Pull USB fixes from Greg KH:
 "Here are a number of small USB fixes for 4.20-rc4.

  There's the usual xhci and dwc2/3 fixes as well as a few minor other
  issues resolved for problems that have been reported. Full details are
  in the shortlog.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: cdc-acm: add entry for Hiro (Conexant) modem
  usb: xhci: Prevent bus suspend if a port connect change or polling state is detected
  usb: core: Fix hub port connection events lost
  usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
  Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
  usb: dwc2: pci: Fix an error code in probe
  usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
  xhci: Add quirk to workaround the errata seen on Cavium Thunder-X2 Soc
  usb: xhci: fix timeout for transition from RExit to U0
  usb: xhci: fix uninitialized completion when USB3 port got wrong status
  xhci: Add check for invalid byte size error when UAS devices are connected.
  xhci: handle port status events for removed USB3 hcd
  xhci: Fix leaking USB3 shared_hcd at xhci removal
  USB: misc: appledisplay: add 20" Apple Cinema Display
  USB: quirks: Add no-lpm quirk for Raydium touchscreens
  usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB
  USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hub
  usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
  usb: dwc3: core: Clean up ULPI device

The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
	idVendor	0x0572
	idProduct	0x1349

Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.

USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.

If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.

The hub thread will notice the connect change and resume the bus,
moving the port back to U0

This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted

Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().

Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.

Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.

This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.

Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

For now only 5 small fixes. Most importantly, we have a fix for the TRB
type used on unaligned transfers on dwc3. Also a fix for a NULL pointer
dereference in dwc3_pci_remove(). Note that a recent commit on ffs was
reverted because it causes a regression elsewere.

* tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
  Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
  usb: dwc2: pci: Fix an error code in probe
  usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
  usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
  usb: dwc3: core: Clean up ULPI device

When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.

Fixes: c6267a51639b ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit b4194da3f9087dd38d91b40f9bec42d59ce589a8
since it causes list corruption followed by kernel panic:

Workqueue: adb ffs_aio_cancel_worker
RIP: 0010:__list_add_valid+0x4d/0x70
Call Trace:
insert_work+0x47/0xb0
__queue_work+0xf6/0x400
queue_work_on+0x65/0x70
dwc3_gadget_giveback+0x44/0x50 [dwc3]
dwc3_gadget_ep_dequeue+0x83/0x2d0 [dwc3]
? finish_wait+0x80/0x80
usb_ep_dequeue+0x1e/0x90
process_one_work+0x18c/0x3b0
worker_thread+0x3c/0x390
? process_one_work+0x3b0/0x3b0
kthread+0x11e/0x140
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x3a/0x50

This issue is seen with warm reboot stability testing.

Signed-off-by: Shen Jing <jingx.shen@intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We added some error handling to this function but forgot to set the
error code on this path.

Fixes: ecd29dabb2ba ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.

Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Latest NVIDIA GPU cards have a Cypress CCGx Type-C controller
over I2C interface.

This UCSI I2C driver uses I2C bus driver interface for communicating
with Type-C controller.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>