- Improved flow control and simplified interface
- Use hardware RSS indirection table instead of the slower firmware-
  based table
- Lower latency interrupt on 5709

Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode.  This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Switch to the new firmware version (5.2.13).

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs,serial_cs:

add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/usb/cdc_ether.c

All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.

Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs,serial_cs:

add cis of PreMax ethernet pcmcia card,
and some Sierra Wireless serial card(AC555, AC7xx, AC8xx).

use PROD_ID for AC7xx, because MANF_ID of AC7xx and AC8xx are the same.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs,serial_cs:
  
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (133 commits)
  drm/vgaarb: add VGA arbitration support to the drm and kms.
  drm/radeon: some r420s have a CP race with the DMA engine.
  drm/radeon/r600/kms: rv670 is not DCE3
  drm/radeon/kms: r420 idle after programming GA_ENHANCE
  drm/radeon/kms: more fixes to rv770 suspend/resume path.
  drm/radeon/kms: more alignment for rv770.c with r600.c
  drm/radeon/kms: rv770 blit init called too late.
  drm/radeon/kms: move around new init path code to avoid posting at init
  drm/radeon/r600: fix some issues with suspend/resume.
  drm/radeon/kms: disable VGA rendering engine before taking over VRAM
  drm/radeon/kms: Move radeon_get_clock_info() call out of radeon_clocks_init().
  drm/radeon/kms: add initial connector properties
  drm/radeon/kms: Use surfaces for scanout / cursor byte swapping on big endian.
  drm/radeon/kms: don't fail if we fail to init GPU acceleration
  drm/r600/kms: fixup number of loops per blit calculation.
  drm/radeon/kms: reprogram format in set base.
  drm/radeon: avivo chips have no separate int bit for display
  drm/radeon/r600: don't do interrupts
  drm: fix _DRM_GEM addmap error message
  drm: update crtc x/y when only fb changes
  ...

Fixed up trivial conflicts in firmware/Makefile due to network driver
(cxgb3) and drm (mga/r128/radeon) firmware being listed next to each
other.