linux.git/drivers/w1, branch v3.0-rc2

w1: add Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC support

2011-05-27T00:12:38+00:00

Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.

It was suggested to combine this functionality with the current ds2782
driver.  Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.

[akpm@linux-foundation.org: use min_t()]
Signed-off-by: Clifton Barnes 
Tested-by: Haojian Zhuang 
Cc: Evgeniy Polyakov 
Cc: Ryan Mallon 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

w1: have netlink search update kernel list

2011-05-27T00:12:38+00:00

Reorganize so the netlink connector one wire search command will update
the kernel list of detected slave devices.  Otherwise, a newly detected
device is unusable because unless it's in the kernel list of known devices
any commands will result in ENODEV status.

Signed-off-by: David Fries 
Cc: Evgeniy Polyakov 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

w1: complete the 1-wire (w1) ds1wm driver search algorithm

2011-05-27T00:12:38+00:00

This adds multi-slave support of the w1 bus for the ds1wm Synthesizable
1-Wire Bus Master.  Also many fixes and tweaks based on the rev3 of the
datasheet http://datasheets.maxim-ic.com/en/ds/DS1WM.pdf

Signed-off-by: Jean-François Dagenais 
Cc: Evgeniy Polyakov 
Cc: Szabolcs Gyurko 
Cc: Matt Reimer 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

w1: add 1-wire (w1) DS2408 8-Channel Addressable Switch support

2011-05-27T00:12:38+00:00

This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.

[randy.dunlap@oracle.com: fix w1_ds2408.c printk formats]
Signed-off-by: Jean-François Dagenais 
Cc: Evgeniy Polyakov 
Cc: Szabolcs Gyurko 
Cc: Matt Reimer 
Signed-off-by: Randy Dunlap 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

w1: add 1-wire (w1) reset and resume command API support

2011-05-27T00:12:38+00:00

The first patch adds generic functionnality to w1_io for Resume Command
[A5h] lots of slaves support.  I found it useful for multi-commands/reset
workflows with the same slave on a multi-slave bus.

This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.  Enjoy!

The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK.  I took them
out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA
through pcie) and found them irrelevant.

The clock freq/divisors at the top of ds1wm.c did not have the MSB set to
1.  This bit is CLK_EN which turns the whole prescaler and dividers on.
The driver never mentionned this bit either, so I just included this bit
right in the table entries.  I also took the liberty to add a couple of
entries to the table.  The spec doesn't explicitely mentions these
possibilities but the description and examination of the core shows the
prescalers & dividers can be used for more than the table explicitely
shows.  The table I enlarged still doesn't cover all possibilities, but
it's a good start.

I also made a few tweaks to a couple of the read and write algorithms
which made sense while I had my head very deep in the ds1wm documentation.
 We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and
ds2433 at the same time doing extensive interaction.  It proved quite
stable in our production environment.

This patch:

Add generic functionnality to w1_io for Resume Command [A5h] lots of
slaves support.

Signed-off-by: Jean-François Dagenais 
Cc: Evgeniy Polyakov 
Cc: Szabolcs Gyurko 
Cc: Matt Reimer 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

w1: Use device platform_data to retrieve ds1wm platform bits

2011-05-26T17:45:00+00:00

With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data().

Cc: Matt Reimer 
Cc: Philipp Zabel 
Signed-off-by: Samuel Ortiz

Fix common misspellings

2011-03-31T14:26:23+00:00

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi

drivers: Final irq namespace conversion

2011-03-29T12:48:19+00:00

Scripted with coccinelle.

Signed-off-by: Thomas Gleixner

w1: Silence ds1wm warnings related to mfd_get_cell changes

2011-03-23T09:42:02+00:00

mfd_get_cell returns a const, so change the ds1wm client to store
a const mfd cell.  This silences type mismatch warnings.

Since we're guaranteed to have the mfd_cell, we can also simplify
the code a bit to get rid of a temporary variable and NULL check.

Signed-off-by: Andres Salomon 
Signed-off-by: Samuel Ortiz

w1: Use mfd_data instead of driver_data for dsw1wm.c

2011-03-23T09:41:56+00:00

Use mfd_data for passing information from mfd drivers to mfd
clients.  The mfd_cell's driver_data field is being phased out.

Clients that were using driver_data now access .mfd_data
via mfd_get_data().  This changes ds1wm only; mfd drivers with
other cells are not modified, with the exception of led_cell.

The led_cell.driver_data line is dropped from htc-pasic3.c in this
patch as well.  It's not used in mainline (there's no leds-pasic3
platform driver), so it should be safe to take care of that here.

Signed-off-by: Andres Salomon 
Signed-off-by: Samuel Ortiz