linux.git/net/ipv6, branch v4.8-rc6

udp: get rid of SLAB_DESTROY_BY_RCU allocations

2016-08-24T00:46:17+00:00

After commit ca065d0cf80f ("udp: no longer use SLAB_DESTROY_BY_RCU")
we do not need this special allocation mode anymore, even if it is
harmless.

Signed-off-by: Eric Dumazet 
Signed-off-by: David S. Miller

tcp: properly scale window in tcp_v[46]_reqsk_send_ack()

2016-08-23T23:55:49+00:00

When sending an ack in SYN_RECV state, we must scale the offered
window if wscale option was negotiated and accepted.

Tested:
 Following packetdrill test demonstrates the issue :

0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0

+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0

// Establish a connection.
+0 < S 0:0(0) win 20000 
+0 > S. 0:0(0) ack 1 win 28960 

+0 < . 1:11(10) ack 1 win 156 
// check that window is properly scaled !
+0 > . 1:1(0) ack 1 win 226 

Signed-off-by: Eric Dumazet 
Cc: Yuchung Cheng 
Cc: Neal Cardwell 
Acked-by: Yuchung Cheng 
Acked-by: Neal Cardwell 
Signed-off-by: David S. Miller

net: ipv6: Remove addresses for failures with strict DAD

2016-08-22T23:59:37+00:00

If DAD fails with accept_dad set to 2, global addresses and host routes
are incorrectly left in place. Even though disable_ipv6 is set,
contrary to documentation, the addresses are not dynamically deleted
from the interface. It is only on a subsequent link down/up that these
are removed. The fix is not only to set the disable_ipv6 flag, but
also to call addrconf_ifdown(), which is the action to carry out when
disabling IPv6. This results in the addresses and routes being deleted
immediately. The DAD failure for the LL addr is determined as before
via netlink, or by the absence of the LL addr (which also previously
would have had to be checked for in case of an intervening link down
and up). As the call to addrconf_ifdown() requires an rtnl lock, the
logic to disable IPv6 when DAD fails is moved to addrconf_dad_work().

Previous behavior:

root@vm1:/# sysctl net.ipv6.conf.eth3.accept_dad=2
net.ipv6.conf.eth3.accept_dad = 2
root@vm1:/# ip -6 addr add 2000::10/64 dev eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
5: eth3:  mtu 1500 qlen 1000
    inet6 2000::10/64 scope global
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe43:dd5a/64 scope link tentative dadfailed
       valid_lft forever preferred_lft forever
root@vm1:/# ip -6 route show dev eth3
2000::/64  proto kernel  metric 256
fe80::/64  proto kernel  metric 256
root@vm1:/# ip link set down eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
root@vm1:/# ip -6 route show dev eth3
root@vm1:/#

New behavior:

root@vm1:/# sysctl net.ipv6.conf.eth3.accept_dad=2
net.ipv6.conf.eth3.accept_dad = 2
root@vm1:/# ip -6 addr add 2000::10/64 dev eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
root@vm1:/# ip -6 route show dev eth3
root@vm1:/#

Signed-off-by: Mike Manning 
Signed-off-by: David S. Miller

gre: set inner_protocol on xmit

2016-08-15T20:37:12+00:00

Ensure that the inner_protocol is set on transmit so that GSO segmentation,
which relies on that field, works correctly.

This is achieved by setting the inner_protocol in gre_build_header rather
than each caller of that function. It ensures that the inner_protocol is
set when gre_fb_xmit() is used to transmit GRE which was not previously the
case.

I have observed this is not the case when OvS transmits GRE using
lwtunnel metadata (which it always does).

Fixes: 38720352412a ("gre: Use inner_proto to obtain inner header protocol")
Cc: Pravin Shelar 
Acked-by: Alexander Duyck 
Signed-off-by: Simon Horman 
Acked-by: Pravin B Shelar 
Signed-off-by: David S. Miller

net: ipv6: Fix ping to link-local addresses.

2016-08-15T19:19:09+00:00

ping_v6_sendmsg does not set flowi6_oif in response to
sin6_scope_id or sk_bound_dev_if, so it is not possible to use
these APIs to ping an IPv6 address on a different interface.
Instead, it sets flowi6_iif, which is incorrect but harmless.

Stop setting flowi6_iif, and support various ways of setting oif
in the same priority order used by udpv6_sendmsg.

Tested: https://android-review.googlesource.com/#/c/254470/
Signed-off-by: Lorenzo Colitti 
Signed-off-by: David S. Miller

net: ipv6: Do not keep IPv6 addresses when IPv6 is disabled

2016-08-13T22:14:00+00:00

If IPv6 is disabled when the option is set to keep IPv6
addresses on link down, userspace is unaware of this as
there is no such indication via netlink. The solution is to
remove the IPv6 addresses in this case, which results in
netlink messages indicating removal of addresses in the
usual manner. This fix also makes the behavior consistent
with the case of having IPv6 disabled first, which stops
IPv6 addresses from being added.

Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning 
Acked-by: David Ahern 
Signed-off-by: David S. Miller

calipso: fix resource leak on calipso_genopt failure

2016-08-13T21:56:17+00:00

Currently, if calipso_genopt fails then the error exit path
does not free the ipv6_opt_hdr new causing a memory leak. Fix
this by kfree'ing new on the error exit path.

Signed-off-by: Colin Ian King 
Signed-off-by: David S. Miller

net: ipv6: use list_move instead of list_del/list_add

2016-07-31T03:41:59+00:00

Using list_move() instead of list_del() + list_add().

Signed-off-by: Wei Yongjun 
Signed-off-by: David S. Miller

Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

2016-07-30T00:38:46+00:00

Pull security subsystem updates from James Morris:
 "Highlights:

   - TPM core and driver updates/fixes
   - IPv6 security labeling (CALIPSO)
   - Lots of Apparmor fixes
   - Seccomp: remove 2-phase API, close hole where ptrace can change
     syscall #"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
  apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
  tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
  tpm: Factor out common startup code
  tpm: use devm_add_action_or_reset
  tpm2_i2c_nuvoton: add irq validity check
  tpm: read burstcount from TPM_STS in one 32-bit transaction
  tpm: fix byte-order for the value read by tpm2_get_tpm_pt
  tpm_tis_core: convert max timeouts from msec to jiffies
  apparmor: fix arg_size computation for when setprocattr is null terminated
  apparmor: fix oops, validate buffer size in apparmor_setprocattr()
  apparmor: do not expose kernel stack
  apparmor: fix module parameters can be changed after policy is locked
  apparmor: fix oops in profile_unpack() when policy_db is not present
  apparmor: don't check for vmalloc_addr if kvzalloc() failed
  apparmor: add missing id bounds check on dfa verification
  apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
  apparmor: use list_next_entry instead of list_entry_next
  apparmor: fix refcount race when finding a child profile
  apparmor: fix ref count leak when profile sha1 hash is read
  apparmor: check that xindex is in trans_table bounds
  ...

net: ipmr/ip6mr: update lastuse on entry change

2016-07-26T22:18:31+00:00

Currently lastuse is updated on entry creation and cache hit, but it should
also be updated on entry change. Since both on add and update the ttl array
is updated we can simply update the lastuse in ipmr_update_thresholds.

Signed-off-by: Nikolay Aleksandrov 
CC: Roopa Prabhu 
CC: Donald Sharp 
CC: David S. Miller 
Signed-off-by: David S. Miller