linux.git/include/linux/qed, branch v4.14-rc4

qed: enhanced per queue max coalesce value.

2017-07-27T07:05:22+00:00

Maximum coalesce per Rx/Tx queue is extended from
255 to 511.

Signed-off-by: Rahul Verma 
Signed-off-by: Yuval Mintz 
Signed-off-by: David S. Miller

qed: Read per queue coalesce from hardware

2017-07-27T07:05:22+00:00

Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.

Signed-off-by: Rahul Verma 
Signed-off-by: Yuval Mintz 
Signed-off-by: David S. Miller

qed: Add support for vf coalesce configuration.

2017-07-27T07:05:22+00:00

This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.

Signed-off-by: Rahul Verma 
Signed-off-by: Yuval Mintz 
Signed-off-by: David S. Miller

qed: Add support for Energy efficient ethernet.

2017-07-27T07:05:22+00:00

The patch adds required driver support for reading/configuring the
Energy Efficient Ethernet (EEE) parameters.

Signed-off-by: Sudarsana Reddy Kalluru 
Signed-off-by: Yuval Mintz 
Signed-off-by: David S. Miller

qed: iWARP CM add error handling

2017-07-03T08:43:45+00:00

This patch introduces error handling for errors that occurred during
connection establishment.

Signed-off-by: Michal Kalderon 
Signed-off-by: Yuval Mintz 
Signed-off-by: Ariel Elior 
Signed-off-by: David S. Miller

qed: iWARP implement disconnect flows

2017-07-03T08:43:45+00:00

This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.

Signed-off-by: Michal Kalderon 
Signed-off-by: Yuval Mintz 
Signed-off-by: Ariel Elior 
Signed-off-by: David S. Miller

qed: iWARP CM add active side connect

2017-07-03T08:43:45+00:00

This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.

Signed-off-by: Michal Kalderon 
Signed-off-by: Yuval Mintz 
Signed-off-by: Ariel Elior 
Signed-off-by: David S. Miller

qed: iWARP CM add passive side connect

2017-07-03T08:43:45+00:00

This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.

Error handling is not part of this patch.

Signed-off-by: Michal Kalderon 
Signed-off-by: Yuval Mintz 
Signed-off-by: Ariel Elior 
Signed-off-by: David S. Miller

qed: iWARP CM add listener functions and initial SYN processing

2017-07-03T08:43:45+00:00

This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.

Signed-off-by: Michal Kalderon 
Signed-off-by: Yuval Mintz 
Signed-off-by: Ariel Elior 
Signed-off-by: David S. Miller

qed: Add iWARP support in ll2 connections

2017-07-03T08:43:44+00:00

Add a new connection type for iWARP ll2 connections for setting
correct ll2 filters and connection type to FW.

Signed-off-by: Michal Kalderon 
Signed-off-by: Yuval Mintz 
Signed-off-by: Ariel Elior 
Signed-off-by: David S. Miller