Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull networking updates from David Miller:
 "Highlights:

   1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.

   2) Add fib_sync_mem to control the amount of dirty memory we allow to
      queue up between synchronize RCU calls, from David Ahern.

   3) Make flow classifier more lockless, from Vlad Buslov.

   4) Add PHY downshift support to aquantia driver, from Heiner
      Kallweit.

   5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
      contention on SLAB spinlocks in heavy RPC workloads.

   6) Partial GSO offload support in XFRM, from Boris Pismenny.

   7) Add fast link down support to ethtool, from Heiner Kallweit.

   8) Use siphash for IP ID generator, from Eric Dumazet.

   9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
      entries, from David Ahern.

  10) Move skb->xmit_more into a per-cpu variable, from Florian
      Westphal.

  11) Improve eBPF verifier speed and increase maximum program size,
      from Alexei Starovoitov.

  12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
      spinlocks. From Neil Brown.

  13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.

  14) Improve link partner cap detection in generic PHY code, from
      Heiner Kallweit.

  15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
      Maguire.

  16) Remove SKB list implementation assumptions in SCTP, your's truly.

  17) Various cleanups, optimizations, and simplifications in r8169
      driver. From Heiner Kallweit.

  18) Add memory accounting on TX and RX path of SCTP, from Xin Long.

  19) Switch PHY drivers over to use dynamic featue detection, from
      Heiner Kallweit.

  20) Support flow steering without masking in dpaa2-eth, from Ioana
      Ciocoi.

  21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
      Pirko.

  22) Increase the strict parsing of current and future netlink
      attributes, also export such policies to userspace. From Johannes
      Berg.

  23) Allow DSA tag drivers to be modular, from Andrew Lunn.

  24) Remove legacy DSA probing support, also from Andrew Lunn.

  25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
      Haabendal.

  26) Add a generic tracepoint for TX queue timeouts to ease debugging,
      from Cong Wang.

  27) More indirect call optimizations, from Paolo Abeni"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
  cxgb4: Fix error path in cxgb4_init_module
  net: phy: improve pause mode reporting in phy_print_status
  dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
  net: macb: Change interrupt and napi enable order in open
  net: ll_temac: Improve error message on error IRQ
  net/sched: remove block pointer from common offload structure
  net: ethernet: support of_get_mac_address new ERR_PTR error
  net: usb: smsc: fix warning reported by kbuild test robot
  staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
  net: dsa: support of_get_mac_address new ERR_PTR error
  net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
  vrf: sit mtu should not be updated when vrf netdev is the link
  net: dsa: Fix error cleanup path in dsa_init_module
  l2tp: Fix possible NULL pointer dereference
  taprio: add null check on sched_nest to avoid potential null pointer dereference
  net: mvpp2: cls: fix less than zero check on a u32 variable
  net_sched: sch_fq: handle non connected flows
  net_sched: sch_fq: do not assume EDT packets are ordered
  net: hns3: use devm_kcalloc when allocating desc_cb
  net: hns3: some cleanup for struct hns3_enet_ring
  ...

Pull crypto update from Herbert Xu:
 "API:
   - Add support for AEAD in simd
   - Add fuzz testing to testmgr
   - Add panic_on_fail module parameter to testmgr
   - Use per-CPU struct instead multiple variables in scompress
   - Change verify API for akcipher

  Algorithms:
   - Convert x86 AEAD algorithms over to simd
   - Forbid 2-key 3DES in FIPS mode
   - Add EC-RDSA (GOST 34.10) algorithm

  Drivers:
   - Set output IV with ctr-aes in crypto4xx
   - Set output IV in rockchip
   - Fix potential length overflow with hashing in sun4i-ss
   - Fix computation error with ctr in vmx
   - Add SM4 protected keys support in ccree
   - Remove long-broken mxc-scc driver
   - Add rfc4106(gcm(aes)) cipher support in cavium/nitrox"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (179 commits)
  crypto: ccree - use a proper le32 type for le32 val
  crypto: ccree - remove set but not used variable 'du_size'
  crypto: ccree - Make cc_sec_disable static
  crypto: ccree - fix spelling mistake "protedcted" -> "protected"
  crypto: caam/qi2 - generate hash keys in-place
  crypto: caam/qi2 - fix DMA mapping of stack memory
  crypto: caam/qi2 - fix zero-length buffer DMA mapping
  crypto: stm32/cryp - update to return iv_out
  crypto: stm32/cryp - remove request mutex protection
  crypto: stm32/cryp - add weak key check for DES
  crypto: atmel - remove set but not used variable 'alg_name'
  crypto: picoxcell - Use dev_get_drvdata()
  crypto: crypto4xx - get rid of redundant using_sd variable
  crypto: crypto4xx - use sync skcipher for fallback
  crypto: crypto4xx - fix cfb and ofb "overran dst buffer" issues
  crypto: crypto4xx - fix ctr-aes missing output IV
  crypto: ecrdsa - select ASN1 and OID_REGISTRY for EC-RDSA
  crypto: ux500 - use ccflags-y instead of CFLAGS_<basename>.o
  crypto: ccree - handle tee fips error during power management resume
  crypto: ccree - add function to handle cryptocell tee fips error
  ...

This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.

The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.

This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.

Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64)                                  0.352340
= Note: Bluetooth subsystem version 2.22                               0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0)               [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84                                 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm)                      [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14                  {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14                {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1       {0x0003} [hci0] 27.302310
        Address type: 0x06
          LE Public
          LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6   #1 [hci0] 27.302496
        Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4                 #2 [hci0] 27.419117
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7  #3 [hci0] 27.419244
        Type: Active (0x01)
        Interval: 11.250 msec (0x0012)
        Window: 11.250 msec (0x0012)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #4 [hci0] 27.420131
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2      #5 [hci0] 27.420259
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                 #6 [hci0] 27.420969
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #7 [hci0] 27.421983
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4        {0x0003} [hci0] 27.422059
      Start Discovery (0x0023) plen 1
        Status: Success (0x00)
        Address type: 0x06
          LE Public
          LE Random
@ MGMT Event: Discovering (0x0013) plen 2             {0x0003} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0002} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0001} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

The flags field in 'struct shash_desc' never actually does anything.
The only ostensibly supported flag is CRYPTO_TFM_REQ_MAY_SLEEP.
However, no shash algorithm ever sleeps, making this flag a no-op.

With this being the case, inevitably some users who can't sleep wrongly
pass MAY_SLEEP.  These would all need to be fixed if any shash algorithm
actually started sleeping.  For example, the shash_ahash_*() functions,
which wrap a shash algorithm with the ahash API, pass through MAY_SLEEP
from the ahash API to the shash API.  However, the shash functions are
called under kmap_atomic(), so actually they're assumed to never sleep.

Even if it turns out that some users do need preemption points while
hashing large buffers, we could easily provide a helper function
crypto_shash_update_large() which divides the data into smaller chunks
and calls crypto_shash_update() and cond_resched() for each chunk.  It's
not necessary to have a flag in 'struct shash_desc', nor is it necessary
to make individual shash algorithms aware of this at all.

Therefore, remove shash_desc::flags, and document that the
crypto_shash_*() functions can be called from any context.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When flag HCI_QUIRK_USE_BDADDR_PROPERTY is set, we will read the
bluetooth address from dts. If the bluetooth address node is missing
from the dts we will enable it controller UNCONFIGURED state.
This patch enables the normal flow even if the BD address is missing
from the dts tree.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In ext_adv_report_event rssi comes before data (not after data as
in legacy adv_report_evt) so "+ 1" is not required in the ptr arithmatic
to point to next report.

Signed-off-by: Jaganath Kanakkassery <jaganath.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Struct ca is copied from userspace. It is not checked whether the "name"
field is NULL terminated, which allows local users to obtain potentially
sensitive information from kernel stack memory, via a HIDPCONNADD command.

This vulnerability is similar to CVE-2011-1079.

Signed-off-by: Young Xiao <YangX92@hotmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org