Pull pin control updates from Linus Walleij:
 "Main pin control pull request for the v3.13 cycle.

  The changes hitting arch/blackfin are ACKed by the Blackfin
  maintainer, and the device tree bindings are ACKed to the extent
  possible by someone from the device tree maintainers group.

   - Blackfin ADI pin control driver, we move yet another architecture
     under this subsystem umbrella.

   - Incremental updates to the Renesas Super-H PFC pin control driver.
     New subdriver for the r8a7791 SoC.

   - Non-linear GPIO ranges from the gpiolib side of things, this
     enabled simplified device tree bindings by referring entire groups
     of pins on some pin controller to act as back-end for a certain
     GPIO-chip driver.

   - Add the Abilis TB10x pin control driver used on the ARC
     architecture.  Also the corresponding GPIO driver is merged through
     this tree, so the ARC has full support for pins and GPIOs after
     this.

   - Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
     instances.  The i.MX1 and i.MX27 is an entirely new family
     (silicon) of controllers whereas i.MX50 is a variant of the
     previous supported controller.

   - Then the usual slew of fixes, cleanups and incremental updates"

The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.

* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
  pinctrl: imx50: add pinctrl support code for the IMX50 SoC
  pinctrl: at91: copy define to driver
  pinctrl: remove minor dead code
  pinctrl: imx: fix using pin->input_val wrongly
  pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
  gpio: tb10x: fix return value check in tb10x_gpio_probe()
  gpio: tb10x: use module_platform_driver to simplify the code
  pinctrl: imx27: imx27 pincontrol driver
  pinctrl: imx1 core driver
  pinctrl: sh-pfc: r8a7791 PFC support
  sh-pfc: r8a7778: Add CAN pin groups
  gpio: add TB10x GPIO driver
  pinctrl: at91: correct a few typos
  pinctrl: mvebu: remove redundant of_match_ptr
  pinctrl: tb10x: use module_platform_driver to simplify the code
  pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
  pinctrl: add documentation for pinctrl_get_group_pins()
  pinctrl: rockchip: emulate both edge triggered interrupts
  pinctrl: rockchip: add rk3188 specifics
  pinctrl: rockchip: remove redundant check
  ...

Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:

- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272

* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
  ARM: dts: omap5-uevm: Remove pinmux for dmic pins
  ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
  ARM: dts: TWL4030: Add power button support
  ARM: dts: omap3-n900: Add LP5523 support
  ARM: dts: omap3-n900: Add TLV320AIC3X support
  ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
  ARM: dts: omap3-n900: Add NAND support
  ARM: dts: omap3-n900: Specify regulator info
  ARM: dts: TWL4030: Add missing regulators
  ARM: dts: omap3-n900: Add LP5523 support
  ARM: dts: omap3-n900: Add vibrator device
  ARM: dts: omap3-n900: GPIO key definitions
  ARM: dts: omap3-n900: Add support for SD cards
  ARM: dts: omap3-n900: Add UART support
  ARM: dts: omap3-n900: Fix i2c bus speed
  ARM: dts: omap3-n900: Add pinctrl for i2c devices
  ARM: dts: DRA7: Add CPU OPP table
  ARM: dts: OMAP5: Add CPU OPP table
  ARM: dts: dra7-evm: add smps123 supply for CPU
  ARM: dts: omap5-uevm: add smps123 supply for CPU
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.

The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Fix AT91_PINCTRL_DEBOUNCE_VAL dt macro typo.
Fix at91_pinctrl_mux_ops callback typos.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
  the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT

* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
  ARM: ux500: fix devicetree builds
  ARM: ux500: Remove u9540.dts as it's been replaced
  ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
  ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
  ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
  ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
  ARM: ux500: Apply a ste-* prefix onto href.dtsi
  ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
  ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
  ARM: ux500: Apply a ste-* prefix onto snowball.dts
  ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
  ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
  ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
  ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
  ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
  ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
  ARM: ux500: Stop passing MMC's platform data for Device Tree boots
  Documentation: Update binding for Nomadik and DBx5x based platforms
  ARM: ux500: Supply external regulator names for Snowball's DT
  ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
  ...

This patch adds pinctrl device tree settings for uart0 and uart2
for ccu8540 board.

Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Using #include <include/...> is a bit odd. It happens to work because the DTC
flags include -Iarch/FOO/boot/dts as well as arch/FOO/boot/dts/include and
arch/FOO/boot/dts/include/dt-bindings is a symlink to include/dt-bindings.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>