Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes and new device ids for
  4.13-rc5. There is the usual gadget driver fixes, some new quirks for
  "messy" hardware, and some new device ids.

  All have been in linux-next with no reported issues"

* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: pl2303: add new ATEN device id
  usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
  USB: Check for dropped connection before switching to full speed
  usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
  usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
  usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
  usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
  usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
  usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
  USB: serial: option: add D-Link DWM-222 device ID
  usb: musb: fix tx fifo flush handling again
  usb: core: unlink urbs from the tail of the endpoint's urb_list
  usb-storage: fix deadlock involving host lock and scsi_done
  uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
  USB: hcd: Mark secondary HCD as dead if the primary one died
  USB: serial: cp210x: add support for Qivicon USB ZigBee dongle

This adds a new ATEN device id for a new pl2303-based device.

Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: stable <stable@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.

The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.

Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure.  This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.

The logic for doing this is careful to check that the device is still
connected.  But this check is inadequate if the device disconnects and
reconnects before the check is done.  The symptom is that a device
works, but much more slowly than it is capable of operating.

The situation was made worse recently by commit 22547c4cc4fe ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.

This patch makes the check more robust.  If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume

On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.

In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.

As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.

Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Johan writes:

USB-serial fixes for v4.13-rc4

Here are some new device ids for v4.13-rc4.

All have been in linux-next with no reported issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

Felipe writes:

usb: fixes for v4.13-rc4

Another fix for isochronous transfers on dwc3. This time around, we're
making sure that we use correct PIDs in all transfer sizes.

MSM PHY driver got a fix for the use of devm_regulator_bulk_get() API
which will avoid kernel crashes.

Renesas DRD driver got 3 fixes: a fix on giveback, a fix for proper
controller programming and the removal of set-but-never-used variable.

The commit b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps
when the driver stops") causes the unused-but-set-variable warning.
But, if the usbhsg_ep_disable() will return non-zero value, udc/core.c
doesn't clear the ep->enabled flag. So, this driver should not return
non-zero value, if the pipe is zero because this means the pipe is
already disabled. Otherwise, the ep->enabled flag is never cleared
when the usbhsg_ep_disable() is called by the renesas_usbhs driver first.

Fixes: b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Fixes: 11432050f070 ("usb: renesas_usbhs: gadget: fix NULL pointer dereference in ep_disable()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit.
If the bit sets to 1, the VBUS drive is controlled by phy related
registers (called "UCOM Registers" on the manual). Since R-Car Gen3
environment will control VBUS by phy-rcar-gen3-usb2 driver,
the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes
the register's value. Otherwise, even if the ID pin indicates to
peripheral, the R-Car will output USBn_PWEN to 1 when a host driver
is running.

Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control"
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The regulator_bulk_data pointer passed to devm_regulator_bulk_get()
is used to store the client handles for the regulators, which
is later used by devm_regulator_bulk_release() to free the
regulators.
Passing a local array as is done here means the memory used to
store the handles is freed causing the handles to be corrupted,
resulting in a crash when devm_regulator_bulk_release() tries to
free them.

Fix this my moving the array inside of the msm_otg structure.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>