When run the test in netns, it's not easy to get the tc stats via tc_rule_handle_stats_get(). With the new netns parameter, we can get stats from specific netns like num=$(tc_rule_handle_stats_get "dev eth0 ingress" 101 ".packets" "-n ns") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT46 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 03a0b567a03d ("selftests: seg6: add selftest for SRv6 End.DT46 Behavior")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases for bridge neighbor suppression, testing both per-port
and per-{Port, VLAN} neighbor suppression with both ARP and NS packets.
Example truncated output:
# ./test_bridge_neigh_suppress.sh
[...]
Tests passed: 148
Tests failed: 0
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC Merge layer (IEEE 802.3-2018 clause 99) does all the heavy lifting for Frame Preemption (IEEE 802.1Q-2018 clause 6.7.2), a TSN feature for minimizing latency. Preemptible traffic is different on the wire from normal traffic in incompatible ways. If we send a preemptible packet and the link partner doesn't support preemption, it will drop it as an error frame and we will never know. The MAC Merge layer has a control plane of its own, which can be manipulated (using ethtool) in order to negotiate this capability with the link partner (through LLDP). Actually the TLV format for LLDP solves this problem only partly, because both partners only advertise: - if they support preemption (RX and TX) - if they have enabled preemption (TX) so we cannot tell the link partner what to do - we cannot force it to enable reception of our preemptible packets. That is fully solved by the verification feature, where the local device generates some small probe frames which look like preemptible frames with no useful content, and the link partner is obliged to respond to them if it supports the standard. If the verification times out, we know that preemption isn't active in our TX direction on the link. Having clarified the definition, this selftest exercises the manual (ethtool) configuration path of 2 link partners (with and without verification), and the LLDP code path, using the openlldp project. The test also verifies the TX activity of the MAC Merge layer by sending traffic through a traffic class configured as preemptible (using mqprio). There isn't a good way to make this really portable (user space cannot find out how many traffic classes there are for a device), but I chose num_tc 4 here, that should work reasonably well. I also know that some devices (stmmac) only permit TXQ0 to be preemptible, so this is why PREEMPTIBLE_PRIO was strategically chosen as 0. Even if other hardware is more configurable, this test should cover the baseline. This is not really a "forwarding" selftest, but I put it near the other "ethtool" selftests. $ ./ethtool_mm.sh eno0 swp0 TEST: Manual configuration with verification: eno0 to swp0 [ OK ] TEST: Manual configuration with verification: swp0 to eno0 [ OK ] TEST: Manual configuration without verification: eno0 to swp0 [ OK ] TEST: Manual configuration without verification: swp0 to eno0 [ OK ] TEST: Manual configuration with failed verification: eno0 to swp0 [ OK ] TEST: Manual configuration with failed verification: swp0 to eno0 [ OK ] TEST: LLDP [ OK ] Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Counters for the MAC Merge layer and preemptible MAC have standardized so far on using structured ethtool stats as opposed to the driver specific names and meanings. Benefit from that rare opportunity and introduce a helper to lib.sh for querying standardized counters, in the hope that these will take off for other uses as well. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlxsw selftests often invoke a bail_on_lldpad() helper to make sure LLDPAD is not running, to prevent conflicts between the QoS configuration applied through TC or DCB command line tool, and the DCB configuration that LLDPAD might apply. This helper might be useful to others. Move the function to lib.sh, and parameterize to make reusable in other contexts. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver-specific wrappers of these selftests invoke bail_on_lldpad to make sure that LLDPAD doesn't trample the configuration. The function bail_on_lldpad is going to move to lib.sh in the next patch. With that, it won't be visible for the wrappers before sourcing the framework script. And after sourcing it, it is too late: the selftest will have run by then. One option might be to source NUM_NETIFS=0 lib.sh from the wrapper, but even if that worked (it might, it might not), that seems cumbersome. lib.sh is doing fair amount of stuff, and even if it works today, it does not look particularly solid as a solution. Instead, introduce a hook, sch_tbf_pre_hook(), that when available, gets invoked. Move the bail to the hook. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the code had an issue according to ShellCheck. That's mainly due to the fact it incorrectly believes most of the code was unreachable because it's invoked by variable name, see how the "tests" array is used. Once SC2317 has been ignored, three small warnings were still visible: - SC2155: Declare and assign separately to avoid masking return values. - SC2046: Quote this to prevent word splitting: can be ignored because "ip netns pids" can display more than one pid. - SC2166: Prefer [ p ] || [ q ] as [ p -o q ] is not well defined. This probably didn't fix any actual issues but it might help spotting new interesting warnings reported by ShellCheck as just before, ShellCheck was reporting issues for most lines making it a bit useless. Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_connect tool was printing some duplicated entries when showing how
to use it: -j -l -r
While at it, I also:
- moved the very few entries that were not sorted,
- added -R that was missing since
commit 8a4b910d005d ("mptcp: selftests: add rcvbuf set option"),
- removed the -u parameter that has been removed in
commit f730b65c9d85 ("selftests: mptcp: try to set mptcp ulp mode in different sk states").
No need to backport this, it is just an internal tool used by our
selftests. The help menu is mainly useful for MPTCP kernel devs.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upcall socket interface can be exercised now to make sure that future feature adjustments to the field can maintain backwards compatibility. Signed-off-by: Aaron Conole <aconole@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>