linux.git/net/ipv4/ip_gre.c, branch v4.15

ip_gre: remove the incorrect mtu limit for ipgre tap

2017-12-19T18:45:32+00:00

ipgre tap driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.

It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.

Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.

Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Reported-by: Jianlin Shi 
Signed-off-by: Xin Long 
Signed-off-by: David S. Miller

ip_gre: fix wrong return value of erspan_rcv

2017-12-15T19:10:39+00:00

If pskb_may_pull return failed, return PACKET_REJECT instead of -ENOMEM.

Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Cc: William Tu 
Signed-off-by: Haishuang Yan 
Acked-by: William Tu 
Signed-off-by: David S. Miller

ip_gre: add the support for i/o_flags update via ioctl

2017-11-10T05:39:53+00:00

As patch 'ip_gre: add the support for i/o_flags update via netlink'
did for netlink, we also need to do the same job for these update
via ioctl.

This patch is to update i/o_flags and call ipgre_link_update to
recalculate these gre properties after ip_tunnel_ioctl does the
common update.

Signed-off-by: Xin Long 
Acked-by: William Tu 
Signed-off-by: David S. Miller

ip_gre: add the support for i/o_flags update via netlink

2017-11-10T05:39:53+00:00

Now ip_gre is using ip_tunnel_changelink to update it's properties, but
ip_tunnel_changelink in ip_tunnel doesn't update i/o_flags as a common
function.

o_flags updates would cause that tunnel->tun_hlen / hlen and dev->mtu /
needed_headroom need to be recalculated, and dev->(hw_)features need to
be updated as well.

Therefore, we can't just add the update into ip_tunnel_update called
in ip_tunnel_changelink, and it's also better not to touch ip_tunnel
codes.

This patch updates i/o_flags and calls ipgre_link_update to recalculate
these gre properties after ip_tunnel_changelink does the common update.

Note that since ipgre_link_update doesn't know the lower dev, it will
update gre->hlen, dev->mtu and dev->needed_headroom with the value of
'new tun_hlen - old tun_hlen'. In this way, we can avoid many redundant
codes, unlike ip6_gre.

Reported-by: Jianlin Shi 
Signed-off-by: Xin Long 
Acked-by: William Tu 
Signed-off-by: David S. Miller

ip_gre: check packet length and mtu correctly in erspan tx

2017-10-07T22:17:21+00:00

Similarly to early patch for erspan_xmit(), the ARPHDR_ETHER device
is the length of the whole ether packet.  So skb->len should subtract
the dev->hard_header_len.

Fixes: 1a66a836da63 ("gre: add collect_md mode to ERSPAN tunnel")
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: William Tu 
Cc: Xin Long 
Cc: David Laight 
Reviewed-by: Xin Long 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2017-10-06T01:19:22+00:00

Just simple overlapping changes.

Signed-off-by: David S. Miller

ip_gre: erspan device should keep dst

2017-10-02T05:30:32+00:00

The patch 'ip_gre: ipgre_tap device should keep dst' fixed
the issue ipgre_tap dev mtu couldn't be updated in tx path.

The same fix is needed for erspan as well.

Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long 
Signed-off-by: David S. Miller

ip_gre: set tunnel hlen properly in erspan_tunnel_init

2017-10-02T05:30:32+00:00

According to __gre_tunnel_init, tunnel->hlen should be set as the
headers' length between inner packet and outer iphdr.

It would be used especially to calculate a proper mtu when updating
mtu in tnl_update_pmtu. Now without setting it, a bigger mtu value
than expected would be updated, which hurts performance a lot.

This patch is to fix it by setting tunnel->hlen with:
   tunnel->tun_hlen + tunnel->encap_hlen + sizeof(struct erspanhdr)

Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long 
Signed-off-by: David S. Miller

ip_gre: check packet length and mtu correctly in erspan_xmit

2017-10-02T05:30:32+00:00

As a ARPHRD_ETHER device, skb->len in erspan_xmit is the length
of the whole ether packet. So before checking if a packet size
exceeds the mtu, skb->len should subtract dev->hard_header_len.

Otherwise, all packets with max size according to mtu would be
trimmed to be truncated packet.

Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long 
Signed-off-by: David S. Miller

ip_gre: get key from session_id correctly in erspan_rcv

2017-10-02T05:30:32+00:00

erspan only uses the first 10 bits of session_id as the key to look
up the tunnel. But in erspan_rcv, it missed 'session_id & ID_MASK'
when getting the key from session_id.

If any other flag is also set in session_id in a packet, it would
fail to find the tunnel due to incorrect key in erspan_rcv.

This patch is to add 'session_id & ID_MASK' there and also remove
the unnecessary variable session_id.

Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long 
Signed-off-by: David S. Miller