linux.git/include/dt-bindings/power, branch v6.5 Linux kernel source tree Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc 2023-06-29T22:07:06+00:00 Linus Torvalds torvalds@linux-foundation.org 2023-06-29T22:07:06+00:00 6c1561fb900524c5bceb924071b3e9b8a67ff3da Pull ARM SoC devicetree updates from Arnd Bergmann: "The biggest change this time is for the 32-bit devicetree files, which are all moved to a new location, using separate subdirectories for each SoC vendor, following the same scheme that is used on arm64, mips and riscv. This has been discussed for many years, but so far we never did this as there was a plan to move the files out of the kernel entirely, which has never happened. The impact of this will be that all external patches no longer apply, and anything depending on the location of the dtb files in the build directory will have to change. The installed files after 'make dtbs_install' keep the current location. There are six added SoCs here that are largely variants of previously added chips. Two other chips are added in a separate branch along with their device drivers. - The Samsung Exynos 4212 makes its return after the Samsung Galaxy Express phone is addded at last. The SoC support was originally added in 2012 but removed again in 2017 as it was unused at the time. - Amlogic C3 is a Cortex-A35 based smart IP camera chip - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of the still common MSM8916 (Snapdragon 410) phone chip that has been supported for a long time. - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end laptop chips, used in the Lenovo Flex 5G, which is added along with the reference board. - Qualcomm SDX75 is the latest generation modem chip that is used as a peripherial in phones but can also run a standalone Linux. Unlike the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55. - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie C910 core, a step up from all previously added rv64 chips. All of the above come with reference board implementations, those included there are 39 new board files, but only five more 32-bit this time, probably a new low: - Marantec Maveo board based on dhcor imx6ull module - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip - Epson Moverio BT-200 AR glasses based on TI OMAP4 - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM - ICnova ADB4006 board based on Allwinner A20 On the 64-bit side, there are also fewer addded machines than we had in the recent releases: - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device. - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234 - Qualcomm gains support for 6 reference boards on various members of their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top of the various reference platforms for their new chips. - Rockchips support for several newer boards: Indiedroid Nova (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S (rk3568) - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin family with AM62 COM, carrier and dev boards Other changes to existing boards contain the usual minor improvements along with - continued updates to clean up dts files based on dtc warnings and binding checks, in particular cache properties and node names - support for devicetree overlays on at91, bcm283x - significant additions to existing SoC support on mediatek, qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1 As usual, a lot more detail is available in the individual merge commits" * tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits) ARM: mvebu: fix unit address on armada-390-db flash ARM: dts: Move .dts files to vendor sub-directories kbuild: Support flat DTBs install ARM: dts: Add .dts files missing from the build ARM: dts: allwinner: Use quoted #include ARM: dts: lan966x: kontron-d10: add PHY interrupts ARM: dts: lan966x: kontron-d10: fix SPI CS ARM: dts: lan966x: kontron-d10: fix board reset ARM: dts: at91: Enable device-tree overlay support for AT91 boards arm: dts: Enable device-tree overlay support for AT91 boards arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller ARM: dts: at91: use generic name for shutdown controller ARM: dts: BCM5301X: Add cells sizes to PCIe nodes dt-bindings: firmware: brcm,kona-smc: convert to YAML riscv: dts: sort makefile entries by directory riscv: defconfig: enable T-HEAD SoC MAINTAINERS: add entry for T-HEAD RISC-V SoC riscv: dts: thead: add sipeed Lichee Pi 4A board device tree riscv: dts: add initial T-HEAD TH1520 SoC device tree riscv: Add the T-HEAD SoC family Kconfig option ... 
Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...
dt-bindings: power: qcom,rpmpd: Add SA8155P 2023-05-25T03:34:49+00:00 Konrad Dybcio konrad.dybcio@linaro.org 2023-04-11T13:47:15+00:00 672b584c68de309017cd2ce8938856c9b7c1b70e Add a compatible for SA8155P platforms and relevant defines to the include file. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230411-topic-hanaau-v2-1-fd3d70844b31@linaro.org 
Add a compatible for SA8155P platforms and relevant defines to the
include file.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230411-topic-hanaau-v2-1-fd3d70844b31@linaro.org
dt-bindings: power: qcom,rpmpd: Format RPMh levels better 2023-05-18T02:25:48+00:00 Konrad Dybcio konrad.dybcio@linaro.org 2023-05-17T20:12:51+00:00 1738600082987ddcf9cfce753ae3c581c8e46933 After adding the missing levels with a nice, easy-to-read diff, reformat the defines to make them nice to look at.. Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-2-3063ce19c491@linaro.org 
After adding the missing levels with a nice, easy-to-read diff,
reformat the defines to make them nice to look at..

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-2-3063ce19c491@linaro.org
dt-bindings: power: qcom,rpmpd: add missing RPMH levels 2023-05-18T02:25:48+00:00 Konrad Dybcio konrad.dybcio@linaro.org 2023-05-17T20:12:50+00:00 4755e880b08d963db24a1b3a710ee0e62f36aa49 There are a lot of RPMh levels that we haven't included yet.. some sadly turned out to be necessary, add them! Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-1-3063ce19c491@linaro.org 
There are a lot of RPMh levels that we haven't included yet.. some
sadly turned out to be necessary, add them!

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517-topic-kailua-rpmhpd-v2-1-3063ce19c491@linaro.org
soc: renesas: rcar-sysc: Remove R-Car H3 ES1.* handling 2023-03-10T15:31:07+00:00 Wolfram Sang wsa+renesas@sang-engineering.com 2023-03-07T10:56:40+00:00 fd9c55c0acac59013dae9f8eedb0e0eb2e82e276 R-Car H3 ES1.* was only available to an internal development group and needed a lot of quirks and workarounds. These become a maintenance burden now, so our development group decided to remove upstream support and disable booting for this SoC. Public users only have ES2 onwards. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20230307105645.5285-5-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> 
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds.  These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC.  Public users only have ES2 onwards.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230307105645.5285-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc 2023-02-27T18:04:49+00:00 Linus Torvalds torvalds@linux-foundation.org 2023-02-27T18:04:49+00:00 11c70529983e8136ea1bd5c32e4f9cd14503c644 Pull ARM SoC driver updates from Arnd Bergmann: "As usual, there are lots of minor driver changes across SoC platforms from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung. These usually add support for additional chip variations in existing drivers, but also add features or bugfixes. The SCMI firmware subsystem gains a unified raw userspace interface through debugfs, which can be used for validation purposes. Newly added drivers include: - New power management drivers for StarFive JH7110, Allwinner D1 and Renesas RZ/V2M - A driver for Qualcomm battery and power supply status - A SoC device driver for identifying Nuvoton WPCM450 chips - A regulator coupler driver for Mediatek MT81xxv" * tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits) power: supply: Introduce Qualcomm PMIC GLINK power supply soc: apple: rtkit: Do not copy the reg state structure to the stack soc: sunxi: SUN20I_PPU should depend on PM memory: renesas-rpc-if: Remove redundant division of dummy soc: qcom: socinfo: Add IDs for IPQ5332 and its variant dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1 firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/ MAINTAINERS: Update qcom CPR maintainer entry dt-bindings: firmware: document Qualcomm SM8550 SCM dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants soc: qcom: socinfo: Add support for new field in revision 17 soc: qcom: smd-rpm: Add IPQ9574 compatible soc: qcom: pmic_glink: remove redundant calculation of svid soc: qcom: stats: Populate all subsystem debugfs files dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies soc: qcom: pmic_glink: Introduce altmode support ... 
Pull ARM SoC driver updates from Arnd Bergmann:
 "As usual, there are lots of minor driver changes across SoC platforms
  from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
  These usually add support for additional chip variations in existing
  drivers, but also add features or bugfixes.

  The SCMI firmware subsystem gains a unified raw userspace interface
  through debugfs, which can be used for validation purposes.

  Newly added drivers include:

   - New power management drivers for StarFive JH7110, Allwinner D1 and
     Renesas RZ/V2M

   - A driver for Qualcomm battery and power supply status

   - A SoC device driver for identifying Nuvoton WPCM450 chips

   - A regulator coupler driver for Mediatek MT81xxv"

* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  power: supply: Introduce Qualcomm PMIC GLINK power supply
  soc: apple: rtkit: Do not copy the reg state structure to the stack
  soc: sunxi: SUN20I_PPU should depend on PM
  memory: renesas-rpc-if: Remove redundant division of dummy
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  ...
Merge tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers 2023-02-13T15:22:33+00:00 Arnd Bergmann arnd@arndb.de 2023-02-13T15:22:32+00:00 68907175ec5e6a240e724a8e3fa0064baf392b4c More Qualcomm driver updates for 6.3 The qcom_scm.h file is moved into firmware/qcom, to avoid having any Qualcomm-specific files directly in include/linux. Support for PMIC GLINK is introduced, which on newer Qualcomm platforms provides an interface to the firmware implementing battery management and USB Type-C handling. Together with the base driver comes the custom altmode support driver. SMD RPM gains support for IPQ9574, and socinfo is extended with support for revision 17 of the information format and soc_id for IPQ5332 and IPQ8064 are added. The qcom_stats is changes not to fail when not all parts are initialized. * tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: soc: qcom: socinfo: Add IDs for IPQ5332 and its variant dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1 firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/ MAINTAINERS: Update qcom CPR maintainer entry dt-bindings: firmware: document Qualcomm SM8550 SCM dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants soc: qcom: socinfo: Add support for new field in revision 17 soc: qcom: smd-rpm: Add IPQ9574 compatible soc: qcom: pmic_glink: remove redundant calculation of svid soc: qcom: stats: Populate all subsystem debugfs files dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies soc: qcom: pmic_glink: Introduce altmode support soc: qcom: pmic_glink: Introduce base PMIC GLINK driver dt-bindings: soc: qcom: Introduce PMIC GLINK binding soc: qcom: dcc: Drop driver for now Link: https://lore.kernel.org/r/20230210182242.2023901-1-andersson@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> 
More Qualcomm driver updates for 6.3

The qcom_scm.h file is moved into firmware/qcom, to avoid having any
Qualcomm-specific files directly in include/linux.

Support for PMIC GLINK is introduced, which on newer Qualcomm platforms
provides an interface to the firmware implementing battery management
and USB Type-C handling. Together with the base driver comes the custom
altmode support driver.

SMD RPM gains support for IPQ9574, and socinfo is extended with support
for revision 17 of the information format and soc_id for IPQ5332 and
IPQ8064 are added.

The qcom_stats  is changes not to fail when not all parts are
initialized.

* tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
  dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
  dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
  firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
  MAINTAINERS: Update qcom CPR maintainer entry
  dt-bindings: firmware: document Qualcomm SM8550 SCM
  dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
  soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
  dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
  soc: qcom: socinfo: Add support for new field in revision 17
  soc: qcom: smd-rpm: Add IPQ9574 compatible
  soc: qcom: pmic_glink: remove redundant calculation of svid
  soc: qcom: stats: Populate all subsystem debugfs files
  dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
  soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
  soc: qcom: pmic_glink: Introduce altmode support
  soc: qcom: pmic_glink: Introduce base PMIC GLINK driver
  dt-bindings: soc: qcom: Introduce PMIC GLINK binding
  soc: qcom: dcc: Drop driver for now

Link: https://lore.kernel.org/r/20230210182242.2023901-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge tag 'qcom-drivers-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers 2023-02-13T15:21:41+00:00 Arnd Bergmann arnd@arndb.de 2023-02-13T15:19:55+00:00 01e9d2c6bea9823103958bd3d71f61b9900ef5be Qualcomm driver updates for v6.3 This introduces a new driver for the Data Capture and Compare block, which provides a mechanism for capturing hardware state (access MMIO registers) either upon request of triggered automatically e.g. upon a watchdog bite, for post mortem analysis. The remote filesystem memory share driver gains support for having its memory bound to more than a single VMID. The SCM driver gains the minimal support needed to support a new mechanism where secure world can put calls on hold and later request them to be retried. Support for the new SA8775P platform is added to rpmhpd, QDU1000 is added to the SCM driver and a long list of platforms are added to the socinfo driver. Support for socinfo data revision 16 is also introduced. Lastly a driver to program the ramp controller in MSM8976 is introduced. * tag 'qcom-drivers-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits) firmware: qcom: scm: Add wait-queue handling logic dt-bindings: firmware: qcom,scm: Add optional interrupt Revert "dt-bindings: power: rpmpd: Add SM4250 support" Revert "soc: qcom: rpmpd: Add SM4250 support" soc: qcom: socinfo: Add a bunch of older SoCs dt-bindings: arm: qcom,ids: Add a bunch of older SoCs dt-bindings: arm: qcom,ids: Add QRD board ID soc: qcom: socinfo: Fix soc_id order dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels dt-bindings: firmware: qcom: scm: Separate VMIDs from header to bindings soc: qcom: rmtfs: Optionally map RMTFS to more VMs dt-bindings: reserved-memory: rmtfs: Make qcom,vmid an array dt-bindings: firmware: scm: Add QDU1000/QRU1000 compatible dt-bindings: firmware: qcom,scm: narrow clocks and interconnects dt-bindings: firmware: qcom,scm: document MSM8226 clocks soc: qcom: ramp_controller: Make things static soc: qcom: rmphpd: add power domains for sa8775p dt-bindings: power: qcom,rpmpd: document sa8775p PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe() soc: qcom: dcc: rewrite description of dcc sysfs files ... Link: https://lore.kernel.org/r/20230126163008.3676950-1-andersson@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> 
Qualcomm driver updates for v6.3

This introduces a new driver for the Data Capture and Compare block,
which provides a mechanism for capturing hardware state (access MMIO
registers) either upon request of triggered automatically e.g. upon a
watchdog bite, for post mortem analysis.

The remote filesystem memory share driver gains support for having its
memory bound to more than a single VMID.

The SCM driver gains the minimal support needed to support a new
mechanism where secure world can put calls on hold and later request
them to be retried.

Support for the new SA8775P platform is added to rpmhpd, QDU1000 is
added to the SCM driver and a long list of platforms are added to the
socinfo driver. Support for socinfo data revision 16 is also introduced.

Lastly a driver to program the ramp controller in MSM8976 is introduced.

* tag 'qcom-drivers-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
  firmware: qcom: scm: Add wait-queue handling logic
  dt-bindings: firmware: qcom,scm: Add optional interrupt
  Revert "dt-bindings: power: rpmpd: Add SM4250 support"
  Revert "soc: qcom: rpmpd: Add SM4250 support"
  soc: qcom: socinfo: Add a bunch of older SoCs
  dt-bindings: arm: qcom,ids: Add a bunch of older SoCs
  dt-bindings: arm: qcom,ids: Add QRD board ID
  soc: qcom: socinfo: Fix soc_id order
  dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels
  dt-bindings: firmware: qcom: scm: Separate VMIDs from header to bindings
  soc: qcom: rmtfs: Optionally map RMTFS to more VMs
  dt-bindings: reserved-memory: rmtfs: Make qcom,vmid an array
  dt-bindings: firmware: scm: Add QDU1000/QRU1000 compatible
  dt-bindings: firmware: qcom,scm: narrow clocks and interconnects
  dt-bindings: firmware: qcom,scm: document MSM8226 clocks
  soc: qcom: ramp_controller: Make things static
  soc: qcom: rmphpd: add power domains for sa8775p
  dt-bindings: power: qcom,rpmpd: document sa8775p
  PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
  soc: qcom: dcc: rewrite description of dcc sysfs files
  ...

Link: https://lore.kernel.org/r/20230126163008.3676950-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1 2023-02-09T03:29:46+00:00 Dmitry Baryshkov dmitry.baryshkov@linaro.org 2023-02-06T14:57:01+00:00 bdd133c2eeffad142e7c8a48ab7e86e1ca37e67d Add define for another power saving state used on SM8350 for the GPU. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230206145707.122937-3-dmitry.baryshkov@linaro.org 
Add define for another power saving state used on SM8350 for the GPU.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206145707.122937-3-dmitry.baryshkov@linaro.org
Merge tag 'v6.2-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into soc/drivers 2023-02-03T13:22:19+00:00 Arnd Bergmann arnd@arndb.de 2023-02-03T13:22:02+00:00 426082a214db267f44b3077c9e2cae9e1baaaa91 Introduce MediaTek regulator coupler driver to ensure that the SRAM voltage in par with the GPU voltage. This allows for a stable use of the GPU. mtk-mutex: - add support for MT8188 vdosys0 path - allow it to be build as module - add support for MT8195 vdosys1 path mmsys: - add MT8188 vdosys0 path - allow to be build as a module - add MT8195 vdosys1 path - add support for CMDQ - allow for up to 64 reset bits - add supprot for the MT8195 vppsys[0,1] pathes pm-domains: - keep power for the MT8186 ADSP on by default - add support for MT8188 - add support for buck isolation needed in specific pm-domains for MT8188 and MT8192 mtk-svs: - enable IRQ later to allow using kexec - several improvments on the code base - fix modalias pmic wrapper: - convert binding to yaml. As this is thightly coupled to the MT6357 PMIC, I took patches regarding it as well. * tag 'v6.2-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (41 commits) soc: mediatek: mtk-svs: add missing MODULE_DEVICE_TABLE soc: mediatek: mtk-devapc: Switch to devm_clk_get_enabled() soc: mtk-svs: mt8183: refactor o_slope calculation soc: mediatek: mtk-svs: delete superfluous platform data entries soc: mediatek: mtk-svs: move svs_platform_probe into probe soc: mediatek: mtk-svs: improve readability of platform_probe soc: mediatek: mtk-svs: clean up platform probing soc: mediatek: mtk-svs: keep svs alive if CONFIG_DEBUG_FS not supported soc: mediatek: mtk-svs: Use pm_runtime_resume_and_get() in svs_init01() soc: mediatek: mtk-svs: reset svs when svs_resume() fail soc: mediatek: mtk-svs: restore default voltages when svs_init02() fail soc: mediatek: mmsys: add support for MT8195 VPPSYS dt-bindings: arm: mediatek: mmsys: Add support for MT8195 VPPSYS soc: mediatek: Introduce mediatek-regulator-coupler driver soc: mediatek: mtk-svs: Enable the IRQ later soc: mediatek: add mtk-mutex support for mt8195 vdosys1 soc: mediatek: add mtk-mutex component - dp_intf1 soc: mediatek: mmsys: add reset control for MT8195 vdosys1 soc: mediatek: mmsys: add mmsys for support 64 reset bits soc: mediatek: add cmdq support of mtk-mmsys config API for mt8195 vdosys1 ... Link: https://lore.kernel.org/r/396d51fc-81f3-4a2b-d7a7-b966bfe3002a@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de> 
Introduce MediaTek regulator coupler driver to ensure that the SRAM
voltage in par with the GPU voltage. This allows for a stable use of the
GPU.

mtk-mutex:
- add support for MT8188 vdosys0 path
- allow it to be build as module
- add support for MT8195 vdosys1 path

mmsys:
- add MT8188 vdosys0 path
- allow to be build as a module
- add MT8195 vdosys1 path
- add support for CMDQ
- allow for up to 64 reset bits
- add supprot for the MT8195 vppsys[0,1] pathes

pm-domains:
- keep power for the MT8186 ADSP on by default
- add support for MT8188
- add support for buck isolation needed in specific pm-domains for
  MT8188 and MT8192

mtk-svs:
- enable IRQ later to allow using kexec
- several improvments on the code base
- fix modalias

pmic wrapper:
- convert binding to yaml. As this is thightly coupled to the MT6357
  PMIC, I took patches regarding it as well.

* tag 'v6.2-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (41 commits)
  soc: mediatek: mtk-svs: add missing MODULE_DEVICE_TABLE
  soc: mediatek: mtk-devapc: Switch to devm_clk_get_enabled()
  soc: mtk-svs: mt8183: refactor o_slope calculation
  soc: mediatek: mtk-svs: delete superfluous platform data entries
  soc: mediatek: mtk-svs: move svs_platform_probe into probe
  soc: mediatek: mtk-svs: improve readability of platform_probe
  soc: mediatek: mtk-svs: clean up platform probing
  soc: mediatek: mtk-svs: keep svs alive if CONFIG_DEBUG_FS not supported
  soc: mediatek: mtk-svs: Use pm_runtime_resume_and_get() in svs_init01()
  soc: mediatek: mtk-svs: reset svs when svs_resume() fail
  soc: mediatek: mtk-svs: restore default voltages when svs_init02() fail
  soc: mediatek: mmsys: add support for MT8195 VPPSYS
  dt-bindings: arm: mediatek: mmsys: Add support for MT8195 VPPSYS
  soc: mediatek: Introduce mediatek-regulator-coupler driver
  soc: mediatek: mtk-svs: Enable the IRQ later
  soc: mediatek: add mtk-mutex support for mt8195 vdosys1
  soc: mediatek: add mtk-mutex component - dp_intf1
  soc: mediatek: mmsys: add reset control for MT8195 vdosys1
  soc: mediatek: mmsys: add mmsys for support 64 reset bits
  soc: mediatek: add cmdq support of mtk-mmsys config API for mt8195 vdosys1
  ...

Link: https://lore.kernel.org/r/396d51fc-81f3-4a2b-d7a7-b966bfe3002a@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>