linux.git/net/irda/ircomm, branch v3.9

net/irda: Raise dtr in non-blocking open

2013-03-06T07:47:05+00:00

DTR/RTS need to be raised, regardless of the open() mode, but not
if the port has already shutdown.

Signed-off-by: Peter Hurley 
Signed-off-by: David S. Miller

net/irda: Use barrier to set task state

2013-03-06T07:47:04+00:00

Without a memory and compiler barrier, the task state change
can migrate relative to the condition testing in a blocking loop.
However, the task state change must be visible across all cpus
prior to testing those conditions. Failing to do this can result
in the familiar 'lost wakeup' and this task will hang until killed.

Signed-off-by: Peter Hurley 
Signed-off-by: David S. Miller

net/irda: Hold port lock while bumping blocked_open

2013-03-06T07:47:04+00:00

Although tty_lock() already protects concurrent update to
blocked_open, that fails to meet the separation-of-concerns between
tty_port and tty.

Signed-off-by: Peter Hurley 
Signed-off-by: David S. Miller

net/irda: Fix port open counts

2013-03-06T07:47:04+00:00

Saving the port count bump is unsafe. If the tty is hung up while
this open was blocking, the port count is zeroed.

Explicitly check if the tty was hung up while blocking, and correct
the port count if not.

Signed-off-by: Peter Hurley 
Signed-off-by: David S. Miller

tty: Added a CONFIG_TTY option to allow removal of TTY

2013-01-19T00:15:27+00:00

The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48

Signed-off-by: Joe Millenbach 
Reviewed-by: Jamey Sharp 
Reviewed-by: Josh Triplett 
Signed-off-by: Greg Kroah-Hartman

TTY: switch tty_flip_buffer_push

2013-01-16T06:30:15+00:00

Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.

Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.

IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.

Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.

Signed-off-by: Jiri Slaby 
Signed-off-by: Greg Kroah-Hartman

TTY: move low_latency to tty_port

2013-01-16T06:23:16+00:00

One point is to have less places where we actually need tty pointer.
The other is that low_latency is bound to buffer processing and
buffers are now in tty_port. So it makes sense to move low_latency to
tty_port too.

Signed-off-by: Jiri Slaby 
Signed-off-by: Greg Kroah-Hartman

TTY: switch tty_insert_flip_string

2013-01-16T06:22:35+00:00

Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.

tty_insert_flip_string this time.

Signed-off-by: Jiri Slaby 
Signed-off-by: Greg Kroah-Hartman

TTY: call tty_port_destroy in the rest of drivers

2012-11-16T01:20:58+00:00

After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.

To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.

Signed-off-by: Jiri Slaby 
Signed-off-by: Greg Kroah-Hartman

net, TTY: initialize tty->driver_data before usage

2012-10-05T16:26:01+00:00

Commit 9c650ffc ("TTY: ircomm_tty, add tty install") split _open() to
_install() and _open(). It also moved the initialization of driver_data
out of open(), but never added it to install() - causing a NULL ptr
deref whenever the driver was used.

Signed-off-by: Sasha Levin 
Acked-by: Jiri Slaby 
Signed-off-by: Greg Kroah-Hartman