linux.git/include/linux/mlx4/cmd.h, branch v3.11-rc2

net/mlx4_core: Dynamic VST to VST vlan/qos changes

2013-07-01T20:10:22+00:00

Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.

This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).

To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.

If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.

Signed-off-by: Jack Morgenstein 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Add VF link state support

2013-06-14T00:51:04+00:00

Add support to change the link state of VF (vPort)

Signed-off-by: Rony Efraim 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Add support to get VF config

2013-04-27T03:29:14+00:00

Support getting VF config.

Signed-off-by: Rony Efraim 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Add VF MAC spoof checking support

2013-04-27T03:29:14+00:00

Add ndo_set_vf_spoofchk support

Signed-off-by: Rony Efraim 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Add set VF default vlan ID and priority support

2013-04-27T03:29:13+00:00

Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.

The special values of VID=4095 or VID=0,UP=0 are considered as VGT.

Signed-off-by: Rony Efraim 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4: Add set VF mac address support

2013-04-27T03:29:13+00:00

Add ndo_set_vf_mac support which allows to set the MAC address
for mlx4 VF Ethernet NICs from the host.

Signed-off-by: Rony Efraim 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4_core: Add firmware commands to support device managed flow steering

2012-07-07T23:23:05+00:00

Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.

Signed-off-by: Hadar Hen Zion 
Signed-off-by: Or Gerlitz 
Signed-off-by: David S. Miller

net/mlx4_core: set port QoS attributes

2012-04-05T09:08:03+00:00

Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number

Signed-off-by: Amir Vadai 
Signed-off-by: David S. Miller

mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet

2011-12-13T18:56:08+00:00

1. Added module parameters sr_iov and probe_vf for controlling enablement of
   SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
   SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
   ports configured as desired.
   In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
   for the case where the FW supports both port types (ETH and IB), the
   port_type_array parameter is used.
   By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
   to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
   mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
   modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
   VFs obtain their startup information from the PF (master) device via the
   comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
   aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership:  Currently, only one PF is supported by the driver.
   If the HCA is burned with FW which enables more than one PF, only one
   of the PFs is allowed to run.  The first one up grabs a FW ownership
   semaphone -- all other PFs will find that semaphore taken, and the
   driver will not allow them to run.

Signed-off-by: Jack Morgenstein 
Signed-off-by: Yevgeny Petrilin 
Signed-off-by: Liran Liss 
Signed-off-by: Marcel Apfelbaum 
Signed-off-by: David S. Miller

mlx4_core: Add "native" argument to mlx4_cmd and its callers (where needed)

2011-12-13T18:56:05+00:00

For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).

This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.

Note that if SRIOV is not activated, this parameter has no effect.

Signed-off-by: Jack Morgenstein 
Signed-off-by: David S. Miller