported in
2020, but the fix was never merged. It is finally resolved"
* tag 'firewire-fixes-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: nosy: Fix dma_free_coherent() size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"Nothing exotic here; these are the cleanup and new ISA extension
probing patches (not including CFI):
- Add probing and userspace reporting support for the standard RISC-V
ISA extensions Zilsd and Zclsd, which implement load/store dual
instructions on RV32
- Abstract the register saving code in setup_sigcontext() so it can
be used for stateful RISC-V ISA extensions beyond the vector
extension
- Add the SBI extension ID and some initial data structure
definitions for the RISC-V standard SBI debug trigger extension
- Clean up some code slightly: change some page table functions to
avoid atomic operations oinn !SMP and to avoid unnecessary casts to
atomic_long_t; and use the existing RISCV_FULL_BARRIER macro in
place of some open-coded 'fence rw,rw' instructions"
* tag 'riscv-for-linus-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Add SBI debug trigger extension and function ids
riscv/atomic.h: use RISCV_FULL_BARRIER in _arch_atomic* function.
riscv: hwprobe: export Zilsd and Zclsd ISA extensions
riscv: add ISA extension parsing for Zilsd and Zclsd
dt-bindings: riscv: add Zilsd and Zclsd extension descriptions
riscv: mm: use xchg() on non-atomic_long_t variables, not atomic_long_xchg()
riscv: mm: ptep_get_and_clear(): avoid atomic ops when !CONFIG_SMP
riscv: mm: pmdp_huge_get_and_clear(): avoid atomic ops when !CONFIG_SMP
riscv: signal: abstract header saving for setup_sigcontext
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Madhavan Srinivasan:
- Fix for kexec warning due to SMT disable or partial SMT enabled
- Handle font bitmap pointer with reloc_offset to fix boot crash
- Fix to enable cpuidle state for Power11
- Couple of misc fixes
Thanks to Aboorva Devarajan, Aditya Bodkhe, Cedar Maxwell, Christian
Zigotzky, Christophe Leroy, Christophe Leroy (CS GROUP), Finn Thain,
Gopi Krishna Menon, Guenter Roeck, Jan Stancek, Joe Lawrence, Josh
Poimboeuf, Justin M. Forbes, Madadi Vineeth Reddy, Naveen N Rao (AMD),
Nysal Jan K.A., Sachin P Bappalige, Samir M, Sourabh Jain, Srikar
Dronamraju, and Stan Johnson
* tag 'powerpc-6.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32: Restore disabling of interrupts at interrupt/syscall exit
powerpc/powernv: Enable cpuidle state detection for POWER11
powerpc: Add reloc_offset() to font bitmap pointer used for bootx_printf()
powerpc/tools: drop `-o pipefail` in gcc check scripts
selftests/powerpc/pmu/: Add check_extended_reg_test to .gitignore
powerpc/kexec: Enable SMT before waking offline CPUs
|
|
Add header dependencies to kublk build rule so that changes to
kublk.h, ublk_dep.h, or utils.h trigger a rebuild.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add test_generic_15.sh to verify that async partition scan prevents
IO hang when reading partition tables.
The test creates ublk devices with fault_inject target and very large
delay (60s) to simulate blocked partition table reads, then kills the
daemon to verify proper state transitions without hanging:
1. Without recovery support:
- Create device with fault_inject and 60s delay
- Kill daemon while partition scan may be blocked
- Verify device transitions to DEAD state
2. With recovery support (-r 1):
- Create device with fault_inject, 60s delay, and recovery
- Kill daemon while partition scan may be blocked
- Verify device transitions to QUIESCED state
Before the async partition scan fix, killing the daemon during
partition scan would cause deadlock as partition scan held ub->mutex
while waiting for IO. With the async fix, partition scan happens in
a work function and flush_work() ensures proper synchronization.
Add _add_ublk_dev_no_settle() helper function to skip udevadm settle,
which would otherwise hang waiting for partition scan events to
complete when partition table read is delayed.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Implement async partition scan to avoid IO hang when reading partition
tables. Similar to nvme_partition_scan_work(), partition scanning is
deferred to a work queue to prevent deadlocks.
When partition scan happens synchronously during add_disk(), IO errors
can cause the partition scan to wait while holding ub->mutex, which
can deadlock with other operations that need the mutex.
Changes:
- Add partition_scan_work to ublk_device structure
- Implement ublk_partition_scan_work() to perform async scan
- Always suppress sync partition scan during add_disk()
- Schedule async work after add_disk() for trusted daemons
- Add flush_work() in ublk_stop_dev() before grabbing ub->mutex
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Reported-by: Yoav Cohen <yoav@nvidia.com>
Closes: https://lore.kernel.org/linux-block/DM4PR12MB63280C5637917C071C2F0D65A9A8A@DM4PR12MB6328.namprd12.prod.outlook.com/
Fixes: 71f28f3136af ("ublk_drv: add io_uring based userspace block driver")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit a69040ed57f5 ("sched_ext: Simplify breather mechanism with
scx_aborting flag") removed scx_in_softlockup and scx_breather_depth,
replacing them with scx_aborting.
Update the script accordingly.
Fixes: a69040ed57f5 ("sched_ext: Simplify breather mechanism with scx_aborting flag")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Commit 48e126777386 ("sched_ext: Introduce scx_sched") introduced
scx_root and removed scx_ops, causing scx_show_state.py to fail when
searching for the 'scx_ops' object. [1]
Fix by using 'scx_root' instead, with NULL pointer handling.
[1]
# drgn -s vmlinux ./tools/sched_ext/scx_show_state.py
Traceback (most recent call last):
File "/root/.venv/bin/drgn", line 8, in <module>
sys.exit(_main())
~~~~~^^
File "/root/.venv/lib64/python3.14/site-packages/drgn/cli.py", line 625, in _main
runpy.run_path(
~~~~~~~~~~~~~~^
script_path, init_globals={"prog": prog}, run_name="__main__"
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
)
^
File "<frozen runpy>", line 287, in run_path
File "<frozen runpy>", line 98, in _run_module_code
File "<frozen runpy>", line 88, in _run_code
File "./tools/sched_ext/scx_show_state.py", line 30, in <module>
ops = prog['scx_ops']
~~~~^^^^^^^^^^^
_drgn.ObjectNotFoundError: could not find 'scx_ops'
Fixes: 48e126777386 ("sched_ext: Introduce scx_sched")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Route bfqg_stats_add_aux() time accumulation into the destination
stats object instead of the source, aligning with other stat fields.
Reviewed-by: Yu Kuai <yukuai@fnnas.com>
Signed-off-by: shechenglong <shechenglong@xfusion.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A previous commit added SO_INQ support for AF_UNIX (SOCK_STREAM), but it
posts a SCM_INQ cmsg even if just msg->msg_get_inq is set. This is
incorrect, as ->msg_get_inq is just the caller asking for the remainder
to be passed back in msg->msg_inq, it has nothing to do with cmsg. The
original commit states that this is done to make sockets
io_uring-friendly", but it's actually incorrect as io_uring doesn't use
cmsg headers internally at all, and it's actively wrong as this means
that cmsg's are always posted if someone does recvmsg via io_uring.
Fix that up by only posting a cmsg if u->recvmsg_inq is set.
Additionally, mirror how TCP handles inquiry handling in that it should
only be done for a successful return. This makes the logic for the two
identical.
Cc: stable@vger.kernel.org
Fixes: df30285b3670 ("af_unix: Introduce SO_INQ.")
Reported-by: Julian Orth <ju.orth@gmail.com>
Link: https://github.com/axboe/liburing/issues/1509
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/07adc0c2-2c3b-4d08-8af1-1c466a40b6a8@kernel.dk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wbg/counter into char-misc-linus
William writes:
Counter fixes for 6.19
A fix for interrupt-cnt dropping the IRQF_NO_THREAD configuration to
allow the IRQ handler to correctly acquire a spinlock_t lock. A fix for
104-quad-8 correcting quad8_irq_handler() to return irqreturn_t enum
values rather than negative errno codes on error.
* tag 'counter-fixes-for-6.19' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wbg/counter:
counter: 104-quad-8: Fix incorrect return value in IRQ handler
counter: interrupt-cnt: Drop IRQF_NO_THREAD flag
|
|
Commit a10ad1b10402 ("PM: suspend: Make pm_test delay interruptible by
wakeup events") replaced mdelay() in suspend_test() with msleep() which
does not work at the TEST_CORE test level that calls suspend_test()
while running on one CPU with interrupts off.
Address this by making suspend_test() check if the test level is
suitable for using msleep() and use mdelay() otherwise.
Fixes: a10ad1b10402 ("PM: suspend: Make pm_test delay interruptible by wakeup events")
Reported-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Closes: https://lore.kernel.org/linux-pm/aUsAk0k1N9hw8IkY@venus/
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patch.msgid.link/6251576.lOV4Wx5bFT@rafael.j.wysocki
|
|
Shows registration of a SoC device upon receipt of a probe.
Signed-off-by: Matthew Maurer <mmaurer@google.com>
Link: https://patch.msgid.link/20251226-soc-bindings-v4-3-2c2fac08f820@google.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Allow SoC drivers in Rust to present metadata about their devices to
userspace through /sys/devices/socX and other drivers to identify their
properties through `soc_device_match`.
Signed-off-by: Matthew Maurer <mmaurer@google.com>
Link: https://patch.msgid.link/20251226-soc-bindings-v4-1-2c2fac08f820@google.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Add the OTP controller node.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20251222-gs101-chipid-v4-5-aa8e20ce7bb3@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
GS101 is different (but also e850 and autov9 I assume) from the SoCs
that are currently handled by the exynos-chipid driver because the
chip ID info is part of the OTP registers. GS101 OTP has a clock, an
interrupt line, a register space (that contains product and chip ID,
TMU data, ASV, etc) and a 32Kbit memory space that can be
read/program/locked with specific commands. On GS101 the "ChipID block"
is just an abstraction, it's not a physical device. When the power-on
sequence progresses, the OTP chipid values are loaded to the OTP
registers.
Add the GS101 chip ID support. The support is intentionally added in the
exynos-chipid driver, and not in a dedicated Exynos OTP driver, because
we estimate that there will not be any OTP consumers in the kernel other
than the chip ID/SoC interface. The downstream GS101 drivers confirm
this supposition.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20251222-gs101-chipid-v4-4-aa8e20ce7bb3@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The SoC information is exposed to userspace using the standard soc
interface. Downgrade to dev_dbg to stop polluting the console log.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20251222-gs101-chipid-v4-3-aa8e20ce7bb3@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
s/product_id_to_soc_id/exynos_product_id_to_name.
Prepend exynos_ to avoid name space pollution. The method translates the
product id to a name, rename the method to make that clear. While
touching the code where it is called, add a blank line for readability
purposes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20251222-gs101-chipid-v4-2-aa8e20ce7bb3@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add binding for the OTP controller found on Google GS101.
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20251222-gs101-chipid-v4-1-aa8e20ce7bb3@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In w1_attach_slave_device(), if __w1_attach_slave_device() fails,
put_device() -> w1_slave_release() is called to do the cleanup job.
In w1_slave_release(), sl->family->refcnt and sl->master->slave_count
have already been decremented. There is no need to decrement twice
in w1_attach_slave_device().
Fixes: 2c927c0c73fd ("w1: Fix slave count on 1-Wire bus (resend)")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Link: https://patch.msgid.link/20251218111414.564403-1-lihaoxiang@isrc.iscas.ac.cn
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
When mana_serv_reset() encounters -ETIMEDOUT or -EPROTO from
mana_gd_resume(), it performs a PCI rescan via mana_serv_rescan().
mana_serv_rescan() calls pci_stop_and_remove_bus_device(), which can
invoke the driver's remove path and free the gdma_context associated
with the device. After returning, mana_serv_reset() currently jumps to
the out label and attempts to clear gc->in_service, dereferencing a
freed gdma_context.
The issue was observed with the following call logs:
[ 698.942636] BUG: unable to handle page fault for address: ff6c2b638088508d
[ 698.943121] #PF: supervisor write access in kernel mode
[ 698.943423] #PF: error_code(0x0002) - not-present page
[S[ 698.943793] Pat Dec 6 07:GD5 100000067 P4D 1002f7067 PUD 1002f8067 PMD 101bef067 PTE 0
0:56 2025] hv_[n e 698.944283] Oops: Oops: 0002 [#1] SMP NOPTI
tvsc f8615163-00[ 698.944611] CPU: 28 UID: 0 PID: 249 Comm: kworker/28:1
...
[Sat Dec 6 07:50:56 2025] R10: [ 699.121594] mana 7870:00:00.0 enP30832s1: Configured vPort 0 PD 18 DB 16
000000000000001b R11: 0000000000000000 R12: ff44cf3f40270000
[Sat Dec 6 07:50:56 2025] R13: 0000000000000001 R14: ff44cf3f402700c8 R15: ff44cf3f4021b405
[Sat Dec 6 07:50:56 2025] FS: 0000000000000000(0000) GS:ff44cf7e9fcf9000(0000) knlGS:0000000000000000
[Sat Dec 6 07:50:56 2025] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[Sat Dec 6 07:50:56 2025] CR2: ff6c2b638088508d CR3: 000000011fe43001 CR4: 0000000000b73ef0
[Sat Dec 6 07:50:56 2025] Call Trace:
[Sat Dec 6 07:50:56 2025] <TASK>
[Sat Dec 6 07:50:56 2025] mana_serv_func+0x24/0x50 [mana]
[Sat Dec 6 07:50:56 2025] process_one_work+0x190/0x350
[Sat Dec 6 07:50:56 2025] worker_thread+0x2b7/0x3d0
[Sat Dec 6 07:50:56 2025] kthread+0xf3/0x200
[Sat Dec 6 07:50:56 2025] ? __pfx_worker_thread+0x10/0x10
[Sat Dec 6 07:50:56 2025] ? __pfx_kthread+0x10/0x10
[Sat Dec 6 07:50:56 2025] ret_from_fork+0x21a/0x250
[Sat Dec 6 07:50:56 2025] ? __pfx_kthread+0x10/0x10
[Sat Dec 6 07:50:56 2025] ret_from_fork_asm+0x1a/0x30
[Sat Dec 6 07:50:56 2025] </TASK>
Fix this by returning immediately after mana_serv_rescan() to avoid
accessing GC state that may no longer be valid.
Fixes: 9bf66036d686 ("net: mana: Handle hardware recovery events when probing the device")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Link: https://patch.msgid.link/20251218131054.GA3173@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
