Since commit d253eee20195b25e298bf162a6e72f14bf4803e5 the single CAN
identifier filter lists handle only non-RTR CAN frames.

So we need to omit the check of these filter lists when receiving RTR
CAN frames.

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a wrong safety check in af_can.c it was not possible to filter
for SFF frames with a specific CAN identifier without getting the
same selected CAN identifier from a received EFF frame also.

This fix has a minimum (but user visible) impact on the CAN filter
API and therefore the CAN version is set to a new date.

Indeed the 'old' API is still working as-is. But when now setting
CAN_(EFF|RTR)_FLAG in can_filter.can_mask you might get less traffic
than before - but still the stuff that you expected to get for your
defined filter ...

Thanks to Kurt Van Dijck for pointing at this issue and for the review.

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without CONFIG_NET_NS, namespace is always &init_net.
Compiler will be able to omit namespace comparisons with this patch.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though the CAN netlayer only deals with CAN netdevices, the 
netlayer interface to the userspace and to the device layer should 
perform some sanity checks.

This patch adds several sanity checks that mainly prevent userspace apps 
to send broken content into the system that may be misinterpreted by 
some other userspace application.

Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Acked-by: Andre Naujoks <nautsch@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  net: Added ASSERT_RTNL() to dev_open() and dev_close().
  can: Fix can_send() handling on dev_queue_xmit() failures
  netns: Fix arbitrary net_device-s corruptions on net_ns stop.
  netfilter: Kconfig: default DCCP/SCTP conntrack support to the protocol config values
  netfilter: nf_conntrack_sip: restrict RTP expect flushing on error to last request
  macvlan: Fix memleak on device removal/crash on module removal
  net/ipv4: correct RFC 1122 section reference in comment
  tcp FRTO: SACK variant is errorneously used with NewReno
  e1000e: don't return half-read eeprom on error
  ucc_geth: Don't use RX clock as TX clock.
  cxgb3: Use CAP_SYS_RAWIO for firmware
  pcnet32: delete non NAPI code from driver.
  fs_enet: Fix a memory leak in fs_enet_mdio_probe
  [netdrvr] eexpress: IPv6 fails - multicast problems
  3c59x: use netstats in net_device structure
  3c980-TX needs EXTRA_PREAMBLE
  fix warning in drivers/net/appletalk/cops.c
  e1000e: Add support for BM PHYs on ICH9
  uli526x: fix endianness issues in the setup frame
  uli526x: initialize the hardware prior to requesting interrupts
  ...

The tx packet counting and the local loopback of CAN frames should
only happen in the case that the CAN frame has been enqueued to the
netdevice tx queue successfully.

Thanks to Andre Naujoks <nautsch@gmail.com> for reporting this issue.

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The helper function hrtimer_callback_running() is used in
kernel/hrtimer.c as well as in the updated net/can/bcm.c which now
supports hrtimers. Moving the helper function to hrtimer.h removes the
duplicate definition in the C-files.

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Both copy_to_ and _from_user return the number of bytes, that failed to
reach their destination, not the 0/-EXXX values.

Based on patch from Pavel Emelyanov <xemul@openvz.org>

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

I found some places, that erroneously return the value obtained from
the copy_to_user() call: if some amount of bytes were not able to get
to the user (this is what this one returns) the proper behavior is to
return the -EFAULT error, not that number itself.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>