linux.git/include/linux/if_vlan.h, branch v3.10-rc5

net: vlan: fix dummy function signatures for CONFIG_VLAN=n

2013-04-21T19:56:59+00:00

Fix up some function signatures for CONFIG_VLAN=n that were missed during
the 802.1ad support patches.

Found by the kbuild robot.

Signed-off-by: Patrick McHardy 
Signed-off-by: David S. Miller

net: vlan: add 802.1ad support

2013-04-19T18:46:06+00:00

Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.

Configuration is done using "ip link":

# ip link add link eth0 eth0.1000 \
	type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
	type vlan proto 802.1q id 1000

52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
    20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
    20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64

Signed-off-by: Patrick McHardy 
Signed-off-by: David S. Miller

net: vlan: add protocol argument to packet tagging functions

2013-04-19T18:46:06+00:00

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.

Signed-off-by: Patrick McHardy 
Signed-off-by: David S. Miller

net: vlan: prepare for 802.1ad support

2013-04-19T18:45:27+00:00

Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.

Signed-off-by: Patrick McHardy 
Signed-off-by: David S. Miller

net: vlan: prepare for 802.1ad VLAN filtering offload

2013-04-19T18:45:27+00:00

Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).

Signed-off-by: Patrick McHardy 
Signed-off-by: David S. Miller

net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*

2013-04-19T18:45:26+00:00

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.

Signed-off-by: Patrick McHardy 
Signed-off-by: David S. Miller

net: add ETH_P_802_3_MIN

2013-03-28T05:20:42+00:00

Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.

Also update all the users of this value that David Miller and
I could find to use the new constant.

Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.

As suggested by Jesse Gross.

Compile tested only.

Cc: David Miller 
Cc: Jesse Gross 
Cc: Karsten Keil 
Cc: John W. Linville 
Cc: Johannes Berg 
Cc: Bart De Schuymer 
Cc: Stephen Hemminger 
Cc: Patrick McHardy 
Cc: Marcel Holtmann 
Cc: Gustavo Padovan 
Cc: Johan Hedberg 
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab 
Acked-by: Stefan Richter 
Signed-off-by: Simon Horman 
Signed-off-by: David S. Miller

vlan: adjust vlan_set_encap_proto() for its callers

2013-02-24T02:00:06+00:00

There are two places to call vlan_set_encap_proto():
vlan_untag() and __pop_vlan_tci().

vlan_untag() assumes skb->data points after mac addr, otherwise
the following code

        vhdr = (struct vlan_hdr *) skb->data;
        vlan_tci = ntohs(vhdr->h_vlan_TCI);
        __vlan_hwaccel_put_tag(skb, vlan_tci);

        skb_pull_rcsum(skb, VLAN_HLEN);

won't be correct. But __pop_vlan_tci() assumes points _before_
mac addr.

In vlan_set_encap_proto(), it looks for some magic L2 value
after mac addr:

        rawp = skb->data;
        if (*(unsigned short *) rawp == 0xFFFF)
	...

Therefore __pop_vlan_tci() is obviously wrong.

A quick fix is avoiding using skb->data in vlan_set_encap_proto(),
use 'vhdr+1' is always correct in both cases.

Cc: David S. Miller 
Cc: Jesse Gross 
Signed-off-by: Cong Wang 
Acked-by: Jesse Gross 
Signed-off-by: David S. Miller

UAPI: (Scripted) Disintegrate include/linux

2012-10-13T09:46:48+00:00

Signed-off-by: David Howells 
Acked-by: Arnd Bergmann 
Acked-by: Thomas Gleixner 
Acked-by: Michael Kerrisk 
Acked-by: Paul E. McKenney 
Acked-by: Dave Jones

vlan: don't deliver frames for unknown vlans to protocols

2012-10-08T19:21:55+00:00

6a32e4f9dd9219261f8856f817e6655114cfec2f made the vlan code skip marking
vlan-tagged frames for not locally configured vlans as PACKET_OTHERHOST if
there was an rx_handler, as the rx_handler could cause the frame to be received
on a different (virtual) vlan-capable interface where that vlan might be
configured.

As rx_handlers do not necessarily return RX_HANDLER_ANOTHER, this could cause
frames for unknown vlans to be delivered to the protocol stack as if they had
been received untagged.

For example, if an ipv6 router advertisement that's tagged for a locally not
configured vlan is received on an interface with macvlan interfaces attached,
macvlan's rx_handler returns RX_HANDLER_PASS after delivering the frame to the
macvlan interfaces, which caused it to be passed to the protocol stack, leading
to ipv6 addresses for the announced prefix being configured even though those
are completely unusable on the underlying interface.

The fix moves marking as PACKET_OTHERHOST after the rx_handler so the
rx_handler, if there is one, sees the frame unchanged, but afterwards,
before the frame is delivered to the protocol stack, it gets marked whether
there is an rx_handler or not.

Signed-off-by: Florian Zumbiehl 
Signed-off-by: David S. Miller