linux.git/net/mac80211/tx.c, branch v3.5

mac80211: Fix Unreachable Mesh Station Problem when joining to another MBSS

2012-06-04T19:23:23+00:00

Mesh station that joins an MBSS is reachable using mesh portal with 6
address frame by mesh stations from another MBSS if these two different
MBSSes are bridged. However, if the mesh station later moves into the
same MBSS of those mesh stations, it is unreachable by mesh stations
in the MBSS due to the mpp_paths table is not deleted. A quick fix
is to perform mesh_path_lookup, if it is available for the target
destination, mpp_path_lookup is not performed. When the mesh station
moves back to its original MBSS, the mesh_paths will be deleted once
expired. So, it will be reachable using mpp_path_lookup again.

Signed-off-by: Chun-Yeow Yeoh 
Signed-off-by: John W. Linville

mac80211: fix flag check for QoS NOACK frames

2012-05-29T17:45:23+00:00

Signed-off-by: Claudio Pisa 
Signed-off-by: John W. Linville

net: Convert net_ratelimit uses to net__ratelimited

2012-05-15T17:45:03+00:00

Standardize the net core ratelimited logging functions.

Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.

Signed-off-by: Joe Perches 
Signed-off-by: David S. Miller

mac80211: Convert compare_ether_addr to ether_addr_equal

2012-05-10T00:49:18+00:00

Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)

Signed-off-by: Joe Perches 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2012-05-08T03:35:40+00:00

Conflicts:
	drivers/net/ethernet/intel/e1000e/param.c
	drivers/net/wireless/iwlwifi/iwl-agn-rx.c
	drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
	drivers/net/wireless/iwlwifi/iwl-trans.h

Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell.  In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.

In e1000e a conflict arose in the validation code for settings of
adapter->itr.  'net-next' had more sophisticated logic so that
logic was used.

Signed-off-by: David S. Miller

mac80211: fix AP mode EAP tx for VLAN stations

2012-04-30T18:40:05+00:00

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.

Signed-off-by: Felix Fietkau 
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville

mac80211: rename AP variable num_sta_authorized to num_mcast_sta

2012-04-24T18:54:28+00:00

It is only used to test for BSS multicast receivers.

Signed-off-by: Felix Fietkau 
Reviewed-by: Johannes Berg 
Signed-off-by: John W. Linville

mac80211: remove hw.conf.channel usage where possible

2012-04-13T18:32:50+00:00

Removes hw.conf.channel usage from the following functions:
 * ieee80211_mandatory_rates
 * ieee80211_sta_get_rates
 * ieee80211_frame_duration
 * ieee80211_rts_duration
 * ieee80211_ctstoself_duration

This is in preparation for multi-channel operation.

Signed-off-by: Michal Kazior 
Signed-off-by: John W. Linville

mac80211: add improved HW queue control

2012-04-11T20:23:50+00:00

mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.

To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.

Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.

Signed-off-by: Johannes Berg 
Signed-off-by: John W. Linville

mac80211: add explicit monitor interface if needed

2012-04-11T20:23:49+00:00

The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.

So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.

Signed-off-by: Johannes Berg 
Signed-off-by: John W. Linville