CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ.  By default
is disabled for now and will be enabled later on.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the relevant flow steering device structs and commands to
support vport.
Update the flow steering core API to receive vport number.
Add ingress and egress ACL flow table name spaces.
Add ACL flow table support:
* ACL (Access Control List) flow table is a table that contains
only allow/drop steering rules.

* We have two types of ACL flow tables - ingress and egress.

* ACLs handle traffic sent from/to E-Switch FDB table, Ingress refers to
traffic sent from Vport to E-Switch and Egress refers to traffic sent
from E-Switch to vport.

* Ingress ACL flow table allow/drop rules is checked against traffic
sent from VF.

* Egress ACL flow table allow/drop rules is checked against traffic sent
to VF.

Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv4/ip_gre.c

Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5 devices (Connect-IB, ConnectX-4, ConnectX-4-LX) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)

So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.

Cc: linux-stable@vger.kernel.org
Reported-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagig@grimberg.me>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Now as rx-vlan offload can be disabled, packets can be received
with vlan tag not stripped, which means is_first_ethertype_ip will
return false, for that we need to check if the hardware reported
csum OK so we will report CHECKSUM_UNNECESSARY for those packets.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose link_down_events counter through ethtool -S.
This counter is read from PPort statistics, then proccessed and stored as
a special handling software counter.
This counter is stored along software counters since it is the only PPort
counter that it's size is not 64 bits.

Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Redesign ethtool statistics handling and reporting in the driver:
1. Move counters to a separate file (en_stats.h).
2. Remove unnecessary dependencies between stats and strings.
3. Use counter descriptors which hold a name and offset for each counter,
   and will be used to decide which counters will be exposed.

For example when adding a new software counter to ethtool, instead of:
1. Add to stats struct.
2. Add to strings struct in the same order.
3. Change macro defining number of software counters.
The only thing needed is to link the new counter to a counter descriptor.

VPort counters are a set of hardware traffic counters created automatically
for each virtual port opened.
PPort counters are a set of counters describing per physical port
performance statistics.
These counters are gathered from hardware register and divided to groups
according to different protocols.

Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce the feature of multi-packet WQE (RX Work Queue Element)
referred to as (MPWQE or Striding RQ), in which WQEs are larger
and serve multiple packets each.

Every WQE consists of many strides of the same size, every received
packet is aligned to a beginning of a stride and is written to
consecutive strides within a WQE.

In the regular approach, each regular WQE is big enough to be capable
of serving one received packet of any size up to MTU or 64K in case of
device LRO is enabled, making it very wasteful when dealing with
small packets or device LRO is enabled.

For its flexibility, MPWQE allows a better memory utilization
(implying improvements in CPU utilization and packet rate) as packets
consume strides according to their size, preserving the rest of
the WQE to be available for other packets.

MPWQE default configuration:
	Num of WQEs	= 16
	Strides Per WQE = 2048
	Stride Size	= 64 byte

The default WQEs memory footprint went from 1024*mtu (~1.5MB) to
16 * 2048 * 64 = 2MB per ring.
However, HW LRO can now be supported at no additional cost in memory
footprint, and hence we turn it on by default and get an even better
performance.

Performance tested on ConnectX4-Lx 50G.
To isolate the feature under test, the numbers below were measured with
HW LRO turned off. We verified that the performance just improves when
LRO is turned back on.

* Netperf single TCP stream:
- BW raised by 10-15% for representative packet sizes:
  default, 64B, 1024B, 1478B, 65536B.

* Netperf multi TCP stream:
- No degradation, line rate reached.

* Pktgen: packet rate raised by 2-10% for traffic of different message
sizes: 64B, 128B, 256B, 1024B, and 1500B.

* Pktgen: packet loss in bursts of small messages (64byte),
single stream:
- | num packets | packets loss before | packets loss after
  |     2K      |       ~ 1K          |       0
  |     8K      |       ~ 6K          |       0
  |     16K     |       ~13K          |       0
  |     32K     |       ~28K          |       0
  |     64K     |       ~57K          |     ~24K

As expected as the driver can receive as many small packets (<=64B) as
the number of total strides in the ring (default = 2048 * 16) vs. 1024
(default ring size regardless of packets size) before this feature.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more rdma updates from Doug Ledford:
 "Round two of 4.6 merge window patches.

  This is a monster pull request.  I held off on the hfi1 driver updates
  (the hfi1 driver is intimately tied to the qib driver and the new
  rdmavt software library that was created to help both of them) in my
  first pull request.  The hfi1/qib/rdmavt update is probably 90% of
  this pull request.  The hfi1 driver is being left in staging so that
  it can be fixed up in regards to the API that Al and yourself didn't
  like.  Intel has agreed to do the work, but in the meantime, this
  clears out 300+ patches in the backlog queue and brings my tree and
  their tree closer to sync.

  This also includes about 10 patches to the core and a few to mlx5 to
  create an infrastructure for configuring SRIOV ports on IB devices.
  That series includes one patch to the net core that we sent to netdev@
  and Dave Miller with each of the three revisions to the series.  We
  didn't get any response to the patch, so we took that as implicit
  approval.

  Finally, this series includes Intel's new iWARP driver for their x722
  cards.  It's not nearly the beast as the hfi1 driver.  It also has a
  linux-next merge issue, but that has been resolved and it now passes
  just fine.

  Summary:

   - A few minor core fixups needed for the next patch series

   - The IB SRIOV series.  This has bounced around for several versions.
     Of note is the fact that the first patch in this series effects the
     net core.  It was directed to netdev and DaveM for each iteration
     of the series (three versions total).  Dave did not object, but did
     not respond either.  I've taken this as permission to move forward
     with the series.

   - The new Intel X722 iWARP driver

   - A huge set of updates to the Intel hfi1 driver.  Of particular
     interest here is that we have left the driver in staging since it
     still has an API that people object to.  Intel is working on a fix,
     but getting these patches in now helps keep me sane as the upstream
     and Intel's trees were over 300 patches apart"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
  IB/ipoib: Allow mcast packets from other VFs
  IB/mlx5: Implement callbacks for manipulating VFs
  net/mlx5_core: Implement modify HCA vport command
  net/mlx5_core: Add VF param when querying vport counter
  IB/ipoib: Add ndo operations for configuring VFs
  IB/core: Add interfaces to control VF attributes
  IB/core: Support accessing SA in virtualized environment
  IB/core: Add subnet prefix to port info
  IB/mlx5: Fix decision on using MAD_IFC
  net/core: Add support for configuring VF GUIDs
  IB/{core, ulp} Support above 32 possible device capability flags
  IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
  net/mlx5_core: Introduce offload arithmetic hardware capabilities
  net/mlx5_core: Refactor device capability function
  net/mlx5_core: Fix caching ATOMIC endian mode capability
  ib_srpt: fix a WARN_ON() message
  i40iw: Replace the obsolete crypto hash interface with shash
  IB/hfi1: Add SDMA cache eviction algorithm
  IB/hfi1: Switch to using the pin query function
  IB/hfi1: Specify mm when releasing pages
  ...

Define the necessary hardware structures for the offload
arithmetic capabilities and read/cache them on driver load.

Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>