Some overlapping changes in the mlx5 driver.

A merge conflict resolution posted by Stephen Rothwell was used as a
guide.

Signed-off-by: David S. Miller <davem@davemloft.net>

Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.

A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.

Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.

At high level, the FPGA configuration space is divided such:
 0x00000000 - 0x007fffff is reserved for the SBU
 0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ...        is DDR memory

A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Previously, only mlx5_ib enabled RoCE on the port, but FPGA needs it as
well.
Add support for counting number of enables, so that FPGA and IB can work
in parallel and independently.
Program the HW to enable RoCE on the first enable call, and program to
disable RoCE on the last disable call.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Reserved GIDs are entries in the GID table in use by the mlx5_core
and its submodules (e.g. FPGA, SRIOV, E-Swtich, netdev).
The entries are reserved at the high indexes of the GID table.

A mlx5 submodule may reserve a certain amount of GIDs for its own use
during the load sequence by calling mlx5_core_reserve_gids, and must
also take care to un-reserve these GIDs when it closes.
Reservation is only allowed during the load sequence and before any
interfaces (e.g. mlx5_ib or mlx5_en) are up.

After reservation, a submodule may call mlx5_core_reserved_gid_alloc/
free to allocate entries from the reserved GIDs pool.

Reserve a GID table entry for every supported FPGA QP.

A later patch in the patchset will remove them from being reported to
IB core.
Another such patch will make use of these for FPGA QPs in Innova NIC.

Added lib/mlx5.h to serve as a library for mlx5 submodlues, and to
expose only public mlx5 API, more mlx5 library files will be added in
future submissions.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.

Fixes: 5e44fca50470 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

MCC (Management Component Control) allows to control a firmware
component update.

MCDA (Management Component Data Access) allows to read and write
a firmware component.

MCQI (Management Component Query Information) allows to query
information about firmware components.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add a new interface for commands execution that allows the
caller to wait for the command's completion in a busy-wait
loop (polling mode).

This is useful if we want to execute a command in a polling mode
while the driver is working in events mode for the rest of
the commands.
This interface will be used in the downstream patches.

Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.

Fixes: 9cba4ebcf374 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Mellanox Innova is a NIC with ConnectX and an FPGA on the same
board. The FPGA is a bump-on-the-wire and thus affects operation of
the mlx5_core driver on the ConnectX ASIC.

Add basic support for Innova in mlx5_core.

This allows using the Innova card as a regular NIC, by detecting
the FPGA capability bit, and verifying its load state before
initializing ConnectX interfaces.

Also detect FPGA fatal runtime failures and enter error state if
they ever happen.

All new FPGA-related logic is placed in its own subdirectory 'fpga',
which may be built by selecting CONFIG_MLX5_FPGA.
This prepares for further support of various Innova features in later
patchsets.
Additional details about hardware architecture will be provided as
more features get submitted.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>