Pull gadgetfs fixes from Al Viro:
 "Assorted fixes around AIO on gadgetfs: leaks, use-after-free, troubles
  caused by ->f_op flipping"

* 'gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  gadgetfs: really get rid of switching ->f_op
  gadgetfs: get rid of flipping ->f_op in ep_config()
  gadget: switch ep_io_operations to ->read_iter/->write_iter
  gadgetfs: use-after-free in ->aio_read()
  gadget/function/f_fs.c: switch to ->{read,write}_iter()
  gadget/function/f_fs.c: use put iov_iter into io_data
  gadget/function/f_fs.c: close leaks
  move iov_iter.c from mm/ to lib/
  new helper: dup_iter()

Pull USB fixes from Greg KH:
 "Here's a round of USB fixes for 4.0-rc3.

  Nothing major, the usual gadget, xhci and usb-serial fixes and a few
  new device ids as well.

  All have been in linux-next successfully"

* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
  xhci: Workaround for PME stuck issues in Intel xhci
  xhci: fix reporting of 0-sized URBs in control endpoint
  usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
  USB: ch341: set tty baud speed according to tty struct
  USB: serial: cp210x: Adding Seletek device id's
  USB: pl2303: disable break on shutdown
  USB: mxuport: fix null deref when used as a console
  USB: serial: clean up bus probe error handling
  USB: serial: fix port attribute-creation race
  USB: serial: fix tty-device error handling at probe
  USB: serial: fix potential use-after-free after failed probe
  USB: console: add dummy __module_get
  USB: ftdi_sio: add PIDs for Actisense USB devices
  Revert "USB: serial: make bulk_out_size a lower limit"
  cdc-acm: Add support for Denso cradle CU-321
  usb-storage: support for more than 8 LUNs
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
  USB: usbfs: don't leak kernel data in siginfo
  xhci: Clear the host side toggle manually when endpoint is 'soft reset'
  xhci: Allocate correct amount of scratchpad buffers
  ...

... for ep0 as well

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Final methods start with get_ready_ep(), which will fail unless we have
->state == STATE_EP_ENABLED.  So they'd be failing just fine until that
first write() anyway.  Let's do the following:
	* get_ready_ep() gets a new argument - true when called from
ep_write_iter(), false otherwise.
	* make it quiet when it finds STATE_EP_READY (no printk, that is;
the case won't be impossible after that change).
	* when that new argument is true, treat STATE_EP_READY the same
way as STATE_EP_ENABLED (i.e. return zero and do not unlock).
	* in ep_write_iter(), after success of get_ready_ep() turn
	if (!usb_endpoint_dir_in(&epdata->desc)) {
into
	if (epdata->state == STATE_EP_ENABLED &&
	    !usb_endpoint_dir_in(&epdata->desc)) {
- that logics only applies after config.
	* have ep_config() take kernel-side buffer (i.e. use memcpy()
instead of copy_from_user() in there) and in the "let's call ep_io or
ep_aio" (again, in ep_write_iter()) add "... or ep_config() in case it's
not configured yet"

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Make sure to handle an infinite timeout (0).

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: dcf010503966 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org>	# v3.10

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.

Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks

Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)

Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.

The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.

This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.

This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.

Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Johan writes:

USB-serial fixes for v4.0-rc3

Here are a few fixes for reported problems including a usb-debug device
buffer overflow, potential use-after-free on failed probe, and a couple
of issues with the USB console.

Some new device IDs are also added.

Signed-off-by: Johan Hovold <johan@kernel.org>

This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.

Steps: 2

[ftdi_sio_ids.h]
1. Defined the device PID

[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.

Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The ch341_set_baudrate() function initialize the device baud speed
according to the value on priv->baud_rate. By default the ch341_open() set
it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the
tty_struct is not initialized with the same default value. (usually 56700)

This means that the tty_struct and the device baud rate generator are not
synchronized after opening the port.

Fixup is done by calling ch341_set_termios() if tty exist.
Remove unnecessary variable priv->baud_rate setup as it's already done by
ch341_port_probe().
Remove unnecessary call to ch341_set_{handshake,baudrate}() in
ch341_open() as there already called in ch341_configure() and
ch341_set_termios()

Signed-off-by: Nicolas PLANEL <nicolas.planel@enovance.com>
Signed-off-by: Johan Hovold <johan@kernel.org>