linux.git/fs/ext2/file.c, branch v5.4

ext2: support statx syscall

2019-02-18T14:14:43+00:00

Since statx, every filesystem should fill the attributes/attributes_mask
in routine getattr. But the generic_fillattr has not fill that, so add
ext2_getattr to do this. This can fix generic/424 while testing ext2.

Reviewed-by: zhangyi (F) 
Signed-off-by: yangerkun 
Signed-off-by: Jan Kara

dax: remove VM_MIXEDMAP for fsdax and device dax

2018-08-17T23:20:27+00:00

This patch is reworked from an earlier patch that Dan has posted:
https://patchwork.kernel.org/patch/10131727/

VM_MIXEDMAP is used by dax to direct mm paths like vm_normal_page() that
the memory page it is dealing with is not typical memory from the linear
map.  The get_user_pages_fast() path, since it does not resolve the vma,
is already using {pte,pmd}_devmap() as a stand-in for VM_MIXEDMAP, so we
use that as a VM_MIXEDMAP replacement in some locations.  In the cases
where there is no pte to consult we fallback to using vma_is_dax() to
detect the VM_MIXEDMAP special case.

Now that we have explicit driver pfn_t-flag opt-in/opt-out for
get_user_pages() support for DAX we can stop setting VM_MIXEDMAP.  This
also means we no longer need to worry about safely manipulating vm_flags
in a future where we support dynamically changing the dax mode of a
file.

DAX should also now be supported with madvise_behavior(), vma_merge(),
and copy_page_range().

This patch has been tested against ndctl unit test.  It has also been
tested against xfstests commit: 625515d using fake pmem created by
memmap and no additional issues have been observed.

Link: http://lkml.kernel.org/r/152847720311.55924.16999195879201817653.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang 
Acked-by: Dan Williams 
Cc: Jan Kara 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

fs: ext2: Adding new return type vm_fault_t

2018-04-16T07:52:24+00:00

Use new return type vm_fault_t for page_mkwrite,
pfn_mkwrite and fault handler.

Signed-off-by: Souptick Joarder 
Reviewed-by: Matthew Wilcox 
Signed-off-by: Jan Kara

dax: pass detailed error code from dax_iomap_fault()

2018-01-07T21:38:43+00:00

Ext4 needs to pass through error from its iomap handler to the page
fault handler so that it can properly detect ENOSPC and force
transaction commit and retry the fault (and block allocation). Add
argument to dax_iomap_fault() for passing such error.

Reviewed-by: Ross Zwisler 
Signed-off-by: Jan Kara 
Signed-off-by: Theodore Ts'o

Merge tag 'libnvdimm-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm

2017-11-17T17:51:57+00:00

Pull libnvdimm and dax updates from Dan Williams:
 "Save for a few late fixes, all of these commits have shipped in -next
  releases since before the merge window opened, and 0day has given a
  build success notification.

  The ext4 touches came from Jan, and the xfs touches have Darrick's
  reviewed-by. An xfstest for the MAP_SYNC feature has been through
  a few round of reviews and is on track to be merged.

   - Introduce MAP_SYNC and MAP_SHARED_VALIDATE, a mechanism to enable
     'userspace flush' of persistent memory updates via filesystem-dax
     mappings. It arranges for any filesystem metadata updates that may
     be required to satisfy a write fault to also be flushed ("on disk")
     before the kernel returns to userspace from the fault handler.
     Effectively every write-fault that dirties metadata completes an
     fsync() before returning from the fault handler. The new
     MAP_SHARED_VALIDATE mapping type guarantees that the MAP_SYNC flag
     is validated as supported by the filesystem's ->mmap() file
     operation.

   - Add support for the standard ACPI 6.2 label access methods that
     replace the NVDIMM_FAMILY_INTEL (vendor specific) label methods.
     This enables interoperability with environments that only implement
     the standardized methods.

   - Add support for the ACPI 6.2 NVDIMM media error injection methods.

   - Add support for the NVDIMM_FAMILY_INTEL v1.6 DIMM commands for
     latch last shutdown status, firmware update, SMART error injection,
     and SMART alarm threshold control.

   - Cleanup physical address information disclosures to be root-only.

   - Fix revalidation of the DIMM "locked label area" status to support
     dynamic unlock of the label area.

   - Expand unit test infrastructure to mock the ACPI 6.2 Translate SPA
     (system-physical-address) command and error injection commands.

  Acknowledgements that came after the commits were pushed to -next:

   - 957ac8c421ad ("dax: fix PMD faults on zero-length files"):
       Reviewed-by: Ross Zwisler 

   - a39e596baa07 ("xfs: support for synchronous DAX faults") and
     7b565c9f965b ("xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()")
        Reviewed-by: Darrick J. Wong "

* tag 'libnvdimm-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (49 commits)
  acpi, nfit: add 'Enable Latch System Shutdown Status' command support
  dax: fix general protection fault in dax_alloc_inode
  dax: fix PMD faults on zero-length files
  dax: stop requiring a live device for dax_flush()
  brd: remove dax support
  dax: quiet bdev_dax_supported()
  fs, dax: unify IOMAP_F_DIRTY read vs write handling policy in the dax core
  tools/testing/nvdimm: unit test clear-error commands
  acpi, nfit: validate commands against the device type
  tools/testing/nvdimm: stricter bounds checking for error injection commands
  xfs: support for synchronous DAX faults
  xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()
  ext4: Support for synchronous DAX faults
  ext4: Simplify error handling in ext4_dax_huge_fault()
  dax: Implement dax_finish_sync_fault()
  dax, iomap: Add support for synchronous faults
  mm: Define MAP_SYNC and VM_SYNC flags
  dax: Allow tuning whether dax_insert_mapping_entry() dirties entry
  dax: Allow dax_iomap_fault() to return pfn
  dax: Fix comment describing dax_iomap_fault()
  ...

dax: Allow dax_iomap_fault() to return pfn

2017-11-03T13:26:24+00:00

For synchronous page fault dax_iomap_fault() will need to return PFN
which will then need to be inserted into page tables after fsync()
completes. Add necessary parameter to dax_iomap_fault().

Reviewed-by: Christoph Hellwig 
Reviewed-by: Ross Zwisler 
Signed-off-by: Jan Kara 
Signed-off-by: Dan Williams

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55+00:00

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart 
Reviewed-by: Philippe Ombredanne 
Reviewed-by: Thomas Gleixner 
Signed-off-by: Greg Kroah-Hartman

dax: use common 4k zero page for dax mmap reads

2017-09-07T00:27:24+00:00

When servicing mmap() reads from file holes the current DAX code
allocates a page cache page of all zeroes and places the struct page
pointer in the mapping->page_tree radix tree.

This has three major drawbacks:

1) It consumes memory unnecessarily. For every 4k page that is read via
   a DAX mmap() over a hole, we allocate a new page cache page. This
   means that if you read 1GiB worth of pages, you end up using 1GiB of
   zeroed memory. This is easily visible by looking at the overall
   memory consumption of the system or by looking at /proc/[pid]/smaps:

	7f62e72b3000-7f63272b3000 rw-s 00000000 103:00 12   /root/dax/data
	Size:            1048576 kB
	Rss:             1048576 kB
	Pss:             1048576 kB
	Shared_Clean:          0 kB
	Shared_Dirty:          0 kB
	Private_Clean:   1048576 kB
	Private_Dirty:         0 kB
	Referenced:      1048576 kB
	Anonymous:             0 kB
	LazyFree:              0 kB
	AnonHugePages:         0 kB
	ShmemPmdMapped:        0 kB
	Shared_Hugetlb:        0 kB
	Private_Hugetlb:       0 kB
	Swap:                  0 kB
	SwapPss:               0 kB
	KernelPageSize:        4 kB
	MMUPageSize:           4 kB
	Locked:                0 kB

2) It is slower than using a common zero page because each page fault
   has more work to do. Instead of just inserting a common zero page we
   have to allocate a page cache page, zero it, and then insert it. Here
   are the average latencies of dax_load_hole() as measured by ftrace on
   a random test box:

    Old method, using zeroed page cache pages:	3.4 us
    New method, using the common 4k zero page:	0.8 us

   This was the average latency over 1 GiB of sequential reads done by
   this simple fio script:

     [global]
     size=1G
     filename=/root/dax/data
     fallocate=none
     [io]
     rw=read
     ioengine=mmap

3) The fact that we had to check for both DAX exceptional entries and
   for page cache pages in the radix tree made the DAX code more
   complex.

Solve these issues by following the lead of the DAX PMD code and using a
common 4k zero page instead.  As with the PMD code we will now insert a
DAX exceptional entry into the radix tree instead of a struct page
pointer which allows us to remove all the special casing in the DAX
code.

Note that we do still pretty aggressively check for regular pages in the
DAX radix tree, especially where we take action based on the bits set in
the page.  If we ever find a regular page in our radix tree now that
most likely means that someone besides DAX is inserting pages (which has
happened lots of times in the past), and we want to find that out early
and fail loudly.

This solution also removes the extra memory consumption.  Here is that
same /proc/[pid]/smaps after 1GiB of reading from a hole with the new
code:

	7f2054a74000-7f2094a74000 rw-s 00000000 103:00 12   /root/dax/data
	Size:            1048576 kB
	Rss:                   0 kB
	Pss:                   0 kB
	Shared_Clean:          0 kB
	Shared_Dirty:          0 kB
	Private_Clean:         0 kB
	Private_Dirty:         0 kB
	Referenced:            0 kB
	Anonymous:             0 kB
	LazyFree:              0 kB
	AnonHugePages:         0 kB
	ShmemPmdMapped:        0 kB
	Shared_Hugetlb:        0 kB
	Private_Hugetlb:       0 kB
	Swap:                  0 kB
	SwapPss:               0 kB
	KernelPageSize:        4 kB
	MMUPageSize:           4 kB
	Locked:                0 kB

Overall system memory consumption is similarly improved.

Another major change is that we remove dax_pfn_mkwrite() from our fault
flow, and instead rely on the page fault itself to make the PTE dirty
and writeable.  The following description from the patch adding the
vm_insert_mixed_mkwrite() call explains this a little more:

   "To be able to use the common 4k zero page in DAX we need to have our
    PTE fault path look more like our PMD fault path where a PTE entry
    can be marked as dirty and writeable as it is first inserted rather
    than waiting for a follow-up dax_pfn_mkwrite() =>
    finish_mkwrite_fault() call.

    Right now we can rely on having a dax_pfn_mkwrite() call because we
    can distinguish between these two cases in do_wp_page():

            case 1: 4k zero page => writable DAX storage
            case 2: read-only DAX storage => writeable DAX storage

    This distinction is made by via vm_normal_page(). vm_normal_page()
    returns false for the common 4k zero page, though, just as it does
    for DAX ptes. Instead of special casing the DAX + 4k zero page case
    we will simplify our DAX PTE page fault sequence so that it matches
    our DAX PMD sequence, and get rid of the dax_pfn_mkwrite() helper.
    We will instead use dax_iomap_fault() to handle write-protection
    faults.

    This means that insert_pfn() needs to follow the lead of
    insert_pfn_pmd() and allow us to pass in a 'mkwrite' flag. If
    'mkwrite' is set insert_pfn() will do the work that was previously
    done by wp_page_reuse() as part of the dax_pfn_mkwrite() call path"

Link: http://lkml.kernel.org/r/20170724170616.25810-4-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler 
Reviewed-by: Jan Kara 
Cc: "Darrick J. Wong" 
Cc: "Theodore Ts'o" 
Cc: Alexander Viro 
Cc: Andreas Dilger 
Cc: Christoph Hellwig 
Cc: Dan Williams 
Cc: Dave Chinner 
Cc: Ingo Molnar 
Cc: Jonathan Corbet 
Cc: Matthew Wilcox 
Cc: Steven Rostedt 
Cc: Kirill A. Shutemov 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

fs: check for writeback errors after syncing out buffers in generic_file_fsync

2017-07-06T11:02:21+00:00

ext2 currently does a test+clear of the AS_EIO flag, which is
is problematic for some coming changes.

What we really need to do instead is call filemap_check_errors
in __generic_file_fsync after syncing out the buffers. That
will be sufficient for this case, and help other callers detect
these errors properly as well.

With that, we don't need to twiddle it in ext2.

Suggested-by: Jan Kara 
Signed-off-by: Jeff Layton 
Reviewed-by: Christoph Hellwig 
Reviewed-by: Jan Kara 
Reviewed-by: Matthew Wilcox

mm: replace FAULT_FLAG_SIZE with parameter to huge_fault

2017-02-25T01:46:54+00:00

Since the introduction of FAULT_FLAG_SIZE to the vm_fault flag, it has
been somewhat painful with getting the flags set and removed at the
correct locations.  More than one kernel oops was introduced due to
difficulties of getting the placement correctly.

Remove the flag values and introduce an input parameter to huge_fault
that indicates the size of the page entry.  This makes the code easier
to trace and should avoid the issues we see with the fault flags where
removal of the flag was necessary in the fallback paths.

Link: http://lkml.kernel.org/r/148615748258.43180.1690152053774975329.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang 
Tested-by: Dan Williams 
Reviewed-by: Jan Kara 
Cc: Matthew Wilcox 
Cc: Dave Hansen 
Cc: Vlastimil Babka 
Cc: Ross Zwisler 
Cc: Kirill A. Shutemov 
Cc: Nilesh Choudhury 
Cc: Ingo Molnar 
Cc: "H. Peter Anvin" 
Cc: Thomas Gleixner 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds