The mesh path timer needs to be canceled when
leaving the mesh as otherwise it could fire
after the interface has been removed already.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.

This affects both mesh and managed modes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ieee80211_request_sched_scan_stop() cleared
local->sched_scan_sdata. However, sched_scan_sdata
should be cleared only after the driver calls
ieee80211_sched_scan_stopped() (like with normal hw scan).

Clearing sched_scan_sdata too early caused
ieee80211_sched_scan_stopped_work to exit prematurely
without properly cleaning all the sched scan resources
and without calling cfg80211_sched_scan_stopped (so
userspace wasn't notified about sched scan completion).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull LED subsystem update from Bryan Wu.

* 'for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (50 commits)
  leds-lp8788: forgotten unlock at lp8788_led_work
  LEDS: propagate error codes in blinkm_detect()
  LEDS: memory leak in blinkm_led_common_set()
  leds: add new lp8788 led driver
  LEDS: add BlinkM RGB LED driver, documentation and update MAINTAINERS
  leds: max8997: Simplify max8997_led_set_mode implementation
  leds/leds-s3c24xx: use devm_gpio_request
  leds: convert Network Space v2 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert DAC124S085 LED driver to devm_kzalloc()
  leds: convert LM3530 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert TCA6507 LED driver to devm_kzalloc()
  leds: convert Freescale MC13783 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert ADP5520 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert PCA955x LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert Sun Fire LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert PCA9532 LED driver to devm_kzalloc()
  leds: convert LT3593 LED driver to devm_kzalloc()
  leds: convert Renesas TPU LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert LP5523 LED driver to devm_kzalloc() and cleanup error exit path
  leds: convert PCA9633 LED driver to devm_kzalloc()
  ...

We need to use RCU to assign scan_sdata.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rename leds external interface led_brightness_set() to led_set_brightness().
This is the second phase of the change to reduce confusion between the
leds internal and external interfaces that set brightness. With this change,
now the external interface is led_set_brightness(). The first phase renamed
the internal interface led_set_brightness() to __led_set_brightness().
There are no changes to the interface implementations.

Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>