Some systems use the audio CODEC to clock a DAI with multiple data lines
in parallel, meaning that bit clocks are only required for a smaller number
of channels than data is sent for. In some cases providing the extra bit
clocks can take the other devices on the audio bus out of spec.

Support such systems by allowing a maximum number of channels to be
specified.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This can be used to provide some additional settling time to ensure that
we don't start microphone detection while the microphone pin is connected
to one of the headphone pins.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Pull MFD changes from Samuel Ortiz:
 - 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
   TI's TPS65090 and TPS65217.
 - New variants support (8420, 8520 ab9540), cleanups and bug fixes for
   the abx500 and db8500 ST-E chipsets.
 - Some minor fixes and update for the wm8994 from Mark.
 - The beginning of a long term TWL cleanup effort coming from the TI
   folks.
 - Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
   drivers.

Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).

* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
  gpio/twl: Add DT support to gpio-twl4030 driver
  gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
  mfd: Detach twl6040 from the pmic mfd driver
  mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
  mfd: Micro-optimization on twl4030 IRQ handler
  mfd: Make twl4030 SIH SPARSE_IRQ capable
  mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
  mfd: Remove references already defineid in header file from twl-core
  mfd: Remove unneeded header from twl-core
  mfd: Make twl-core not depend on pdata->irq_base/end
  ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
  mfd: Return twl6030_mmc_card_detect IRQ for board setup
  Revert "mfd: Add platform data for MAX8997 haptic driver"
  mfd: Add support for TPS65090
  mfd: Add some da9052-i2c section annotations
  mfd: Build rtc5t583 only if I2C config is selected to y.
  mfd: Add anatop mfd driver
  mfd: Fix compilation error in tps65910.h
  mfd: Add 8420 variant to db8500-prcmu
  mfd: Add 8520 PRCMU variant to db8500-prcmu
  ...

It's causing confusion with the regulator level field of the same name
and serves no useful function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>