Pull SCSI fixes from James Bottomley:

 - a couple of serious fixes: use after free and blacklist for WRITE
   SAME

 - one error leg fix: write_pending failure

 - one user experience problem: do not override max_sectors_kb

 - one minor unused function removal

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ibmvscsis: Fix write_pending failure path
  scsi: libiscsi: Remove iscsi_destroy_session
  scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
  scsi: sd: Do not override max_sectors_kb sysfs setting
  scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP

Pull MMC fixes from Ulf Hansson:
 "MMC core:

   - Fix driver strength selection when selecting hs400es

   - Delete bounce buffer handling:

     This change fixes a problem related to how bounce buffers are being
     allocated. However, instead of trying to fix that, let's just
     remove the mmc bounce buffer code altogether, as it has practically
     no use.

  MMC host:

   - meson-gx: A couple of fixes related to clock/phase/tuning

   - sdhci-xenon: Fix clock resource by adding an optional bus clock"

* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
  mmc: meson-gx: include tx phase in the tuning process
  mmc: meson-gx: fix rx phase reset
  mmc: meson-gx: make sure the clock is rounded down
  mmc: Delete bounce buffer handling
  mmc: core: add driver strength selection when selecting hs400es

Pull watchddog clean-up and fixes from Thomas Gleixner:
 "The watchdog (hard/softlockup detector) code is pretty much broken in
  its current state. The patch series addresses this by removing all
  duct tape and refactoring it into a workable state.

  The reasons why I ask for inclusion that late in the cycle are:

   1) The code causes lockdep splats vs. hotplug locking which get
      reported over and over. Unfortunately there is no easy fix.

   2) The risk of breakage is minimal because it's already broken

   3) As 4.14 is a long term stable kernel, I prefer to have working
      watchdog code in that and the lockdep issues resolved. I wouldn't
      ask you to pull if 4.14 wouldn't be a LTS kernel or if the
      solution would be easy to backport.

   4) The series was around before the merge window opened, but then got
      delayed due to the UP failure caused by the for_each_cpu()
      surprise which we discussed recently.

  Changes vs. V1:

   - Addressed your review points

   - Addressed the warning in the powerpc code which was discovered late

   - Changed two function names which made sense up to a certain point
     in the series. Now they match what they do in the end.

   - Fixed a 'unused variable' warning, which got not detected by the
     intel robot. I triggered it when trying all possible related config
     combinations manually. Randconfig testing seems not random enough.

  The changes have been tested by and reviewed by Don Zickus and tested
  and acked by Micheal Ellerman for powerpc"

* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  watchdog/core: Put softlockup_threads_initialized under ifdef guard
  watchdog/core: Rename some softlockup_* functions
  powerpc/watchdog: Make use of watchdog_nmi_probe()
  watchdog/core, powerpc: Lock cpus across reconfiguration
  watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
  watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
  watchdog/hardlockup/perf: Cure UP damage
  watchdog/hardlockup: Clean up hotplug locking mess
  watchdog/hardlockup/perf: Simplify deferred event destroy
  watchdog/hardlockup/perf: Use new perf CPU enable mechanism
  watchdog/hardlockup/perf: Implement CPU enable replacement
  watchdog/hardlockup/perf: Implement init time detection of perf
  watchdog/hardlockup/perf: Implement init time perf validation
  watchdog/core: Get rid of the racy update loop
  watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
  watchdog/sysctl: Clean up sysctl variable name space
  watchdog/sysctl: Get rid of the #ifdeffery
  watchdog/core: Clean up header mess
  watchdog/core: Further simplify sysctl handling
  watchdog/core: Get rid of the thread teardown/setup dance
  ...

Pull device mapper fixes from Mike Snitzer:

 - a stable fix for the alignment of the event number reported at the
   end of the 'DM_LIST_DEVICES' ioctl.

 - a couple stable fixes for the DM crypt target.

 - a DM raid health status reporting fix.

* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm raid: fix incorrect status output at the end of a "recover" process
  dm crypt: reject sector_size feature if device length is not aligned to it
  dm crypt: fix memory leak in crypt_ctr_cipher_old()
  dm ioctl: fix alignment of event number in the device list

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes, mostly with stable ones:

 - X32 ABI fix for PCM; likely not so many people suffer from it, but
   still better to fix

 - Two minor kernel warning fixes on USB audio devices spotted by
   syzkaller

 - Regression fix of echoaudio due to its inconsistent dimension

 - Fix for HBR support on Intel DP audio, on some recent chips

 - USB-audio quirk for yet another Plantronics devices

 - Fix for potential double-fetch in ASIHPI FIFO queue"

* tag 'sound-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usx2y: Suppress kernel warning at page allocation failures
  Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members"
  ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptor
  ALSA: pcm: Fix structure definition for X32 ABI
  ALSA: usb-audio: Add sample rate quirk for Plantronics C310/C520-M
  ALSA: hda - program ICT bits to support HBR audio
  ALSA: asihpi: fix a potential double-fetch bug when copying puhm
  ALSA: compress: Remove unused variable

Pull networking fixes from David Miller:

 1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
    from Sara Sharon.

 2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
    Kasiviswanathan.

 3) Fix session and tunnel release races in l2tp, from Guillaume Nault
    and Sabrina Dubroca.

 4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.

 5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
    cap check, invalid memory access in IPoIB support, etc.)

 6) tun_get_user() should bail if skb->len is zero, from Alexander
    Potapenko.

 7) Fix RCU lookups in inetpeer, from Eric Dumazet.

 8) Fix locking in packet_do_bund().

 9) Handle cb->start() error properly in netlink dump code, from Jason
    A. Donenfeld.

10) Handle multicast properly in UDP socket early demux code. From Paolo
    Abeni.

11) Several erspan bug fixes in ip_gre, from Xin Long.

12) Fix use-after-free in socket filter code, in order to handle the
    fact that listener lock is no longer taken during the three-way TCP
    handshake. From Eric Dumazet.

13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.

14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
  net: 8021q: skip packets if the vlan is down
  bpf: fix bpf_tail_call() x64 JIT
  net: stmmac: dwmac-rk: Add RK3128 GMAC support
  rndis_host: support Novatel Verizon USB730L
  net: rtnetlink: fix info leak in RTM_GETSTATS call
  socket, bpf: fix possible use after free
  mlxsw: spectrum_router: Track RIF of IPIP next hops
  mlxsw: spectrum_router: Move VRF refcounting
  net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
  net: mvpp2: Fix clock resource by adding an optional bus clock
  r8152: add Linksys USB3GIGV1 id
  l2tp: fix l2tp_eth module loading
  ip_gre: erspan device should keep dst
  ip_gre: set tunnel hlen properly in erspan_tunnel_init
  ip_gre: check packet length and mtu correctly in erspan_xmit
  ip_gre: get key from session_id correctly in erspan_rcv
  tipc: use only positive error codes in messages
  ppp: fix __percpu annotation
  udp: perform source validation for mcast early demux
  IPv4: early demux can return an error code
  ...

Pull ARM SoC fixes from Olof Johansson:
 "Our first batch of fixes this release cycle, unfortunately a bit
  noisier than usual. Two major groups stand out:

   - Some pinctril dts/dtsi changes for stm32 due to a new driver being
     merged during the merge window, and this aligns the DT contents
     between the old format and the new. This could arguably be moved to
     the next merge window but it also seemed relatively harmless to
     include now.

   - Amlogic/meson had driver changes merged that required devicetree
     changes to avoid functional/performance regressions. I've already
     asked them to be more careful about this going forward, and making
     sure drivers are compatible with older DTs when they make these
     kind of changes. The platform is actively being upstreamed so
     there's a few things in flight, we've seen this happen before and
     sometimes it's hard to catch in time.

  Besides that there is the usual mix of minor fixes"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
  ARM: dts: stm32: use right pinctrl compatible for stm32f469
  ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
  ARM: defconfig: update Gemini defconfig
  ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
  arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
  reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
  ARM: dts: da850-evm: add serial and ethernet aliases
  ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
  ARM: dts: am33xx: Add spi alias to match SOC schematics
  ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
  ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
  ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
  ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
  arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
  arm64: dt marvell: Fix AP806 system controller size
  MAINTAINERS: add Macchiatobin maintainers entry
  ARC: reset: remove the misleading v1 suffix all over
  ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
  ARC: reset: Only build on archs that have IOMEM
  ARM: at91: Replace uses of virt_to_phys with __pa_symbol
  ...

The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu()
on powerpc because it is called multiple times for the boot CPU.

The first call is via:

  start_wd_on_cpu+0x80/0x2f0
  watchdog_nmi_reconfigure+0x124/0x170
  softlockup_reconfigure_threads+0x110/0x130
  lockup_detector_init+0xbc/0xe0
  kernel_init_freeable+0x18c/0x37c
  kernel_init+0x2c/0x160
  ret_from_kernel_thread+0x5c/0xbc

And then again via the CPU hotplug registration:

  start_wd_on_cpu+0x80/0x2f0
  cpuhp_invoke_callback+0x194/0x620
  cpuhp_thread_fun+0x7c/0x1b0
  smpboot_thread_fn+0x290/0x2a0
  kthread+0x168/0x1b0
  ret_from_kernel_thread+0x5c/0xbc

This can be avoided by setting up the cpu hotplug state with nocalls and
move the initialization to the watchdog_nmi_probe() function. That
initializes the hotplug callbacks without invoking the callback and the
following core initialization function then configures the watchdog for the
online CPUs (in this case CPU0) via softlockup_reconfigure_threads().

Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org

The recent cleanup of the watchdog code split watchdog_nmi_reconfigure()
into two stages. One to stop the NMI and one to restart it after
reconfiguration. That was done by adding a boolean 'run' argument to the
code, which is functionally correct but not necessarily a piece of art.

Replace it by two explicit functions: watchdog_nmi_stop() and
watchdog_nmi_start().

Fixes: 6592ad2fcc8f ("watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage")
Requested-by: Linus 'Nursing his pet-peeve' Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas 'Mopping up garbage' Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710021957480.2114@nanos

In may, Steven sent a patch deleting the bounce buffer handling
and the CONFIG_MMC_BLOCK_BOUNCE option.

I chose the less invasive path of making it a runtime config
option, and we merged that successfully for kernel v4.12.

The code is however just standing in the way and taking up
space for seemingly no gain on any systems in wide use today.

Pierre says the code was there to improve speed on TI SDHCI
controllers on certain HP laptops and possibly some Ricoh
controllers as well. Early SDHCI controllers lacked the
scatter-gather feature, which made software bounce buffers
a significant speed boost.

We are clearly talking about the list of SDHCI PCI-based
MMC/SD card readers found in the pci_ids[] list in
drivers/mmc/host/sdhci-pci-core.c.

The TI SDHCI derivative is not supported by the upstream
kernel. This leaves the Ricoh.

What we can however notice is that the x86 defconfigs in the
kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which
means that any such laptop would have to have a custom
configured kernel to actually take advantage of this
bounce buffer speed-up. It simply seems like there was
a speed optimization for the Ricoh controllers that noone
was using. (I have not checked the distro defconfigs but
I am pretty sure the situation is the same there.)

Bounce buffers increased performance on the OMAP HSMMC
at one point, and was part of the original submission in
commit a45c6cb81647 ("[ARM] 5369/1: omap mmc: Add new
   omap hsmmc controller for 2430 and 34xx, v3")

This optimization was removed in
commit 0ccd76d4c236 ("omap_hsmmc: Implement scatter-gather
   emulation")
which found that scatter-gather emulation provided even
better performance.

The same was introduced for SDHCI in
commit 2134a922c6e7 ("sdhci: scatter-gather (ADMA) support")

I am pretty positively convinced that software
scatter-gather emulation will do for any host controller what
the bounce buffers were doing. Essentially, the bounce buffer
was a reimplementation of software scatter-gather-emulation in
the MMC subsystem, and it should be done away with.

Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Suggested-by: Steven J. Hill <Steven.Hill@cavium.com>
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>