Johan writes:

USB-serial fixes for v4.12-rc2

Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.

A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.

Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.

All have been in linux-next with no reported issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.

To fix this issue, only modify the TX or RX part of the register.

Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit d8e5f0eca1e8 ("usb: musb: Fix hardirq-safe hardirq-unsafe
lock order error") caused a regression where musb keeps trying to
enable host mode with no cable connected. This seems to be caused
by the fact that now phy is enabled earlier, and we are wrongly
trying to force USB host mode on an OTG port. The errors we are
getting are "trying to suspend as a_idle while active".

For ports configured as OTG, we should not need to do anything
to try to force USB host mode on it's OTG port. Trying to force host
mode in this case just seems to completely confuse the musb state
machine.

Let's fix the issue by making musb_host_setup() attempt to force the
mode only if port_mode is configured for host mode.

Fixes: d8e5f0eca1e8 ("usb: musb: Fix hardirq-safe hardirq-unsafe lock order error")
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.

CC: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In 4.11 TRB completion codes were renamed to match spec.

Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.

Use the correct completion code for command ring stopped events.

Fixes: 0b7c105a04ca ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no reason to restrict allocations to the first 16MB ISA DMA
addresses.

It is causing problems in a virtualization setup with enabled IOMMU
(x86_64). The result is that USB is not working in the VM.

CC: <stable@vger.kernel.org>
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With threaded interrupts, bottom-half handlers are called with
interrupts enabled.  Therefore they can't safely use spin_lock(); they
have to use spin_lock_irqsave().  Lockdep warns about a violation
occurring in xhci_irq():

=========================================================
[ INFO: possible irq lock inversion dependency detected ]
4.11.0-rc8-dbg+ #1 Not tainted
---------------------------------------------------------
swapper/7/0 just changed the state of lock:
 (&(&ehci->lock)->rlock){-.-...}, at: [<ffffffffa0130a69>]
ehci_hrtimer_func+0x29/0xc0 [ehci_hcd]
but this lock took another, HARDIRQ-unsafe lock in the past:
 (hcd_urb_list_lock){+.....}

and interrupts could create inverse lock ordering between them.

other info that might help us debug this:
 Possible interrupt unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(hcd_urb_list_lock);
                               local_irq_disable();
                               lock(&(&ehci->lock)->rlock);
                               lock(hcd_urb_list_lock);
  <Interrupt>
    lock(&(&ehci->lock)->rlock);
 *** DEADLOCK ***

no locks held by swapper/7/0.
the shortest dependencies between 2nd lock and 1st lock:
 -> (hcd_urb_list_lock){+.....} ops: 252 {
    HARDIRQ-ON-W at:
                      __lock_acquire+0x602/0x1280
                      lock_acquire+0xd5/0x1c0
                      _raw_spin_lock+0x2f/0x40
                      usb_hcd_unlink_urb_from_ep+0x1b/0x60 [usbcore]
                      xhci_giveback_urb_in_irq.isra.45+0x70/0x1b0 [xhci_hcd]
                      finish_td.constprop.60+0x1d8/0x2e0 [xhci_hcd]
                      xhci_irq+0xdd6/0x1fa0 [xhci_hcd]
                      usb_hcd_irq+0x26/0x40 [usbcore]
                      irq_forced_thread_fn+0x2f/0x70
                      irq_thread+0x149/0x1d0
                      kthread+0x113/0x150
                      ret_from_fork+0x2e/0x40

This patch fixes the problem.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram

	If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
       	then the assertion of the Interrupt Pending (IP) flag in Figure 30
       	generates a PCI Dword write. The IP flag is automatically cleared
       	by the completion of the PCI write.

the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.

	...
	The following operations take place to allocate
       	Scratchpad Buffers to the xHC:
	...
		b. Software clears the Scratchpad Buffer to '0'

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>