Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes and quirk updates for 5.0-rc2.

  The majority here are some quirks for some storage devices to get them
  to work properly. There's also a fix here to resolve the reported
  issues with some audio devices that say they are UAC3 compliant, but
  really are not.

  And a fix up for the MAINTAINERS file to remove a dead url.

  All have been in linux-next with no reported issues"

* tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: storage: Remove outdated URL from MAINTAINERS
  USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB
  usbcore: Select only first configuration for non-UAC3 compliant devices
  USB: storage: add quirk for SMI SM3350
  USB: storage: don't insert sane sense for SPC3+ when bad sense specified
  usb: cdc-acm: send ZLP for Telit 3G Intel based modems

We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.

This change was generated with the following Coccinelle SmPL patch:

@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@

-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)

Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>

To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.

Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20")

Previous K70 RGB patch to add delay-init quirk:
7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards")

Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In most of the UAC1 and UAC2 audio devices, the first
configuration is most often the best configuration.
However, with recent patch to support UAC3 configuration,
second configuration was unintentionally chosen for
some of the UAC1/2 devices that had more than one
configuration. This was because of the existing check
after the audio config check which selected any config
which had a non-vendor class. This patch fixes this issue.

Fixes: f13912d3f014 ("usbcore: Select UAC3 configuration for audio if present")
Reported-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Tested-by: Con Kolivas <kernel@kolivas.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The SMI SM3350 USB-UFS bridge controller cannot handle long sense request
correctly and will make the chip refuse to do read/write when requested
long sense.

Add a bad sense quirk for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the code will set US_FL_SANE_SENSE flag unconditionally if
device claims SPC3+, however we should allow US_FL_BAD_SENSE flag to
prevent this behavior, because SMI SM3350 UFS-USB bridge controller,
which claims SPC4, will show strange behavior with 96-byte sense
(put the chip into a wrong state that cannot read/write anything).

Check the presence of US_FL_BAD_SENSE when assuming US_FL_SANE_SENSE on
SPC4+ devices.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Telit 3G Intel based modems require zero packet to be sent if
out data size is equal to the endpoint max packet size.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull PCI updates from Bjorn Helgaas:

 - Remove unused lists from ASPM pcie_link_state (Frederick Lawler)

 - Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
   King)

 - Expand Kconfig "PF" acronyms (Randy Dunlap)

 - Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)

 - Add missing include to drivers/pci.h (Alexandru Gagniuc)

 - Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
   instead of xhci (Thinh Nguyen)

 - Clean up P2PDMA documentation (Randy Dunlap)

 - Allow runtime PM even if driver doesn't supply callbacks (Jarkko
   Nikula)

 - Remove status check after submitting Switchtec MRPC Firmware Download
   commands to avoid Completion Timeouts (Kelvin Cao)

 - Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)

 - Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
   (Joey Zhang)

 - Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)

 - Add Switchtec MRPC DMA mode support (Wesley Sheng)

 - Skip VF scanning on powerpc, which does this in firmware (Sebastian
   Ott)

 - Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)

 - Constify histb dw_pcie_host_ops structure (Julia Lawall)

 - Support multiple power domains for imx6 (Leonard Crestez)

 - Constify layerscape driver data (Stefan Agner)

 - Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)

 - Support armada8k GPIO reset (Baruch Siach)

 - Support suspend/resume support on imx6 (Leonard Crestez)

 - Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)

 - Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)

 - Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)

 - Mask DesignWare interrupts instead of disabling them to avoid lost
   interrupts (Marc Zyngier)

 - Add locking when acking DesignWare interrupts (Marc Zyngier)

 - Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)

 - Use devm resource parser in mediatek (Honghui Zhang)

 - Remove unused mediatek "num-lanes" DT property (Honghui Zhang)

 - Add UniPhier PCIe controller driver and DT bindings (Kunihiko
   Hayashi)

 - Enable MSI for imx6 downstream components (Richard Zhu)

* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
  PCI: imx: Enable MSI from downstream components
  s390/pci: skip VF scanning
  PCI/IOV: Add flag so platforms can skip VF scanning
  PCI/IOV: Factor out sriov_add_vfs()
  PCI: uniphier: Add UniPhier PCIe host controller support
  dt-bindings: PCI: Add UniPhier PCIe host controller description
  PCI: amlogic: Add the Amlogic Meson PCIe controller driver
  dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
  arm64: dts: mt7622: Remove un-used property for PCIe
  arm: dts: mt7623: Remove un-used property for PCIe
  dt-bindings: PCI: MediaTek: Remove un-used property
  PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
  MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
  PCI: dwc: Don't hard-code DBI/ATU offset
  PCI: imx: Add imx6sx suspend/resume support
  PCI: armada8k: Add support for gpio controlled reset signal
  PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
  PCI: dwc: layerscape: Constify driver data
  PCI: imx: Add multi-pd support
  PCI: Override Synopsys USB 3.x HAPS device class
  ...

Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.

It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access.  But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.

A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model.  And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.

This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.

There were a couple of notable cases:

 - csky still had the old "verify_area()" name as an alias.

 - the iter_iov code had magical hardcoded knowledge of the actual
   values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
   really used it)

 - microblaze used the type argument for a debug printout

but other than those oddities this should be a total no-op patch.

I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something.  Any missed conversion should be trivially fixable, though.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull IOMMU updates from Joerg Roedel:

 - Page table code for AMD IOMMU now supports large pages where smaller
   page-sizes were mapped before. VFIO had to work around that in the
   past and I included a patch to remove it (acked by Alex Williamson)

 - Patches to unmodularize a couple of IOMMU drivers that would never
   work as modules anyway.

 - Work to unify the the iommu-related pointers in 'struct device' into
   one pointer. This work is not finished yet, but will probably be in
   the next cycle.

 - NUMA aware allocation in iommu-dma code

 - Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver

 - Scalable mode support for the Intel VT-d driver

 - PM runtime improvements for the ARM-SMMU driver

 - Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom

 - Various smaller fixes and improvements

* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
  iommu: Check for iommu_ops == NULL in iommu_probe_device()
  ACPI/IORT: Don't call iommu_ops->add_device directly
  iommu/of: Don't call iommu_ops->add_device directly
  iommu: Consolitate ->add/remove_device() calls
  iommu/sysfs: Rename iommu_release_device()
  dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
  xhci: Use device_iommu_mapped()
  powerpc/iommu: Use device_iommu_mapped()
  ACPI/IORT: Use device_iommu_mapped()
  iommu/of: Use device_iommu_mapped()
  driver core: Introduce device_iommu_mapped() function
  iommu/tegra: Use helper functions to access dev->iommu_fwspec
  iommu/qcom: Use helper functions to access dev->iommu_fwspec
  iommu/of: Use helper functions to access dev->iommu_fwspec
  iommu/mediatek: Use helper functions to access dev->iommu_fwspec
  iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
  iommu/dma: Use helper functions to access dev->iommu_fwspec
  iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
  ACPI/IORT: Use helper functions to access dev->iommu_fwspec
  iommu: Introduce wrappers around dev->iommu_fwspec
  ...